Some places use helpers now, others don't. We only have the 'is set'
helper, add helpers for setting and clearing flags too.
It was a bit of a mess of atomic vs non-atomic access. With
BIO_UPTODATE gone, we don't have any risk of concurrent access to the
flags. So relax the restriction and don't make any of them atomic. The
flags that do have serialization issues (reffed and chained), we
already handle those separately.
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: David Teigland <teigland@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054c9 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NeilBrown <neilb@suse.com>
Currently, a bdi (backing_dev_info) embeds single wb (bdi_writeback)
and the role of the separation is unclear. For cgroup support for
writeback IOs, a bdi will be updated to host multiple wb's where each
wb serves writeback IOs of a different cgroup on the bdi. To achieve
that, a wb should carry all states necessary for servicing writeback
IOs for a cgroup independently.
This patch moves bdi->state into wb.
* enum bdi_state is renamed to wb_state and the prefix of all enums is
changed from BDI_ to WB_.
* Explicit zeroing of bdi->state is removed without adding zeoring of
wb->state as the whole data structure is zeroed on init anyway.
* As there's still only one bdi_writeback per backing_dev_info, all
uses of bdi->state are mechanically replaced with bdi->wb.state
introducing no behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: drbd-dev@lists.linbit.com
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This option is not well justified and testing suggests that
it hardly ever makes any difference.
The comment suggests there might be a need to wait for non-resync
activity indicated by ->nr_waiting, however raise_barrier()
already waits for all of that.
So just remove it to simplify reasoning about speed limiting.
This allows us to remove a 'FIXME' comment from raid5.c as that
never used the flag.
Signed-off-by: NeilBrown <neilb@suse.de>
When a drive is marked write-mostly it should only be the
target of reads if there is no other option.
This behaviour was broken by
commit 9dedf60313
md/raid1: read balance chooses idlest disk for SSD
which causes a write-mostly device to be *preferred* is some cases.
Restore correct behaviour by checking and setting
best_dist_disk and best_pending_disk rather than best_disk.
We only need to test one of these as they are both changed
from -1 or >=0 at the same time.
As we leave min_pending and best_dist unchanged, any non-write-mostly
device will appear better than the write-mostly device.
Reported-by: Tomáš Hodek <tomas.hodek@volny.cz>
Reported-by: Dark Penguin <darkpenguin@yandex.ru>
Signed-off-by: NeilBrown <neilb@suse.de>
Link: http://marc.info/?l=linux-raid&m=135982797322422
Fixes: 9dedf60313
Cc: stable@vger.kernel.org (3.6+)
Algorithm:
1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues
ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD)
2. Node 1 sends NEWDISK with uuid and slot number
3. Other nodes issue kobject_uevent_env with uuid and slot number
(Steps 4,5 could be a udev rule)
4. In userspace, the node searches for the disk, perhaps
using blkid -t SUB_UUID=""
5. Other nodes issue either of the following depending on whether the disk
was found:
ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and
disc.number set to slot number)
ioctl(CLUSTERED_DISK_NACK)
6. Other nodes drop lock on no-new-devs (CR) if device is found
7. Node 1 attempts EX lock on no-new-devs
8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk
as SpareLocal
9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED
10. Other nodes understand if the device is added or not by reading the superblock again after receiving the METADATA_UPDATED message.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
set choose_first true for cluster read in read balance when the area
is resyncing.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
If there is a resync going on, all nodes must suspend writes to the
range. This is recorded in the suspend_info/suspend_list.
If there is an I/O within the ranges of any of the suspend_info,
should_suspend will return 1.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
This modifies raid1's narrow_write_error to round up block_sectors to the
device's logical block size.
This prevents sd complaining about "Bad block number requested" for non-512-byte
sector disks.
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Now that the ->stop function only frees the private data,
rename is accordingly.
Also pass in the private pointer as an arg rather than using
mddev->private. This flexibility will be useful in level_store().
Finally, don't clear ->private. It doesn't make sense to clear
it seeing that isn't what we free, and it is no longer necessary
to clear ->private (it was some time ago before ->to_remove was
introduced).
Setting ->to_remove in ->free() is a bit of a wart, but not a
big problem at the moment.
Signed-off-by: NeilBrown <neilb@suse.de>
Each md personality has a 'stop' operation which does two
things:
1/ it finalizes some aspects of the array to ensure nothing
is accessing the ->private data
2/ it frees the ->private data.
All the steps in '1' can apply to all arrays and so can be
performed in common code.
This is useful as in the case where we change the personality which
manages an array (in level_store()), it would be helpful to do
step 1 early, and step 2 later.
So split the 'step 1' functionality out into a new mddev_detach().
Signed-off-by: NeilBrown <neilb@suse.de>
There is no locking around calls to merge_bvec_fn(), so
it is possible that calls which coincide with a level (or personality)
change could go wrong.
So create a central dispatch point for these functions and use
rcu_read_lock().
If the array is suspended, reject any merge that can be rejected.
If not, we know it is safe to call the function.
Signed-off-by: NeilBrown <neilb@suse.de>
There is currently no locking around calls to the 'congested'
bdi function. If called at an awkward time while an array is
being converted from one level (or personality) to another, there
is a tiny chance of running code in an unreferenced module etc.
So add a 'congested' function to the md_personality operations
structure, and call it with appropriate locking from a central
'mddev_congested'.
When the array personality is changing the array will be 'suspended'
so no IO is processed.
If mddev_congested detects this, it simply reports that the
array is congested, which is a safe guess.
As mddev_suspend calls synchronize_rcu(), mddev_congested can
avoid races by included the whole call inside an rcu_read_lock()
region.
This require that the congested functions for all subordinate devices
can be run under rcu_lock. Fortunately this is the case.
Signed-off-by: NeilBrown <neilb@suse.de>
If a devices is being recovered it is not InSync and is not Faulty.
If a read error is experienced on that device, fix_read_error()
will be called, but it ignores non-InSync devices. So it will
neither fix the error nor fail the device.
It is incorrect that fix_read_error() ignores non-InSync devices.
It should only ignore Faulty devices. So fix it.
This became a bug when we allowed reading from a device that was being
recovered. It is suitable for any subsequent -stable kernel.
Fixes: da8840a747
Cc: stable@vger.kernel.org (v3.5+)
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Both normal IO and resync IO can be retried with reschedule_retry()
and so be counted into ->nr_queued, but only normal IO gets counted in
->nr_pending.
Before the recent improvement to RAID1 resync there could only
possibly have been one or the other on the queue. When handling a
read failure it could only be normal IO. So when handle_read_error()
called freeze_array() the fact that freeze_array only compares
->nr_queued against ->nr_pending was safe.
But now that these two types can interleave, we can have both normal
and resync IO requests queued, so we need to count them both in
nr_pending.
This error can lead to freeze_array() hanging if there is a read
error, so it is suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
raise_barrier() uses next_resync as part of its calculations, so it
really should be updated first, instead of afterwards.
next_resync is always used under resync_lock so update it under
resync lock to, just before it is used. That is safest.
This could cause normal IO and resync IO to interact badly so
it suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
next_resync is (approximately) the location for the next resync request.
However it does *not* reliably determine the earliest location
at which resync might be happening.
This is because resync requests can complete out of order, and
we only limit the number of current requests, not the distance
from the earliest pending request to the latest.
mddev->curr_resync_completed is a reliable indicator of the earliest
position at which resync could be happening. It is updated less
frequently, but is actually reliable which is more important.
So use it to determine if a write request is before the region
being resynced and so safe from conflict.
This error can allow resync IO to interfere with normal IO which
could lead to data corruption. Hence: stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
The resync/recovery process for raid1 was recently changed
so that writes could happen in parallel with resync providing
they were in different regions of the device.
There is a problem though: While a write request will always
wait for conflicting resync to complete, a resync request
will *not* always wait for conflicting writes to complete.
Two changes are needed to fix this:
1/ raise_barrier (which waits until it is safe to do resync)
must wait until current_window_requests is zero
2/ wait_battier (which waits at the start of a new write request)
must update current_window_requests if the request could
possible conflict with a concurrent resync.
As concurrent writes and resync can lead to data loss,
this patch is suitable for -stable.
Fixes: 79ef3a8aa1
Cc: stable@vger.kernel.org (v3.13+)
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If there are outstanding writes when close_sync is called,
the change to ->start_next_window might cause them to
decrement the wrong counter when they complete. Fix this
by merging the two counters into the one that will be decremented.
Having an incorrect value in a counter can cause raise_barrier()
to hangs, so this is suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
commit 79ef3a8aa1 made
it possible for reads to happen concurrently with resync.
This means that we need to be more careful where read_balancing
is allowed during resync - we can no longer be sure that any
resync that has already started will definitely finish.
So keep read_balancing to before recovery_cp, which is conservative
but safe.
This bug makes it possible to read from a device that doesn't
have up-to-date data, so it can cause data corruption.
So it is suitable for any kernel since 3.11.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
r1_bio->start_next_window is not initialised in the READ
case, so allow_barrier may incorrectly decrement
conf->current_window_requests
which can cause raise_barrier() to block forever.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't abort recovery on a write error if the write error
to the recovering device was triggerd by normal IO (as opposed to
recovery IO).
This means that for one bitmap region, the recovery might write to the
recovering device for a few sectors, then not bother for subsequent
sectors (as it never writes to failed devices). In this case
the bitmap bit will be cleared, but it really shouldn't.
The result is that if the recovering device fails and is then re-added
(after fixing whatever hardware problem triggerred the failure),
the second recovery won't redo the region it was in the middle of,
so some of the device will not be recovered properly.
If we abort the recovery, the region being processes will be cancelled
(bit not cleared) and the whole region will be retried.
As the bug can result in data corruption the patch is suitable for
-stable. For kernels prior to 3.11 there is a conflict in raid10.c
which will require care.
Original-from: jiao hui <jiaohui@bwstor.com.cn>
Reported-and-tested-by: jiao hui <jiaohui@bwstor.com.cn>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org
When performing a user-request check/repair (MD_RECOVERY_REQUEST is set)
on a raid1, we allocate multiple bios each with their own set of pages.
If the page allocations for one bio fails, we currently do *not* free
the pages allocated for the previous bios, nor do we free the bio itself.
This patch frees all the already-allocate pages, and makes sure that
all the bios are freed as well.
This bug can cause a memory leak which can ultimately OOM a machine.
It was introduced in 3.10-rc1.
Fixes: a07876064a
Cc: Kent Overstreet <koverstreet@google.com>
Cc: stable@vger.kernel.org (3.10+)
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 30bc9b5387
md/raid1: fix bio handling problems in process_checks()
Move the bio_reset() to a point before where BIO_UPTODATE is checked,
so that check now always report that the bio is uptodate, even if it is not.
This causes process_check() to sometimes treat read-errors as
successful matches so the good data isn't written out.
This patch preserves the flag until it is needed.
Bug was introduced in 3.11, but backported to 3.10-stable (as it fixed
an even worse bug). So suitable for any -stable since 3.10.
Reported-and-tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@vger.kernel.org (3.10+)
Fixed: 30bc9b5387
Signed-off-by: NeilBrown <neilb@suse.de>
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
The new iobarrier implementation in raid1 (which keeps normal writes
and resync activity separate) counts every request what is not before
the current resync point in either next_window_requests or
current_window_requests.
It flags that the request is counted by setting ->start_next_window.
allow_barrier follows this model exactly and decrements one of the
*_window_requests if and only if ->start_next_window is set.
However wait_barrier(), which increments *_window_requests uses a
slightly different test for setting -.start_next_window (which is set
from the return value of this function).
So there is a possibility of the counts getting out of sync, and this
leads to the resync hanging.
So change wait_barrier() to return a non-zero value in exactly the
same cases that it increments *_window_requests.
But was introduced in 3.13-rc1.
Reported-by: Bruno Wolff III <bruno@wolff.to>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68061
Fixes: 79ef3a8aa1
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io
during resync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8RCg
-----END PGP SIGNATURE-----
Merge tag 'md/3.13' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io during
resync"
* tag 'md/3.13' of git://neil.brown.name/md:
md/raid5: Use conf->device_lock protect changing of multi-thread resources.
md/raid5: Before freeing old multi-thread worker, it should flush them.
md/raid5: For stripe with R5_ReadNoMerge, we replace REQ_FLUSH with REQ_NOMERGE.
UAPI: include <asm/byteorder.h> in linux/raid/md_p.h
raid1: Rewrite the implementation of iobarrier.
raid1: Add some macros to make code clearly.
raid1: Replace raise_barrier/lower_barrier with freeze_array/unfreeze_array when reconfiguring the array.
raid1: Add a field array_frozen to indicate whether raid in freeze state.
md: Convert use of typedef ctl_table to struct ctl_table
md/raid5: avoid deadlock when raid5 array has unack badblocks during md_stop_writes.
md: use MD_RECOVERY_INTR instead of kthread_should_stop in resync thread.
md: fix some places where mddev_lock return value is not checked.
raid5: Retry R5_ReadNoMerge flag when hit a read error.
raid5: relieve lock contention in get_active_stripe()
raid5: relieve lock contention in get_active_stripe()
wait: add wait_event_cmd()
md/raid5.c: add proper locking to error path of raid5_start_reshape.
md: fix calculation of stacking limits on level change.
raid5: Use slow_path to release stripe when mddev->thread is null
There is an iobarrier in raid1 because of contention between normal IO and
resync IO. It suspends all normal IO when resync/recovery happens.
However if normal IO is out side the resync window, there is no contention.
So this patch changes the barrier mechanism to only block IO that
could contend with the resync that is currently happening.
We partition the whole space into five parts.
|---------|-----------|------------|----------------|-------|
start next_resync start_next_window end_window
start + RESYNC_WINDOW = next_resync
next_resync + NEXT_NORMALIO_DISTANCE = start_next_window
start_next_window + NEXT_NORMALIO_DISTANCE = end_window
Firstly we introduce some concepts:
1 - RESYNC_WINDOW: For resync, there are 32 resync requests at most at the
same time. A sync request is RESYNC_BLOCK_SIZE(64*1024).
So the RESYNC_WINDOW is 32 * RESYNC_BLOCK_SIZE, that is 2MB.
2 - NEXT_NORMALIO_DISTANCE: the distance between next_resync
and start_next_window. It also indicates the distance between
start_next_window and end_window.
It is currently 3 * RESYNC_WINDOW_SIZE but could be tuned if
this turned out not to be optimal.
3 - next_resync: the next sector at which we will do sync IO.
4 - start: a position which is at most RESYNC_WINDOW before
next_resync.
5 - start_next_window: a position which is NEXT_NORMALIO_DISTANCE
beyond next_resync. Normal-io after this position doesn't need to
wait for resync-io to complete.
6 - end_window: a position which is 2 * NEXT_NORMALIO_DISTANCE beyond
next_resync. This also doesn't need to wait, but is counted
differently.
7 - current_window_requests: the count of normalIO between
start_next_window and end_window.
8 - next_window_requests: the count of normalIO after end_window.
NormalIO will be partitioned into four types:
NormIO1: the end sector of bio is smaller or equal the start
NormIO2: the start sector of bio larger or equal to end_window
NormIO3: the start sector of bio larger or equal to
start_next_window.
NormIO4: the location between start_next_window and end_window
|--------|-----------|--------------------|----------------|-------------|
| start | next_resync | start_next_window | end_window |
NormIO1 NormIO4 NormIO4 NormIO3 NormIO2
For NormIO1, we don't need any io barrier.
For NormIO4, we used a similar approach to the original iobarrier
mechanism. The normalIO and resyncIO must be kept separate.
For NormIO2/3, we add two fields to struct r1conf: "current_window_requests"
and "next_window_requests". They indicate the count of active
requests in the two window.
For these, we don't wait for resync io to complete.
For resync action, if there are NormIO4s, we must wait for it.
If not, we can proceed.
But if resync action reaches start_next_window and
current_window_requests > 0 (that is there are NormIO3s), we must
wait until the current_window_requests becomes zero.
When current_window_requests becomes zero, start_next_window also
moves forward. Then current_window_requests will replaced by
next_window_requests.
There is a problem which when and how to change from NormIO2 to
NormIO3. Only then can sync action progress.
We add a field in struct r1conf "start_next_window".
A: if start_next_window == MaxSector, it means there are no NormIO2/3.
So start_next_window = next_resync + NEXT_NORMALIO_DISTANCE
B: if current_window_requests == 0 && next_window_requests != 0, it
means start_next_window move to end_window
There is another problem which how to differentiate between
old NormIO2(now it is NormIO3) and NormIO2.
For example, there are many bios which are NormIO2 and a bio which is
NormIO3. NormIO3 firstly completed, so the bios of NormIO2 became NormIO3.
We add a field in struct r1bio "start_next_window".
This is used to record the position conf->start_next_window when the call
to wait_barrier() is made in make_request().
In allow_barrier(), we check the conf->start_next_window.
If r1bio->stat_next_window == conf->start_next_window, it means
there is no transition between NormIO2 and NormIO3.
If r1bio->start_next_window != conf->start_next_window, it mean
there was a transition between NormIO2 and NormIO3. There can only
have been one transition. So it only means the bio is old NormIO2.
For one bio, there may be many r1bio's. So we make sure
all the r1bio->start_next_window are the same value.
If we met blocked_dev in make_request(), it must call allow_barrier
and wait_barrier. So the former and the later value of
conf->start_next_window will be change.
If there are many r1bio's with differnet start_next_window,
for the relevant bio, it depend on the last value of r1bio.
It will cause error. To avoid this, we must wait for previous r1bios
to complete.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In a subsequent patch, we'll use some const parameters.
Using macros will make the code clearly.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We used to use raise_barrier to suspend normal IO while we reconfigure
the array. However raise_barrier will soon only suspend some normal
IO, not all. So we need something else.
Change it to use freeze_array.
But freeze_array not only suspends normal io, it also suspends
resync io.
For the place where call raise_barrier for reconfigure, it isn't a
problem.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because the following patch will rewrite the content between normal IO
and resync IO. So we used a parameter to indicate whether raid is in freeze
array.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Someone cut and pasted md's md_trim_bio() into xen-blkfront.c. Come on,
we should know better than this.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since:
commit 7ceb17e87b
md: Allow devices to be re-added to a read-only array.
spares are activated on a read-only array. In case of raid1 and raid10
personalities it causes that not-in-sync devices are marked in-sync
without checking if recovery has been finished.
If a read-only array is degraded and one of its devices is not in-sync
(because the array has been only partially recovered) recovery will be skipped.
This patch adds checking if recovery has been finished before marking a device
in-sync for raid1 and raid10 personalities. In case of raid5 personality
such condition is already present (at raid5.c:6029).
Bug was introduced in 3.10 and causes data corruption.
Cc: stable@vger.kernel.org
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Recent change to use bio_copy_data() in raid1 when repairing
an array is faulty.
The underlying may have changed the bio in various ways using
bio_advance and these need to be undone not just for the 'sbio' which
is being copied to, but also the 'pbio' (primary) which is being
copied from.
So perform the reset on all bios that were read from and do it early.
This also ensure that the sbio->bi_io_vec[j].bv_len passed to
memcmp is correct.
This fixes a crash during a 'check' of a RAID1 array. The crash was
introduced in 3.10 so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add ability to restore transiently failed devices on resume
This patch adds code to the resume function to check over the devices
in the RAID array. If any are found to be marked as failed and their
superblocks can be read, an attempt is made to reintegrate them into
the array. This allows the user to refresh the array with a simple
suspend and resume of the array - rather than having to load a
completely new table, allocate and initialize all the structures and
throw away the old instantiation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIVAwUAUbl1mznsnt1WYoG5AQKGlQ//eixdawF+DUK5hadqZ9EDni+BAVzb7m69
+zU6ilQ7UOh7bxtAoJqrgFVykK+LG8wvYsEBwMjB9oRDLA96/YDXXiBzXHvd6mGh
g271lwMTQ9h+O8L6psLUX6qsrH3i7SJmF8ySPKi6Fe5ruT8ToOB8Ii8XQebEZdXo
VOzRz2VgSTcBdrTyKPDsBJByDQX36hsK8Gs5YSl5F3nvyV4dvGWMlyoTF1TRRt9K
YCCZ8pSk3kTXaSdl0syrJxI17pEUC8mtcA01S6JD/GV49CGO8LYAckVJ4ijWw7VV
IGGlH0DsYSMgJ7yyuLz4ifaqRnsWsAGW0WyiZYYKvjtNUiyBuBBbo2cQ1lNkR5p4
jnLhpJJVh0hLCPn6wcCWIBIdT/mFaBpXkvZPd3ks5kefGXsfpVPm0fK8r0fzkzgy
tJCZtZFZHeK1qsgaDsiS76S2ZNcFh0HQVIa84Q200/XUDgh8dYlD0+7oIsVu0UBZ
72Aop+Ak9+k4vKTvB9/hpcY+Rt0MI7zKewXBDSDK1sXhIHLQqv8rCEeNYiuPPqr/
ghRukn+C/Wtr7JYBsX+jMjxtmSzYtwBOihwLoZCH9pp3C5jTvyQk9s8n1j13V2RK
sAFtfpCVoQ8tTa7IITKRMfftzHn1WiPlPsj6VbigJ6A4N98csgv7x2rF7FyqcF0X
aoj69nQ3i/4=
=8iy3
-----END PGP SIGNATURE-----
Merge tag 'md-3.10-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few bugfixes for md
Some tagged for -stable"
* tag 'md-3.10-fixes' of git://neil.brown.name/md:
md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in place
md/raid1,raid10: use freeze_array in place of raise_barrier in various places.
md/raid1: consider WRITE as successful only if at least one non-Faulty and non-rebuilding drive completed it.
md: md_stop_writes() should always freeze recovery.
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Cc: stable@vger.kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Various places in raid1 and raid10 are calling raise_barrier when they
really should call freeze_array.
The former is only intended to be called from "make_request".
The later has extra checks for 'nr_queued' and makes a call to
flush_pending_writes(), so it is safe to call it from within the
management thread.
Using raise_barrier will sometimes deadlock. Using freeze_array
should not.
As 'freeze_array' currently expects one request to be pending (in
handle_read_error - the only previous caller), we need to pass
it the number of pending requests (extra) to ignore.
The deadlock was made particularly noticeable by commits
050b66152f (raid10) and 6b740b8d79 (raid1) which
appeared in 3.4, so the fix is appropriate for any -stable
kernel since then.
This patch probably won't apply directly to some early kernels and
will need to be applied by hand.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
In SSD/hard disk hybid storage, discard request should be ignored for hard
disk. We used to be doing this way, but the unplug path forgets it.
This is suitable for stable tree since v3.6.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Hi.
Raid1 and raid10 devices leak memory every time they stop.
This is a patch for linux-3.9.0-rc7 to fix this problem.
Thanks,
Hirokazu Takahashi.
Signed-off-by: Hirokazu Takahashi <taka@valinux.co.jp>
Signed-off-by: NeilBrown <neilb@suse.de>
More prep work for immutable bvecs:
A few places in the code were either open coding or using the wrong
version - fix.
After we introduce the bvec iter, it'll no longer be possible to modify
the biovec through bio_for_each_segment_all() - it doesn't increment a
pointer to the current bvec, you pass in a struct bio_vec (not a
pointer) which is updated with what the current biovec would be (taking
into account bi_bvec_done and bi_size).
So because of that it's more worthwhile to be consistent about
bio_for_each_segment()/bio_for_each_segment_all() usage.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Alexander Viro <viro@zeniv.linux.org.uk>
__bio_for_each_segment() iterates bvecs from the specified index
instead of bio->bv_idx. Currently, the only usage is to walk all the
bvecs after the bio has been advanced by specifying 0 index.
For immutable bvecs, we need to split these apart;
bio_for_each_segment() is going to have a different implementation.
This will also help document the intent of code that's using it -
bio_for_each_segment_all() is only legal to use for code that owns the
bio.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Neil Brown <neilb@suse.de>
CC: Boaz Harrosh <bharrosh@panasas.com>
This doesn't really delete any code _yet_, but once immutable bvecs are
done we can just delete the rest of the code in that loop.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
More bi_idx removal. This code was just open coding bio_clone(). This
could probably be further improved by using bio_advance() instead of
skipping over null pages, but that'd be a larger rework.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Random cleanup - this code was duplicated and it's not really specific
to md.
Also added the ability to return the actual error code.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Bunch of places in the code weren't using it where they could be -
this'll reduce the size of the patch that puts bi_sector/bi_size/bi_idx
into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: "Ed L. Cashin" <ecashin@coraid.com>
CC: Nick Piggin <npiggin@kernel.dk>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jim Paris <jim@jtan.com>
CC: Geoff Levand <geoff@infradead.org>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ed Cashin <ecashin@coraid.com>
Just a little convenience macro - main reason to add it now is preparing
for immutable bio vecs, it'll reduce the size of the patch that puts
bi_sector/bi_size/bi_idx into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux-s390@vger.kernel.org
CC: Chris Mason <chris.mason@fusionio.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
When raid1/raid10 needs to fix a read error, it first drains
all pending requests by calling freeze_array().
This calls flush_pending_writes() if it needs to sleep,
but some writes may be pending in a per-process plug rather
than in the per-array request queue.
When raid1{,0}_unplug() moves the request from the per-process
plug to the per-array request queue (from which
flush_pending_writes() can flush them), it needs to wake up
freeze_array(), or freeze_array() will never flush them and so
it will block forever.
So add the requires wake_up() calls.
This bug was introduced by commit
f54a9d0e59
for raid1 and a similar commit for RAID10, and so has been present
since linux-3.6. As the bug causes a deadlock I believe this fix is
suitable for -stable.
Cc: stable@vger.kernel.org (3.6.y 3.7.y 3.8.y)
Reported-by: Tregaron Bayly <tbayly@bluehost.com>
Tested-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Set mddev queue's max_write_same_sectors to its chunk_sector value (before
disk_stack_limits merges the underlying disk limits.) With that in place,
be sure to handle writes coming down from the block layer that have the
REQ_WRITE_SAME flag set. That flag needs to be copied into any newly cloned
write bio.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block driver update from Jens Axboe:
"Now that the core bits are in, here are the driver bits for 3.8. The
branch contains:
- A huge pile of drbd bits that were dumped from the 3.7 merge
window. Following that, it was both made perfectly clear that
there is going to be no more over-the-wall pulls and how the
situation on individual pulls can be improved.
- A few cleanups from Akinobu Mita for drbd and cciss.
- Queue improvement for loop from Lukas. This grew into adding a
generic interface for waiting/checking an even with a specific
lock, allowing this to be pulled out of md and now loop and drbd is
also using it.
- A few fixes for xen back/front block driver from Roger Pau Monne.
- Partition improvements from Stephen Warren, allowing partiion UUID
to be used as an identifier."
* 'for-3.8/drivers' of git://git.kernel.dk/linux-block: (609 commits)
drbd: update Kconfig to match current dependencies
drbd: Fix drbdsetup wait-connect, wait-sync etc... commands
drbd: close race between drbd_set_role and drbd_connect
drbd: respect no-md-barriers setting also when changed online via disk-options
drbd: Remove obsolete check
drbd: fixup after wait_even_lock_irq() addition to generic code
loop: Limit the number of requests in the bio list
wait: add wait_event_lock_irq() interface
xen-blkfront: free allocated page
xen-blkback: move free persistent grants code
block: partition: msdos: provide UUIDs for partitions
init: reduce PARTUUID min length to 1 from 36
block: store partition_meta_info.uuid as a string
cciss: use check_signature()
cciss: cleanup bitops usage
drbd: use copy_highpage
drbd: if the replication link breaks during handshake, keep retrying
drbd: check return of kmalloc in receive_uuids
drbd: Broadcast sync progress no more often than once per second
drbd: don't try to clear bits once the disk has failed
...
New wait_event{_interruptible}_lock_irq{_cmd} macros added. This commit
moves the private wait_event_lock_irq() macro from MD to regular wait
includes, introduces new macro wait_event_lock_irq_cmd() instead of using
the old method with omitting cmd parameter which is ugly and makes a use
of new macros in the MD. It also introduces the _interruptible_ variant.
The use of new interface is when one have a special lock to protect data
structures used in the condition, or one also needs to invoke "cmd"
before putting it to sleep.
All new macros are expected to be called with the lock taken. The lock
is released before sleep and is reacquired afterwards. We will leave the
macro with the lock held.
Note to DM: IMO this should also fix theoretical race on waitqueue while
using simultaneously wait_event_lock_irq() and wait_event() because of
lack of locking around current state setting and wait queue removal.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the raid1 or raid10 unplug function gets called
from a make_request function (which is very possible) when
there are bios on the current->bio_list list, then it will not
be able to successfully call bitmap_unplug() and it could
need to submit more bios and wait for them to complete.
But they won't complete while current->bio_list is non-empty.
So detect that case and handle the unplugging off to another thread
just like we already do when called from within the scheduler.
RAID1 version of bug was introduced in 3.6, so that part of fix is
suitable for 3.6.y. RAID10 part won't apply.
Cc: stable@vger.kernel.org
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reported-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Signed-off-by: NeilBrown <neilb@suse.de>
setup_conf in raid1.c uses conf->raid_disks before assigning
a value. It is used when including 'Replacement' devices.
The consequence is that assembling an array which contains a
replacement will misbehave and either not include the replacement, or
not include the device being replaced.
Though this doesn't lead directly to data corruption, it could lead to
reduced data safety.
So use mddev->raid_disks, which is initialised, instead.
Bug was introduced by commit c19d57980b
md/raid1: recognise replacements when assembling arrays.
in 3.3, so fix is suitable for 3.3.y thru 3.6.y.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Now that multiple threads can handle stripes, it is safer to
use an atomic64_t for resync_mismatches, to avoid update races.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a read error, we arrange for raid1d to handle it.
Currently we release the reference on the device. This can result
in
conf->mirrors[read_disk].rdev
being NULL in fix_read_error, if the device happens to get removed
before the read error is handled.
So instead keep the reference until the read error has been fully
handled.
Reported-by: hank <pyu@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Change the thread parameter, so the thread can carry extra info. Next patch
will use it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes md raid 1 support TRIM.
If one disk supports discard and another not, or one has discard_zero_data and
another not, there could be inconsistent between data from such disks. But this
should not matter, discarded data is useless. This will add extra copy in rebuild
though.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block driver changes from Jens Axboe:
- Making the plugging support for drivers a bit more sane from Neil.
This supersedes the plugging change from Shaohua as well.
- The usual round of drbd updates.
- Using a tail add instead of a head add in the request completion for
ndb, making us find the most completed request more quickly.
- A few floppy changes, getting rid of a duplicated flag and also
running the floppy init async (since it takes forever in boot terms)
from Andi.
* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
floppy: remove duplicated flag FD_RAW_NEED_DISK
blk: pass from_schedule to non-request unplug functions.
block: stack unplug
blk: centralize non-request unplug handling.
md: remove plug_cnt feature of plugging.
block/nbd: micro-optimization in nbd request completion
drbd: announce FLUSH/FUA capability to upper layers
drbd: fix max_bio_size to be unsigned
drbd: flush drbd work queue before invalidate/invalidate remote
drbd: fix potential access after free
drbd: call local-io-error handler early
drbd: do not reset rs_pending_cnt too early
drbd: reset congestion information before reporting it in /proc/drbd
drbd: report congestion if we are waiting for some userland callback
drbd: differentiate between normal and forced detach
drbd: cleanup, remove two unused global flags
floppy: Run floppy initialization asynchronous
This seemed like a good idea at the time, but after further thought I
cannot see it making a difference other than very occasionally and
testing to try to exercise the case it is most likely to help did not
show any performance difference by removing it.
So remove the counting of active plugs and allow 'pending writes' to
be activated at any time, not just when no plugs are active.
This is only relevant when there is a write-intent bitmap, and the
updating of the bitmap will likely introduce enough delay that
the single-threading of bitmap updates will be enough to collect large
numbers of updates together.
Removing this will make it easier to centralise the unplug code, and
will clear the other for other unplug enhancements which have a
measurable effect.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When doing resync or repair, attempt to correct bad blocks, according
to WriteErrorSeen policy
Signed-off-by: Alex Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a resync of a RAID1 array with 2 devices finds a known bad block
one device it will neither read from, or write to, that device for
this block offset.
So there will be one read_target (The other device) and zero write
targets.
This condition causes md/raid1 to abort the resync assuming that it
has finished - without known bad blocks this would be true.
When there are no write targets because of the presence of bad blocks
we should only skip over the area covered by the bad block.
RAID10 already gets this right, raid1 doesn't. Or didn't.
As this can cause a 'sync' to abort early and appear to have succeeded
it could lead to some data corruption, so it suitable for -stable.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For SSD, if request size exceeds specific value (optimal io size), request size
isn't important for bandwidth. In such condition, if making request size bigger
will cause some disks idle, the total throughput will actually drop. A good
example is doing a readahead in a two-disk raid1 setup.
So when should we split big requests? We absolutly don't want to split big
request to very small requests. Even in SSD, big request transfer is more
efficient. This patch only considers request with size above optimal io size.
If all disks are busy, is it worth doing a split? Say optimal io size is 16k,
two requests 32k and two disks. We can let each disk run one 32k request, or
split the requests to 4 16k requests and each disk runs two. It's hard to say
which case is better, depending on hardware.
So only consider case where there are idle disks. For readahead, split is
always better in this case. And in my test, below patch can improve > 30%
thoughput. Hmm, not 100%, because disk isn't 100% busy.
Such case can happen not just in readahead, for example, in directio. But I
suppose directio usually will have bigger IO depth and make all disks busy, so
I ignored it.
Note: if the raid uses any hard disk, we don't prevent merging. That will make
performace worse.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
SSD hasn't spindle, distance between requests means nothing. And the original
distance based algorithm sometimes can cause severe performance issue for SSD
raid.
Considering two thread groups, one accesses file A, the other access file B.
The first group will access one disk and the second will access the other disk,
because requests are near from one group and far between groups. In this case,
read balance might keep one disk very busy but the other relative idle. For
SSD, we should try best to distribute requests to as many disks as possible.
There isn't spindle move penality anyway.
With below patch, I can see more than 50% throughput improvement sometimes
depending on workloads.
The only exception is small requests can be merged to a big request which
typically can drive higher throughput for SSD too. Such small requests are
sequential reads. Unlike hard disk, sequential read which can't be merged (for
example direct IO, or read without readahead) can be ignored for SSD. Again
there is no spindle move penality. readahead dispatches small requests and such
requests can be merged.
Last patch can help detect sequential read well, at least if concurrent read
number isn't greater than raid disk number. In that case, distance based
algorithm doesn't work well too.
V2: For hard disk and SSD mixed raid, doesn't use distance based algorithm for
random IO too. This makes the algorithm generic for raid with SSD.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the sequential read detection is global wide. It's natural to make it
per disk based, which can improve the detection for concurrent multiple
sequential reads. And next patch will make SSD read balance not use distance
based algorithm, where this change help detect truly sequential read for SSD.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1/RAID10: Move some macros from .h file to .c file
There are three macros (IO_BLOCKED,IO_MADE_GOOD,BIO_SPECIAL) which are defined
in both raid1.h and raid10.h. They are only used in there respective .c files.
However, if we wish to make RAID10 accessible to the device-mapper RAID
target (dm-raid.c), then we need to move these macros into the .c files where
they are used so that they do not conflict with each other.
The macros from the two files are identical and could be moved into md.h, but
I chose to leave the duplication and have them remain in the personality
files.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1: Rename the structure 'mirror_info' to 'raid1_info'
The same structure name ('mirror_info') is used by raid10. Each of these
structures are defined in there respective header files. If dm-raid is
to support both RAID1 and RAID10, the header files will be included and
the structure names must not collide. While only one of these structure
names needs to change, this patch adds consistency to the naming of the
structure.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 4367af5561
md/raid1: clear bad-block record when write succeeds.
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
Also commit 73d5c38a95
md: avoid races when stopping resync.
Fix a race condition in this same code in end_sync_write but didn't
make the change in sync_request_write.
This patch updates sync_request_write to fix both of those.
Patch is suitable for 3.1 and later kernels.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Original-version-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
This bug has been present ever since data-check was introduce
in 2.6.16. However it would only fire if a data-check were
done on a degraded array, which was only possible if the array
has 3 or more devices. This is certainly possible, but is quite
uncommon.
Since hot-replace was added in 3.3 it can happen more often as
the same condition can arise if not all possible replacements are
present.
The problem is that as soon as we submit the last read request, the
'r1_bio' structure could be freed at any time, so we really should
stop looking at it. If the last device is being read from we will
stop looking at it. However if the last device is not due to be read
from, we will still check the bio pointer in the r1_bio, but the
r1_bio might already be free.
So use the read_targets counter to make sure we stop looking for bios
to submit as soon as we have submitted them all.
This fix is suitable for any -stable kernel since 2.6.16.
Cc: stable@vger.kernel.org
Reported-by: Arnold Schulz <arnysch@gmx.net>
Signed-off-by: NeilBrown <neilb@suse.de>
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The new merge_bvec_fn which calls the corresponding function
in subsidiary devices requires that mddev->merge_check_needed
be set if any child has a merge_bvec_fn.
However were were only setting that when a device was hot-added,
not when a device was present from the start.
This bug was introduced in 3.4 so patch is suitable for 3.4.y
kernels. However that are conflicts in raid10.c so a separate
patch will be needed for 3.4.y.
Cc: stable@vger.kernel.org
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A RAID1 device does not necessarily need a fullsync if the bitmap can be used instead.
Similar to commit d6b212f4b1 in raid5.c, if a raid1
device can be brought back (i.e. from a transient failure) it shouldn't need a
complete resync. Provided the bitmap is not to old, it will have recorded the areas
of the disk that need recovery.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Now that bitmaps can be resized, we can allow an array to be resized
while the bitmap is present.
This only covers resizing that involves changing the effective size
of member devices, not resizing that changes the number of devices.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to fix a read error, it is acceptable to read from a
device that is recovering, provided the recovery has got past the
place we are reading from. This makes the test for "can we read from
here" the same as the test in read_balance.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).
So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.
(As we didn't previous check that all 'pad' fields were zero,
we need a new FEATURE flag for this.
A (belatedly) check that all remaining 'pad' fields are
zero to avoid a repeat of this)
The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.
This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be. At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.
When a reshape finishes we will need to update the data_offset
and rdev->sectors. So provide an exported function to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
If r1bio->sectors % 8 != 0,then the memcmp and a later
memcpy will omit the last bio_vec.
This is suitable for any stable kernel since 3.1 when bad-block
management was introduced.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When comparing two pages read from different legs of a mirror, only
compare the bytes that were read, not the whole page.
In most cases we read a whole page, but in some cases with
bad blocks or odd sizes devices we might read fewer than that.
This bug has been present "forever" but at worst it might cause
a report of two many mismatches and generate a little bit
extra resync IO, so there is no need to back-port to -stable
kernels.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because rde->nr_pending > 0,so can not remove this disk.
And in any case, we aren't holding rcu_read_lock()
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't honour merge_bvec_fn in member devices so if there
is one, we force all requests to be single-page at most.
This is not ideal.
So create a raid1 merge_bvec_fn to check that function in children
as well.
This introduces a small problem. There is no locking around calls
the ->merge_bvec_fn and subsequent calls to ->make_request. So a
device added between these could end up getting a request which
violates its merge_bvec_fn.
Currently the best we can do is synchronize_sched(). This will work
providing no preemption happens. If there is is preemption, we just
have to hope that new devices are largely consistent with old devices.
Signed-off-by: NeilBrown <neilb@suse.de>
md.h has an 'rdev_for_each()' macro for iterating the rdevs in an
mddev. However it uses the 'safe' version of list_for_each_entry,
and so requires the extra variable, but doesn't include 'safe' in the
name, which is useful documentation.
Consequently some places use this safe version without needing it, and
many use an explicity list_for_each entry.
So:
- rename rdev_for_each to rdev_for_each_safe
- create a new rdev_for_each which uses the plain
list_for_each_entry,
- use the 'safe' version only where needed, and convert all other
list_for_each_entry calls to use rdev_for_each.
Signed-off-by: NeilBrown <neilb@suse.de>
If RAID1 or RAID10 is used under LVM or some other stacking
block device, it is possible to enter a deadlock during
resync or recovery.
This can happen if the upper level block device creates
two requests to the RAID1 or RAID10. The first request gets
processed, blocks recovery and queue requests for underlying
requests in current->bio_list. A resync request then starts
which will wait for those requests and block new IO.
But then the second request to the RAID1/10 will be attempted
and it cannot progress until the resync request completes,
which cannot progress until the underlying device requests complete,
which are on a queue behind that second request.
So allow that second request to proceed even though there is
a resync request about to start.
This is suitable for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Ray Morris <support@bettercgi.com>
Tested-by: Ray Morris <support@bettercgi.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Since we added 'replacement' capability, RAID1 can have twice
as many devices as ->raid_disks indicates.
So md_raid1_congested needs to check that many possible devices,
not just ->raid_disks many.
Signed-off-by: NeilBrown <neilb@suse.de>
We normally try to avoid reading from write-mostly devices, but when
we do we really have to check for bad blocks and be sure not to
try reading them.
With the current code, best_good_sectors might not get set and that
causes zero-length read requests to be send down which is very
confusing.
This bug was introduced in commit d2eb35acfd and so the patch
is suitable for 3.1.x and 3.2.x
Reported-and-tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-and-tested-by: Art -kwaak- van Breemen <ard@telegraafnet.nl>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org
Now that WantReplacement drives are replaced cleanly, mark a drive
as want_replacement when we see a write error. It might get failed soon so
the WantReplacement flag is irrelevant, but if the write error is recorded
in the bad block log, we still want to activate any spare that might
be available.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to add a spare to a RAID1 array, also consider
adding it as a replacement for a want_replacement device.
Signed-off-by: NeilBrown <neilb@suse.de>
If a Replacement is seen, file it as such.
If we see two replacements (or two normal devices) for the one slot,
abort.
Signed-off-by: NeilBrown <neilb@suse.de>
When recovery completes ->spare_active is called.
This checks if the replacement is ready and if so it fails
the original.
Signed-off-by: NeilBrown <neilb@suse.de>
In RAID1, a replacement is much like a normal device, so we just
double the size of the relevant arrays and look at all possible
devices for reads and writes.
This means that the array looks like it is now double the size in some
way - we need to be careful about that.
In particular, we checking if the array is still degraded while
creating a recovery request we need to only consider the first 'half'
- i.e. the real (non-replacement) devices.
Signed-off-by: NeilBrown <neilb@suse.de>
In general mddev->raid_disks can change unexpectedly while
conf->raid_disks will only change in a very controlled way. So change
some uses of one to the other.
The use of mddev->raid_disks will not cause actually problems but
this way is more consistent and safer in the long term.
Signed-off-by: NeilBrown <neilb@suse.de>
Soon an array will be able to have multiple devices with the
same raid_disk number (an original and a replacement). So removing
a device based on the number won't work. So pass the actual device
handle instead.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in md dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In 3.0 we changed the way recovery_disabled was handle so that instead
of testing against zero, we test an mddev-> value against a conf->
value.
Two problems:
1/ one place in raid1 was missed and still sets to '1'.
2/ We didn't explicitly set the conf-> value at array creation
time.
It defaulted to '0' just like the mddev value does so they
could appear equal and thus disable recovery.
This did not affect normal 'md' as it calls bind_rdev_to_array
which changes the mddev value. However the dmraid interface
doesn't call this and so doesn't change ->recovery_disabled; so at
array start all recovery is incorrectly disabled.
So initialise the 'conf' value to one less that the mddev value, so
the will only be the same when explicitly set that way.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
bio originally has the functionality to set the complete cpu, but
it is broken.
Chirstoph said that "This code is unused, and from the all the
discussions lately pretty obviously broken. The only thing keeping
it serves is creating more confusion and possibly more bugs."
And Jens replied with "We can kill bio_set_completion_cpu(). I'm fine
with leaving cpu control to the request based drivers, they are the
only ones that can toggle the setting anyway".
So this patch tries to remove all the work of controling complete cpu
from a bio.
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
RAID1 and RAID10 handle write requests by queuing them for handling by
a separate thread. This is because when a write-intent-bitmap is
active we might need to update the bitmap first, so it is good to
queue a lot of writes, then do one big bitmap update for them all.
However writeback request devices to appear to be congested after a
while so it can make some guesstimate of throughput. The infinite
queue defeats that (note that RAID5 has already has a finite queue so
it doesn't suffer from this problem).
So impose a limit on the number of pending write requests. By default
it is 1024 which seems to be generally suitable. Make it configurable
via module option just in case someone finds a regression.
Signed-off-by: NeilBrown <neilb@suse.de>
The typedefs are just annoying. 'mdk' probably refers to 'md_k.h'
which used to be an include file that defined this thing.
Signed-off-by: NeilBrown <neilb@suse.de>
When normal-write and sync-read/write bio completes, we should
find out the disk number the bio belongs to. Factor those common
code out to a separate function.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Two related problems:
1/ some error paths call "md_unregister_thread(mddev->thread)"
without subsequently clearing ->thread. A subsequent call
to mddev_unlock will try to wake the thread, and crash.
2/ Most calls to md_wakeup_thread are protected against the thread
disappeared either by:
- holding the ->mutex
- having an active request, so something else must be keeping
the array active.
However mddev_unlock calls md_wakeup_thread after dropping the
mutex and without any certainty of an active request, so the
->thread could theoretically disappear.
So we need a spinlock to provide some protections.
So change md_unregister_thread to take a pointer to the thread
pointer, and ensure that it always does the required locking, and
clears the pointer properly.
Reported-by: "Moshe Melnikov" <moshe@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
cc: stable@kernel.org
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
A single request to RAID1 or RAID10 might result in multiple
requests if there are known bad blocks that need to be avoided.
To detect if we need to submit another write request we test:
if (sectors_handled < (bio->bi_size >> 9)) {
However this is after we call **_write_done() so the 'bio' no longer
belongs to us - the writes could have completed and the bio freed.
So move the **_write_done call until after the test against
bio->bi_size.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=41862
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: NeilBrown <neilb@suse.de>
raid1d is too big with several deep branches.
So separate them out into their own functions.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we cannot read a block from anywhere during recovery, there is
now a better approach than just giving up.
We can record a bad block on each device and keep going - being
careful not to clear the bad block when a write succeeds as it might -
it will be a write of incorrect data.
We have now reached the state where - for raid1 - we only call
md_error if md_set_badblocks has failed.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we find a bad block while writing as part of resync/recovery we
need to report that back to raid1d which must record the bad block,
or fail the device.
Similarly when fixing a read error, a further error should just
record a bad block if possible rather than failing the device.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
When we get a write error (in the data area, not in metadata),
update the badblock log rather than failing the whole device.
As the write may well be many blocks, we trying writing each
block individually and only log the ones which fail.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
When performing write-behind we allocate pages to store the data
during write.
Previously we just keep a list of pages. Now we keep a list of
bi_vec which includes offset and size.
This means that the r1bio has complete information to create a new
bio which will be needed for retrying after write errors.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we succeed in writing to a block that was recorded as
being bad, we clear the bad-block record.
This requires some delayed handling as the bad-block-list update has
to happen in process-context.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we have seen any write error on a drive, then don't write to
any known-bad blocks on that drive.
If necessary, we divide the write request up into pieces just
like we do for reads, so each piece is either all written or
all not written to any given drive.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
It is only safe to choose not to write to a bad block if that bad
block is safely recorded in metadata - i.e. if it has been
'acknowledged'.
If it hasn't we need to wait for the acknowledgement.
We support that using rdev->blocked wait and
md_wait_for_blocked_rdev by introducing a new device flag
'BlockedBadBlock'.
This flag is only advisory.
It is cleared whenever we acknowledge a bad block, so that a waiter
can re-check the particular bad blocks that it is interested it.
It should be set by a caller when they find they need to wait.
This (set after test) is inherently racy, but as
md_wait_for_blocked_rdev already has a timeout, losing the race will
have minimal impact.
When we clear "Blocked" was also clear "BlockedBadBlocks" incase it
was set incorrectly (see above race).
We also modify the way we manage 'Blocked' to fit better with the new
handling of 'BlockedBadBlocks' and to make it consistent between
externally managed and internally managed metadata. This requires
that each raidXd loop checks if the metadata needs to be written and
triggers a write (md_check_recovery) if needed. Otherwise a queued
write request might cause raidXd to wait for the metadata to write,
and only that thread can write it.
Before writing metadata, we set FaultRecorded for all devices that
are Faulty, then after writing the metadata we clear Blocked for any
device for which the Fault was certainly Recorded.
The 'faulty' device flag now appears in sysfs if the device is faulty
*or* it has unacknowledged bad blocks. So user-space which does not
understand bad blocks can continue to function correctly.
User space which does, should not assume a device is faulty until it
sees the 'faulty' flag, and then sees the list of unacknowledged bad
blocks is empty.
Signed-off-by: NeilBrown <neilb@suse.de>
When performing resync/etc, keep the size of the request
small enough that it doesn't overlap any known bad blocks.
Devices with badblocks at the start of the request are completely
excluded.
If there is nowhere to read from due to bad blocks, record
a bad block on each target device.
Now that we never read from known-bad-blocks we can allow devices with
known-bad-blocks into a RAID1.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that we have a bad block list, we should not read from those
blocks.
There are several main parts to this:
1/ read_balance needs to check for bad blocks, and return not only
the chosen device, but also how many good blocks are available
there.
2/ fix_read_error needs to avoid trying to read from bad blocks.
3/ read submission must be ready to issue multiple reads to
different devices as different bad blocks on different devices
could mean that a single large read cannot be served by any one
device, but can still be served by the array.
This requires keeping count of the number of outstanding requests
per bio. This count is stored in 'bi_phys_segments'
4/ retrying a read needs to also be ready to submit a smaller read
and queue another request for the rest.
This does not yet handle bad blocks when reading to perform resync,
recovery, or check.
'md_trim_bio' will also be used for RAID10, so put it in md.c and
export it.
Signed-off-by: NeilBrown <neilb@suse.de>
As no personality understand bad block lists yet, we must
reject any device that is known to contain bad blocks.
As the personalities get taught, these tests can be removed.
This only applies to raid1/raid5/raid10.
For linear/raid0/multipath/faulty the whole concept of bad blocks
doesn't mean anything so there is no point adding the checks.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If device-mapper creates a RAID1 array that includes devices to
be rebuilt, it will deref a NULL pointer when finished because
sysfs is not used by device-mapper instantiated RAID devices.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Read errors are considered to corrected if write-back and re-read
cycle is finished without further problems. Thus moving the rdev->
corrected_errors counting after the re-reading looks more reasonable
IMHO. Also included a couple of whitespace fixes on sync_page_io().
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If we hit a read error while recovering a mirror, we want to abort the
recovery without necessarily failing the disk - as having a disk this
a read error is better than not having an array at all.
Currently this is managed with a per-array flag "recovery_disabled"
and is only implemented for RAID1. For RAID10 we will need finer
grained control as we might want to disable recovery for individual
devices separately.
So push more of the decision making into the personality.
'recovery_disabled' is now a 'cookie' which is copied when the
personality want to disable recovery and is changed when a device is
added to the array as this is used as a trigger to 'try recovery
again'.
This will allow RAID10 to get the control that it needs.
Signed-off-by: NeilBrown <neilb@suse.de>
There are places where sysfs links to rdev are handled
in a same way. Add the helper functions to consolidate
them.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
As per printk_ratelimit comment, it should not be used.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1: Changes to allow RAID1 to be used by device-mapper (dm-raid.c)
Added the necessary congestion function and conditionalize calls requiring an
array 'queue' or 'gendisk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The sysfs attribute 'resync_start' (known internally as recovery_cp),
records where a resync is up to. A value of 0 means the array is
not known to be in-sync at all. A value of MaxSector means the array
is believed to be fully in-sync.
When the size of member devices of an array (RAID1,RAID4/5/6) is
increased, the array can be increased to match. This process sets
resync_start to the old end-of-device offset so that the new part of
the array gets resynced.
However with RAID1 (and RAID6) a resync is not technically necessary
and may be undesirable. So it would be good if the implied resync
after the array is resized could be avoided.
So: change 'resync_start' so the value can be changed while the array
is active, and as a precaution only allow it to be changed while
resync/recovery is 'frozen'. Changing it once resync has started is
not going to be useful anyway.
This allows the array to be resized without a resync by:
write 'frozen' to 'sync_action'
write new size to 'component_size' (this will set resync_start)
write 'none' to 'resync_start'
write 'idle' to 'sync_action'.
Also slightly improve some tests on recovery_cp when resizing
raid1/raid5. Now that an arbitrary value could be set we should be
more careful in our tests.
Signed-off-by: NeilBrown <neilb@suse.de>
The current handling and freeing of these pages is a bit fragile.
We only keep the list of allocated pages in each bio, so we need to
still have a valid bio when freeing the pages, which is a bit clumsy.
So simply store the allocated page list in the r1_bio so it can easily
be found and freed when we are finished with the r1_bio.
Signed-off-by: NeilBrown <neilb@suse.de>
If we get a read error during resync/recovery we current repeat with
single-page reads to find out just where the error is, and possibly
read each page from a different device.
With check/repair we don't currently do that, we just fail.
However it is possible that while all devices fail on the large 64K
read, we might be able to satisfy each 4K from one device or another.
So call fix_sync_read_error before process_checks to maximise the
chance of finding good data and writing it out to the devices with
read errors.
For this to work, we need to set the 'uptodate' flags properly after
fix_sync_read_error has succeeded.
Signed-off-by: NeilBrown <neilb@suse.de>
These changes are mostly cosmetic:
1/ change mddev->raid_disks to conf->raid_disks because the later is
technically safer, though in current practice it doesn't matter in
this particular context.
2/ Rearrange two for / if loops to have an early 'continue' so the
body of the 'if' doesn't need to be indented so much.
Signed-off-by: NeilBrown <neilb@suse.de>
sync_request_write is too big and too deep.
So split out two self-contains bits of functionality into separate
function.
Signed-off-by: NeilBrown <neilb@suse.de>
read_balance has two loops which both look for a 'best'
device based on slightly different criteria.
This is clumsy and makes is hard to add extra criteria.
So replace it all with a single loop that combines everything.
Signed-off-by: NeilBrown <neilb@suse.de>
We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.
Also remove some plug-related code that is no longer needed.
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid submits a lot of IO from the various raid threads.
So adding start/finish plug calls to those so that some
plugging happens.
Signed-off-by: NeilBrown <neilb@suse.de>
MD and DM create a new bio_set for every metadevice. Each bio_set has an
integrity mempool attached regardless of whether the metadevice is
capable of passing integrity metadata. This is a waste of memory.
Instead we defer the allocation decision to MD and DM since we know at
metadevice creation time whether integrity passthrough is needed or not.
Automatic integrity mempool allocation can then be removed from
bioset_create() and we make an explicit integrity allocation for the
fs_bio_set.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Acked-by: Mike Snitzer <snizer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
blk_throtl_exit assumes that ->queue_lock still exists,
so make sure that it does.
To do this, we stop redirecting ->queue_lock to conf->device_lock
and leave it pointing where it is initialised - __queue_lock.
As the blk_plug functions check the ->queue_lock is held, we now
take that spin_lock explicitly around the plug functions. We don't
need the locking, just the warning removal.
This is needed for any kernel with the blk_throtl code, which is
which is 2.6.37 and later.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Add new parameter to 'sync_page_io'.
The new parameter allows us to distinguish between metadata and data
operations. This becomes important later when we add the ability to
use separate devices for data and metadata.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Commit 4044ba58dd supposedly fixed a
problem where if a raid1 with just one good device gets a read-error
during recovery, the recovery would abort and immediately restart in
an infinite loop.
However it depended on raid1_remove_disk removing the spare device
from the array. But that does not happen in this case. So add a test
so that in the 'recovery_disabled' case, the device will be removed.
This suitable for any kernel since 2.6.29 which is when
recovery_disabled was introduced.
Cc: stable@kernel.org
Reported-by: Sebastian Färber <faerber@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The code for searching through the device list to read-balance in
raid1 is rather clumsy and hard to follow. Try to simplify it a bit.
No important functionality change here.
Signed-off-by: NeilBrown <neilb@suse.de>
bio_clone and bio_alloc allocate from a common bio pool.
If an md device is stacked with other devices that use this pool, or under
something like swap which uses the pool, then the multiple calls on
the pool can cause deadlocks.
So allocate a local bio pool for each md array and use that rather
than the common pool.
This pool is used both for regular IO and metadata updates.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently sync_page_io takes a 'bdev'.
Every caller passes 'rdev->bdev'.
We will soon want another field out of the rdev in sync_page_io,
So just pass the rdev instead of the bdev out of it.
Signed-off-by: NeilBrown <neilb@suse.de>
Though this mem alloc is GFP_NOIO an so will not deadlock, it seems
better to do the allocation before 'raise_barrier' which stops any IO
requests while the resync proceeds.
raid10 always uses this order, so it is at least consistent to do the
same in raid1.
Signed-off-by: NeilBrown <neilb@suse.de>
bio_alloc can never fail (as it uses a mempool) but an block
indefinitely, especially if the caller is holding a reference to a
previously allocated bio.
So these to places which both handle failure and hold multiple bios
should not use bio_alloc, they should use bio_kmalloc.
Signed-off-by: NeilBrown <neilb@suse.de>
It is not safe to allocate from a mempool while holding an item
previously allocated from that mempool as that can deadlock when the
mempool is close to exhaustion.
So don't use a bio list to collect the bios to write to multiple
devices in raid1 and raid10.
Instead queue each bio as it becomes available so an unplug will
activate all previously allocated bios and so a new bio has a chance
of being allocated.
This means we must set the 'remaining' count to '1' before submitting
any requests, then when all are submitted, decrement 'remaining' and
possible handle the write completion at that point.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_get_counter returns the number of sectors covered
by the counter in a pass-by-reference variable.
In some cases this can be very large, so make it a sector_t
for safety.
Signed-off-by: NeilBrown <neilb@suse.de>
When performing a resync we pre-allocate some bios and repeatedly use
them. This requires us to re-initialise them each time.
One field (bi_comp_cpu) and some flags weren't being initiaised
reliably.
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_start_sync returns - via a pass-by-reference variable - the
number of sectors before we need to check with the bitmap again.
Since commit ef42567335 this number can be substantially larger,
2^27 is a common value.
Unfortunately it is an 'int' and so when raid1.c:sync_request shifts
it 9 places to the left it becomes 0. This results in a zero-length
read which the scsi layer justifiably complains about.
This patch just removes the shift so the common case becomes safe with
a trivially-correct patch.
In the next merge window we will convert this 'int' to a 'sector_t'
Reported-by: "George Spelvin" <linux@horizon.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch converts md to support REQ_FLUSH/FUA instead of now
deprecated REQ_HARDBARRIER. In the core part (md.c), the following
changes are notable.
* Unlike REQ_HARDBARRIER, REQ_FLUSH/FUA don't interfere with
processing of other requests and thus there is no reason to mark the
queue congested while FLUSH/FUA is in progress.
* REQ_FLUSH/FUA failures are final and its users don't need retry
logic. Retry logic is removed.
* Preflush needs to be issued to all member devices but FUA writes can
be handled the same way as other writes - their processing can be
deferred to request_queue of member devices. md_barrier_request()
is renamed to md_flush_request() and simplified accordingly.
For linear, raid0 and multipath, the core changes are enough. raid1,
5 and 10 need the following conversions.
* raid1: Handling of FLUSH/FUA bio's can simply be deferred to
request_queues of member devices. Barrier related logic removed.
* raid5: Queue draining logic dropped. FUA bit is propagated through
biodrain and stripe resconstruction such that all the updated parts
of the stripe are written out with FUA writes if any of the dirtying
writes was FUA. preread_active_stripes handling in make_request()
is updated as suggested by Neil Brown.
* raid10: FUA bit needs to be propagated to write clones.
linear, raid0, 1, 5 and 10 tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
commit 7b6d91daee changed the behaviour
of a few variables in raid1 and raid10 from flags to bit-sets, but
left them as type 'bool' so they did not work.
Change them (back) to unsigned long.
(historical note: see 1ef04fefe2)
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Jiri Slaby <jslaby@suse.cz> and many others
md_check_recovery expects ->spare_active to return 'true' if any
spares were activated, but none of them do, so the consequent change
in 'degraded' is not notified through sysfs.
So count the number of spares activated, subtract it from 'degraded'
just once, and return it.
Reported-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When RAID1 is done syncing disks, it'll update the state
of synced rdevs to In_sync. But it neglected to notify
sysfs that the attribute changed. So any programs that
are waiting for an rdev's state to change will not be
woken.
(raid5/raid10 added by neilb)
Signed-off-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Conflicts:
drivers/md/md.c
- Resolved conflict in md_update_sb
- Added extra 'NULL' arg to new instance of sysfs_get_dirent.
Signed-off-by: NeilBrown <neilb@suse.de>
read_balance uses a "unsigned long" for a sector number which
will get truncated beyond 2TB.
This will cause read-balancing to be non-optimal, and can cause
data to be read from the 'wrong' branch during a resync. This has a
very small chance of returning wrong data.
Reported-by: Jordan Russell <jr-list-2010@quo.to>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a raid1 array is configured to support write-behind
on some devices, it normally only reads from other devices.
If all devices are write-behind (because the rest have failed)
it is possible for a read request to be serviced before a
behind-write request, which would appear as data corruption.
So when forced to read from a WriteMostly device, wait for any
write-behind to complete, and don't start any more behind-writes.
Signed-off-by: NeilBrown <neilb@suse.de>
This message seems to suggest the named device is the one on which a
read failed, however it is actually the device that the read will be
redirected to.
So make the message a little clearer.
Reported-by: Tim Burgess <ozburgess@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We used to pass the personality make_request function direct
to the block layer so the first argument had to be a queue.
But now we have the intermediary md_make_request so it makes
at lot more sense to pass a struct mddev_s.
It makes it possible to have an mddev without its own queue too.
Signed-off-by: NeilBrown <neilb@suse.de>
We set ->changed to 1 and call check_disk_change at the end
of md_open so that bd_invalidated would be set and thus
partition rescan would happen appropriately.
Now that we call revalidate_disk directly, which sets bd_invalidates,
that indirection is no longer needed and can be removed.
Signed-off-by: NeilBrown <neilb@suse.de>
While I generally prefer letting personalities do as much as possible,
given that we have a central md_make_request anyway we may as well use
it to simplify code.
Also this centralises knowledge of ->gendisk which will help later.
Signed-off-by: NeilBrown <neilb@suse.de>
void pointers do not need to be cast to other pointer types.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There is a very small race window when writing to a
RAID1 such that if a device is marked faulty at exactly the wrong
time, the write-in-progress will not be sent to the device,
but the bitmap (if present) will be updated to say that
the write was sent.
Then if the device turned out to still be usable as was re-added
to the array, the bitmap-based-resync would skip resyncing that
block, possibly leading to corruption. This would only be a problem
if no further writes were issued to that area of the device (i.e.
that bitmap chunk).
Suitable for any pending -stable kernel.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
If a component device has a merge_bvec_fn then as we never call it
we must ensure we never need to. Currently this is done by setting
max_sector to 1 PAGE, however this does not stop a bio being created
with several sub-page iovecs that would violate the merge_bvec_fn.
So instead set max_segments to 1 and set the segment boundary to the
same as a page boundary to ensure there is only ever one single-page
segment of IO requested at a time.
This can particularly be an issue when 'xen' is used as it is
known to submit multiple small buffers in a single bio.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
... and into bitmap_info. These are all configuration parameters
that need to be set before the bitmap is created.
Signed-off-by: NeilBrown <neilb@suse.de>
This will allow us to stop writeout to portions of the array
while they are resynced by someone else - e.g. another node in
a cluster.
Signed-off-by: NeilBrown <neilb@suse.de>
commit 4706b349f was a forward port of a fix that was needed
for SLES10. But in fact it is not needed in mainline because
the earlier commit dd00a99e7a fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction. If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.
After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Both raid1 and raid10 create a mempool during startup.
If the 'alloc' function for this mempool fails, unplug_slaves
is called.
If that happens when the pool is being initialised, unplug_slaves
will try to use the 'conf' structure that isn't filled in yet, and
badness will happen.
So ensure that unplug_slaves doesn't get called unless we know
that the conf structure if fully initialised.
Signed-off-by: NeilBrown <neilb@suse.de>
During 'check' of a raid1 or raid10 it is possible for the management
thread to spend a lot of time running 'memcmp' on blocks from
different devices, so make sure the thread has a chance to schedule.
raid5d already has a cond_resched (in process_stripe).
Reported-By: Lee Howard <faxguy@howardsilvan.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Recently Jens has changed bio_rw_flagged() logic by following
commit 1f98a13f62. Now it returns
bool instead of int. This broke raid1/raid10 RW bits manipulation logic.
One of visible result is BUG_ON triggering due to empty barrier
here scsi_lib.c:1108 scsi_setup_fs_cmnd()
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The management thread for raid4,5,6 arrays are all called
mdX_raid5, independent of the actual raid level, which is wrong and
can be confusion.
So change md_register_thread to use the name from the personality
unless no alternate name (like 'resync' or 'reshape') is given.
This is simpler and more correct.
Cc: Jinzc <zhenchengjin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Get rid of any functions that test for these bits and make callers
use bio_rw_flagged() directly. Then it is at least directly apparent
what variable and flag they check.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode. So use that instead of mucking about with locks and
i_size_write.
Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.
Signed-off-by: NeilBrown <neilb@suse.de>
Jens Axboe
Christoph Hellwig
Goldwyn Rodrigues
NeilBrown
Tejun Heo
NeilBrown
Tomáš Hodek
Nate Dailey
Linus Torvalds
Kent Overstreet
majianpeng
Lukasz Dorau
Jonathan Brassow
H. Peter Anvin
Alex Lyakas
Shaohua Li
Hirokazu Takahashi
Kent Overstreet
Joe Lawrence
Lukas Czerner
Shaohua Li
Alexander Lyakas
Paul Gortmaker
Tao Ma
Jens Axboe
Namhyung Kim
Christoph Hellwig
Christian Dietrich
Martin K. Petersen
Jens Axboe
Joe Perches
Adrian Drzewiecki
H Hartley Sweeten
Dmitry Monakhov
Jens Axboe