Update the sun4i-ss driver to use the skcipher API instead of the old
ablkcipher one. It's a bit more tricky than s/ablkcipher/skcipher/, but
still nothing special and the driver's logic stays the same.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cosmetic clean up if conditional checks on 0s values.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The variable i is always checked against unsigned value and cannot be
negative.
This patch set it as unsigned.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current sun4i-ss driver could generate data corruption when ciphering/deciphering.
It occurs randomly on end of handled data.
No root cause have been found and the only way to remove it is to replace
all spin_lock_bh by their irq counterparts.
Fixes: 6298e94821 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
gcc correctly warns that the printk output contains a variable that
it thinks is not initialized in some cases:
drivers/crypto/sunxi-ss/sun4i-ss-cipher.c: In function 'sun4i_ss_cipher_poll':
drivers/crypto/sunxi-ss/sun4i-ss-cipher.c:254:76: warning: 'todo' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/crypto/sunxi-ss/sun4i-ss-cipher.c:144:15: note: 'todo' was declared here
A closer look at the function reveals that the variable is always
initialized at this point (ileft is guaranteed to be positive at the
start), but its contents are not well-defined:
Depending on some other variables, it might be either a count in
words or bytes, and it could refer to either input or output.
The easiest solution apparently is to remove the confusing output
and let the reader figure out the state from the other variables.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sun4i_ss_opti_poll function cipher data until the output miter have
a length of 0.
If the crypto API client, give more SGs than necessary this could result
in an infinite loop.
Fix it by checking for remaining bytes, just like sun4i_ss_cipher_poll().
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the Security System included in Allwinner SoC A20.
The Security System is a hardware cryptographic accelerator that support:
- MD5 and SHA1 hash algorithms
- AES block cipher in CBC/ECB mode with 128/196/256bits keys.
- DES and 3DES block cipher in CBC/ECB mode
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Antoine Ténart
Corentin LABBE
Arnd Bergmann