Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.
This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...
Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd65
In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.
The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy
powered on is the safest default behavior. Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Several EISA device IDs for 3c509 family network cards are missing from
the driver, making the cards unusable in their EISA mode. Here's a fix to
add them based on the EISA configuration files distributed by 3Com and our
eisa.ids database.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to explicitly mark words 85-87 as valid ones since
firmware doesn't do it.
This should fix support for LBA48 and FLUSH CACHE [EXT] command
which stopped working after we applied more strict checking of
identify words in:
commit 942dcd85bf
("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()")
and
commit 4b58f17d7c
("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()")
Reported-and-tested-by: "Trevor Hemsley" <trevor.hemsley@ntlworld.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
fsldma: Fix compile warnings
fsldma: fix memory leak on error path in fsl_dma_prep_memcpy()
fsldma: snooping is not enabled for last entry in descriptor chain
fsldma: fix infinite loop on multi-descriptor DMA chain completion
fsldma: fix "DMA halt timeout!" errors
fsldma: fix check on potential fdev->chan[] overflow
fsldma: update mailling list address in MAINTAINERS
Gary Lin reports that a new device id needs to be added to the atl1e in
order to get some new Asus hardware to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transmit queue gets full we enable interrupts for TX completions
There was a race that we handled the TX queue both from the interrupt context
and from the transmit function. Using "spin_trylock_irq()" ensures this
doesn't happen.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'
v2: move under DRM_I915 from DRM_I915_KMS
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Commit 4973b22a ("ACPI processor: reset the throttling state once it's
invalid") introduced a new warning which prints a spurious newline.
The ACPI_WARNING macro that is used already takes care of adding a
newline, after adding ACPI_CA_VERSION to the message. Remove the newline
to avoid the message getting split into two lines.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently acpi_video_exit() is exported as well as using __exit which causes:
WARNING: drivers/acpi/video.o(__ksymtab+0x0): Section mismatch in reference from the variable __ksymtab_acpi_video_exit to the function .exit.text:acpi_video_exit()
The symbol acpi_video_exit is exported and annotated __exit
Fix this by removing the __exit annotation of acpi_video_exit or drop the export.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When BIOS SETUP is changed to disable EIST, some BIOS
hand the OS an un-initialized _PSS:
Name (_PSS, Package (0x06)
{
Package (0x06)
{
0x80000000, // frequency [MHz]
0x80000000, // power [mW]
0x80000000, // latency [us]
0x80000000, // BM latency [us]
0x80000000, // control
0x80000000 // status
},
...
These are outrageous values for frequency,
power and latency, raising the question where to draw
the line between legal and illegal. We tend to survive
garbage in the power and latency fields, but we can BUG_ON
when garbage is in the frequency field.
Cpufreq multiplies the frequency by 1000 and stores it in a u32 KHz.
So disregard a _PSS with a frequency so large
that it can't be represented by cpufreq.
https://bugzilla.redhat.com/show_bug.cgi?id=500311
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: Correct Makefile to make isp1760 buildable"
usb-serial: fix crash when sub-driver updates firmware
USB: isp1760: urb_dequeue doesn't always find the urbs
USB: Yet another Conexant Clone to add to cdc-acm.c
USB: atmel_usb_udc: Use kzalloc() to allocate ep structures
USB: atmel-usba-udc : fix control out requests.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: do not oops when driver_unregister() is called for unregistered drivers
sysfs: file.c: use create_singlethread_workqueue()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - better handle bad scheduler decisions
Input: usb1400_ts - fix access to "device data" in resume function
Input: multitouch - augment event semantics documentation
Input: multitouch - add tracking ID to the protocol
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
i915: Set object to gtt domain when faulting it back in
drm/i915: Apply a big hammer to 865 GEM object CPU cache flushing.
drm/i915: Fix tiling pitch handling on 8xx.
If you setserial a port which has never been initialised we change the type
but don't update the I/O method pointers. The same problem is true if you
change the io type of a port - but nobody ever does that so nobody noticed!
Remember the old type and when attaching if the type has changed reload the
port accessor pointers. We can't do it blindly as some 8250 drivers load custom
accessors and we must not stomp those.
Tested-by: Victor Seryodkin <vvscore@gmail.com>
Closes-bug: #13367
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The amd8111_edac.c driver will fail allmodconfig on architectures other
than PPC, introduce Kconfig dependency to avoid this, since both AMD8111
and AMD8131 chips are only adopted on Maple so far.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "bus_id" member in the device structure has been obsolete, use
dev_name() instead.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove wrong fifo size definition for some AT91 products.
Due to a misunderstanding of some AT91 datasheets, a fifo size of 2048
(words) has been introduced by mistake. In fact, all products (AT91/AT32)
are sharing the same fifo size of 512 words.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correctly restore the FrameBuffer register state in the resume function.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/serial/8250_gsc.c:44: warning: format '%lx' expects type
'long unsigned int', but argument 2 has type 'resource_size_t'
[akpm@linux-foundation.org: fix it to handle u64's]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/parport/parport_gsc.c:356: warning: format '%lx' expects type
'long unsigned int', but argument 2 has type 'resource_size_t'
[akpm@linux-foundation.org: fix it to handle u64's]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The check for an overindexing of mpc52xx_uart_{ports,nodes} has an
off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
http://bugzilla.kernel.org/show_bug.cgi?id=13312
at76_dwork_hw_scan holds a mutex while calling ieee80211_scan_completed,
which then calls at76_config which needs the same mutex. This reworks
the ordering to not hold the lock while calling ieee80211_scan_completed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following patch fixes:
- re-initialization of host->col_addr which is used as byte index
between the successive READID flash commands.
- compile error when CONFIG_PM is enabled
- pass on the error code from clk_get()
- return -ENOMEM in case of failed ioremap()
- pass on the return value of platform_driver_probe() directly
- remove excessive printk
- let command line partition table parsing with mxc_nand name.
The cmd_line parsing is done via <mtd-id> name that differs
from mxc_nand by default and looks like "NAND 256MiB 1,8V 8-bit"
Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the build for CONFIG_NET_POLL_CONTROLLER that I broke with
217cbfa856 ("mac8390: fix regression
caused during net_device_ops conversion").
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not call t3_link_fault() under spinlock, as it calls msleep().
Besides, only the access to pi->link_fault needs to be serialized.
Also initialize local variables before checking the link status,
link state fields might otherwise end up containing garbage.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5e68b772e6
cxgb3: map entire Rx page, feed map+offset to Rx ring.
introduced a regression on platforms defining DECLARE_PCI_UNMAP_ADDR()
and related macros as no-ops.
Rx descriptors are fed with the a page buffer bus address + page chunk offset.
The page buffer bus address is set and retrieved through
pci_unamp_addr_set(), pci_unmap_addr().
These functions being meaningless on x86 (if CONFIG_DMA_API_DEBUG is not set).
The HW ends up with a bogus bus address.
This patch saves the page buffer bus address for all plaftorms.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing the i7300_idle driver on i5000-series hardware required
an edit to i7300_idle.h to "#define SUPPORT_I5000 1" and a re-build
of both i7300_idle and ioat_dma.
Replace that build-time scheme with a load-time module parameter:
"7300_idle.forceload=1" to make it easier to test the driver
on hardware that while not officially validated, works fine
and is much more commonly available.
By default (no modparam) the driver will continue to load
only on the i7300.
Note that ioat_dma runs a copy of i7300_idle's probe routine
to know to reserve an IOAT channel for i7300_idle.
This change makes ioat_dma do that always on the i5000,
just like it does on the i7300.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Andrew Henroid <andrew.d.henroid@intel.com>
We also fix a problem with cleaning up properly when initializing
drivers and devices, so checks like this will work successfully.
Portions of the patch by Linus and Greg and Ingo.
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 26e1287594.
A larger patch (f7e7aa585) a few days after this one added the same line
to the Makefile, but in a different place. While it'd be more correct to
revert that one, it's easier to revert this one because this is a
one-liner.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1244) fixes a crash in usb-serial that occurs when a
sub-driver returns a positive value from its attach method, indicating
that new firmware was loaded and the device will disconnect and
reconnect. The usb-serial core then skips the step of registering the
port devices; when the disconnect occurs, the attempt to unregister
the ports fails dramatically.
This problem shows up with Keyspan devices and it might affect others
as well.
When the attach method returns a positive value, the patch sets
num_ports to 0. This tells usb_serial_disconnect() not to try
unregistering any of the ports; instead they are cleaned up by
destroy_serial().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver (and presumably others) allocates several URBs when it
opens and tries to free them when it closes. The isp1760_urb_dequeue
function gets called, but the packet being dequeued is not necessarily at
the
front of one of the 32 queues. If not, the isp1760_urb_done function doesn't
get called for the URB and the process trying to free it hangs forever on a
wait_queue. This patch does two things. If the URB being dequeued has others
queued behind it, it re-queues them. And it searches the queues looking for
the URB being dequeued rather than just looking at the one at the front of
the queue.
[bigeasy@linutronix] whitespace fixes, reformating
Cc: stable <stable@kernel.org>
Signed-off-by: Warren Free <wfree@ipmn.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another quirky Conexant USB Modem Clone to usb cdc-acm.c
Signed-off-by: Xiao Kaijian <xiaokj@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This ensures that all fields are properly initialized.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox
Alan Cox
Linus Torvalds
Neil Horman
Ed Swierk
Mike Frysinger
Maciej W. Rozycki
Bartlomiej Zolnierkiewicz
Greg Kroah-Hartman
Yevgeny Petrilin
David S. Miller
Len Brown
Frans Pop
Jaswinder Singh Rajput
Zhang Rui
Harry Ciao
Nicolas Ferre
Marek Szyprowski
Alexander Beregalov
Roel Kluin
John W. Linville
Vladimir Barinov
Finn Thain
Divy Le Ray
Kay Sievers
Alan Stern
Warren Free
Xiao Kaijian
Haavard Skinnemoen