Optimize the plane register accesses a little bit by grabbing
the uncore lock manually across the entire pile of accesses and
using I915_READ_FW().
This helps keep the pipe update vblank evade critical section
below our 100 usec deadline, particularly with lockdep enabled.
And in general we want to keep that critical section as short
as possible as it's executed with interrupts disabled.
Not all plane updates currently happen from within the vblank evade
critical section, so we must use the irqsave/irqrestore variants
of the spinlock functions in the plane hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-5-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Pull all the plane register writes closer together to avoid having
a lot of unrelated stuff in between them. This will make things more
clear once we'll grab the uncore lock around the entire bunch. Also
in the future we might even consider moving more of the register
value computation out from the plane update hooks. This should make
that easier to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Add a big fat warning in __intel_display_resume that the old state is
invalid, and use the correct state everywhere.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489071125-917-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[mlankhorst: Change one occurence of conn_state to new_conn_state in
verify_connector_state, and drop old_conn_state there]
The trouble here is that looking at all connector->state in the
verifier isn't good, because that's run from the commit work, which
doesn't hold the connection_mutex. Which means we're only allowed to
look at states in our atomic update.
The simple fix for future proofing would be to switch over to
drm_for_each_connector_in_state, but that has the problem that the
verification then fails if not all connectors are in the state. And we
also need to be careful to check both old and new encoders, and not
screw things up when an encoder gets reassigned.
Note that this isn't the full fix, since we still look at
connector->state. To fix that, we need Maarten's patch series to
switch over to state pointers within drm_atomic_state, but that's a
different series.
v2: Use oldnew iterator (Maarten).
v3: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-6-daniel.vetter@ffwll.ch
This gets rid of the last users of for_each_intel_connector(), remove
that too.
At first I wasn't sure whether the 2 loops in the modeset state
checker should instead only loop over the connectors in the atomic
commit. But we never add connectors to an atomic update if they don't
(or won't have) a CRTC assigned, which means there'd be a gap in check
coverage. Hence loop over everything on those too.
v2: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-5-daniel.vetter@ffwll.ch
Drive-by fixup while looking at all the connector_list walkers -
holding connection_mutex does actually _not_ give you locking to look
at the legacy drm_connector->encoder->crtc pointer chain. That one is
solely owned by the atomic commit workers. Instead we must inspect the
atomic state.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-4-daniel.vetter@ffwll.ch
DRM_UT_CORE generates way too much noise usually, so having the
framebuffer init failures use DRM_UT_CORE is a pain when trying to
find out the reason why you failed in creating a framebuffer.
Let's use DRM_UT_KMS for these debug messages instead.
v2: s/at less than/at most/ in the debug message (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-6-ville.syrjala@linux.intel.com
Let's try to keep the alignment requirements in one place, and so
towards that end let's move the AUX_DIST alignment handling into
intel_surf_alignment() alongside the main surface alignment stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-3-ville.syrjala@linux.intel.com
printks are slow so we should not be doing them from the vblank evade
critical section. These could explain why we sometimes seem to
blow past our 100 usec deadline.
The problem has been there ever since commit bfd16b2a23 ("drm/i915:
Make updating pipe without modeset atomic.") but it may not have
been readily visible until commit e1edbd44e2 ("drm/i915: Complain
if we take too long under vblank evasion.") increased our chances
of noticing it.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: bfd16b2a23 ("drm/i915: Make updating pipe without modeset atomic.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307205419.19447-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Backmerge drm-next to get at all the good stuff in drm-misc. We need
that because:
- drm_connector_list_iter conversion for i915 needs the core patches.
- Maarten's patches to use the new atomic state iterators also need
the core patches.
- We need the new link status property to complete the DP retraining
work, merging through 2 branches wasn't a good idea and we had to
partially backtrack.
- Chris needs reservation_object_trylock and we want to roll out
kref_read everywhere.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
To prevent having to preserve the drm_crtc_state as we clear the
intel_crtc_state, only memset our extended state.
Fixes:
drivers/gpu/drm/i915/intel_display.c: In function ‘clear_intel_crtc_state’:
drivers/gpu/drm/i915/intel_display.c:11301:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
v2: Add a comment and BUILD_BUG_ON to explain the memset()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303154644.6709-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This cannot be done reliably during vblank evasasion
since the color management registers are not double buffered.
The original commit that moved it always during vblank evasion was
wrong, so revert it to before vblank evasion again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 20a34e78f0 ("drm/i915: Update color management during vblank evasion.")
Cc: stable@vger.kernel.org # v4.7+
Link: http://patchwork.freedesktop.org/patch/msgid/1488292128-14540-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Add tracepoints for plane programming. The tracepoints will dump
the frame and scanline counters, so this can be used to verify eg. that
the plane gets reprogrammed at the right time with respect to watermark
programming (if we have appropriate tracepoints for that as well).
v2: Rebase due to legacy cursor changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-16-ville.syrjala@linux.intel.com
Clear out the watermark for all disabled planes to 0. This is required
to avoid falsely thinking that the inherited watermarks are bogus in
case the watermark is actually higher than the FIFO size.
v2: s/noninverted/raw/ for consistency with other platforms
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-13-ville.syrjala@linux.intel.com
Now that vlv/chv have more proper wm programming support, let's reduce
the the update_wm_{pre,post} flags to only cover the pre-ilk platforms.
When we finally convert those as well we can drop these flags entirely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-12-ville.syrjala@linux.intel.com
Remove crtc->wm.cxsr_allowed and just rely on crtc_state->disable_cxsr
instead. This was used only by vlv/chv to indicate whether to enable
cxsr in the wm computation. That doesn't really work anymore, and as far
as the optimal watermarks go we'll just consider the number of planes
and the current pipe, and for the intermediate watermarks we'll also
start to consider disable_cxsr which is set appropriately when planes
are being enabled/disabled.
We'll also flip over the crtc_state->wm.need_postvbl_update setup so
that it's the wm code that will set it. Previously the generic code set
it up, and then the wm code cleared it again if it thought it's not
needed after all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-11-ville.syrjala@linux.intel.com
Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.
And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.
The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().
v2: s/noninverted/raw/ for consistency with other platforms
s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com
In a lot of place we wish to know which planes on the crtc are actually
visible, or how many of them there are. Let's start tracking that in a
bitmask in the crtc state.
We already track enabled planes (ie. ones with an fb and crtc specified by
the user) but that's not quite the same thing as enabled planes may
still end up being invisible due to clipping and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-2-ville.syrjala@linux.intel.com
Remove direct usages of intel_crtc->config from the DDI code. Functions
that didn't yet take a pipe_config as an argument were coverted to do
so.
v2: s/pipe_config/const crtc_state/ (Ville)
- take crtc from crtc_state. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-7-ander.conselvan.de.oliveira@intel.com
Pass intel_crtc to functions intel_ddi_enable_transcoder_func(),
intel_ddi_set_pipe_settings() and intel_ddi_set_vc_payload_alloc(),
instead of the generic crtc type. By changing the functions
intel_ddi_get_crtc_encoder() so that it receives an intel_crtc
parameter, there is no need for the drm_crtc in the callers.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-6-ander.conselvan.de.oliveira@intel.com
It is preferred to pass pipe_config to functions instead of accessing
crtc->config directly. Follow suit and pass pipe_config to the fdi link
train functions.
v2: Add const; s/pipe_config/crtc_state/ (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-5-ander.conselvan.de.oliveira@intel.com
Using crtc->config directly is being removed in favor of passing a
pipe_config. Follow the trend and pass pipe_config to pch_enable()
functions.
v2: s/pipe_config/crtc_state/ (Ville)
- constify crtc_state. (Ville)
- take crtc from crtc_state. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-4-ander.conselvan.de.oliveira@intel.com
Currently ILK-BDW explicitly disable LP1+ watermarks from their
.init_clock_gating() hooks. Unfortunately that hook gets called way too
late since by that time we've already initialized all the watermark
state tracking which then gets out of sync with the hardware state.
We may eventually want to consider killing off the explicit LP1+
disable from .init_clock_gating(). In the meantime however, we can
avoid the problem by reordering the init sequence such that
intel_modeset_init_hw()->intel_init_clock_gating() gets called
prior to the hardware state takeover.
I suppose prior to the two stage watermark programming we were
magically saved by something that forced the watermarks to be
reprogrammed fully after .init_clock_gating() got called. But
now that no longer happens.
Note that the diff might look a bit odd as it kills off one
call of intel_update_cdclk(), but that's fine because
intel_modeset_init_hw() does the exact same thing. Previously
we just did it twice.
Actually even this new init sequence is pretty bogus as
.init_clock_gating() really should be called before any gem
hardware init since it can configure various clock gating
workarounds and whatnot that affect the GT side as well. Also
intel_modeset_init() really should get split up into better
defined init stages. Another "fun" detail is that
intel_modeset_gem_init() is where RPS/RC6 gets configured.
Why that is done from the display code is beyond me. I've
decided to leave all this be for now, and just try to fix
the init sequence enough for watermarks to work.
Cc: stable@vger.kernel.org
Cc: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: David Purton <dcpurton@marshwiggle.net>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: David Purton <dcpurton@marshwiggle.net>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96645
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220140443.30891-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to make cursor updates actually safe wrt. watermark programming
we have to clear the legacy_cursor_update flag in the atomic state. That
will cause the regular atomic update path to do the necessary vblank
wait after the plane update if needed, otherwise the vblank wait would
be skipped and we'd feed the optimal watermarks to the hardware before
the plane update has actually happened.
To make the slow vs. fast path determination in
intel_legacy_cursor_update() a little simpler we can ignore the actual
visibility of the plane (which can only get computed once we've already
chosen out path) and instead we simply check whether the fb is being
set or cleared by the user. This means a fully clipped but logically
visible cursor will be considered visible as far as watermark
programming is concerned. We can do that for the cursor since it's a
fixed size plane and the clipped size doesn't play a role in the
watermark computation.
This should fix underruns that can occur when the cursor gets
enable/disabled or the size gets changed. Hopefully it's good enough
that only pure cursor movement and flips go through unthrottled.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Reported-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Fixes: f79f26921e ("drm/i915: Add a cursor hack to allow converting legacy page flip to atomic, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170217150159.11683-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Reintroduce a lock around tiling vs framebuffer creation to prevent
modification of the obj->tiling_and_stride whilst the framebuffer is
being created. Rather than use struct_mutex once again, use the
per-object lock - this will also be required in future to prevent
changing the tiling whilst submitting rendering.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 24dbf51a55 ("drm/i915: struct_mutex is not required for allocating the framebuffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301154128.2841-2-chris@chris-wilson.co.uk
No more direct return -EINVAL as we have to unwind the
obj->framebuffer_references.
Fixes: 24dbf51a55 ("drm/i915: struct_mutex is not required for allocating the framebuffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301154128.2841-1-chris@chris-wilson.co.uk
According to bspec, the DDI IO power domains should be enabled after
enabling the DPLL and mapping it to the DDI. The current order doesn't
seem to create problems with Skylake and Kabylake, but causes enable
timeouts in Geminilake.
v2: Rebase.
- Take power domain references before sanitizing encoders. (Imre)
- Add comment to get_encoder_power_domains() defition. (Ander)
v3: Don't put the domain if called with HSW/BDW's analog encoder. (CI)
v4: Put IO power domain before unmapping DPLL. (Imre)
- Change return type of intel_ddi_get_power_domains() to u64. (Imre)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com> # v1
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141959.5955-1-ander.conselvan.de.oliveira@intel.com
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYoM2fAAoJEHm+PkMAQRiGr9MH/izEAMri7rJ0QMc3ejt+WmD0
8pkZw3+MVn71z6cIEgpzk4QkEWJd5rfhkETCeCp7qQ9V6cDW1FDE9+0OmPjiphDt
nnzKs7t7skEBwH5Mq5xygmIfkv+Z0QGHZ20gfQWY3F56Uxo+ARF88OBHBLKhqx3v
98C7YbMFLKBslKClA78NUEIdx0UfBaRqerlERx0Lfl9aoOrbBS6WI3iuREiylpih
9o7HTrwaGKkU4Kd6NdgJP2EyWPsd1LGalxBBjeDSpm5uokX6ALTdNXDZqcQscHjE
RmTqJTGRdhSThXOpNnvUJvk9L442yuNRrVme/IqLpxMdHPyjaXR3FGSIDb2SfjY=
=VMy8
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc8' into drm-next
Linux 4.10-rc8
Backmerge Linus rc8 to fix some conflicts, but also
to avoid pulling it in via a fixes pull from someone.
Setting retire=true is identical to using origin=ORIGIN_CS, so make the
same simplification to intel_fb_obj_flush() as already employed for
intel_fb_obj_invalidate().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-6-chris@chris-wilson.co.uk
Flushing the cachelines for an object is slow, can be as much as 100ms
for a large framebuffer. We currently do this under the struct_mutex BKL
on execution or on pageflip. But now with the ability to add fences to
obj->resv for both flips and execbuf (and we naturally wait on the fence
before CPU access), we can move the clflush operation to a workqueue and
signal a fence for completion, thereby doing the work asynchronously and
not blocking the driver or its clients.
v2: Introduce i915_gem_clflush.h and use a new name, split out some
extras into separate patches.
Suggested-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-5-chris@chris-wilson.co.uk
We have three different paths by which userspace wants to flush the
display plane (i.e. objects with obj->pin_display). Use a common helper
to identify those paths and to simplify a later change.
v2: Include the conditional in the name, i915_gem_object_flush_if_display
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-3-chris@chris-wilson.co.uk
Verify that the refcount of all power wells match their HW enabled
state at the end of modeset HW state readout.
Also add documentation on how the reference count for each power well is
supposed to be acquired during initialization and HW state readout.
Suggested by Ander.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487345986-26511-6-git-send-email-imre.deak@intel.com
We do not need the BKL struct_mutex in order to allocate a GEM object,
nor to create the framebuffer, so resist the temptation to take the BKL
willy nilly. As this changes the locking contract around internal API
calls, the patch is a little larger than a plain removal of a pair of
mutex_lock/unlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215105919.7347-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We do not need to hold struct_mutex for destroying drm_i915_gem_objects
any longer, and with a little care taken over tracking
obj->framebuffer_references, we can relinquish BKL locking around the
destroy of intel_framebuffer.
v2: Use atomic check for WARN_ON framebuffer miscounting
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170216094621.3426-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Once upon a time before we had automated GPU state capture upon hangs,
we had intel_gpu_dump. Now we come almost full circle and reinstate that
view of the current GPU queues and registers by using the error capture
facility to snapshot the GPU state when debugfs/.../i915_gpu_info is
opened - which should provided useful debugging to both the error
capture routines (without having to cause a hang and avoid the error
state being eaten by igt) and generally.
v2: Rename drm_i915_error_state to i915_gpu_state to alleviate some name
collisions between the error state dump and inspecting the gpu state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214164611.11381-1-chris@chris-wilson.co.uk
Add for_each_(old)(new)_(plane,connector,crtc)_in_state iterators to
replace the old for_each_xxx_in_state ones. This is useful for >1 flip
depth and getting rid of all xxx->state dereferences.
This requires extra fixups done when committing a state after
duplicating, which in general isn't valid but is used by suspend/resume.
To handle these, introduce drm_atomic_helper_commit_duplicated_state
which performs those fixups before checking & committing the state.
Changes since v1:
- Remove nonblock parameter for commit_duplicated_state.
Changes since v2:
- Use commit_duplicated_state for i915 load detection.
- Add WARN_ON(old_state != obj->state) before swapping.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1484559464-27107-2-git-send-email-maarten.lankhorst@linux.intel.com
This removes the usage of intel_ring_emit in favour of
directly writing to the ring buffer.
intel_ring_emit was preventing the compiler for optimising
fetch and increment of the current ring buffer pointer and
therefore generating very verbose code for every write.
It had no useful purpose since all ringbuffer operations
are started and ended with intel_ring_begin and
intel_ring_advance respectively, with no bail out in the
middle possible, so it is fine to increment the tail in
intel_ring_begin and let the code manage the pointer
itself.
Useless instruction removal amounts to approximately
two and half kilobytes of saved text on my build.
Not sure if this has any measurable performance
implications but executing a ton of useless instructions
on fast paths cannot be good.
v2:
* Change return from intel_ring_begin to error pointer by
popular demand.
* Move tail increment to intel_ring_advance to enable some
error checking.
v3:
* Move tail advance back into intel_ring_begin.
* Rebase and tidy.
v4:
* Complete rebase after a few months since v3.
v5:
* Remove unecessary cast and fix !debug compile. (Chris Wilson)
v6:
* Make intel_ring_offset take request as well.
* Fix recording of request postfix plus a sprinkle of asserts.
(Chris Wilson)
v7:
* Use intel_ring_offset to get the postfix. (Chris Wilson)
* Convert GVT code as well.
v8:
* Rename *out++ to *cs++.
v9:
* Fix GVT out to cs conversion in GVT.
v10:
* Rebase for new intel_ring_begin in selftests.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214113242.29241-1-tvrtko.ursulin@linux.intel.com
I screwed up the rebase of commit d8fc70b736 ("drm/i915: Make power
domain masks 64 bit long") before sending v2, causing a couple of
conversions from 32 to 64 bit masks to be lost.
Fixes: d8fc70b736 ("drm/i915: Make power domain masks 64 bit long")
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170213145733.8779-1-ander.conselvan.de.oliveira@intel.com
Ville Syrjälä
Maarten Lankhorst
Daniel Vetter
Dave Airlie
Chris Wilson
Ander Conselvan de Oliveira
Imre Deak
Tvrtko Ursulin