f2fs_hw_support_discard() only tests if the super block device supports
discard. However, for a multi-device volume, not all disks used may
support discard. Improve the check performed to test all devices of
the volume and report discard as supported if at least one device of
the volume supports discard. To implement this, introduce the helper
function f2fs_bdev_support_discard(), which returns true for zoned block
devices (where discard is processed as a zone reset) and for regular
disks supporting the discard command.
f2fs_bdev_support_discard() is also used in __queue_discard_cmd() to
handle discard command issuing for a particular device of the volume.
That is, prevent issuing a discard command for block devices that do
not support it.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For zoned block devices, an array of zone types for each device is
allocated and initialized in order to determine if a section is stored
on a sequential zone (zone reset needed) or a conventional zone (no
zone reset needed and regular discard applies). Considering this usage,
the zone types stored in memory can be replaced with a bitmap to
indicate an equivalent information, that is, if a zone is sequential or
not. This reduces the memory usage for each zoned device by roughly 8:
on a 14TB disk with zones of 256 MB, the zone type array consumes
13x4KB pages while the bitmap uses only 2x4KB pages.
This patch changes the f2fs_dev_info structure blkz_type field to the
bitmap blkz_seq. Access to this bitmap is done using the helper
function f2fs_blkz_is_seq(), which is a rewrite of the function
get_blkz_type().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For a single device mount using a zoned block device, the zone
information for the device is stored in the sbi->devs single entry
array and sbi->s_ndevs is set to 1. This differs from a single device
mount using a regular block device which does not allocate sbi->devs
and sets sbi->s_ndevs to 0.
However, sbi->s_devs == 0 condition is used throughout the code to
differentiate a single device mount from a multi-device mount where
sbi->s_ndevs is always larger than 1. This results in problems with
single zoned block device volumes as these are treated as multi-device
mounts but do not have the start_blk and end_blk information set. One
of the problem observed is skipping of zone discard issuing resulting in
write commands being issued to full zones or unaligned to a zone write
pointer.
Fix this problem by simply treating the cases sbi->s_ndevs == 0 (single
regular block device mount) and sbi->s_ndevs == 1 (single zoned block
device mount) in the same manner. This is done by introducing the
helper function f2fs_is_multi_device() and using this helper in place
of direct tests of sbi->s_ndevs value, improving code readability.
Fixes: 7bb3a371d1 ("f2fs: Fix zoned block device support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We've continued mainly to fix bugs in this round, as f2fs has been shipped
in more devices. Especially, we've focused on stabilizing checkpoint=disable
feature, and provided some interfaces for QA.
Enhancement:
- expose FS_NOCOW_FL for pin_file
- run discard jobs at unmount time with timeout
- tune discarding thread to avoid idling which consumes power
- some checking codes to address vulnerabilities
- give random value to i_generation
- shutdown with more flags for QA
Bug fix:
- clean up stale objects when mount is failed along with checkpoint=disable
- fix system being stuck due to wrong count by atomic writes
- handle some corrupted disk cases
- fix a deadlock in f2fs_read_inline_dir
We've also added some minor build errors and clean-up patches.
-----BEGIN PGP SIGNATURE-----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=9BoH
-----END PGP SIGNATURE-----
Merge tag 'f2fs-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"We've continued mainly to fix bugs in this round, as f2fs has been
shipped in more devices. Especially, we've focused on stabilizing
checkpoint=disable feature, and provided some interfaces for QA.
Enhancements:
- expose FS_NOCOW_FL for pin_file
- run discard jobs at unmount time with timeout
- tune discarding thread to avoid idling which consumes power
- some checking codes to address vulnerabilities
- give random value to i_generation
- shutdown with more flags for QA
Bug fixes:
- clean up stale objects when mount is failed along with
checkpoint=disable
- fix system being stuck due to wrong count by atomic writes
- handle some corrupted disk cases
- fix a deadlock in f2fs_read_inline_dir
We've also added some minor build error fixes and clean-up patches"
* tag 'f2fs-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (53 commits)
f2fs: set pin_file under CAP_SYS_ADMIN
f2fs: fix to avoid deadlock in f2fs_read_inline_dir()
f2fs: fix to adapt small inline xattr space in __find_inline_xattr()
f2fs: fix to do sanity check with inode.i_inline_xattr_size
f2fs: give some messages for inline_xattr_size
f2fs: don't trigger read IO for beyond EOF page
f2fs: fix to add refcount once page is tagged PG_private
f2fs: remove wrong comment in f2fs_invalidate_page()
f2fs: fix to use kvfree instead of kzfree
f2fs: print more parameters in trace_f2fs_map_blocks
f2fs: trace f2fs_ioc_shutdown
f2fs: fix to avoid deadlock of atomic file operations
f2fs: fix to dirty inode for i_mode recovery
f2fs: give random value to i_generation
f2fs: no need to take page lock in readdir
f2fs: fix to update iostat correctly in IPU path
f2fs: fix encrypted page memory leak
f2fs: make fault injection covering __submit_flush_wait()
f2fs: fix to retry fill_super only if recovery failed
f2fs: silence VM_WARN_ON_ONCE in mempool_alloc
...
As Gao Xiang reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=202749
f2fs may skip pageout() due to incorrect page reference count.
The problem here is that MM defined the rule [1] very clearly that
once page was set with PG_private flag, we should increment the
refcount in that page, also main flows like pageout(), migrate_page()
will assume there is one additional page reference count if
page_has_private() returns true.
But currently, f2fs won't add/del refcount when changing PG_private
flag. Anyway, f2fs should follow MM's rule to make MM's related flows
running as expected.
[1] https://lore.kernel.org/lkml/2b19b3c4-2bc4-15fa-15cc-27a13e5c7af1@aol.com/
Reported-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This follows to give random number to i_generation along with commit
2325306802 ("ext4: improve smp scalability for inode generation")
This can be used for DUN for UFS HW encryption.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
First: Ted, Jaegeuk, and I have decided to add me as a co-maintainer for
fscrypt, and we're now using a shared git tree. So we've updated
MAINTAINERS accordingly, and I'm doing the pull request this time.
The actual changes for v5.1 are:
- Remove the fs-specific kconfig options like CONFIG_EXT4_ENCRYPTION and
make fscrypt support for all fscrypt-capable filesystems be controlled
by CONFIG_FS_ENCRYPTION, similar to how CONFIG_QUOTA works.
- Improve error code for rename() and link() into encrypted directories.
- Various cleanups.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCXH2YDRQcZWJpZ2dlcnNA
Z29vZ2xlLmNvbQAKCRDzXCl4vpKOK+SAAQCWYOTwYko8uE8Ze8i2fiUm0vr91NOg
zj5DGmK7Izxy/gEAsNDOVA7zWrDg/f5600/7aLpDQQTGHA38YVsgiyd7DgY=
=S3tT
-----END PGP SIGNATURE-----
Merge tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt
Pull fscrypt updates from Eric Biggers:
"First: Ted, Jaegeuk, and I have decided to add me as a co-maintainer
for fscrypt, and we're now using a shared git tree. So we've updated
MAINTAINERS accordingly, and I'm doing the pull request this time.
The actual changes for v5.1 are:
- Remove the fs-specific kconfig options like CONFIG_EXT4_ENCRYPTION
and make fscrypt support for all fscrypt-capable filesystems be
controlled by CONFIG_FS_ENCRYPTION, similar to how CONFIG_QUOTA
works.
- Improve error code for rename() and link() into encrypted
directories.
- Various cleanups"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
MAINTAINERS: add Eric Biggers as an fscrypt maintainer
fscrypt: return -EXDEV for incompatible rename or link into encrypted dir
fscrypt: remove filesystem specific build config option
f2fs: use IS_ENCRYPTED() to check encryption status
ext4: use IS_ENCRYPTED() to check encryption status
fscrypt: remove CRYPTO_CTR dependency
We use below condition to check inline_xattr_size boundary:
if (!F2FS_OPTION(sbi).inline_xattr_size ||
F2FS_OPTION(sbi).inline_xattr_size >=
DEF_ADDRS_PER_INODE -
F2FS_TOTAL_EXTRA_ATTR_SIZE -
DEF_INLINE_RESERVED_SIZE -
DEF_MIN_INLINE_SIZE)
There is there problems in that check:
- we should allow inline_xattr_size equaling to min size of inline
{data,dentry} area.
- F2FS_TOTAL_EXTRA_ATTR_SIZE and inline_xattr_size are based on
different size unit, previous one is 4 bytes, latter one is 1 bytes.
- DEF_MIN_INLINE_SIZE only indicate min size of inline data area,
however, we need to consider min size of inline dentry area as well,
minimal inline dentry should at least contain two entries: '.' and
'..', so that min inline_dentry size is 40 bytes.
.bitmap 1 * 1 = 1
.reserved 1 * 1 = 1
.dentry 11 * 2 = 22
.filename 8 * 2 = 16
total 40
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Previously, we changed lock from cp_rwsem to node_change, it solved
the deadlock issue which was caused by below race condition:
Thread A Thread B
- f2fs_setattr
- f2fs_lock_op -- read_lock
- dquot_transfer
- __dquot_transfer
- dquot_acquire
- commit_dqblk
- f2fs_quota_write
- f2fs_write_begin
- f2fs_write_failed
- write_checkpoint
- block_operations
- f2fs_lock_all -- write_lock
- f2fs_truncate_blocks
- f2fs_lock_op -- read_lock
But it breaks the sematics of cp_rwsem, in other callers like:
- f2fs_file_write_iter -> f2fs_write_begin -> f2fs_write_failed
- f2fs_direct_IO -> f2fs_write_failed
We allow to truncate dnode w/o cp_rwsem held, result in incorrect sit
bitmap update, which can cause further data corruption.
So this patch reverts previous fix implementation, and try to fix
deadlock by skipping calling f2fs_truncate_blocks() in f2fs_write_failed()
only for quota file, and keep the preallocated data/node in the tail of
quota file, we can expecte that the preallocated space can be used to
store quota info latter soon.
Fixes: af033b2aa8 ("f2fs: guarantee journalled quota data by checkpoint")
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This mode returns mount() quickly with EAGAIN. We can trigger this by
shutdown(F2FS_GOING_DOWN_NEED_FSCK).
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When we umount f2fs, we need to avoid long delay due to discard commands, which
is actually taking tens of seconds, if storage is very slow on UNMAP. So, this
patch introduces timeout-based work on it.
By default, let me give 5 seconds for discard.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In order to have a common code base for fscrypt "post read" processing
for all filesystems which support encryption, this commit removes
filesystem specific build config option (e.g. CONFIG_EXT4_FS_ENCRYPTION)
and replaces it with a build option (i.e. CONFIG_FS_ENCRYPTION) whose
value affects all the filesystems making use of fscrypt.
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
This commit removes the f2fs specific f2fs_encrypted_inode() and makes
use of the generic IS_ENCRYPTED() macro to check for the encryption
status of an inode.
Acked-by: Chao Yu <yuchao0@huawei.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
In order to record direct IO count, we add two additional type in
enum count_type: F2FS_DIO_{WRITE,READ}, but those IO won't dirty
filesystem metadata, so we don't need to set filesystem dirty in
inc_page_count(), fix it.
Fixes: 02b16d0a34 ("f2fs: add to account direct IO")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Cc: linux-f2fs-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Chao Yu <yuchao0@huawei.com>
Cc: linux-f2fs-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For all ordered cases in f2fs_wait_on_page_writeback(), we need to
check PageWriteback status, so let's clean up to relocate the check
into f2fs_wait_on_page_writeback().
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The union in struct extent_node wass only to indicate below fields
struct rb_node rb_node;
union {
struct {
unsigned int fofs;
unsigned int len;
...
...
can be parsed as fields in struct rb_entry, but they were never be
used explicitly before, so let's remove them for cleanup.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When there is a failure in f2fs_fill_super() after/during
the recovery of fsync'd nodes, it frees the current sbi and
retries again. This time the mount is successful, but the files
that got recovered before retry, still holds the extent tree,
whose extent nodes list is corrupted since sbi and sbi->extent_list
is freed up. The list_del corruption issue is observed when the
file system is getting unmounted and when those recoverd files extent
node is being freed up in the below context.
list_del corruption. prev->next should be fffffff1e1ef5480, but was (null)
<...>
kernel BUG at kernel/msm-4.14/lib/list_debug.c:53!
lr : __list_del_entry_valid+0x94/0xb4
pc : __list_del_entry_valid+0x94/0xb4
<...>
Call trace:
__list_del_entry_valid+0x94/0xb4
__release_extent_node+0xb0/0x114
__free_extent_tree+0x58/0x7c
f2fs_shrink_extent_tree+0xdc/0x3b0
f2fs_leave_shrinker+0x28/0x7c
f2fs_put_super+0xfc/0x1e0
generic_shutdown_super+0x70/0xf4
kill_block_super+0x2c/0x5c
kill_f2fs_super+0x44/0x50
deactivate_locked_super+0x60/0x8c
deactivate_super+0x68/0x74
cleanup_mnt+0x40/0x78
__cleanup_mnt+0x1c/0x28
task_work_run+0x48/0xd0
do_notify_resume+0x678/0xe98
work_pending+0x8/0x14
Fix this by not creating extents for those recovered files if shrinker is
not registered yet. Once mount is successful and shrinker is registered,
those files can have extents again.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
One report says memalloc failure during mount.
(unwind_backtrace) from [<c010cd4c>] (show_stack+0x10/0x14)
(show_stack) from [<c049c6b8>] (dump_stack+0x8c/0xa0)
(dump_stack) from [<c024fcf0>] (warn_alloc+0xc4/0x160)
(warn_alloc) from [<c0250218>] (__alloc_pages_nodemask+0x3f4/0x10d0)
(__alloc_pages_nodemask) from [<c0270450>] (kmalloc_order_trace+0x2c/0x120)
(kmalloc_order_trace) from [<c03fa748>] (build_node_manager+0x35c/0x688)
(build_node_manager) from [<c03de494>] (f2fs_fill_super+0xf0c/0x16cc)
(f2fs_fill_super) from [<c02a5864>] (mount_bdev+0x15c/0x188)
(mount_bdev) from [<c03da624>] (f2fs_mount+0x18/0x20)
(f2fs_mount) from [<c02a68b8>] (mount_fs+0x158/0x19c)
(mount_fs) from [<c02c3c9c>] (vfs_kern_mount+0x78/0x134)
(vfs_kern_mount) from [<c02c76ac>] (do_mount+0x474/0xca4)
(do_mount) from [<c02c8264>] (SyS_mount+0x94/0xbc)
(SyS_mount) from [<c0108180>] (ret_fast_syscall+0x0/0x48)
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Commit 089842de ("f2fs: remove codes of unused wio_mutex") removes codes
of unused wio_mutex, but missing the comment, so delete it.
Signed-off-by: Yunlong Song <yunlong.song@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This adds an option in ioctl(F2FS_IOC_SHUTDOWN) in order to trigger fsck by
setting a NEED_FSCK flag.
Generally, shutdown is used for the test to validate filesystem consistency, and
setting NEED_FSCK flag can be used for Android to trigger fsck.f2fs at boot time
explicitly so that we could measure the elapsed time as well as force filesystem
check.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If we want to re-enable nat_bits, we rely on fsck which requires full scan
of directory tree. Let's do that by regular fsck or unclean shutdown.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
After merging the f2fs tree, today's linux-next build
(x86_64_allmodconfig) produced this warning:
In file included from fs/f2fs/dir.c:11:
fs/f2fs/f2fs.h: In function '__mark_inode_dirty_flag':
fs/f2fs/f2fs.h:2388:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (set)
^
fs/f2fs/f2fs.h:2390:2: note: here
case FI_DATA_EXIST:
^~~~
Exposed by my use of -Wimplicit-fallthrough
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In get_more_blocks(), we may override @create as below code:
create = dio->op == REQ_OP_WRITE;
if (dio->flags & DIO_SKIP_HOLES) {
if (fs_startblk <= ((i_size_read(dio->inode) - 1) >>
i_blkbits))
create = 0;
}
But in f2fs_map_blocks(), we only trigger f2fs_balance_fs() if @create
is 1, so in LFS mode, dio overwrite under LFS mode can easily run out
of free segments, result in below panic.
Call Trace:
allocate_segment_by_default+0xa8/0x270 [f2fs]
f2fs_allocate_data_block+0x1ea/0x5c0 [f2fs]
__allocate_data_block+0x306/0x480 [f2fs]
f2fs_map_blocks+0x6f6/0x920 [f2fs]
__get_data_block+0x4f/0xb0 [f2fs]
get_data_block_dio_write+0x50/0x60 [f2fs]
do_blockdev_direct_IO+0xcd5/0x21e0
__blockdev_direct_IO+0x3a/0x3c
f2fs_direct_IO+0x1ff/0x4a0 [f2fs]
generic_file_direct_write+0xd9/0x160
__generic_file_write_iter+0xbb/0x1e0
f2fs_file_write_iter+0xaf/0x220 [f2fs]
__vfs_write+0xd0/0x130
vfs_write+0xb2/0x1b0
SyS_pwrite64+0x69/0xa0
? vtime_user_exit+0x29/0x70
do_syscall_64+0x6e/0x160
entry_SYSCALL64_slow_path+0x25/0x25
RIP: new_curseg+0x36f/0x380 [f2fs] RSP: ffffac570393f7a8
So this patch introduces a parameter map.m_may_create to indicate that
f2fs_map_blocks() is called from write or read path, which can give the
right hint to let f2fs_map_blocks() trigger OPU allocation and call
f2fs_balanc_fs() correctly.
BTW, it disables physical address preallocation for direct IO in
f2fs_preallocate_blocks, which is redundant to OPU allocation of
f2fs_map_blocks.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds f2fs_dio_submit_bio() to hook submit_io/end_io functions
in direct IO path, in order to account DIO.
Later, we will add this count into is_idle() to let background GC/Discard
thread be aware of DIO.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Section is minimal garbage collection unit of f2fs, in zoned block
device, or ancient block mapping flash device, in order to improve
GC efficiency, we can align GC unit to lower device erase unit,
normally, it consists of multiple of segments.
Once background or foreground GC triggers, it brings a large number
of IOs, which will impact user IO, and also occupy cpu/memory resource
intensively.
So, to reduce impact of GC on large size section, this patch supports
subsectional GC, in one cycle of GC, it only migrate partial segment{s}
in victim section. Currently, by default, we use sbi->segs_per_sec as
migration granularity.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Introduce a wrapper __is_large_section() to clean up codes.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In F2FS_HAS_FEATURE(), we will use F2FS_SB(sb) to get sbi pointer to
access .raw_super field, to avoid unneeded pointer conversion, this
patch changes to F2FS_HAS_FEATURE() accept sbi parameter directly.
Just do cleanup, no logic change.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Pull XArray conversion from Matthew Wilcox:
"The XArray provides an improved interface to the radix tree data
structure, providing locking as part of the API, specifying GFP flags
at allocation time, eliminating preloading, less re-walking the tree,
more efficient iterations and not exposing RCU-protected pointers to
its users.
This patch set
1. Introduces the XArray implementation
2. Converts the pagecache to use it
3. Converts memremap to use it
The page cache is the most complex and important user of the radix
tree, so converting it was most important. Converting the memremap
code removes the only other user of the multiorder code, which allows
us to remove the radix tree code that supported it.
I have 40+ followup patches to convert many other users of the radix
tree over to the XArray, but I'd like to get this part in first. The
other conversions haven't been in linux-next and aren't suitable for
applying yet, but you can see them in the xarray-conv branch if you're
interested"
* 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits)
radix tree: Remove multiorder support
radix tree test: Convert multiorder tests to XArray
radix tree tests: Convert item_delete_rcu to XArray
radix tree tests: Convert item_kill_tree to XArray
radix tree tests: Move item_insert_order
radix tree test suite: Remove multiorder benchmarking
radix tree test suite: Remove __item_insert
memremap: Convert to XArray
xarray: Add range store functionality
xarray: Move multiorder_check to in-kernel tests
xarray: Move multiorder_shrink to kernel tests
xarray: Move multiorder account test in-kernel
radix tree test suite: Convert iteration test to XArray
radix tree test suite: Convert tag_tagged_items to XArray
radix tree: Remove radix_tree_clear_tags
radix tree: Remove radix_tree_maybe_preload_order
radix tree: Remove split/join code
radix tree: Remove radix_tree_update_node_t
page cache: Finish XArray conversion
dax: Convert page fault handlers to XArray
...
This patch does below changes to keep consistence of project quota data
in sudden power-cut case:
- update inode.i_projid and project quota atomically under lock_op() in
f2fs_ioc_setproject()
- recover inode.i_projid and project quota in recover_inode()
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For journalled quota mode, let checkpoint to flush dquot dirty data
and quota file data to guarntee persistence of all quota sysfile in
last checkpoint, by this way, we can avoid corrupting quota sysfile
when encountering SPO.
The implementation is as below:
1. add a global state SBI_QUOTA_NEED_FLUSH to indicate that there is
cached dquot metadata changes in quota subsystem, and later checkpoint
should:
a) flush dquot metadata into quota file.
b) flush quota file to storage to keep file usage be consistent.
2. add a global state SBI_QUOTA_NEED_REPAIR to indicate that quota
operation failed due to -EIO or -ENOSPC, so later,
a) checkpoint will skip syncing dquot metadata.
b) CP_QUOTA_NEED_FSCK_FLAG will be set in last cp pack to give a
hint for fsck repairing.
3. add a global state SBI_QUOTA_SKIP_FLUSH, in checkpoint, if quota
data updating is very heavy, it may cause hungtask in block_operation().
To avoid this, if our retry time exceed threshold, let's just skip
flushing and retry in next checkpoint().
Signed-off-by: Weichao Guo <guoweichao@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: avoid warnings and set fsck flag]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Direct IO can be used in case of hardware encryption. The following
scenario results into data corruption issue in this path -
Thread A - Thread B-
-> write file#1 in direct IO
-> GC gets kicked in
-> GC submitted bio on meta mapping
for file#1, but pending completion
-> write file#1 again with new data
in direct IO
-> GC bio gets completed now
-> GC writes old data to the new
location and thus file#1 is
corrupted.
Fix this by submitting and waiting for pending io on meta mapping
for direct IO case in f2fs_map_blocks().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch changes codes as below:
- use f2fs_set_inode_flags() to update i_flags atomically to avoid
potential race.
- synchronize F2FS_I(inode)->i_flags to inode->i_flags in
f2fs_new_inode().
- use f2fs_set_inode_flags() to simply codes in f2fs_quota_{on,off}.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds issued read IO counts which is under block layer.
Chao modified a bit, since:
Below race can cause reversed reference on F2FS_RD_DATA, there is
the same issue in f2fs_submit_page_bio(), fix them by relocate
__submit_bio() and inc_page_count.
Thread A Thread B
- f2fs_write_begin
- f2fs_submit_page_read
- __submit_bio
- f2fs_read_end_io
- __read_end_io
- dec_page_count(, F2FS_RD_DATA)
- inc_page_count(, F2FS_RD_DATA)
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This doesn't work on stacked devices, and it doesn't work on
blk-mq devices. The request_list is only used on legacy, which
we don't have much of anymore, and soon won't have any of.
Kill the check.
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: linux-f2fs-devel@lists.sourceforge.net
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Commit a2a12b679f ("f2fs: export SSR allocation threshold") introduced
two threshold .min_ssr_sections and .trigger_ssr_threshold, but only
.min_ssr_sections is used, so just remove redundant one for cleanup.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
As rbtree supports caching leftmost node natively, update f2fs codes
to use rb_*_cached helpers to speed up leftmost node visiting.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When migrating encrypted block from background GC thread, we only add
them into f2fs inner bio cache, but forget to submit the cached bio, it
may cause potential deadlock when we are waiting page writebacked, fix
it.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Note that, it requires "f2fs: return correct errno in f2fs_gc".
This adds a lightweight non-persistent snapshotting scheme to f2fs.
To use, mount with the option checkpoint=disable, and to return to
normal operation, remount with checkpoint=enable. If the filesystem
is shut down before remounting with checkpoint=enable, it will revert
back to its apparent state when it was first mounted with
checkpoint=disable. This is useful for situations where you wish to be
able to roll back the state of the disk in case of some critical
failure.
Signed-off-by: Daniel Rosenberg <drosen@google.com>
[Jaegeuk Kim: use SB_RDONLY instead of MS_RDONLY]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Normally, DIO uses in-pllace-update, but in LFS mode, f2fs doesn't
allow triggering any in-place-update writes, so we fallback direct
write to buffered write, result in bad performance of large size
write.
This patch adds to support triggering out-place-update for direct IO
to enhance its performance.
Note that it needs to exclude direct read IO during direct write,
since new data writing to new block address will no be valid until
write finished.
storage: zram
time xfs_io -f -d /mnt/f2fs/file -c "pwrite 0 1073741824" -c "fsync"
Before:
real 0m13.061s
user 0m0.327s
sys 0m12.486s
After:
real 0m6.448s
user 0m0.228s
sys 0m6.212s
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>