This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.
When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.
This function aborts them with DID_SOFT_ERROR.
If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.
The result is that disk returning QUEUE FULL causes request failures.
The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags. The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags. The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sym53c8xx_slave_destroy unconditionally assumes that sym53c8xx_slave_alloc has
succesesfully allocated a sym_lcb. This can lead to a NULL pointer dereference
(exposed by commit 4e6c82b).
Signed-off-by: Stratos Psomadakis <psomas@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GCC warns about empty printf format strings, and after
the addition of %pV these existing such cases in the
scsi driver layer were exposed enough for the compiler
to start seeing them.
Based almost entirely upon a patch by Joe Perches.
[jejb: fix up sym53c8xx msg]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To avoid a collision with the newly-added kernel-wide skip_spaces().
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes a huge difference when you have a serial console on bootup to limit
these messages to a sane number.
Signed-off-by: John Stoffel <john@stoffel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make the sym53c8xx_2 driver slave_alloc/destroy less unsafe. References
to the destroyed LCB are cleared from the target structure (instead of
leaving a dangling pointer), and when the last LCB for the target is
destroyed the reference to the upper layer target data is cleared. The
host lock is used to prevent a race with the interrupt handler. Also
user commands are prevented for targets with all LCBs destroyed.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(Resent with proper formatting)
Fix for the sym53c8xx_2 driver to initialize lun's to_clear flag after
a bus reset (a failed clear can trigger a bus reset and it should not
be attemped again after that).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym53c8xx prints a negotiation message after every check condition.
This can add up to a lot of messages for removable-medium devices
(CD-ROM, tape drives, etc.) that are being polled, since they return
check condition when no medium is present. This patch suppresses the
negotiation message if it would be the same as the last one printed.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym53c8xx uses a command queue depth of 2 for untagged devices,
without good reason. This _mostly_ seems to work ok, but it has
caused me some subtle problems. For example, I have an application
where one thread sends write commands to a tape drive, and another
thread sends log sense polling commands. With a queue depth of
2, the polling commands end up being starved for long periods of
time while multiple write commands are serviced (this may also be
related to the fact the the sg driver queues commands in LIFO order).
This problem is fixed by changing the queue depth to 1 for untagged
devices. I have tested this change extensively with many different
tape drives, medium changers, and disk drives (disk drives of course
use tagged commands and are therefore unaffected by this patch).
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym_init_device() doesn't check if pci_iomap() fails. It also tries
to map device RAM without first checking FE_RAM.
1) Move some initialization from sym_init_device() to the top of
sym2_probe().
2) Rename sym_init_device() to sym_iomap_device().
3) Call sym_iomap_device() after sym_check_supported() instead of
before so that device->chip.features will be set.
4) Check FE_RAM in sym_iomap_device() before mapping RAM.
5) If sym_iomap_device() cannot map registers, then abort.
6) If sym_iomap_device() cannot map RAM, then fall back to not using
RAM and continue.
7) Remove the check for FE_RAM in sym_attach() since dev->ram_base
is now always set correctly.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During sym2_probe(), sym_init_device() does pci_iomap(), but there is
no corresponding pci_iounmap() if an error occurs before sym_attach()
copies sym_device::s.{ioaddr,ramaddr} to np.
1) Add the sym_iounmap_device() function.
2) Call sym_iounmap_device() if an error occurs between
sym_init_device() and the time sym_attach() allocates np.
3) Make sym_attach() copy sym_device::s.{ioaddr,ramaddr} to np before
calling any function that can fail so that sym_free_resources()
will do the unmap instead of sym_iounmap_device().
Also fixed by this patch:
During sym2_probe(), if sym_check_raid() returns nonzero, then
pci_release_regions() is never called.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If sym_attach() gets an error at or before request_irq(), then
sym_free_resources() will call free_irq() for an unregistered
interrupt handler.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If sym_attach() fails to allocate np, the error path will dereference
a NULL pointer for printk.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes two bugs:
1) rmmod sym53c8xx uses shost after freeing it with
scsi_put_host(shost).
2) insmod sym53c8xx doesn't call scsi_put_host(shost) if
scsi_add_host() fails, causing a memory leak on the error path.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(The patch updated based on testing and comments from Tony Battersby.)
Change the sym53c8xx_2 driver negotiation logic so that the driver will
tolerate better device removals. Negotiation message(s) will be sent
with every INQUIRY and REQUEST SENSE command, and whenever there is a
change in goals or when the device reports check condition.
The patch was made specifically to address the case where you hotswap
the disk using remove-single-device/add-single-device commands through
/proc/scsi/scsi. Without the patch the driver keeps using old transfer
parameters even though the target is reset and reports check condition,
so the data transfer of the very first INQUIRY will fail.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch frees the luntbl dma area in sym_hcb_free if allocated.
Since the luntbl is part of a larger dma coherent area not freeing the
luntbl kept a 64k dma coherent area previous allocated through
dma_alloc_coherent allocated. This prevented a DLPAR remove IO
operation from completing successfully.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The sym53c8xx driver, for some reason, seems to mostly re-implement
linux/list.h with added bogosity. The main one is it's implementation
of sym_que_entry which spits warnings with recent gcc's on some
64 bits architectures.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/aic7xxx/aic7770_osm.c:53:58: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:355:47: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:372:55: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:997:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1003:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1165:46: warning: Using plain integer as NULL pointer
drivers/scsi/fdomain.c:1446:40: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:1650:51: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:3171:42: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:5732:52: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8189:31: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8225:34: warning: Using plain integer as NULL pointer
drivers/scsi/dpt_i2o.c:156:32: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:954:42: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:1104:18: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the calculation of the data transfer residual for the
case of a command that is supposed to transfer an odd number of bytes on
a wide bus but transfers nothing instead.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes two bugs pointed by James Bottomley:
1. the if (!sym_data->io_reset). That variable is only ever filled
by a stack based completion. If we find it non empty it means
this code has been entered twice and we have a severe problem,
so that should just become a BUG_ON(sym_data->io_reset).
2. sym_data->io_reset should be set to NULL before the routine is
exited otherwise the PCI recovery code could end up completing
what will be a bogus pointer into the stack.
Big thanks to James Bottomley for help with the patch.
Signed-off-by: Krzysztof Helt <krzysztof.h1@w.pl>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The patch described by the following excerpt from ChangeLog-2.6.24-rc1
eventually causes a "irq X: nobody cared" error after a while:
commit 99c9e0a1d6
Author: Matthew Wilcox <matthew@wil.cx>
Date: Fri Oct 5 15:55:12 2007 -0400
[SCSI] sym53c8xx: Make interrupt handler capable of returning IRQ_NONE
After this happens, the kernel disables the IRQ, causing the SCSI card
to stop working until the next reboot. The problem is caused by the
interrupt handler returning IRQ_NONE instead of IRQ_HANDLED after
handling an interrupt-on-the-fly (INTF) condition. The following patch
fixes the problem.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The following commit changed the pointer passed to request_irq(), but
failed to change the pointer passed to free_irq():
commit 99c9e0a1d6
Author: Matthew Wilcox <matthew@wil.cx>
Date: Fri Oct 5 15:55:12 2007 -0400
[SCSI] sym53c8xx: Make interrupt handler capable of returning IRQ_NONE
...
The result is that free_irq() doesn't actually take any action. This
patch fixes it.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This function just printed a message to the user; move the print to its
only caller, and turn it into an starget_printk.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This structure is accessed by the device; the fewer Linux things in it,
the better. Using the pci_dev pointer from the hostdata requires a lot
of changes:
- Pass Scsi_Host to a lot of routines which currently take a sym_hcb.
- Set the Scsi_Host as the pci drvdata (instead of the sym_hcb)
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make sym_interrupt return an irqreturn_t instead of void, and take a
Scsi_Host instead of a sym_hcb. Pass the Scsi_Host to the interrupt
handler instead of the sym_hcb. Rename the host_data to sym_data.
Keep a pci_dev pointer in the sym_data. Rename the Scsi_Host from
instance to shost.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These macros aren't needed any more. They used to be used for SPARC.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we have a scsi_cmnd, it gives the user more information than the
sym_name, and maybe the target.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
By introducing the use_dac(), set_dac() and DMA_DAC_MASK macros, we can
eliminate a lot of ifdefs from the code. We now rely on the compiler to
optimise away a few things that we'd formerly relied on the preprocessor
to do. This makes sym_setup_bus_dma_mask() small enough to inline into
its only caller.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With sysfs making these options tunable at runtime, there's no
justification for keeping this horrendously complex specification
string around.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These struct elements record info that is never needed
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mikulas Patocka
Yinghai Lu
Maxime Jayat
Al Viro
Greg Kroah-Hartman
Stephen Hemminger
Stratos Psomadakis
Lucas De Marchi
Jiri Kosina
Jeff Garzik
Uwe Kleine-König
David Miller
Andrew Morton
André Goddard Rosa
John Stoffel
Aaro Koskinen
Yang Hongyang
Harvey Harrison
Tony Battersby
Jens Axboe
Mike Anderson
Benjamin Herrenschmidt
James Bottomley
Nathan Lynch
FUJITA Tomonori
Krzysztof Helt
Randy Dunlap
Linus Torvalds
Matthew Wilcox