Not every regulator driver should implement set_voltage_sel callback.
See commit e8eef82
"regulator: Provide a selector based set_voltage_sel() operation".
For rc5t583, the regulator voltage can be mapped onto selector values with a
simple calculation, thus implement set_voltage is better than set_voltage_sel.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixing build issue reported by Paul Gortmaker:
It appears this breaks linux-next allmodconfig build, because it
uses an uppercase V in the v2 of its MODULE_LICENSE.
FATAL: modpost: GPL-incompatible module rc5t583-regulator.ko uses
GPL-only symbol 'platform_driver_unregister'
make[2]: *** [__modpost] Error 1
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simplify RC5T583_REG macro by removing _vout_reg and _ds_reg parameters.
The naming for vout_reg and deepsleep_reg can be replaced by:
.vout_reg = RC5T583_REG_##_id##DAC,
.deepsleep_reg = RC5T583_REG_##_id##DAC_DS,
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The nsteps can be calculated by (_max_mv - _min_mv) * 1000 / _step_uV + 1,
thus we can remove _nsteps from RC5T583_REG macro, and then remove
nsteps from struct rc5t583_regulator_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The valid selector should be 0 ... nsteps-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
1. regulator_register returns ERR_PTR on error, thus use IS_ERR to check the
return value.
2. Fix off-by-one for unregistering the registered regulator.
Current code does not unregister regs[0].rdev in clean_exit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The RC5T583 PMIC from RICOH consists of 4 DCDC and 10
LDOs. This driver supports the control of different
regulator output through regulator interface.
This driver depends on MFD driver of RC5T583 and uses
mfd rc5t583 apis to communicate to device for accessing
different device's registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drivers should be able to declare their descriptors const and the framework
shouldn't ever be modifying the desciptor. Make the parameter and the
pointer in regulator_dev const to enforce this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unusual to see a regulator driver not using subsys_initcall() but the
deferred probe support should make this viable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core already announces constraints and we're not adding any new
information such as the chip revision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core already logs the regulator constraints as it is registered and
we're not adding any extra content about the device such as the chip
revision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unusual to see a regulator driver not using subsys_initcall() but with
the probe deferral support should be becoming more and more viable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator core supports this to allow the configuration to be inspected
at runtime even if no software mangement is enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
There's some other allocations but they're not so trivial as they use
kmemdup() and kstrdup().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert mc13892_sw_regulator_ops and mc13xxx_regulator_ops to set_voltage_sel.
mc13xxx_get_best_voltage_index function is not used now, remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adding flag on fixed regulator board configuration structure
to specify whether gpio is open drain type or not.
Passing this information to gpio library when requesting
gpio so that gpio driver can set the pin state accordingly,
for open drain type:
- Pin can be set HIGH as setting as input, PULL UP on
pin make this as HIGH.
- Pin can be set LOW as setting it as output and drive to LOW.
The non-open drain pin can be set HIGH/LOW by setting it to
output and driving it to HIGH/LOW.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet[1], tps62360 is register compatible with tps62362.
tps62361B is register compatible with tps62363.
Thus this patch adds support for tps62362 and tps62363.
[1] http://www.ti.com/litv/pdf/slvsau9b
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The n_voltages are the same for all regulators: (max - min / step) + 1 == 64.
The vol_shift is always 0, and the vol_nbits is always the same as n_voltages
setting. Thus we can remove vol_shitf and vol_nbits fields from struct
max8925_regulator_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code implements max8925_list_voltage but does not set the list_voltage
callback function in max8925_regulator_[ldo|sdv]_ops. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Then we can remove the vol_nbits field from struct pm8607_regulator_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Jett Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code implements pm8607_list_voltage but does not set the list_voltage
callback function in pm8607_regulator_ops. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Jett Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Integer division may truncate the result.
Current code shows changing current is 0mA when selector is 1 ... 8.
For example:
selector = 1
ad5398_calc_current returns 117, debug message shows 117/1000 = 0mA
selector = 2
ad5398_calc_current returns 234, debug message shows 234/1000 = 0mA
selector = 3
ad5398_calc_current returns 351, debug message shows 351/1000 = 0mA
............
selector = 8
ad5398_calc_current returns 937, debug message shows 937/1000 = 0mA
Show the changing current in uA makes it easier for debugging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The client field of struct tps_pmic is not used after converting to regmap API.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The client field of struct tps62360_chip is not used after converting to regmap.
The name field of struct tps62360_chip is not used in this driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In current implementation, da9052_ldo_ops and da9052_ldo5_6_ops are very
similar, only the set_voltage is slightly different.
da9052_buckperi_ops and da9052_dcdc_ops are also similar.
This patch adds da9052_regulator_set_voltage for the set_voltage callback
used by all LDOs and DCDCs. Rework da9052_get_regulator_voltage_sel and
da9052_set_dcdc_voltage to make it possible to be shared by all DCDCs.
Rework da9052_list_voltage to make it to be shared by all DCDCs and LDOs.
Then we can remove da9052_ldo5_6_ops and da9052_buckperi_ops.
We can also remove DA9052_LDO5_6 and DA9052_BUCKPERI macros which is not used
now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown
Axel Lin
Laxman Dewangan