WMM IE QoS Info field lower 4 bits: Parameter Set Count
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a field to wiphy for the hardware to report the availble antennas for
configuration. Only if this is set to something bigger than zero, will the
anntenna configuration ops be executed.
Allthough this could be a simple number of antennas, I defined it as a bitmap
of antennas which are available for configuration, since it's more consistent
with the rest of the antenna API and there could be cases where the
hardware allows only configuration of certain antennas. As it does not make
much of a difference in size or normal usage, I think it's better to be able to
support this, in case the need arises.
The antenna configuration is now also checked against the availabe antennas and
rejected if it does not match.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v3: always apply available antenna mask (for "all" antennas case).
v2: reject antenna configurations which don't match the available antennas
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using bitshifts instead of division and multiplication should improve
performance. That requires weight and factor to be powers of two, but i think
this is something we can live with.
Thanks to Peter Zijlstra for the improved formula!
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v2: use log2.h functions
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch with the same title was for mac80211 ops, accidentally.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove extra spaces from legal text so that legal stuff looks
the same for all bluetooth code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Do not use assignment in IF condition, remove extra spaces,
fixing typos, simplify code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Do not initialize static vars to zero, macros with complex values
shall be enclosed with (), remove unneeded braces.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Remove extra spaces, assignments in if statement, zeroing static
variables, extra braces. Fix includes.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Do not use assignments in IF condition, remove extra spaces
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.
To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone(). For the rt2800pci special case a driver
flag is introduced.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.
We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.
This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.
Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.
This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:
#!/bin/bash
echo $COUNTRY >> /tmp/log
sleep 2
/sbin/crda.orig
And these regulatory tests:
modprobe mac80211_hwsim regtest=2
modprobe mac80211_hwsim regtest=3
Reported-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new vendor for Broadcom 4318.
Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds generic functions for calculating Exponentially Weighted Moving
Averages (EWMA). This implementation makes use of a structure which keeps the
EWMA parameters and a scaled up internal representation to reduce rounding
errors.
The original idea for this implementation came from the rt2x00 driver
(rt2x00link.c). I would like to use it in several places in the mac80211 and
ath5k code and I hope it can be useful in many other places in the kernel code.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In many places we've just hardcoded the
AC numbers -- which is a relic from the
original mac80211 (d80211). Add constants
for them so we know what we're talking
about.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chipsets with hardware based connection monitoring need to autonomically
send directed probe-request frames to the AP (in the event of beacon loss,
for example.)
For the hardware to be able to do this, it requires a template for the frame
to transmit to the AP, filled in with the BSSID and SSID of the AP, but also
the supported rate IE's.
This patch adds a function to mac80211, which allows the hardware driver to
fetch this template after association, so it can be configured to the hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow antenna configuration by calling driver's function for it.
We disallow antenna configuration if the wiphy is already running, mainly to
make life easier for 802.11n drivers which need to recalculate HT capabilites.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WIPHY_FLAG_IBSS_RSN is BIT(7) as is WIPHY_FLAG_CONTROL_PORT_PROTOCOL. Change
to BIT(8).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When b43legacy is compiled on the arm platform, the following errors are seen:
CC [M] drivers/net/wireless/b43legacy/xmit.o
In file included from include/net/dst.h:11,
from drivers/net/wireless/b43legacy/xmit.c:31:
include/net/dst_ops.h:28: error: expected ':', ',', ';', '}' or '__attribute__'
before '____cacheline_aligned_in_smp'
include/net/dst_ops.h: In function 'dst_entries_get_fast':
include/net/dst_ops.h:33: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_get_slow':
include/net/dst_ops.h:41: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_add':
include/net/dst_ops.h:49: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_init':
include/net/dst_ops.h:55: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_destroy':
include/net/dst_ops.h:60: error: 'struct dst_ops' has no member named
'pcpuc_entries'
make[4]: *** [drivers/net/wireless/b43legacy/xmit.o] Error 1
make[3]: *** [drivers/net/wireless/b43legacy] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
The cause is a missing include of <linux/cache.h>, which is present for
i386 and x86_64 architectures, but not for arm.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a module loads you will have loaded the world roaming regulatory
domain or a custom regulatory domain. Further regulatory hints are
welcomed and should be respected unless the regulatory hint is coming
from a country IE as the IEEE spec allows for a country IE to be a subset
of what is allowed by the local regulatory agencies.
So disable all channels that do not fit a regulatory domain sent
from a unless the hint is from a country IE and the country IE had
no information about the band we are currently processing.
This fixes a few regulatory issues, for example for drivers that depend
on CRDA and had no 5 GHz freqencies allowed were not properly disabling
5 GHz at all, furthermore it also allows users to restrict devices
further as was intended.
If you recieve a country IE upon association we will also disable the
channels that are not allowed if the country IE had at least one
channel on the respective band we are procesing.
This was the original intention behind this design but it was
completely overlooked...
Cc: David Quan <david.quan@atheros.com>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.
This was part of the original design, however it was completely
overlooked...
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following code is defined but never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: fix erroneous platform data in U300
spi: fixed odd static string conventions in core code
spi/bfin_spi: only request GPIO on first load
spi/bfin_spi: handle error/status changes after data interrupts
spi: enable spi_board_info to be registered after spi_master
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-i801: Add PCI idents for Patsburg 'IDF' SMBus controllers
i2c-i801: Handle multiple instances instead of keeping global state
i2c-i801: Add Intel Patsburg device ID
i2c: Drop unused I2C_CLASS_TV flags
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (70 commits)
[SCSI] pmcraid: add support for set timestamp command and other fixes
[SCSI] pmcraid: remove duplicate struct member
[SCSI] qla4xxx: Fix cmd check in qla4xxx_cmd_wait
[SCSI] megaraid_sas: Version and documentation update
[SCSI] megaraid_sas: Add three times Online controller reset
[SCSI] megaraid_sas: Add input parameter for max_sectors
[SCSI] megaraid_sas: support devices update flag
[SCSI] libosd: write/read_sg_kern API
[SCSI] libosd: Support for scatter gather write/read commands
[SCSI] libosd: Free resources in reverse order of allocation
[SCSI] libosd: Fix bug in attr_page handling
[SCSI] lpfc 8.3.18: Update lpfc driver version to 8.3.18
[SCSI] lpfc 8.3.18: Add new WQE support
[SCSI] lpfc 8.3.18: Fix critical errors
[SCSI] lpfc 8.3.18: Adapter Shutdown and Unregistration cleanup
[SCSI] lpfc 8.3.18: Add logic to detect last devloss timeout
[SCSI] lpfc 8.3.18: Add support of received ELS commands
[SCSI] lpfc 8.3.18: FC/FCoE Discovery fixes
[SCSI] ipr: add definitions for a new adapter
[SCSI] bfa: fix comments for c files
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix up irq_node() for irq_data changes.
genirq: Add single IRQ reservation helper
genirq: Warn if enable_irq is called before irq is set up
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
semaphore: Remove mutex emulation
staging: Final semaphore cleanup
jbd2: Convert jbd2_slab_create_sem to mutex
hpfs: Convert sbi->hpfs_creation_de to mutex
Fix up trivial change/delete conflicts with deleted 'dream' drivers
(drivers/staging/dream/camera/{mt9d112.c,mt9p012_fox.c,mt9t013.c,s5k3e2fx.c})
Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This one was only used for a nasty hack in nfsd, which has recently
been removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bing Zhao
Johannes Berg
Bruno Randolf
Amitkumar Karwar
Helmut Schaa
Javier Cardona
John W. Linville
Rafał Miłecki
Andrei Emeltchenko
Johannes Stezenbach
Felix Fietkau
Luis R. Rodriguez
Daniel Klaffenbach
Juuso Oikarinen
Arik Nemtsov
Jussi Kivilinna
Arnd Hannemann
Andreas Herrmann
Gery Kahn
Stephen Hemminger
Linus Torvalds
Seth Heasley
Jean Delvare
Christoph Hellwig