Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other callers of udp_tunnel6_xmit_skb just pass 0 for the prio
argument. Jesse Gross <jesse@nicira.com> suggested that prio is really
the same as IPv4's tos and should be handled the same, so this is my
interpretation of that suggestion.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NOTE: Link-local IPv6 addresses for remote endpoints are not supported,
since the driver currently has no capacity for binding a geneve
interface to a specific link.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is primarily for consistancy with vxlan and other tunnels which
use network byte order for similar parameters.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Partially due to a pre-exising "thinko", the new metadata-based tx/rx
paths were handling ECN propagation differently than the traditional
tx/rx paths. This patch removes the "thinko" (involving multiple
ip_hdr assignments) on the rx path and corrects the ECN handling on
both the rx and tx paths.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code handling vlan tag insertion was dropped in commit 371bd1061d
("geneve: Consolidate Geneve functionality in single module."). Now we
need to drop the related vlan feature bits in the netdev structure.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tun-info options pointer is used in few cases to
pass options around. But tunnel options can be accessed using
ip_tunnel_info_opts() API without using the pointer. Following
patch removes the redundant pointer and consistently make use
of API.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geneve can benefit from GRO at the device level in a manner similar
to other tunnels, especially as hardware offloads are still emerging.
After this patch, aggregated frames are seen on the tunnel interface.
Single stream throughput nearly doubles in ideal circumstances (on
old hardware).
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change simplifies Geneve Tunnel hash table management.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_core module handles send and receive functionality.
This way OVS could use the Geneve API. Now with use of
tunnel meatadata mode OVS can directly use Geneve netdevice.
So there is no need for separate module for Geneve. Following
patch consolidates Geneve protocol processing in single module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch create new tunnel flag which enable
tunnel metadata collection on given device. These devices
can be used by tunnel metadata based routing or by OVS.
Geneve Consolidation patch get rid of collect_md_tun to
simplify tunnel lookup further.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink interface to configure Geneve UDP port number.
So that user can configure it for a Gevene device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On packet transmit path geneve need to lookup route. Following
patch improves route lookup using more parameters.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an initial implementation of a netdev driver for GENEVE
tunnels. This implementation uses a fixed UDP port, and only supports
point-to-point links with specific partner endpoints. Only IPv4
links are supported at this time.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville
Pravin B Shelar
Jesse Gross
Jiri Benc
Phil Sutter