* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32, leon: bugfix in LEON SMP interrupt init
sparc32, sun4m: bugfix in SMP IPI traphandler
sparc: Remove unnecessary semicolons
Add support for allocating irqs for bootbus devices
Do not skip interrupt sources in sun4d interrupt handler and acknowledge interrupts correctly
Restructure sun4d_build_device_irq so that timer interrupts can be allocated
sparc: PCIC_PCI needs SPARC32 dependency
sparc: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
sparc32,leon: add GRPCI2 PCI Host driver
sparc32,leon: added LEON-common low-level PCI routines
sparc32: added CONFIG_PCIC_PCI Kconfig setting
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: iio: max517: Fix iio_info changes
Staging: mei: fix debug code
Staging: cx23885: fix include of altera.h
staging: iio: error case memory leak fix
staging: ath6kl: Fix a kernel panic during suspend/resume
staging: gma500: get control from firmware framebuffer if conflicts
staging: gma500: Skip bogus LVDS VBT mode and check for LVDS before adding backlight
staging: usbip: bugfix prevent driver unbind
staging: iio: industrialio-trigger: set iio_poll_func private_data
staging: rts_pstor: use bitwise operator instead of logical one
staging: fix ath6kl build when CFG80211 is not enabled
staging: brcm80211: fix for 'multiple definition of wl_msg_level' build err
staging: fix olpc_dcon build, needs BACKLIGHT_CLASS_DEVICE
Staging: remove STAGING_EXCLUDE_BUILD option
Staging: altera: move .h file to proper place
* 'stable/xen-swiotlb.bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb-2.6:
swiotlb: Export swioltb_nr_tbl and utilize it as appropiate.
struct iio_info introduced a bug where the second channel of a MAX518 can't be
used. This commit fixes the typo (using max518 instead of the max517 struct).
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has higher precedence than !=. H_RDY is 8 and since neither 0 nor
1 are equal to 8 the original condition was always true.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
int i is only needed if CONFIG_ACPI is set
so move it within a new ifdef so kernels without ACPI
don't allocate space for nothing. Fixes warning too.
Signed-off-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
[v2: Fixed warning when CONFIG_ACPI was defined]
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
The patch moves rtc driver for PKUnity-v3 SoC from arch/unicore32/kernel/
to drivers/rtc/, with renaming it to rtc-puv3.c.
Also, Kconfig, Makefile, and MAINTAINERS are modified correspondingly.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
MAINTAINERS: add a maintainer to Gadget Framework
USB: serial: add another 4N-GALAXY.DE PID to ftdi_sio driver
Revert "USB: option: add ID for ZTE MF 330"
drivers/usb/host/ohci-pxa27x.c: add missing clk_put
USB: CONFIG_USB_GADGET_DUALSPEED is not user-configurable
USB: dummy-hcd needs the has_tt flag
usb-storage: redo incorrect reads
usb/renesas_usbhs: free uep on removal
usb/s3c-hsudc: fix error path
usb/pxa25x_udc: cleanup the LUBBOCK err path
usb/mv_udc_core: fix compile
usb: gadget: include <linux/prefetch.h> to fix compiling error
USB: s3c-hsotg: Tone down debugging
usb: remove bad dput after dentry_unhash
USB: core: Tolerate protocol stall during hub and port status read
musb: fix prefetch build failure
USB: cdc-acm: Adding second ACM channel support for Nokia E7 and C7
usb-gadget: unlock data->lock mutex on error path in ep_write()
USB: option Add blacklist for ZTE K3765-Z (19d2:2002)
option: add Prolink PH300 modem IDs
...
One new offender detected by the recently increased type checking in
platform_get_drvdata():
drivers/rtc/rtc-m41t93.c: In function ‘m41t93_remove’:
drivers/rtc/rtc-m41t93.c:192: warning: passing argument 1 of ‘platform_get_drvdata’ from incompatible pointer type
Use spi_get_drvdata() instead of platform_get_drvdata(), cfr. commit
42fea15d6d ("spi/rtc-{ds1390,ds3234,m41t94}:
Use spi_get_drvdata() for SPI devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: off by one errors in multicalls.c
xen: use the trigger info we already have to choose the irq handler
The cx23885 driver was including staging/altera.h, but that file has
moved back into the driver directory.
Why a non-staging driver was including a staging driver is beyond me,
but this fixes the build so everything is happy for now.
For the record, it's not ok for a non-staging driver to depend on a
staging one, as that implies that the non-staging one should also be in
the staging tree if that's needed.
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] soc_camera: preserve const attribute
[media] uvc_entity: initialize return value
[media] media: Fix media device minor registration
[media] Make nchg variable signed because the code compares this variable against negative values
[media] omap3isp: fix compiler warning
[media] v4l: Fix media_entity_to_video_device macro argument name
[media] ivtv: Internally separate encoder & decoder standard setting
[media] ivtvfb: Add sanity check to ivtvfb_pan_display()
[media] ivtvfb: use display information in info not in var for panning
[media] ivtv: Make two ivtv_msleep_timeout calls uninterruptable
[media] anysee: return EOPNOTSUPP for unsupported I2C messages
[media] gspca - ov519: Set the default frame rate to 15 fps
[media] gspca - stv06xx: Set a lower default value of gain for hdcs sensors
[media] gspca: Remove coarse_expo_autogain.h
[media] gspca - ov519: Change the ovfx2 bulk transfer size
[media] gspca - ov519: Fix a regression for ovfx2 webcams
* 'drm-radeon-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: disable hdmi audio by default
drm/radeon/kms: fix for radeon on systems >4GB without hardware iommu
drm/radeon/kms: set family for use in parser.
The flush_to_ldisc() work entry has special logic to notice when it has
seen the original tail of the data queue, and it avoids continuing the
flush if it sees that _original_ tail rather than the current tail.
This logic can trigger in case somebody is constantly adding new data to
the tty while the flushing is active - and the intent is to avoid
excessive CPU usage while flushing the tty, especially as we used to do
this from a softirq context which made it non-preemptible.
However, since we no longer re-arm the work-queue from within itself
(because that causes other trouble: see commit a5660b41af "tty: fix
endless work loop when the buffer fills up"), this just leads to
possible hung tty's (most easily seen in SMP and with a test-program
that floods a pty with data - nobody seems to have reported this for any
real-life situation yet).
And since the workqueue isn't done from timers and softirq's any more,
it's doubtful whether the CPU useage issue is really relevant any more.
So just remove the logic entirely, and see if anybody ever notices.
Alternatively, we might want to re-introduce the "re-arm the work" for
just this case, but then we'd have to re-introduce the delayed work
model or some explicit timer, which really doesn't seem worth it for
this.
Reported-and-tested-by: Guillaume Chazarain <guichaz@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On my x86_64 system with >4GB of ram and swiotlb instead of
a hardware iommu (because I have a VIA chipset), the call
to pci_set_dma_mask (see below) with 40bits returns an error.
But it seems that the radeon driver is designed to have
need_dma32 = true exactly if pci_set_dma_mask is called
with 32 bits and false if it is called with 40 bits.
I have read somewhere that the default are 32 bits. So if the
call fails I suppose that need_dma32 should be set to true.
And indeed the patch fixes the problem I have had before
and which I had described here:
http://choon.net/forum/read.php?21,106131,115940
Acked-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Wierdly the kms parser never initialised the family, it wasn't really used
much, but the fmt checker patch started using it and it fell over.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv40: fall back to paged dma object for the moment
drm/nouveau: fix leak of gart mm node
drm/nouveau: fix vram page mapping when crossing page table boundaries
drm/nv17-nv40: Fix modesetting failure when pitch == 4096px (fdo bug 35901).
drm/nouveau: don't create accel engine objects when noaccel=1
drm/nvc0: recognise 0xdX chipsets as NV_C0
drm/i915: Add a no lvds quirk for the Asus EeeBox PC EB1007
drm/i915: Share the common force-audio property between connectors
drm/i915: Remove unused enum "chip_family"
drm/915: fix relaxed tiling on gen2: tile height
drm/i915/crt: Explicitly return false if connected to a digital monitor
drm/i915: Replace ironlake_compute_wm0 with g4x_compute_wm0
drm/i915: Only print out the actual number of fences for i915_error_state
drm/i915: s/addr & ~PAGE_MASK/offset_in_page(addr)/
drm: i915: correct return status in intel_hdmi_mode_valid()
drm/i915: fix regression after clock gating init split
drm/i915: fix if statement in ivybridge irq handler
* 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/atom: fix PHY init
drm/radeon/kms: add missing Evergreen texture formats to the CS parser
drm/radeon/kms: viewport height has to be even
drm/radeon/kms: remove duplicate reg from r600 safe regs
drm/radeon/kms: add support for Llano Fusion APUs
drm/radeon/kms: add llano pci ids
drm/radeon/kms: fill in asic struct for llano
drm/radeon/kms: add family ids for llano APUs
drm/radeon: fix oops in ttm reserve when pageflipping (v2)
drm/radeon/kms: clean up the radeon kms Kconfig
drm/radeon/kms: fix thermal sensor reading on juniper
drm/radeon/kms: add missing case for cayman thermal sensor
drm/radeon/kms: add blit support for cayman (v2)
drm/radeon/kms/blit: workaround some hw issues on evergreen+
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (21 commits)
ARM: OMAP4: MMC: increase delay for pbias
arm: omap2plus: move NAND_BLOCK_SIZE out of boards
omap4: hwmod: Enable the keypad
omap3: Free Beagle rev gpios when they are read, so others can read them later
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
omap: rx51: Don't power up speaker amplifier at bootup
omap: rx51: Set regulator V28_A always on
ARM: OMAP4: MMC: no regulator off during probe for eMMC
arm: omap2plus: fix ads7846 pendown gpio request
ARM: OMAP2: Add missing iounmap in omap4430_phy_init
ARM: omap4: Pass core and wakeup mux tables to omap4_mux_init
ARM: omap2+: mux: Allow board mux settings to be NULL
OMAP4: fix return value of omap4_l3_init
OMAP: iovmm: fix SW flags passed by user
arch/arm/mach-omap1/dma.c: Invert calls to platform_device_put and platform_device_del
OMAP2+: mux: fix compilation warnings
OMAP: SRAM: Fix warning: format '%08lx' expects type 'long unsigned int'
arm: omap3: cm-t3517: fix section mismatch warning
OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
ARM: OMAP2: Add missing include of linux/gpio.h
...
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
vfs: make unlink() and rmdir() return ENOENT in preference to EROFS
lmLogOpen() broken failure exit
usb: remove bad dput after dentry_unhash
more conservative S_NOSEC handling
This reverts commit a559d2c8c1.
Turns out that device id 0x1d6b:0x0002 is a USB hub, which causes havoc
when the option driver tries to bind to it.
So revert this as it doesn't seem to be needed at all.
Thanks to Michael Tokarev and Paweł Drobek for working on resolving this
issue.
Cc: Paweł Drobek <pawel.drobek@gmail.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The loops over connection ID strings in pm_runtime_clk_notify()
should actually iterate over the strings and not over the elements
of the first of them, so make them behave as appropriate.
This fixes a regression introduced by commit 600b776eb3
(OMAP1 / PM: Use generic clock manipulation routines for runtime PM).
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If CONFIG_PM is not set, init_iommu_pm_ops() introduced by commit
134fac3f45 (PCI / Intel IOMMU: Use
syscore_ops instead of sysdev class and sysdev) is not defined
appropriately. Fix this issue.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The data pointer should be freed in the error
cases of adis16400_trigger_handler().
Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many Linux distributions would enable vesafb in order to display
early stage boot splash. In this case, we will get garbled X
Window screen if running X fbdev on psbfb.
This is because fb0 is occupied by vesafb while psbfb is on fb1.
They tried to drive the same pieces of hardware at the same
time. With unmodified X start-up, it would try to use default
fb0 framebuffer device and unfortunately it is now broken
becaues fb1 supersedes it.
We should let psbfb takeover framebuffer control from vesafb
to get around this problem.
See also commit : 4410f39109
Signed-off-by: Michael Chang <mchang@novell.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the Fit-PC2 the VBT reports an invalid fixed panel mode for LVDS, this gets
in the way for SDVO. This patch makes VBT parsing skip the invalid mode. When
there is no LVDS output the backlight support crashes so the patch also checks
for this before enabling it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implemented pre_reset and post_reset methods of the driver to prevent the
driver from being unbound upon a device reset. Because of this also the
asynchronous reset introduced to prevent a race condition is no longer necessary
(and sometimes causes problems, because it comes later then expected).
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: usbip-devel <usbip-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Failure to set iio_poll_func private_data, causes zero pointer access
violations in all consumer trigger handlers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like a typo.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build errors when CONFIG_CFG80211 is not enabled:
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b71): undefined reference to `cfg80211_scan_done'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b86): undefined reference to `wiphy_unregister'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b8d): undefined reference to `wiphy_free'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18add7): undefined reference to `wiphy_new'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18ae48): undefined reference to `wiphy_register'
drivers/built-in.o: In function `ar6k_cfg80211_tkip_micerr_event':
(.text+0x18ae95): undefined reference to `cfg80211_michael_mic_failure'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afb5): undefined reference to `__ieee80211_get_channel'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afd2): undefined reference to `cfg80211_inform_bss_frame'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b046): undefined reference to `cfg80211_ibss_joined'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b176): undefined reference to `cfg80211_connect_result'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b190): undefined reference to `cfg80211_disconnected'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b291): undefined reference to `cfg80211_get_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b457): undefined reference to `cfg80211_put_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b4fa): undefined reference to `cfg80211_roamed'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix olpc_dcon.c build by selecting the needed kconfig symbol
BACKLIGHT_CLASS_DEVICE.
olpc_dcon.c:(.text+0x11588b): undefined reference to `backlight_device_register'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Part of the requirement to be in the staging tree is that the code must
build, so let's make it easier for people to build the code to
test/prove this out.
Based on a recommendation from Linus to implement this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Staging drivers should be self-contained, without files in the include/
directories. So move the altera.h file back to the driver directory for
now, until it moves out of the staging tree.
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a label before the call to clk_put and jump to that in the error
handling code that occurs after the call to clk_get has succeeded.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1468) changes the Kconfig definition for
USB_GADGET_DUALSPEED. This option is determined entirely by which
device controller drivers are to be built, through Select statements;
it does not need to be (and should not be) configurable by the user.
Also, the "default n" line is superfluous -- everything defaults to N.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like with other host controllers capable of operating at both high
speed and full speed, we need to indicate that the emulated controller
presented by dummy-hcd has this ability. Otherwise usbcore will not
accept full-speed gadgets under dummy-hcd. This patch (as1469) sets
the appropriate has_tt flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds
Roland Stigge
Dan Carpenter
Connor Hansen
Guan Xuetao
Greg Kroah-Hartman
Steffen Sledz
Geert Uytterhoeven
Grant Likely
Alex Deucher
Daniel Haid
Dave Airlie
Rafael J. Wysocki
H Hartley Sweeten
Andre Bartke
Vasanthakumar Thiagarajan
Michael Chang
Patrik Jakobsson
Arjan Mels
Michael Hennerich
Nicolas Kaiser
Randy Dunlap
Roland Vossen
Thomas Abraham
Julia Lawall
Alan Stern