MPP44 can be used to differentiate between one-bay (TS-11x) and
two-bay (TS-21x) devices.
According to an engineer from QNAP, the setting of MPP44 depends
on the firmware rather than hardware. Presumably, this means
that you could fake the MPP44 value by changing the boot loader.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add MPP definitions for Marvell Kirkwood 88F6282 revision.
Update some defines to reflect datasheet's MPP names.
Signed-off-by: Benjamin Zores <benjamin.zores@alcatel-lucent.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Among other changes, commit b2a731aa ("D-link DNS-323 revision A1 power
LED") changed the default behaviour of the power LED from solid to
blinking. This was done to match the original DNS-323 firmware which
blinks during the boot process and sets the LED to solid when booting
has completed. However, the downside of this behaviour is that it
requires userland code to change the LED, even for those who don't
care about the behaviour of the original firmware. Therefore, change
it to solid again and let those who care about the original behaviour
change the behaviour from userland.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
On the QNAP TS-41x, MPP45 is used to show the setting of jumper JP1.
Fix the documentation to explain what the settings really indicate.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Export GPIO 45 which is used to indicate the setting of the JP1
jumper. This is useful for userland tools, such as qcontrol, to
see whether the LCD or a serial console is connected.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fix the following warning :
WARNING: vmlinux.o(.text+0x95a0): Section mismatch in reference from the
function qnap_tsx1x_register_flash() to the (unknown reference) .init.data:(unknown)
The function qnap_tsx1x_register_flash() references
the (unknown reference) __initdata (unknown).
This is often because qnap_tsx1x_register_flash lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Add alignment to syscall metadata declarations
perf: Sync callchains with period based hits
perf: Resurrect flat callchains
perf: Version String fix, for fallback if not from git
perf: Version String fix, using kernel version
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: rename causes kernel Oops
GFS2: BUG in gfs2_adjust_quota
GFS2: Fix kernel NULL pointer dereference by dlm_astd
GFS2: recovery stuck on transaction lock
GFS2: O_TRUNC not working on stuffed files across cluster
No need to take address, w90p910_ts is already a pointer.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes a kernel Oops in the GFS2 rename code.
The problem was in the way the gfs2 directory code was trying
to re-use sentinel directory entries.
In the failing case, gfs2's rename function was renaming a
file to another name that had the same non-trivial length.
The file being renamed happened to be the first directory
entry on the leaf block.
First, the rename code (gfs2_rename in ops_inode.c) found the
original directory entry and decided it could do its job by
simply replacing the directory entry with another. Therefore
it determined correctly that no block allocations were needed.
Next, the rename code deleted the old directory entry prior to
replacing it with the new name. Therefore, the soon-to-be
replaced directory entry was temporarily made into a directory
entry "sentinel" or a place holder at the start of a leaf block.
Lastly, it went to re-add the replacement directory entry in
that leaf block. However, when gfs2_dirent_find_space was
looking for space in the leaf block, it used the wrong value
for the sentinel. That threw off its calculations so later
it decides it can't really re-use the sentinel and therefore
must allocate a new leaf block. But because it previously decided
to re-use the directory entry, it didn't waste the time to
grab a new block allocation for the inode. Therefore, the
inode's i_alloc pointer was still NULL and it crashes trying to
reference it.
In the case of sentinel directory entries, the entire dirent is
reused, not just the "free space" portion of it, and therefore
the function gfs2_dirent_find_space should use the value 0
rather than GFS2_DIRENT_SIZE(0) for the actual dirent size.
Fixing this calculation enables the reproducer programs to work
properly.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
HighMem pages on i686 do not get mapped to the buffer_heads and this was
causing a NULL pointer dereference when we were trying to memset page buffers
to zero.
We now use zero_user() that kmaps the page and directly manipulates page data.
This patch also fixes a boundary condition that was incorrect.
Signed-off-by: Abhi Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes a problem in an error path when looking
up dinodes. There are two sister-functions, gfs2_inode_lookup
and gfs2_process_unlinked_inode. Both functions acquire and
hold the i_iopen glock for the dinode being looked up. The last
thing they try to do is hold the i_gl glock for the dinode.
If that glock fails for some reason, the error path was
incorrectly calling gfs2_glock_put for the i_iopen glock twice.
This resulted in the glock being prematurely freed. The
"minimum hold time" usually kept the glock in memory, but the
lock interface to dlm (aka lock_dlm) freed its memory for the
glock. In some circumstances, it would cause dlm's dlm_astd daemon
to try to call the bast function for the freed lock_dlm memory,
which resulted in a NULL pointer dereference.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes bugzilla bug #590878: GFS2: recovery stuck on
transaction lock. We set the frozen flag on the glock when we receive
a completion that cannot be delivered due to blocked locks. At that
point we check to see whether the first waiting holder has the noexp
flag set. If the noexp lock is queued later, then we need to unfreeze
the glock at that point in time, namely, in the glock work function.
This patch was originally written by Steve Whitehouse, but since
he's on holiday, I'm submitting it. It's been well tested with a
complex recovery test called revolver.
Signed-off-by: Steve Whitehouse <swhiteho@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
This patch replaces a statement that got dropped out by accident.
Without the patch, truncates on stuffed (very small) files cause
those files to have an unpredictable size.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/fsl-booke: Fix address issue when using relocatable kernels
powerpc/cpm1: Mark micropatch code/data static and __init
powerpc/cpm1: Fix build with various CONFIG_*_UCODE_PATCH combinations
powerpc/cpm: Reintroduce global spi_pram struct (fixes build issue)
From: Bin Yang <bin.yang@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The commit 83ba9ea8a0 ommitted the return
line for the old synaptics model accidentally. This resulted in a wrong
check, namely, the dimensions are checked for the old devices that don't
support the query properly.
This patch adds the return line back.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
input: i8042 - add runtime check in x86's i8042_platform_init
Revert "Input: fixup X86_MRST selects"
Revert "Input: do not force selecting i8042 on Moorestown"
x86, mrst: Add i8042_detect API for Moorestwon platform
x86: Add i8042 pre-detection hook to x86_platform_ops
x86, platform: Export x86_platform to modules
* 'arm/defconfig/reduced-v2.6.35-rc1' of git://git.pengutronix.de/git/ukl/linux-2.6:
ARM: reduce defconfigs
This is a big change, but results in no loss of information, despite us
losing almost 200k lines:
177 files changed, 652 insertions(+), 194157 deletions(-)
and Grant Likely thinks powerpc can also use the same reduction
technique.
The python script that did the reduction looks like this:
#! /usr/bin/env python
# vim: set fileencoding=utf-8 :
# Copyright (C) 2010 by Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
import re
import subprocess
import os
import sys
# This prevents including a timestamp in the .config which makes comparing a
# bit easier.
os.environ['KCONFIG_NOTIMESTAMP'] = 'Yes, please'
# XXX: get these using getopt
kernel_tree = '' # os.path.join(os.environ['HOME'], 'gsrc', 'linux-2.6')
arch = 'arm'
target = sys.argv[1]
defconfig_src = os.path.join(kernel_tree, 'arch/%s/configs/%s' % (arch, target))
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
origconfig = list(open('.config'))
config = list(origconfig)
config_size = os.stat('.config').st_size
i = 0
while i < len(config):
print 'test for %r' % config[i]
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config[:i])
defconfig.writelines(config[i + 1:])
defconfig.close()
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
if os.stat('.config').st_size == config_size and list(open('.config')) == origconfig:
del config[i]
else:
i += 1
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config)
defconfig.close()
which is pretty self-explanatory.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: uvc: Fix multiple symbols definitions with UVC gadget and host drivers
V4L/DVB: v4l: mem2mem_testdev: fix g_fmt NULL pointer dereference
V4L/DVB: uvcvideo: Power line frequency control doesn't support GET_MIN/MAX/RES
V4L/DVB: ivtv: Add delay to ensure the decoder always restarts with a blank screen
V4L/DVB: Documentation: Add the Philips FQ1236 MK5 to video4linux/CARDLIST.tuner
V4L/DVB: tveeprom: Add an entry for tuner code 168: a TCL M30WTP-4N-E tuner
V4L/DVB: tuner: Add a definition for the Philips FQ1236 MK5 NTSC tuner
V4L/DVB: OMAP_VOUT: fix: Module params were not working through bootargs
V4L/DVB: OMAP_VOUT: fix: Replaced dma-sg with dma-contig
V4L/DVB: OMAP_VOUT:Build FIX: Rebased against latest DSS2 changes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Send Report ID when numbered reports are sent over the control endpoint.
HID: Enable HID_QUIRK_MULTI_INPUT for Retro Adaptor
HID: add support for CH Eclipse yoke
HID: eliminate a double lock in debug code
HID: ntrig: add support for new firwmare versions
HID: check for HID_QUIRK_IGNORE during probing
HID: roccat: fix modules interdependencies
File patterns are one per line.
Fixed include file location.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After remove a rmap, we should flush all vcpu's tlb
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The UVC gadget driver borrowed code from the UVC host driver without
changing the symbol names. This results in a namespace clash with
multiple definitions of several symbols when compiling both drivers in
the kernel.
Make all generic UVC functions and variables static in the UVC gadget
driver, as the symbols are not referenced outside of the gadget driver.
Rename the uvc_trace_param global variable to uvc_gadget_trace_param.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Fix autoloading of fschmd on recent Fujitsu machines
hwmon: (coretemp) Properly label the sensors
hwmon: (coretemp) Skip duplicate CPU entries
hwmon: (it87) Fix in7 on IT8720F
hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c/mips: Fix error return codes from Sibyte i2c bus driver
i2c: Fix probability check
Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: Peter Edwards <samwise@bagshot-row.org>
Acked-by: Paul Qureshi <retro@world3.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: Jonathan Rockway <jon@jrock.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When booting a relocatable kernel it needs to jump to the correct
start address, which for BookE parts is usually unchanged
regardless of the physical memory offset.
Recent changes cause problems with how we calculate the start
address, it was always adding the RMO into the start address
which is incorrect. This patch only adds in the RMO offset
if we are in the kexec code path, as it needs the RMO to work
correctly.
Instead of adding the RMO offset in in the common code path, we
can just set r6 to the RMO offset in the kexec code path instead
of to zero, and finally perform the masking in the common code
path
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This saves runtime memory and fixes lots of sparse warnings like this:
CHECK arch/powerpc/sysdev/micropatch.c
arch/powerpc/sysdev/micropatch.c:27:6: warning: symbol 'patch_2000'
was not declared. Should it be static?
arch/powerpc/sysdev/micropatch.c:146:6: warning: symbol 'patch_2f00'
was not declared. Should it be static?
...
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Warnings are treated as errors for arch/powerpc code, so build fails
with CONFIG_I2C_SPI_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:630: warning: unused variable 'smp'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
And with CONFIG_USB_SOF_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:629: warning: unused variable 'spp'
arch/powerpc/sysdev/micropatch.c:628: warning: unused variable 'iip'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
This patch fixes these issues by introducing proper #ifdefs.
Cc: <stable@kernel.org> [ .33, .34 ]
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
spi_t was removed in commit 644b2a680c
("powerpc/cpm: Remove SPI defines and spi structs"), the commit assumed
that spi_t isn't used anywhere outside of the spi_mpc8xxx driver. But
it appears that the struct is needed for micropatch code. So, let's
reintroduce the struct.
Fixes the following build issue:
CC arch/powerpc/sysdev/micropatch.o
micropatch.c: In function 'cpm_load_patch':
micropatch.c:629: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
micropatch.c:629: error: 'spp' undeclared (first use in this function)
micropatch.c:629: error: (Each undeclared identifier is reported only once
micropatch.c:629: error: for each function it appears in.)
Reported-by: LEROY Christophe <christophe.leroy@c-s.fr>
Reported-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: <stable@kernel.org> [ .33, .34 ]
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CPU: Testing write buffer coherency: ok
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:3145 check_flags+0xcc/0x1dc()
Modules linked in:
[<c0035120>] (unwind_backtrace+0x0/0xf8) from [<c0355374>] (dump_stack+0x20/0x24)
[<c0355374>] (dump_stack+0x20/0x24) from [<c0060c04>] (warn_slowpath_common+0x58/0x70)
[<c0060c04>] (warn_slowpath_common+0x58/0x70) from [<c0060c3c>] (warn_slowpath_null+0x20/0x24)
[<c0060c3c>] (warn_slowpath_null+0x20/0x24) from [<c008f224>] (check_flags+0xcc/0x1dc)
[<c008f224>] (check_flags+0xcc/0x1dc) from [<c00945dc>] (lock_acquire+0x50/0x140)
[<c00945dc>] (lock_acquire+0x50/0x140) from [<c0358434>] (_raw_spin_lock+0x50/0x88)
[<c0358434>] (_raw_spin_lock+0x50/0x88) from [<c00fd114>] (set_task_comm+0x2c/0x60)
[<c00fd114>] (set_task_comm+0x2c/0x60) from [<c007e184>] (kthreadd+0x30/0x108)
[<c007e184>] (kthreadd+0x30/0x108) from [<c0030104>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
possible reason: unannotated irqs-on.
irq event stamp: 3
hardirqs last enabled at (2): [<c0059bb0>] finish_task_switch+0x48/0xb0
hardirqs last disabled at (3): [<c002f0b0>] ret_slow_syscall+0xc/0x1c
softirqs last enabled at (0): [<c005f3e0>] copy_process+0x394/0xe5c
softirqs last disabled at (0): [<(null)>] (null)
Fix this by ensuring that the lockdep interrupt state is manipulated in
the appropriate places. We essentially treat userspace as an entirely
separate environment which isn't relevant to lockdep (lockdep doesn't
monitor userspace.) We don't tell lockdep that IRQs will be enabled
in that environment.
Instead, when creating kernel threads (which is a rare event compared
to entering/leaving userspace) we have to update the lockdep state. Do
this by starting threads with IRQs disabled, and in the kthread helper,
tell lockdep that IRQs are enabled, and enable them.
This provides lockdep with a consistent view of the current IRQ state
in kernel space.
This also revert portions of 0d928b0b61
which didn't fix the problem.
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sibyte i2c bus driver returns non-descriptive error values.
Update to return error values as defined in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new unified probing function differs from the original code, and
the preliminary test whether probing is possible must be updated
accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
For some reason if we declare a static variable and then assign it
later, and the assignment contains a __attribute__((__aligned__(#))),
some versions of gcc will ignore it.
This caused the syscall meta data to not be compact in its section
and caused a kernel oops when the section was being read.
The fix for these versions of gcc seems to be to add the aligned
attribute to the declaration as well.
This fixes the BZ regression:
https://bugzilla.kernel.org/show_bug.cgi?id=16353
Reported-by: Zeev Tarantov <zeev.tarantov@gmail.com>
Tested-by: Zeev Tarantov <zeev.tarantov@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <AANLkTinkKVmB0fpVeqUkMeqe3ZYeXJdI8xDuzJEOjYwh@mail.gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Fujitsu slightly changed the DMI strings in their recent machines,
(for example the D2778) and this breaks the automatic loading of the
needed fschmd driver. Being more tolerant on string comparison fixes
the issue.
This closes bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sergey Spiridonov <sena@hurd.homeunix.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
On hyper-threaded CPUs, each core appears twice in the CPU list. Skip
the second entry to avoid duplicate sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.
It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Cc: stable@kernel.org
Martin Michlmayr
Benjamin Zores
Arnaud Patard
Linus Torvalds
Wan ZongShun
Bob Peterson
Abhijith Das
Nicolas Pitre
Takashi Iwai
Yinghai Lu
Joe Perches
Russell King
Xiao Guangrong
Alan Ott
Laurent Pinchart
Peter Edwards
Jonathan Rockway
Matthew McClintock
Anton Vorontsov
Guenter Roeck
Jean Delvare
Steven Rostedt