and wireguard.
Current release - regressions:
- smc: keep smc_close_final()'s error code during active close
Current release - new code bugs:
- iwlwifi: various static checker fixes (int overflow, leaks, missing
error codes)
- rtw89: fix size of firmware header before transfer, avoid crash
- mt76: fix timestamp check in tx_status; fix pktid leak;
- mscc: ocelot: fix missing unlock on error in ocelot_hwstamp_set()
Previous releases - regressions:
- smc: fix list corruption in smc_lgr_cleanup_early
- ipv4: convert fib_num_tclassid_users to atomic_t
Previous releases - always broken:
- tls: fix authentication failure in CCM mode
- vrf: reset IPCB/IP6CB when processing outbound pkts, prevent
incorrect processing
- dsa: mv88e6xxx: fixes for various device errata
- rds: correct socket tunable error in rds_tcp_tune()
- ipv6: fix memory leak in fib6_rule_suppress
- wireguard: reset peer src endpoint when netns exits
- wireguard: improve resilience to DoS around incoming handshakes
- tcp: fix page frag corruption on page fault which involves TCP
- mpls: fix missing attributes in delete notifications
- mt7915: fix NULL pointer dereference with ad-hoc mode
Misc:
- rt2x00: be more lenient about EPROTO errors during start
- mlx4_en: update reported link modes for 1/10G
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=r0Jh
-----END PGP SIGNATURE-----
Merge tag 'net-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, and wireguard.
Mostly scattered driver changes this week, with one big clump in
mv88e6xxx. Nothing of note, really.
Current release - regressions:
- smc: keep smc_close_final()'s error code during active close
Current release - new code bugs:
- iwlwifi: various static checker fixes (int overflow, leaks, missing
error codes)
- rtw89: fix size of firmware header before transfer, avoid crash
- mt76: fix timestamp check in tx_status; fix pktid leak;
- mscc: ocelot: fix missing unlock on error in ocelot_hwstamp_set()
Previous releases - regressions:
- smc: fix list corruption in smc_lgr_cleanup_early
- ipv4: convert fib_num_tclassid_users to atomic_t
Previous releases - always broken:
- tls: fix authentication failure in CCM mode
- vrf: reset IPCB/IP6CB when processing outbound pkts, prevent
incorrect processing
- dsa: mv88e6xxx: fixes for various device errata
- rds: correct socket tunable error in rds_tcp_tune()
- ipv6: fix memory leak in fib6_rule_suppress
- wireguard: reset peer src endpoint when netns exits
- wireguard: improve resilience to DoS around incoming handshakes
- tcp: fix page frag corruption on page fault which involves TCP
- mpls: fix missing attributes in delete notifications
- mt7915: fix NULL pointer dereference with ad-hoc mode
Misc:
- rt2x00: be more lenient about EPROTO errors during start
- mlx4_en: update reported link modes for 1/10G"
* tag 'net-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
net: dsa: b53: Add SPI ID table
gro: Fix inconsistent indenting
selftests: net: Correct case name
net/rds: correct socket tunable error in rds_tcp_tune()
mctp: Don't let RTM_DELROUTE delete local routes
net/smc: Keep smc_close_final rc during active close
ibmvnic: drop bad optimization in reuse_tx_pools()
ibmvnic: drop bad optimization in reuse_rx_pools()
net/smc: fix wrong list_del in smc_lgr_cleanup_early
Fix Comment of ETH_P_802_3_MIN
ethernet: aquantia: Try MAC address from device tree
ipv4: convert fib_num_tclassid_users to atomic_t
net: avoid uninit-value from tcp_conn_request
net: annotate data-races on txq->xmit_lock_owner
octeontx2-af: Fix a memleak bug in rvu_mbox_init()
net/mlx4_en: Fix an use-after-free bug in mlx4_en_try_alloc_resources()
vrf: Reset IPCB/IP6CB when processing outbound pkts in vrf dev xmit
net: qlogic: qlcnic: Fix a NULL pointer dereference in qlcnic_83xx_add_rings()
net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed
net: dsa: mv88e6xxx: Fix inband AN for 2500base-x on 88E6393X family
...
Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to decide whether or not reuse existing rx/tx pools
we tried to allow a range of values for the pool parameters rather
than exact matches. This was intended to reuse the resources for
instance when switching between two VIO servers with different
default parameters.
But this optimization is incomplete and breaks when we try to
change the number of queues for instance. The optimization needs
to be updated, so drop it for now and simplify the code.
Fixes: bbd809305b ("ibmvnic: Reuse tx pools when possible")
Reported-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to decide whether or not reuse existing rx/tx pools
we tried to allow a range of values for the pool parameters rather
than exact matches. This was intended to reuse the resources for
instance when switching between two VIO servers with different
default parameters.
But this optimization is incomplete and breaks when we try to
change the number of queues for instance. The optimization needs
to be updated, so drop it for now and simplify the code.
Fixes: 489de956e7 ("ibmvnic: Reuse rx pools when possible")
Reported-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apple M1 Mac minis (2020) with 10GE NICs do not have MAC address in the
card, but instead need to obtain MAC addresses from the device tree. In
this case the hardware will report an invalid MAC.
Currently atlantic driver does not query the DT for MAC address and will
randomly assign a MAC if the NIC doesn't have a permanent MAC burnt in.
This patch causes the driver to perfer a valid MAC address from OF (if
present) over HW self-reported MAC and only fall back to a random MAC
address when neither of them is valid.
Signed-off-by: Tianhao Chai <cth451@gmail.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rvu_mbox_init(), mbox_regions is not freed or passed out
under the switch-default region, which could lead to a memory leak.
Fix this bug by changing 'return err' to 'goto free_regions'.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_OCTEONTX2_AF=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 98c5611163 (“octeontx2-af: cn10k: Add mbox support for CN10K platform”)
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130165039.192426-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().
Fix this bug by adding a check of mlx4_en_copy_priv()
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: ec25bc04ed ("net/mlx4_en: Add resilience in low memory systems")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Fixes: 7f9664525f ("qlcnic: 83xx memory map and HW access routine")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130110848.109026-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
First set of fixes for v5.16. Mostly crash and driver initialisation
fixes, the fix for rtw89 being most important.
iwlwifi
* compiler, lockdep and smatch warning fixes
* fix for a rare driver initialisation failure
* fix a memory leak
rtw89
* fix const buffer modification causing a kernel crash
mt76
* fix null pointer access
* fix idr leak
rt2x00
* fix driver initialisation errors, a regression since v5.2-rc1
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmGnNJoRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZvHDwf/QYH4ZJyVGzMxo86BQ490ePJbe9uK26F0
uhshAiYj8yjv1PvqjVcSEvDDn+BH1lxLd3lKuWeyGfVCR7m2ZLqRFcESq7QyPMhJ
jY6RUxoj6RAjr/A/zxHFDCTgCWu61ccUgdCuXaOtU3HwOlFHkVgKL94E6EbovKD7
ExAS6eN/+Ga3Rr3eIz0inl637PiiQlVy6/ajVu95YBv/FE5dca1BYEPe/RdSkaWC
IRBlqjYNkrQ2nkqLg3x6M5mrZcJEDZJfomywbEx+JpPfm3hlGlUtwlhUS3v9GBBa
qflM3q1TohqFQmuhA8jOy98/o6Vm/HMvdOHzwoGT1DaXNZzeSYGEEA==
=QUeE
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.16
First set of fixes for v5.16. Mostly crash and driver initialisation
fixes, the fix for rtw89 being most important.
iwlwifi
* compiler, lockdep and smatch warning fixes
* fix for a rare driver initialisation failure
* fix a memory leak
rtw89
* fix const buffer modification causing a kernel crash
mt76
* fix null pointer access
* fix idr leak
rt2x00
* fix driver initialisation errors, a regression since v5.2-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmGnF5oACgkQSD+KveBX
+j7LuQgAuoobAh+fB81CZOxurprZ6E83h8DFOeO0fpvkjye5C6toYnnzxkXPOkCC
FU/Vvsdozn3OTm5kR2glEDSJusezE+bl4KcpU3WX3RNxUQQIMhFt7+GODsIa3WVB
mc0jC6sXH+i7RBJD2IeF4HSELK5PGWjgzn1OFmDhILbngjvxWHxCoP3K+5cia6o7
p8qnP8TyBFyD1vSNqgnPdN4edsavriDtwlO6wvRKDTBecIYHj61nNcFD6GwJCb+j
v6Jp6P3rc5xGWoiZq3k1oi/NUPpfrbRn5SJ+e6VBP+P2JGuzNsY0Y8P+eoX5YhVO
mtfWnFRxLJMpbInxNbUq4cJEpmVtoA==
=lnKZ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2021-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-11-30
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Function mv88e6xxx_serdes_pcs_get_state() currently does not report link
up if AN is enabled, Link bit is set, but Speed and Duplex Resolved bit
is not set, which testing shows is the case for when auto-negotiation
was bypassed (we have AN enabled but link partner does not).
An example of such link partner is Marvell 88X3310 PHY, when put into
the mode where host interface changes between 10gbase-r, 5gbase-r,
2500base-x and sgmii according to copper speed. The 88X3310 does not
enable AN in 2500base-x, and so SerDes on mv88e6xxx currently does not
link with it.
Fix this.
Fixes: a5a6858b79 ("net: dsa: mv88e6xxx: extend phylink to Serdes PHYs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inband AN is broken on Amethyst in 2500base-x mode when set by standard
mechanism (via cmode).
(There probably is some weird setting done by default in the switch for
this mode that make it cycle in some state or something, because when
the peer is the mvneta controller, it receives link change interrupts
every ~0.3ms, but the link is always down.)
Get around this by configuring the PCS mode to 1000base-x (where inband
AN works), and then changing the SerDes frequency while SerDes
transmitter and receiver are disabled, before enabling SerDes PHY. After
disabling SerDes PHY, change the PCS mode back to 2500base-x, to avoid
confusing the device (if we leave it at 1000base-x PCS mode but with
different frequency, and then change cmode to sgmii, the device won't
change the frequency because it thinks it already has the correct one).
The register which changes the frequency is undocumented. I discovered
it by going through all registers in the ranges 4.f000-4.f100 and
1e.8000-1e.8200 for all SerDes cmodes (sgmii, 1000base-x, 2500base-x,
5gbase-r, 10gbase-r, usxgmii) and filtering out registers that didn't
make sense (the value was the same for modes which have different
frequency). The result of this was:
reg sgmii 1000base-x 2500base-x 5gbase-r 10gbase-r usxgmii
04.f002 005b 0058 0059 005c 005d 005f
04.f076 3000 0000 1000 4000 5000 7000
04.f07c 0950 0950 1850 0550 0150 0150
1e.8000 0059 0059 0058 0055 0051 0051
1e.8140 0e20 0e20 0e28 0e21 0e42 0e42
Register 04.f002 is the documented Port Operational Confiuration
register, it's last 3 bits select PCS type, so changing this register
also changes the frequency to the appropriate value.
Registers 04.f076 and 04.f07c are not writable.
Undocumented register 1e.8000 was the one: changing bits 3:0 from 9 to 8
changed SerDes frequency to 3.125 GHz, while leaving the value of PCS
mode in register 04.f002.2:0 at 1000base-x. Inband autonegotiation
started working correctly.
(I didn't try anything with register 1e.8140 since 1e.8000 solved the
problem.)
Since I don't have documentation for this register 1e.8000.3:0, I am
using the constants without names, but my hypothesis is that this
register selects PHY frequency. If in the future I have access to an
oscilloscope able to handle these frequencies, I will try to test this
hypothesis.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fix for erratum 5.2 of the 88E6393X (Amethyst) family: for 10gbase-r
mode, some undocumented registers need to be written some special
values.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save power on 88E6393X by disabling SerDes receiver and transmitter
after SerDes is SerDes is disabled.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for lane is unnecessary, since the function is called only
with allowed lane argument.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to SERDES scripts for 88E6393X, erratum 4.8 has to be applied
every time before SerDes is powered on.
Split the code for erratum 4.8 into separate function and call it in
mv88e6393x_serdes_power().
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e_build_shampo_hd_umr uses counters i and index incorrectly
as unsigned, thus the err state err_unmap could stuck in endless loop.
Change i to int to solve the first issue.
Reduce index check to solve the second issue, the caller function
validates that index could not rotate.
Fixes: 64509b0525 ("net/mlx5e: Add data path for SHAMPO feature")
Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Validate MRTC register is supported before triggering a delayed work
which accesses it.
Fixes: 5a1023deee ("net/mlx5: Add periodic update of host time to firmware")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The log timestamp work should not be queued before the command interface
is initialized, move it to a later stage in the init flow.
Fixes: 5a1023deee ("net/mlx5: Add periodic update of host time to firmware")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The device health recovery flow calls mlx5_health_wait_pci_up() which
queries the device for FW_RESET timeout after freeing the device
timeouts structure on mlx5_function_teardown(). Fix this bug by moving
timeouts structure init/cleanup to the device's init/uninit phases.
Since it is necessary to reset default software timeouts on function
reload, extract setting of defaults values from mlx5_tout_init() and
call mlx5_tout_set_def_val() directly from mlx5_function_setup().
Fixes: 5945e1adea ("net/mlx5: Read timeout values from init segment")
Reported by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When adding rule with multiple destinations, indirect table is used for all of
the destinations if at least one of the destinations support it, this can cause
creation of invalid indirect tables for the destinations that doesn't support it.
Fixed it by using indirect table only if all destinations support it.
Fixes: a508728a4c ("net/mlx5e: VF tunnel RX traffic offloading")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If log_esw_max_sched_depth is not supported group pointer of the vport
is NULL. Hence, check the pointer before reading bw_share value.
Fixes: 0fe132eac3 ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Always use MLX5_FLOW_TABLE_OTHER_VPORT flag when creating egress ACL
table for single FDB. Not doing so on BlueField will make firmware fail
the command. On BlueField the E-Switch manager is the ECPF (vport 0xFFFE)
which is filled in the flow table creation command but as the
other_vport field wasn't set the firmware complains about a bad parameter.
This is different from a regular HCA where the E-Switch manager vport is
the PF (vport 0x0). Passing MLX5_FLOW_TABLE_OTHER_VPORT will make the
firmware happy both on BlueField and on regular HCAs without special
condition for each.
This fixes the bellow firmware syndrome:
mlx5_cmd_check:819:(pid 571): CREATE_FLOW_TABLE(0x930) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x754a4)
Fixes: db202995f5 ("net/mlx5: E-Switch, add logic to enable shared FDB")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
To enable transmit schduler on vport FW require non-zero configuration
for vport's TSAR. If vport added to the group which has configured BW
share value and TX rate values of the vport are zero, then scheduler
wouldn't be enabled on this vport.
Fix that by calling BW normalization if BW share of the new group is
configured.
Fixes: 0fe132eac3 ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When the device is in internal error state, command interface isn't
accessible and the driver decides which commands to fail and which
to ignore.
Move the MODIFY_RQT command to the ignore list in order to avoid
the following redundant warning messages in internal error state:
mlx5_core 0000:82:00.1: mlx5e_rss_disable:419:(pid 23754): Failed to redirect RQT 0x0 to drop RQ 0xc00848: err = -5
mlx5_core 0000:82:00.1: mlx5e_rx_res_channels_deactivate:598:(pid 23754): Failed to redirect direct RQT 0x1 to drop RQ 0xc00848 (channel 0): err = -5
mlx5_core 0000:82:00.1: mlx5e_rx_res_channels_deactivate:607:(pid 23754): Failed to redirect XSK RQT 0x19 to drop RQ 0xc00848 (channel 0): err = -5
Fixes: 43ec0f41fa ("net/mlx5e: Hide all implementation details of mlx5e_rx_res")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Transport Interface Receive (TIR) objects perform the packet processing and
reassembly and is also responsible for demultiplexing the packets into the
different RQs.
There are certain TIR context attributes that propagate to the pointed RQs
and applied to them (like packet_merge offloads (LRO/SHAMPO) and
tunneled_offload_en). When TIRs do not agree on attributes values, a "last
one wins" policy is applied. Hence, if not synced properly, a race between
TIR params update and a concurrent TIR create/modify operation might yield
to a mismatch between the shadow parameters in SW and the actual applied
state of the RQs in HW.
tunneled_offload_en is a fixed attribute per profile, while packet merge
offload state might be toggled and get out-of-sync. When this happens,
packet_merge offload might be working although not requested, or the
opposite.
All updates to packet_merge state and all create/modify operations of
regular redirection/steering TIRs are done under the same priv->state_lock,
so they do not run in parallel, and no race is possible.
However, there are other kind of TIRs (acceleration offloads TIRs, like TLS
TIRs) which are created on demand for each new connection without holding
the coarse priv->state_lock, hence might race.
Fix this by synchronizing all packet_merge state reads and writes against
all TIR create/modify operations. Include the modify operations of the
regular redirection steering TIRs under the new lock, for better code
layering and division of responsibilities.
Fixes: 1182f36593 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited patch added the IPsec support to uplink representor, however
as uplink representors have his private statistics where IPsec stats
is not part of it, that effectively makes IPsec stats hidden when uplink
representor stats queried.
Resolve by adding IPsec stats to uplink representor private statistics.
Fixes: 5589b8f1a2 ("net/mlx5e: Add IPsec support to uplink representor")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Current code wrongly uses the skb->protocol field which reflects the
outer l3 protocol to set the inner l3 type in Software Parser (SWP)
fields settings in the ethernet segment (eseg) in flows where inner
l3 exists like in Vxlan over ESP flow, the above method wrongly use
the outer protocol type instead of the inner one. thus breaking cases
where inner and outer headers have different protocols.
Fix by setting the inner l3 type in SWP according to the inner l3 ip
header version.
Fixes: 2ac9cfe782 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.
WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.
WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.
Fixes: 74f2a5f0ef ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit c55211892f ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.
Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug in which the receiving of packets can stop in the zero-copy
driver. Ice HW ignores 3 lower bits from QRX_TAIL register, which means
that tail is bumped only on intervals of 8. Currently with XSK RX
batching in place, ice_alloc_rx_bufs_zc() clears the status_error0 only
of the last descriptor that has been allocated/taken from the XSK buffer
pool. status_error0 includes DD bit that is looked upon by the
ice_clean_rx_irq_zc() to tell if a descriptor can be processed.
The bug can be triggered when driver updates the ntu but not the
QRX_TAIL, so HW wouldn't have a chance to write to the ready
descriptors. Later on driver moves the ntc to the mentioned set of
descriptors and interprets them as a ready to be processed, since
corresponding DD bits were not cleared nor any writeback has happened
that would clear it. This can then lead to ntc == ntu case which means
that ring is empty and no further packet processing.
Fix the XSK traffic hang that can be observed when l2fwd scenario from
xdpsock is used by making sure that status_error0 is cleared for each
descriptor that is fed to HW and therefore we are sure that driver will
not processed non-valid DD bits. This will also prevent the driver from
processing the descriptors that were allocated in favor of the
previously processed ones, but writeback didn't happen yet.
Fixes: db804cfc21 ("ice: Use the xsk batched rx allocation interface")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.
Use 'bitmap_set()' instead in order not to set unexpected bits.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing mutex_unlock before return from function
ocelot_hwstamp_set() in the ocelot_setup_ptp_traps() error
handling case.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211129151652.1165433-1-weiyongjun1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use 2-factor argument form kvcalloc() instead of kvzalloc().
Link: https://github.com/KSPP/linux/issues/162
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[Jason: Gustavo's link above is for KSPP, but this isn't actually a
security fix, as table_size is bounded to 8192 anyway, and gcc realizes
this, so the codegen comes out to be about the same.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we're being delivered packets from multiple CPUs so quickly that the
ring lock is contended for CPU tries, then it's safe to assume that the
queue is near capacity anyway, so just drop the packet rather than
spinning. This helps deal with multicore DoS that can interfere with
data path performance. It _still_ does not completely fix the issue, but
it again chips away at it.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Apparently the spinlock on incoming_handshake's skb_queue is highly
contended, and a torrent of handshake or cookie packets can bring the
data plane to its knees, simply by virtue of enqueueing the handshake
packets to be processed asynchronously. So, we try switching this to a
ring buffer to hopefully have less lock contention. This alleviates the
problem somewhat, though it still isn't perfect, so future patches will
have to improve this further. However, it at least doesn't completely
diminish the data plane.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Reported-by: Joel Wanner <joel.wanner@inf.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each peer's endpoint contains a dst_cache entry that takes a reference
to another netdev. When the containing namespace exits, we take down the
socket and prevent future sockets from being created (by setting
creating_net to NULL), which removes that potential reference on the
netns. However, it doesn't release references to the netns that a netdev
cached in dst_cache might be taking, so the netns still might fail to
exit. Since the socket is gimped anyway, we can simply clear all the
dst_caches (by way of clearing the endpoint src), which will release all
references.
However, the current dst_cache_reset function only releases those
references lazily. But it turns out that all of our usages of
wg_socket_clear_peer_endpoint_src are called from contexts that are not
exactly high-speed or bottle-necked. For example, when there's
connection difficulty, or when userspace is reconfiguring the interface.
And in particular for this patch, when the netns is exiting. So for
those cases, it makes more sense to call dst_release immediately. For
that, we add a small helper function to dst_cache.
This patch also adds a test to netns.sh from Hangbin Liu to ensure this
doesn't regress.
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: Xiumei Mu <xmu@redhat.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Fixes: 900575aa33 ("wireguard: device: avoid circular netns references")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename module_init & module_exit functions that are named
"mod_init" and "mod_exit" so that they are unique in both the
System.map file and in initcall_debug output instead of showing
up as almost anonymous "mod_init".
This is helpful for debugging and in determining how long certain
module_init calls take to execute.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A __rcu annotation got lost during refactoring, which caused sparse to
become enraged.
Fixes: bf7b042dc6 ("wireguard: allowedips: free empty intermediate nodes when removing single node")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix pointer overwrite in mt7921s_tx_prepare_skb and
mt7663_usb_sdio_tx_prepare_skb routines since in
commit '2a9e9857473b ("mt76: fix possible pktid leak")
mt76_tx_status_skb_add() has been moved out of
mt7921s_write_txwi()/mt7663_usb_sdio_write_txwi() overwriting
hw key pointer in ieee80211_tx_info structure. Fix the issue saving
key pointer before running mt76_tx_status_skb_add().
Fixes: 2a9e985747 ("mt76: fix possible pktid leak")
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/eba40c84b6d114f618e2ae486cc6d0f2e9272cf9.1638193069.git.lorenzo@kernel.org
Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state
Fixes: 508f2e3dce ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.
Fixes: 071a02046c ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.
Fixes: b3f0c79cba ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.
Fixes: c1be0bf092 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link modes were initially added in commit 2c76267943
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds
Florian Fainelli
Sukadev Bhattiprolu
Tianhao Chai
Zhou Qingyang
Stephen Suryaputra
David S. Miller
Marek Behún
Ben Ben-Ishay
Aya Levin
Gal Pressman
Amir Tzin
Maor Dickman
Dmytro Linkin
Mark Bloch
Maor Gottlieb
Moshe Shemesh
Tariq Toukan
Raed Salem
Randy Dunlap
Dongliang Mu
Maciej Fijalkowski
Christophe JAILLET
Wei Yongjun
Gustavo A. R. Silva
Jason A. Donenfeld
Lorenzo Bianconi
Sameer Saurabh
Dmitry Bogdanov
Nikita Danilov
Erik Ekman