Introduce a bitfield to allow the drivers to announce the available
features for an RTC.
The main use case would be to better handle alarms, that could be present
or not or have a minute resolution or may need a correct week day to be set.
Use the newly introduced RTC_FEATURE_ALARM bit to then test whether alarms
are available instead of relying on the presence of ops->set_alarm.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210110231752.1418816-2-alexandre.belloni@bootlin.com
Subsystem:
- Remove nvram ABI. There was no complaints about the deprecation for the last
3 years.
- Improve RTC device allocation and registration
- Now available for ARCH=um
Drivers:
- at91rm9200: correction and sam9x60 support
- ds1307: improve ACPI support
- mxc: now DT only
- pcf2127: watchdog support now needs the reset-source property
- pcf8523: set range
- rx6110: i2c support
-----BEGIN PGP SIGNATURE-----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=n8V2
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Remove nvram ABI. There was no complaints about the deprecation for
the last 3 years.
- Improve RTC device allocation and registration
- Now available for ARCH=um
Drivers:
- at91rm9200: correction and sam9x60 support
- ds1307: improve ACPI support
- mxc: now DT only
- pcf2127: watchdog support now needs the reset-source property
- pcf8523: set range
- rx6110: i2c support"
* tag 'rtc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (43 commits)
rtc: pcf2127: only use watchdog when explicitly available
dt-bindings: rtc: add reset-source property
rtc: fix RTC removal
rtc: s3c: Remove dead code related to periodic tick handling
rtc: s3c: Disable all enable (RTC, tick) bits in the probe
rtc: ep93xx: Fix NULL pointer dereference in ep93xx_rtc_read_time
rtc: test: remove debug message
rtc: mxc{,_v2}: enable COMPILE_TEST
rtc: enable RTC framework on ARCH=um
rtc: pcf8523: use BIT
rtc: pcf8523: set range
rtc: pcf8523: switch to devm_rtc_allocate_device
rtc: destroy mutex when releasing the device
rtc: shrink devm_rtc_allocate_device()
rtc: rework rtc_register_device() resource management
rtc: nvmem: emit an error message when nvmem registration fails
rtc: add devm_ prefix to rtc_nvmem_register()
rtc: nvmem: remove nvram ABI
Documentation: list RTC devres helpers in devres.rst
rtc: omap: use devm_pinctrl_register()
...
Since the rtc_register_device, removing an RTC device will end with a
refcount_t: underflow; use-after-free warning since put_device is called
twice in the device tear down path.
Fixes: fdcfd85433 ("rtc: rework rtc_register_device() resource management")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201205231449.610980-1-alexandre.belloni@bootlin.com
The current RTC set_offset_nsec value is not really intuitive to
understand.
tsched twrite(t2.tv_sec - 1) t2 (seconds increment)
The offset is calculated from twrite based on the assumption that t2 -
twrite == 1s. That means for the MC146818 RTC the offset needs to be
negative so that the write happens 500ms before t2.
It's easier to understand when the whole calculation is based on t2. That
avoids negative offsets and the meaning is obvious:
t2 - twrite: The time defined by the chip when seconds increment
after the write.
twrite - tsched: The time for the transport to the point where the chip
is updated.
==> set_offset_nsec = t2 - tsched
ttransport = twrite - tsched
tRTCinc = t2 - twrite
==> set_offset_nsec = ttransport + tRTCinc
tRTCinc is a chip property and can be obtained from the data sheet.
ttransport depends on how the RTC is connected. It is close to 0 for
directly accessible RTCs. For RTCs behind a slow bus, e.g. i2c, it's the
time required to send the update over the bus. This can be estimated or
even calibrated, but that's a different problem.
Adjust the implementation and update comments accordingly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201206220542.263204937@linutronix.de
The offset which is used to steer the start of an RTC synchronization
update via rtc_set_ntp_time() is huge. The math behind this is:
tsched twrite(t2.tv_sec - 1) t2 (seconds increment)
twrite - tsched is the transport time for the write to hit the device.
t2 - twrite depends on the chip and is for most chips one second.
The rtc_set_ntp_time() calculation of tsched is:
tsched = t2 - 1sec - (t2 - twrite)
The default for the sync offset is 500ms which means that twrite - tsched
is 500ms assumed that t2 - twrite is one second.
This is 0.5 seconds off for RTCs which are directly accessible by IO writes
and probably for the majority of i2C/SPI based RTC off by an order of
magnitude. Set it to 5ms which should bring it closer to reality.
The default can be adjusted by drivers (rtc_cmos does so) and could be
adjusted further by a calibration method which is an orthogonal problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201206220541.960333166@linutronix.de
Not destroying mutexes doesn't lead to resource leak but it's the correct
thing to do for mutex debugging accounting.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201110094205.8972-1-brgl@bgdev.pl
We don't need to use devres_alloc() & devres_add() manually if all we
want to manage is a single pointer. We can shrink the code by using
devm_add_action_or_reset() instead. The number of allocations stays
the same.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-9-brgl@bgdev.pl
rtc_register_device() is a managed interface but it doesn't use devres
by itself - instead it marks an rtc_device as "registered" and the devres
callback for devm_rtc_allocate_device() takes care of resource release.
This doesn't correspond with the design behind devres where managed
structures should not be aware of being managed. The correct solution
here is to register a separate devres callback for unregistering the
device.
While at it: rename rtc_register_device() to devm_rtc_register_device()
and add it to the list of managed interfaces in devres.rst. This way we
can avoid any potential confusion of driver developers who may expect
there to exist a corresponding unregister function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-8-brgl@bgdev.pl
The nvram sysfs attributes have been deprecated at least since v4.13, more
than 3 years ago and nobody ever complained about the deprecation warning.
Remove the sysfs attributes now.
[Bartosz: remove the declaration of rtc_nvmem_unregister()]
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201109163409.24301-5-brgl@bgdev.pl
The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200402110411.508534-1-colin.king@canonical.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Due to distribution constraints it may not be possible to statically
compile the required RTC driver into the kernel.
Expand RTC_HCTOSYS support to cover all RTC devices (statically compiled
or not) by checking at the end of RTC device registration whether the
time should be synced.
Signed-off-by: Steve Muckle <smuckle@google.com>
Link: https://lore.kernel.org/r/20191106194625.116692-1-smuckle@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a message when __rtc_register_device fails because rtc->ops is NULL.
This may only happen when developing a new driver so use dev_dbg to avoid
compiling it in by default.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20190818220041.17833-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use SPDX-License-Identifier instead of a verbose license text. Also fix the
block comment alignment.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement devm_rtc_device_register using devm_rtc_allocate_device and
__rtc_register_device so there is only one path left to register rtc
devices.
Also mark it as deprecated so new drivers will hopefully use
devm_rtc_allocate_device and rtc_register_device that are less race prone
and allow avoiding the 2038, 2070, 2100 and 2106 bugs properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
All the remaining users of rtc_timers are passing the rtc_device as private
data. Enforce that and rename private_data to rtc.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
devm_rtc_device_unregister is not used by any driver and should not be used
by any new driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ensure the non managed version of the un/registration functions is not used
anymore. No driver is using it anymore and they should not be necessary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
getnstimeofday64() is just a wrapper around the ktime accessor, so
we should use that directly.
I considered using ktime_get_boottime_ts64() (to avoid leap second
problems) or ktime_get_real_seconds() (to simplify the calculation,
but in the end concluded that the existing interface is probably
the most appropriate in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
From our investigation for all RTC drivers, 1 driver will be expired before
year 2017, 7 drivers will be expired before year 2038, 23 drivers will be
expired before year 2069, 72 drivers will be expired before 2100 and 104
drivers will be expired before 2106. Especially for these early expired
drivers, we need to expand the RTC range to make the RTC can still work
after the expired year.
So we can expand the RTC range by adding one offset to the time when reading
from hardware, and subtracting it when writing back. For example, if you have
an RTC that can do 100 years, and currently is configured to be based in
Jan 1 1970, so it can represents times from 1970 to 2069. Then if you change
the start year from 1970 to 2000, which means it can represents times from
2000 to 2099. By adding or subtracting the offset produced by moving the wrap
point, all times between 1970 and 1999 from RTC hardware could get interpreted
as times from 2070 to 2099, but the interpretation of dates between 2000 and
2069 would not change.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Because nvmem_config is only used and copied at nvmem registration, remove
it from struct rtc_device.
All the rtc drivers using nvmem are now calling rtc_nvmem_register
directly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch the parent of the nvmem device to the parent of the rtc device so it
can be registered before the RTC.
This is a small change in the ABI as the nvmem moves out of the
/sys/class/rtc/rtcX folder to be under the parent device folder (that is
where the previous nvram files where registered).
However, it is still available under its correct location,
/sys/bus/nvmem/devices which is the one that should be used by userspace
applications.
The other benefit is that the nvmem device can stay registered even if the
rtc registration fails. Or it is possible to not register the rtc if the
nvmem registration failed.
Finally, it makes a lot of sense for devices that actually have different
i2c or spi addresses for the RTC and the EEPROM. That is basically how it
would end up when using MFD or even completely separate devices.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
To be able to remove nvmem_config from struct rtc_device, pass it as a
parameter to rtc_nvmem_register.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ntp is currently hardwired to try and call the rtc set when wall clock
tv_nsec is 0.5 seconds. This historical behaviour works well with certain
PC RTCs, but is not universal to all rtc hardware.
Change how this works by introducing the driver specific concept of
set_offset_nsec, the delay between current wall clock time and the target
time to set (with a 0 tv_nsecs).
For x86-style CMOS set_offset_nsec should be -0.5 s which causes the last
second to be written 0.5 s after it has started.
For compat with the old rtc_set_ntp_time, the value is defaulted to
+ 0.5 s, which causes the next second to be written 0.5s before it starts,
as things were before this patch.
Testing shows many non-x86 RTCs would like set_offset_nsec ~= 0,
so ultimately each RTC driver should set the set_offset_nsec according
to its needs, and non x86 architectures should stop using
update_persistent_clock64 in order to access this feature.
Future patches will revise the drivers as needed.
Since CMOS and RTC now have very different handling they are split
into two dedicated code paths, sharing the support code, and ifdefs
are replaced with IS_ENABLED.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Many RTCs have an on board non volatile storage. It can be battery backed
RAM or an EEPROM. Use the nvmem subsystem to export it to both userspace
and in-kernel consumers.
This stays compatible with the previous (non documented) ABI that was using
/sys/class/rtc/rtcx/device/nvram to export that memory. But will warn about
the deprecation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Introduce rtc_register_device() to register an already allocated and
initialized struct rtc_device. It automatically sets up the owner and the
two steps allocation/registration will allow to remove race conditions in
the IRQ handling of some driver. It also allows to properly extend the core
without adding more arguments to rtc_device_register().
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Create rtc_allocate_device to allocate memory for a struct rtc_device and
initialize it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc->name is only used in messages were it is superfluous. Remove it
completely from the structure.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Mostly straightforward, but we had to remove the rtc_dev_add/del_device
functions as they split up the cdev_add and the device_add.
Doing this also revealed that there was likely another subtle bug:
seeing cdev_add was done after device_register, the cdev probably
was not ready before device_add when the uevent occurs. This would
race with userspace, if it tried to use the device directly after
the uevent. This is fixed just by using the new helper function.
Another weird thing is this driver would, in some error cases, call
cdev_add() without calling cdev_init. This patchset corrects this
by avoiding calling cdev_add if the devt is not set.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Makefile/Kconfig currently controlling compilation of this code is:
obj-$(CONFIG_RTC_CLASS) += rtc-core.o
rtc-core-y := class.o interface.o
drivers/rtc/Kconfig:menuconfig RTC_CLASS
drivers/rtc/Kconfig: bool "Real Time Clock"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the code there is no doubt it is builtin-only.
We don't replace module.h with init.h since the file does need
to know what a struct module is.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of creating wakealarm attribute manually, after the device has been
registered, let's rely on facilities provided by the attribute groups to
control which attributes are visible and which are not. This allows to
create all needed attributes at once, at the same time that we register RTC
class device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Technically the address of rtc->dev can never be NULL, so get_device()
can never fail. Also caller of rtc_device_unregister() supposed to be
the owner of the device and thus have a valid reference. Therefore
call to get_device() is not needed here.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 59cca865f2 ("drivers/rtc/class.c: fix device_register() error
handling") correctly noted that naked kfree() should not be used after
failed device_register() call, however, while it added the needed
put_device() it forgot to remove the original kfree() causing double-free.
Cc: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In some error cases RTC name is used before it is initialized:
rtc-rs5c372 0-0032: clock needs to be set
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc (null): read_time: fail to read
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
Fix by initializing the name early.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a system does not provide a persistent_clock(), the time
will be updated on resume by rtc_resume(). With the addition
of the non-stop clocksources for suspend timing, those systems
set the time on resume in timekeeping_resume(), but may not
provide a valid persistent_clock().
This results in the rtc_resume() logic thinking no one has set
the time and it then will over-write the suspend time again,
which is not necessary and only increases clock error.
So, fix this for rtc_resume().
This patch also improves the name of persistent_clock_exist to
make it more grammatical.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-19-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rtc_read_time() has already judged valid tm by rtc_valid_tm(),
so just remove it.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-17-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the rtc suspend/resume timing is done using
y2038 problematic timespecs. So update the code to utilize
timespec64 types.
Signed-off-by: John Stultz <john.stultz@linaro.org>
In rtc_suspend() and rtc_resume(), the error after rtc_read_time() is not
checked. If rtc device fail to read time, we cannot guarantee the
following process.
Add the verification code for returned rtc_read_time() error.
Signed-off-by: Hyogi Gim <hyogi.gim@lge.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Assign RTC device IDs based on device tree /aliases entries if present,
falling back to the existing numbering scheme if there is no /aliases
entry (which includes when the system isn't booted using DT), or there is
a numbering conflict.
This is useful in systems with multiple RTC devices, to ensure that the
best RTC device is selected as /dev/rtc0, which provides the overall
system time.
For example, Tegra has an on-SoC RTC that is not battery backed, typically
coupled with an off-SoC RTC that is battery backed. Only the latter is
useful for populating the system time, yet the former is useful e.g. for
wakeup timing, since the time is not lost when the system is sleeps.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert drivers/rtc/class to use dev_pm_ops for power management and
remove Legacy PM ops hooks. With this change, rtc class registers
suspend/resume callbacks via class->pm (dev_pm_ops) instead of Legacy
class->suspend/resume. When __device_suspend() runs call-backs, it will
find class->pm ops for the rtc class.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Other devm_* APIs use 'struct device *dev' as the first argument. Thus,
in order to sync with other devm_* functions, struct device is used as
the first argument for devm_rtc_device_register().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These functions allow the driver core to automatically clean up any
allocation made by rtc drivers. Thus it simplifies the error paths.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All the RTC suspend and resume functions are to compensate the
sleep time, but this is already done in timekeeping.c if persistent
clock exist.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Revert commit 2830a6d201.
We already perform the ida_simple_remove() in rtc_device_release(),
which is an appropriate place. Commit 2830a6d20 ("rtc: recycle id when
unloading a rtc driver") caused the kernel to emit
ida_remove called for id=0 which is not allocated.
warnings when rtc_device_release() tries to release an alread-released
ID.
Let's restore things to their previous state and then work out why
Vincent's kernel wasn't calling rtc_device_release() - presumably a bug
in a specific sub-driver.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Alexander Holler <holler@ahsoftware.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: <stable@vger.kernel.org> [3.7.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Belloni
Linus Torvalds
Thomas Gleixner
Bartosz Golaszewski
Colin Ian King
Steve Muckle
Arnd Bergmann
Baolin Wang
Jason Gunthorpe
Alexandre Belloni
Logan Gunthorpe
Paul Gortmaker
Dmitry Torokhov
Aaro Koskinen
Xunlei Pang
John Stultz
Hyogi Gim
Stephen Warren
Shuah Khan
Jingoo Han
Feng Tang
Andrew Morton