Граф коммитов

9 Коммитов

Автор SHA1 Сообщение Дата
Florian Fainelli 1c99dac8bf MIPS: RB532: Cleanup cpu-features-overrides
Remove commented out definitions.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-17 11:06:26 +01:00
Phil Sutter d9bdffd210 Input: add driver for S1 button of rb532
Mikrotik's Routerboard 532 has two builtin buttons, from which one
triggers a hardware reset. The other one is accessible through GPIO
pin 1. Sadly, this pin is being multiplexed with UART0 input, so
enabling it as interrupt source (as implied by the gpio-keys driver)
is not possible unless UART0 has been turned off. The later one though
is a rather bad idea as the Routerboard is an embedded device with
only a single serial port, so it's almost always used as serial
console device.

This patch adds a driver based on INPUT_POLLDEV, which disables the
UART and reconfigures GPIO pin 1 temporarily while reading the button
state.  This procedure works fine and has been tested as part of
another, unpublished driver for this device.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-09 20:10:12 -07:00
Phil Sutter 0fc6bc0d6e MIPS: RB532: Export rb532_gpio_set_func()
This kernel symbol provides a way for drivers to switch on alternate
function for a certain GPIO pin. Turning it off is done implicitly when
changing the GPIO direction, as that would be fixed when using the given
pin als alternate function.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:01 +00:00
Phil Sutter 3828ee047d MIPS: RB532: Update headers
Remove the {set,get}_434_reg() prototypes, as the functions have been
removed. Also move the prototypes for {get,set}_latch_u5() to the correct
place.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:01 +00:00
Phil Sutter 4aa0f4d726 MIPS: RB532: Add set_type() function to IRQ struct.
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.

The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.

As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)

To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().

After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:32:59 +00:00
Phil Sutter 2e373952cc MIPS: RB532: Provide functions for gpio configuration
As gpiolib doesn't support pin multiplexing, it provides no way to
access the GPIOFUNC register. Also there is no support for setting
interrupt status and level. These functions provide access to them and
are needed by the CompactFlash driver.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-11-20 19:42:33 +00:00
Florian Fainelli 1b432840d0 MIPS: RB532: GPIO register offsets are relative to GPIOBASE
This patch fixes the wrong use of GPIO register offsets
in devices.c. To avoid further problems, use gpio_get_value
to return the NAND status instead of our own expanded code.

Also define the zero offset of the alternate function register to allow
consistent access.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-11-20 19:42:32 +00:00
Florian Fainelli 9609e74093 MIPS: RB532: provide GPIO_BUILTIN_NR and irq_to_gpio/gpio_to_irq
This patchs defines the number of built-in the GPIOs present
on the SoC as Documentation/gpio.txt recommends to do.
Define irq_to_gpio/gpio_to_irq to return the right values so that
it fixes a compilation error on drivers/gpio/gpiolib.c
when enabling debugfs.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:57 +01:00
Ralf Baechle 384740dc49 MIPS: Move headfiles to new location below arch/mips/include
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:52 +01:00