Move the gory details of kmap & al into a private header and only document
the interfaces which are usable by drivers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20201103095858.827582066@linutronix.de
For some obscure reason when CONFIG_DEBUG_HIGHMEM is enabled the stack
depth is increased from 20 to 41. But the only thing DEBUG_HIGHMEM does is
to enable a few BUG_ON()'s in the mapping code.
That's a leftover from the historical mapping code which had fixed entries
for various purposes. DEBUG_HIGHMEM inserted guard mappings between the map
types. But that got all ditched when kmap_atomic() switched to a stack
based map management. Though the WITH_KM_FENCE magic survived without being
functional. All the thing does today is to increase the stack depth.
Add a working implementation to the generic kmap_local* implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20201103095857.268258322@linutronix.de
The kmap_atomic* interfaces in all architectures are pretty much the same
except for post map operations (flush) and pre- and post unmap operations.
Provide a generic variant for that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20201103095857.175939340@linutronix.de
The #endif at the end of the file matches up with the '#if
defined(HASHED_PAGE_VIRTUAL)' on line 374. Not the CONFIG_HIGHMEM #if
earlier.
Fix comments on both of the #endif's to indicate the correct end of
blocks for each.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lkml.kernel.org/r/20200819184635.112579-1-ira.weiny@intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Untangle the somewhat incestous way of how VMALLOC_START is used all across the
kernel, but is, on x86, defined deep inside one of the lowest level page table headers.
It doesn't help that vmalloc.h only includes a single asm header:
#include <asm/page.h> /* pgprot_t */
So there was no existing cross-arch way to decouple address layout
definitions from page.h details. I used this:
#ifndef VMALLOC_START
# include <asm/vmalloc.h>
#endif
This way every architecture that wants to simplify page.h can do so.
- Also on x86 we had a couple of LDT related inline functions that used
the late-stage address space layout positions - but these could be
uninlined without real trouble - the end result is cleaner this way as
well.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mm@kvack.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
totalram_pages and totalhigh_pages are made static inline function.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/1542090790-21750-4-git-send-email-arunks@codeaurora.org
Signed-off-by: Arun KS <arunks@codeaurora.org>
Suggested-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nr_free_highpages() manually adds statistics per each highmem zone and
returns a total value for them. Whenever we add a new highmem zone, we
need to consider this function and it's really troublesome. Make it
handle all highmem zones by itself.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
User-visible effect:
Architectures that choose this method of maintaining cache coherency
(MIPS and xtensa currently) are able to use high memory on cores with
aliasing data cache. Without this fix such architectures can not use
high memory (in case of xtensa it means that at most 128 MBytes of
physical memory is available).
The problem:
VIPT cache with way size larger than MMU page size may suffer from
aliasing problem: a single physical address accessed via different
virtual addresses may end up in multiple locations in the cache.
Virtual mappings of a physical address that always get cached in
different cache locations are said to have different colors. L1 caching
hardware usually doesn't handle this situation leaving it up to
software. Software must avoid this situation as it leads to data
corruption.
What can be done:
One way to handle this is to flush and invalidate data cache every time
page mapping changes color. The other way is to always map physical
page at a virtual address with the same color. Low memory pages already
have this property. Giving architecture a way to control color of high
memory page mapping allows reusing of existing low memory cache alias
handling code.
How this is done with this patch:
Provide hooks that allow architectures with aliasing cache to align
mapping address of high pages according to their color. Such
architectures may enforce similar coloring of low- and high-memory page
mappings and reuse existing cache management functions to support
highmem.
This code is based on the implementation of similar feature for MIPS by
Leonid Yegoshin.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Marc Gauthier <marc@cadence.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Steven Hill <Steven.Hill@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Latinoware 2012.
There's a slightly non-trivial merge in virtio-net, as we cleaned up the
virtio add_buf interface while DaveM accepted the mq virtio-net patches.
You can see my solution in my pending-rebases branch, if that helps, but I
know you love merging:
https://git.kernel.org/?p=linux/kernel/git/rusty/linux.git;a=commit;h=12e4e64fa66a4c812e4855de32abdb4d819526fe
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=myDR
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio update from Rusty Russell:
"Some nice cleanups, and even a patch my wife did as a "live" demo for
Latinoware 2012.
There's a slightly non-trivial merge in virtio-net, as we cleaned up
the virtio add_buf interface while DaveM accepted the mq virtio-net
patches."
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (27 commits)
virtio_console: Add support for remoteproc serial
virtio_console: Merge struct buffer_token into struct port_buffer
virtio: add drv_to_virtio to make code clearly
virtio: use dev_to_virtio wrapper in virtio
virtio-mmio: Fix irq parsing in command line parameter
virtio_console: Free buffers from out-queue upon close
virtio: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
virtio_console: Use kmalloc instead of kzalloc
virtio_console: Free buffer if splice fails
virtio: tools: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: scsi: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: rpmsg: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: net: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: console: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: make virtqueue_add_buf() returning 0 on success, not capacity.
virtio: console: don't rely on virtqueue_add_buf() returning capacity.
virtio_net: don't rely on virtqueue_add_buf() returning capacity.
virtio-net: remove unused skb_vnet_hdr->num_sg field
virtio-net: correct capacity math on ring full
virtio: move queue_index and num_free fields into core struct virtqueue.
...
In flush_all_zero_pkmaps(), we have an index of the pkmap associated with
the page. Using this index, we can simply get virtual address of the
page. So change it.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can find free page_address_map instance without the page_address_pool.
So remove it.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pool_lock protects the page_address_pool from concurrent access. But,
access to the page_address_pool is already protected by kmap_lock. So
remove it.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Minchan Kin <minchan@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To calculate an index of pkmap, using PKMAP_NR() is more understandable
and maintainable, so change it.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmap_to_page returns the corresponding struct page for a virtual address
of an arbitrary mapping. This works by checking whether the address
falls in the pkmap region and using the pkmap page tables instead of the
linear mapping if appropriate.
Unfortunately, the bounds checking means that PKMAP_ADDR(LAST_PKMAP) is
incorrectly treated as a highmem address and we can end up walking off
the end of pkmap_page_table and subsequently passing junk to pte_page.
This patch fixes the bound check to stay within the pkmap tables.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some virtio device drivers (9p) need to translate high virtual addresses
to physical addresses, which are inserted into the virtqueue for
processing by userspace.
This patch exports the kmap_to_page symbol, so that the affected drivers
can be compiled as modules.
Cc: stable@kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The patch "mm: add support for a filesystem to activate swap files and use
direct_IO for writing swap pages" added support for using direct_IO to
write swap pages but it is insufficient for highmem pages.
To support highmem pages, this patch kmaps() the page before calling the
direct_IO() handler. As direct_IO deals with virtual addresses an
additional helper is necessary for get_kernel_pages() to lookup the struct
page for a kmap virtual address.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Paris <eparis@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
The files changed within are only using the EXPORT_SYMBOL
macro variants. They are not using core modular infrastructure
and hence don't need module.h but only the export.h header.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Followup to 33dd4e0ec9 "mm: make some struct page's const" which missed the
HASHED_PAGE_VIRTUAL case.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears i386 uses kmap_atomic infrastructure regardless of
CONFIG_HIGHMEM which results in a compile error when highmem is disabled.
Cure this by providing the needed few bits for both CONFIG_HIGHMEM and
CONFIG_X86_32.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep the current interface but ignore the KM_type and use a stack based
approach.
The advantage is that we get rid of crappy code like:
#define __KM_PTE \
(in_nmi() ? KM_NMI_PTE : \
in_irq() ? KM_IRQ_PTE : \
KM_PTE0)
and in general can stop worrying about what context we're in and what kmap
slots might be appropriate for that.
The downside is that FRV kmap_atomic() gets more expensive.
For now we use a CPP trick suggested by Andrew:
#define kmap_atomic(page, args...) __kmap_atomic(page)
to avoid having to touch all kmap_atomic() users in a single patch.
[ not compiled on:
- mn10300: the arch doesn't actually build with highmem to begin with ]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix up drivers/gpu/drm/i915/intel_overlay.c]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kdb kmap should never get used outside of the kernel debugger
exception context.
Signed-off-by: Jason Wessel<jason.wessel@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Ingo Molnar <mingo@elte.hu>
CC: linux-mm@kvack.org
In f4112de6b6 ("mm: introduce
debug_kmap_atomic") I said that debug_kmap_atomic() needs
CONFIG_TRACE_IRQFLAGS_SUPPORT.
It was wrong. (I thought irqs_disabled() is only available when the
architecture has CONFIG_TRACE_IRQFLAGS_SUPPORT)
Remove the #ifdef CONFIG_TRACE_IRQFLAGS_SUPPORT check to enable
kmap_atomic() debugging for the architectures which do not have
CONFIG_TRACE_IRQFLAGS_SUPPORT.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
debug_kmap_atomic() tries to prevent ever printing more than 10
warnings, but it does so by testing whether an unsigned integer
is equal to 0. However, if the warning is caused by a nested
IRQ, then this counter may underflow and the stream of warnings
will never end.
Fix that by using a signed integer instead.
Signed-off-by: Soeren Sandmann Pedersen <sandmann@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: a.p.zijlstra@chello.nl
Cc: <stable@kernel.org> # .31.x
LKML-Reference: <ye8zl7b8ktj.fsf@camel23.daimi.au.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When porting blktrace to tracepoints, we changed to trace/block.h
for trace prober declarations.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
x86 has debug_kmap_atomic_prot() which is error checking function for
kmap_atomic. It is usefull for the other architectures, although it needs
CONFIG_TRACE_IRQFLAGS_SUPPORT.
This patch exposes it to the other architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Highmem code can leave ptes and tlb entries around for a given page even after
kunmap, and after it has been freed.
>From what I can gather, the PAT code may change the cache attributes of
arbitrary physical addresses (ie. including highmem pages), which would result
in aliases in the case that it operates on one of these lazy tlb highmem
pages.
Flushing kmaps should solve the problem.
I've also just added code for conditional flushing if we haven't got
any dangling highmem aliases -- this should help performance if we
change page attributes frequently or systems that aren't using much
highmem pages (eg. if < 4G RAM). Should be turned into 2 patches, but
just for RFC...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hash et al. sizing code in SCTP wants to make the
calculation totalram_pages - totalhigh_pages, just
like TCP. But this requires an export for the
CONFIG_HIGHMEM case to work.
Signed-off-by: David S. Miller <davem@davemloft.net>
fastcall is always defined to be empty, remove it
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE
that is only usable by allocations that specify both __GFP_HIGHMEM and
__GFP_MOVABLE. This has the effect of keeping all non-movable pages within a
single memory partition while allowing movable allocations to be satisfied
from either partition. The patches may be applied with the list-based
anti-fragmentation patches that groups pages together based on mobility.
The size of the zone is determined by a kernelcore= parameter specified at
boot-time. This specifies how much memory is usable by non-movable
allocations and the remainder is used for ZONE_MOVABLE. Any range of pages
within ZONE_MOVABLE can be released by migrating the pages or by reclaiming.
When selecting a zone to take pages from for ZONE_MOVABLE, there are two
things to consider. First, only memory from the highest populated zone is
used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM
but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second,
the amount of memory usable by the kernel will be spread evenly throughout
NUMA nodes where possible. If the nodes are not of equal size, the amount of
memory usable by the kernel on some nodes may be greater than others.
By default, the zone is not as useful for hugetlb allocations because they are
pinned and non-migratable (currently at least). A sysctl is provided that
allows huge pages to be allocated from that zone. This means that the huge
page pool can be resized to the size of ZONE_MOVABLE during the lifetime of
the system assuming that pages are not mlocked. Despite huge pages being
non-movable, we do not introduce additional external fragmentation of note as
huge pages are always the largest contiguous block we care about.
Credit goes to Andy Whitcroft for catching a large variety of problems during
review of the patches.
This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable
by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added
memory continues to be placed in their existing destination as there is no
mechanism to redirect them to a specific zone.
[y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code]
[akpm@linux-foundation.org: various fixes]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xen and VMI both have special requirements when mapping a highmem pte
page into the kernel address space. These can be dealt with by adding
a new kmap_atomic_pte() function for mapping highptes, and hooking it
into the paravirt_ops infrastructure.
Xen specifically wants to map the pte page RO, so this patch exposes a
helper function, kmap_atomic_prot, which maps the page with the
specified page protections.
This also adds a kmap_flush_unused() function to clear out the cached
kmap mappings. Xen needs this to clear out any potential stray RW
mappings of pages which will become part of a pagetable.
[ Zach - vmi.c will need some attention after this patch. It wasn't
immediately obvious to me what needs to be done. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
This is again simplifies some of the VM counter calculations through the use
of the ZVC consolidated counters.
[michal.k.k.piotrowski@gmail.com: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the bounce buffer code from mm/highmem.c to mm/bounce.c so that it can be
more easily disabled when the block layer is disabled.
!!!NOTE!!! There may be a bug in this code: Should init_emergency_pool() be
contingent on CONFIG_HIGHMEM?
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move totalhigh_pages and nr_free_highpages() into highmem.c/.h
Move the totalhigh_pages definition into highmem.c/.h. Move the
nr_free_highpages function into highmem.c
[yoichi_yuasa@tripeaks.co.jp: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_bounce to a per zone counter
nr_bounce is only used for proc output. So it could be left as an event
counter. However, the event counters may not be accurate and nr_bounce is
categorizing types of pages in a zone. So we really need this to also be a
per zone counter.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Convert two mempool users that currently use their own mempool-backed page
allocators to use the generic mempool page allocator.
Also included are 2 trivial whitespace fixes.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch for counting the number of pages for bounce buffers. It's
shown in /proc/vmstat.
Currently, the number of bounce pages are not counted anywhere. So, if
there are many bounce pages, it seems that there are leaked pages. And
it's difficult for a user to imagine the usage of bounce pages. So, it's
meaningful to show # of bouce pages.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thomas Gleixner
Ira Weiny
Ingo Molnar
Arun KS
Greg Kroah-Hartman
Joonsoo Kim
Max Filippov
Linus Torvalds
Joonsoo Kim
Will Deacon
Mel Gorman
Li Haifeng
Paul Gortmaker
Ian Campbell
Peter Zijlstra
Jason Wessel
Akinobu Mita
Uwe Kleine-König
Soeren Sandmann
Li Zefan
Nicolas Pitre
Nick Piggin
David S. Miller
Randy Dunlap
Harvey Harrison
Mel Gorman
Jeremy Fitzhardinge
Christoph Lameter
David Howells
Eric Sesterhenn
Matthew Dobson
Jens Axboe
Al Viro
Al Viro
KAMEZAWA Hiroyuki