IPoIB's required behaviour w.r.t to the pkey used by the device is the following:
- For "parent" interfaces (e.g ib0, ib1, etc) who are created
automatically as a result of hot-plug events from the IB core, the
driver needs to take whatever pkey vlaue it finds in index 0, and
stick to that index.
- For child interfaces (e.g ib0.8001, etc) created by admin directive,
the driver needs to use and stick to the value provided during its
creation.
In SR-IOV environment its possible for the VF probe to take place
before the cloud management software provisions the suitable pkey for
the VF in the paravirtualed PKEY table index 0. When this is the case,
the VF IB stack will find in index 0 an invalide pkey, which is all
zeros.
Moreover, the cloud managment can assign the pkey value at index 0 at
any time of the guest life cycle.
The correct behavior for IPoIB to address these requirements for
parent interfaces is to use PKEY_CHANGE event as trigger to optionally
re-init the device pkey value and re-create all the relevant resources
accordingly, if the value of the pkey in index 0 has changed (from
invalid to valid or from valid value X to invalid value Y).
This patch enhances the heavy flushing code which is triggered by pkey
change event, to behave correctly for parent devices. For child
devices, the code remains the same, namely chases pkey value and not
index.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure that the IB invalid pkey (0x0000 or 0x8000) isn't used for
child devices.
Also, make sure to always set the full membership bit for the pkey of
devices created by rtnl link ops.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, QP1 is created using pkey index 0. This patch simply looks
for the index containing the default pkey, rather than hard-coding
pkey index 0.
This change will have no effect in native mode, since QP0 and QP1 are
created before the SM configures the port, so pkey table will still be
the default table defined by the IB Spec, in C10-123: "If non-volatile
storage is not used to hold P_Key Table contents, then if a PM
(Partition Manager) is not present, and prior to PM initialization of
the P_Key Table, the P_Key Table must act as if it contains a single
valid entry, at P_Key_ix = 0, containing the default partition
key. All other entries in the P_Key Table must be invalid."
Thus, in the native mode case, the driver will find the default pkey
at index 0 (so it will be no different than the hard-coding).
However, in SR-IOV mode, for VFs, the pkey table may be
paravirtualized, so that the VF's pkey index zero may not necessarily
be mapped to the real pkey index 0. For VFs, therefore, it is
important to find the virtual index which maps to the real default
pkey.
This commit does the following for QP1 creation:
1. Find the pkey index containing the default pkey, and use that index
if found. ib_find_pkey() returns the index of the
limited-membership default pkey (0x7FFF) if the full-member default
pkey is not in the table.
2. If neither form of the default pkey is found, use pkey index 0
(previous behavior).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In the sq_overhead() function, if qp_typ is equal to IB_QPT_RC, size
will be used uninitialized.
Signed-off-by: Andi Shyti <andi@etezian.org>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We don't set "resp.reserved". Since it's at the end of the struct
that means we don't have to copy it to the user.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When creating tunnel QPs for special QP tunneling, look for the
default pkey in the slave's virtual pkey table. If it is present, use
the real pkey index where the default pkey is located.
If the default pkey is not found in the pkey table, use the real pkey
index which is stored at index 0 in the slave's virtual pkey table
(this is the current behavior).
This change is required to support cloud computing, where the
paravirtualized index of the default pkey is moved to index 1 or
higher. The pkey at paravirtualized index 0 is used for the default
IPoIB interface created by the VF.
Its possible for the pkey value at paravirtualized index 0 to be
invalid (zero) at VF probe time (pkey index 0 is mapped to real pkey
index 127, which contains pkey = 0).
At some point after the VF probe, the cloud computing interface at the
hypervisor maps virtual index 0 for the VF to the pkey index
containing the pkey that IPoIB will use in its operation. However,
when the tunnel QP is created, the pkey at the slave's virtual index 0
is still mapped to the invalid pkey index, so tunnel QP creation
fails.
This commit causes the hypervisor to search for the default pkey in
the slave's pkey table -- and this pkey is present in the table (at
index > 0) at tunnel QP creation time, so that the tunnel QP creation
will succeed.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Calling cma_save_ib_info() for CM SIDR REQs results in a crash
accessing an invalid path record pointer.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If a application is using AF_IB with a UD QP, but does not provide any
private data, we will end up accessing invalid memory. Check for this
case and handle it appropriately.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Building cma.o triggers this gcc warning:
drivers/infiniband/core/cma.c: In function ‘rdma_resolve_addr’:
drivers/infiniband/core/cma.c:465:23: warning: ‘port’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/infiniband/core/cma.c:426:5: note: ‘port’ was declared here
This is a false positive, as "port" will always be initialized if we're
at "found". But if we assign to "id_priv->id.port_num" directly, we can
drop "port". That will, obviously, silence gcc.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit bca1935ccd, which removes variables
nes_tcp_state_str and nes_iwarp_state_str, assuming that they aren't
defined. However, they are defined within a #ifdef NES_DEBUG statement,
which if enabled causes "defined but not used" compiler warning, when
the variables are removed.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 0b3ddf380c ("Log all SDMA errors unconditionally") missed
part of the patch.
This also corrects a format warning when dma_addr_t is 32 bits
on a 64 bit system.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The "uresp.reserved" field isn't initialized on this path so it could
leak uninitialized stack information to the user.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We pass a few bytes of uninitialized stack memory to the user here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A grab bag of places which don't properly initialize stack data. I
removed one place which cleared ".rsvd" because it's not needed now
that I have added a memset() earlier in the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
"uresp.ma_sync_key" doesn't get set on this path so we leak 8 bytes of data.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
I'd like to remove rdma/ib_cache.h some day, so let's avoid
proliferating uses of it unnecessarily.
Signed-off-by: Roland Dreier <roland@purestorage.com>
- AF_IB (native IB addressing) for CMA from Sean Hefty
- New mlx5 driver for Mellanox Connect-IB adapters (including post merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- Resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- Other small changes and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nZh8
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- AF_IB (native IB addressing) for CMA from Sean Hefty
- new mlx5 driver for Mellanox Connect-IB adapters (including post
merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- other small changes and fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
mlx5: Return -EFAULT instead of -EPERM
IB/qib: Log all SDMA errors unconditionally
IB/qib: Fix module-level leak
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
IB/uverbs: Use get_unused_fd_flags(O_CLOEXEC) instead of get_unused_fd()
mlx5_core: Fixes for sparse warnings
IB/mlx5: Make profile[] static in main.c
mlx5: Fix parameter type of health_handler_t
mlx5: Add driver for Mellanox Connect-IB adapters
IB/core: Add reserved values to enums for low-level driver use
IB/srp: Bump driver version and release date
IB/srp: Make HCA completion vector configurable
IB/srp: Maintain a single connection per I_T nexus
IB/srp: Fail I/O fast if target offline
IB/srp: Skip host settle delay
IB/srp: Avoid skipping srp_reset_host() after a transport error
IB/srp: Fix remove_one crash due to resource exhaustion
IB/qib: New transmitter tunning settings for Dell 1.1 backplane
IB/core: Fix error return code in add_port()
...
For copy_to/from_user() failure, the correct error code is -EFAULT not
-EPERM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds code to log SDMA errors for supportability purposes.
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The vzalloc()'ed field physshadow is leaked on module unload.
This patch adds vfree after the sibling page shadow is freed.
Reported-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If the transport layer is offline it is more appropriate to let
srp_abort() return FAST_IO_FAIL instead of SUCCESS.
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity this round on performance improvements in target-core
while benchmarking the prototype scsi-mq initiator code with
vhost-scsi fabric ports, along with a number of iscsi/iser-target
improvements and hardening fixes for exception path cases post v3.10
merge.
The highlights include:
- Make persistent reservations APTPL buffer allocated on-demand, and
drop per t10_reservation buffer. (grover)
- Make virtual LUN=0 a NULLIO device, and skip allocation of NULLIO
device pages (grover)
- Add transport_cmd_check_stop write_pending bit to avoid extra
access of ->t_state_lock is WRITE I/O submission fast-path. (nab)
- Drop unnecessary CMD_T_DEV_ACTIVE check from
transport_lun_remove_cmd to avoid extra access of ->t_state_lock in
release fast-path. (nab)
- Avoid extra t_state_lock access in __target_execute_cmd fast-path
(nab)
- Drop unnecessary vhost-scsi wait_for_tasks=true usage +
->t_state_lock access in release fast-path. (nab)
- Convert vhost-scsi to use modern se_cmd->cmd_kref
TARGET_SCF_ACK_KREF usage (nab)
- Add tracepoints for SCSI commands being processed (roland)
- Refactoring of iscsi-target handling of ISCSI_OP_NOOP +
ISCSI_OP_TEXT to be transport independent (nab)
- Add iscsi-target SendTargets=$IQN support for in-band discovery
(nab)
- Add iser-target support for in-band discovery (nab + Or)
- Add iscsi-target demo-mode TPG authentication context support (nab)
- Fix isert_put_reject payload buffer post (nab)
- Fix iscsit_add_reject* usage for iser (nab)
- Fix iscsit_sequence_cmd reject handling for iser (nab)
- Fix ISCSI_OP_SCSI_TMFUNC handling for iser (nab)
- Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED (nab)
The last five iscsi/iser-target items are CC'ed to stable, as they do
address issues present in v3.10 code. They are certainly larger than
I'd like for stable patch set, but are important to ensure proper
REJECT exception handling in iser-target for 3.10.y"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
iser-target: Ignore non TEXT + LOGOUT opcodes for discovery
target: make queue_tm_rsp() return void
target: remove unused codes from enum tcm_tmrsp_table
iscsi-target: kstrtou* configfs attribute parameter cleanups
iscsi-target: Fix tfc_tpg_auth_cit configfs length overflow
iscsi-target: Fix tfc_tpg_nacl_auth_cit configfs length overflow
iser-target: Add support for ISCSI_OP_TEXT opcode + payload handling
iser-target: Rename sense_buf_[dma,len] to pdu_[dma,len]
iser-target: Add vendor_err debug output
target: Add (obsolete) checking for PMI/LBA fields in READ CAPACITY(10)
target: Return correct sense data for IO past the end of a device
target: Add tracepoints for SCSI commands being processed
iser-target: Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED
iscsi-target: Fix ISCSI_OP_SCSI_TMFUNC handling for iser
iscsi-target: Fix iscsit_sequence_cmd reject handling for iser
iscsi-target: Fix iscsit_add_reject* usage for iser
iser-target: Fix isert_put_reject payload buffer post
iscsi-target: missing kfree() on error path
iscsi-target: Drop left-over iscsi_conn->bad_hdr
target: Make core_scsi3_update_and_write_aptpl return sense_reason_t
...
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
The macro get_unused_fd() is used to allocate a file descriptor with
default flags. Those default flags (0) can be "unsafe": O_CLOEXEC must
be used by default to not leak file descriptor across exec().
Replace calls to get_unused_fd() in uverbs with calls to
get_unused_fd_flags(O_CLOEXEC). Inheriting uverbs fds across exec()
cannot be used to do anything useful.
Based on a patch/suggestion from Yann Droneaud <ydroneaud@opteya.com>.
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver is comprised of two kernel modules: mlx5_ib and mlx5_core.
This partitioning resembles what we have for mlx4, except that mlx5_ib
is the pci device driver and not mlx5_core.
mlx5_core is essentially a library that provides general functionality
that is intended to be used by other Mellanox devices that will be
introduced in the future. mlx5_ib has a similar role as any hardware
device under drivers/infiniband/hw.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
[ Merge in coccinelle fixes from Fengguang Wu <fengguang.wu@intel.com>.
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds a check in isert_rx_opcode() to ignore non TEXT + LOGOUT
opcodes when SessionType=Discovery has been negotiated.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The return value wasn't checked by any of the callers. Assuming this is
correct behaviour, we can simplify some code by not bothering to
generate it.
nab: Add srpt_queue_data_in() + srpt_queue_tm_rsp() nops around
srpt_queue_response() void return
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds isert_handle_text_cmd() to handle incoming
ISCSI_OP_TEXT PDU processing, along with isert_put_text_rsp()
for posting ISCSI_OP_TEXT_RSP ib_send_wr response.
It copies ISCSI_OP_TEXT payload using unsolicited payload at
&iser_rx_desc->data[0] into iscsi_cmd->text_in_ptr for usage
with outgoing isert_put_text_rsp() -> iscsit_build_text_rsp()
v2 changes:
- Let iscsit_build_text_rsp() determine any extra padding
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that these two variables are used for REJECT payloads as well
as SCSI response sense payloads, rename them to something that
makes more sense.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add output for ib_wc.vendor_err in isert_cq_[t,r]x_work(), which
is useful for debugging future issues.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where RDMA_CM_EVENT_DISCONNECTED may occur
before the connection shutdown has been completed by rx/tx threads,
that causes isert_free_conn() to wait indefinately on ->conn_wait.
This patch allows isert_disconnect_work code to invoke rdma_disconnect
when isert_disconnect_work() process context is started by client
session reset before isert_free_conn() code has been reached.
It also adds isert_conn->conn_mutex protection for ->state within
isert_disconnect_work(), isert_cq_comp_err() and isert_free_conn()
code, along with isert_check_state() for wait_event usage.
(v2: Add explicit iscsit_cause_connection_reinstatement call
during isert_disconnect_work() to force conn reset)
Cc: stable@vger.kernel.org # 3.10+
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds target_get_sess_cmd reference counting for
iscsit_handle_task_mgt_cmd(), and adds a target_put_sess_cmd()
for the failure case.
It also fixes a bug where ISCSI_OP_SCSI_TMFUNC type commands
where leaking iscsi_cmd->i_conn_node and eventually triggering
an OOPs during struct isert_conn shutdown.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves ISCSI_OP_REJECT failures into iscsit_sequence_cmd()
in order to avoid external iscsit_reject_cmd() reject usage for all
PDU types.
It also updates PDU specific handlers for traditional iscsi-target
code to not reset the session after posting a ISCSI_OP_REJECT during
setup.
(v2: Fix CMDSN_LOWER_THAN_EXP for ISCSI_OP_SCSI to call
target_put_sess_cmd() after iscsit_sequence_cmd() failure)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_add_reject() + iscsit_add_reject_from_cmd()
usage to not sleep on iscsi_cmd->reject_comp to address a free-after-use
usage bug in v3.10 with iser-target code.
It saves ->reject_reason for use within iscsit_build_reject() so the
correct value for both transport cases. It also drops the legacy
fail_conn parameter usage throughput iscsi-target code and adds
two iscsit_add_reject_cmd() and iscsit_reject_cmd helper functions,
along with various small cleanups.
(v2: Re-enable target_put_sess_cmd() to be called from
iscsit_add_reject_from_cmd() for rejects invoked after
target_get_sess_cmd() has been called)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing isert_put_reject() logic to post
a outgoing payload buffer to hold the 48 bytes of original PDU
header request payload for the rejected cmd.
It also fixes ISTATE_SEND_REJECT handling in isert_response_completion()
-> isert_do_control_comp() code, and drops incorrect iscsi_cmd_t->reject_comp
usage.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some during
this cycle, but even going though my tree isn't a great fit. Ian
Campbell has prototyped splitting the bindings and .dtb files into a
separate repository. The plan is to migrate to using that sometime in
the next few kernel releases which should get rid of a lot of the churn
on binding docs and .dts files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CndB
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some
during this cycle, but even going though my tree isn't a great fit.
Ian Campbell has prototyped splitting the bindings and .dtb files into
a separate repository. The plan is to migrate to using that sometime
in the next few kernel releases which should get rid of a lot of the
churn on binding docs and .dts files"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of: Fix address decoding on Bimini and js2x machines
of: remove CONFIG_OF_DEVICE
usb: chipidea: depend on CONFIG_OF instead of CONFIG_OF_DEVICE
of: remove of_platform_driver
ibmebus: convert of_platform_driver to platform_driver
driver core: move to_platform_driver to platform_device.h
mfd: DT bindings for the palmas family MFD
ARM: dts: omap3-devkit8000: fix NAND memory binding
of/base: fix typos
of: remove #ifdef from linux/of_platform.h
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Calling dev_set_name with a single paramter causes it to be handled as a
format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents,
including wrappers like device_create*() and bdi_register().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several InfiniBand HCAs allow configuring the completion vector per
CQ. This allows spreading the workload created by IB completion
interrupts over multiple MSI-X vectors and hence over multiple CPU
cores. In other words, configuring the completion vector properly not
only allows reducing latency on an initiator connected to multiple
SRP targets but also allows improving throughput.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
An SRP target is required to maintain a single connection between
initiator and target. This means that if the 'add_target' attribute
is used to create a second connection to a target, the first
connection will be logged out and that the SCSI error handler will
kick in. The SCSI error handler will cause the SRP initiator to
reconnect, which will cause I/O over the second connection to fail.
Avoid such ping-pong behavior by disabling relogins.
If reconnecting manually is necessary, that is possible by deleting
and recreating an rport via sysfs.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If reconnecting failed we know that no command completion will
be received anymore. Hence let the SCSI error handler fail such
commands immediately.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The SRP initiator implements host reset by reconnecting to the SRP
target. That means that communication with the target is possible as
soon as host reset finished. Hence skip the host settle delay.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The SCSI error handler assumes that the transport layer is operational
if an eh_abort_handler() returns SUCCESS. Hence srp_abort() only
should return SUCCESS if sending the ABORT TASK task management
function succeeded. This patch avoids the SCSI error handler skipping
the srp_reset_host() call after a transport layer error.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If the add_one callback fails during driver load no resources are
allocated so there isn't a need to release any resources. Trying
to clean the resource may lead to the following kernel panic:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffa0132331>] srp_remove_one+0x31/0x240 [ib_srp]
RIP: 0010:[<ffffffffa0132331>] [<ffffffffa0132331>] srp_remove_one+0x31/0x240 [ib_srp]
Process rmmod (pid: 4562, threadinfo ffff8800dd738000, task ffff8801167e60c0)
Call Trace:
[<ffffffffa024500e>] ib_unregister_client+0x4e/0x120 [ib_core]
[<ffffffffa01361bd>] srp_cleanup_module+0x15/0x71 [ib_srp]
[<ffffffff810ac6a4>] sys_delete_module+0x194/0x260
[<ffffffff8100b0f2>] system_call_fastpath+0x16/0x1b
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Roland Dreier
Erez Shitrit
Or Gerlitz
Jack Morgenstein
Andi Shyti
Dan Carpenter
Wei Yongjun
Sean Hefty
Paul Bolle
Mike Marciniszyn
Linus Torvalds
Dean Luick
Bart Van Assche
Eli Cohen
Nicholas Bellinger
Joern Engel
Kees Cook
Vu Pham
Dotan Barak