Core changes:
- New standard enumerator and corresponding device tree bindings
for output impedance pin configuration. (Implemented and used
in the Renesas rzg2l driver.)
- Cleanup of Kconfig and Makefile to be somewhat orderly and
alphabetic.
New drivers:
- Samsung Exynos 7885 pin controller.
- Ocelot LAN966x pin controller.
- Qualcomm SDX65 pin controller.
- Qualcomm SM8450 pin controller.
- Qualcomm PM8019, PM8226 and PM2250 pin controllers.
- NXP/Freescale i.MXRT1050 pin controller.
- Intel Thunder Bay pin controller.
Enhancements:
- Introduction of the string library helper function
"kasprintf_strarray()" and subsequent use in Rockchip, ST and
Armada pin control drivers, as well as the GPIO mockup driver.
- The Ocelot pin controller has been extensively rewritten to
use regmap and other modern kernel infrastructure.
- The Microchip SGPIO driver has been converted to use regmap.
- The SPEAr driver had been converted to use regmap.
- Substantial cleanups and janitorial on the Apple pin control
driver that was merged for v5.16.
- Janitorial to remove of_node assignments in the GPIO portions
that anyway get this handled in the GPIO core.
- Minor cleanups and improvements in several pin controllers.
-----BEGIN PGP SIGNATURE-----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=+nxh
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk updates from Linus Walleij:
"Core changes:
- New standard enumerator and corresponding device tree bindings for
output impedance pin configuration. (Implemented and used in the
Renesas rzg2l driver.)
- Cleanup of Kconfig and Makefile to be somewhat orderly and
alphabetic.
New drivers:
- Samsung Exynos 7885 pin controller.
- Ocelot LAN966x pin controller.
- Qualcomm SDX65 pin controller.
- Qualcomm SM8450 pin controller.
- Qualcomm PM8019, PM8226 and PM2250 pin controllers.
- NXP/Freescale i.MXRT1050 pin controller.
- Intel Thunder Bay pin controller.
Enhancements:
- Introduction of the string library helper function
"kasprintf_strarray()" and subsequent use in Rockchip, ST and
Armada pin control drivers, as well as the GPIO mockup driver.
- The Ocelot pin controller has been extensively rewritten to use
regmap and other modern kernel infrastructure.
- The Microchip SGPIO driver has been converted to use regmap.
- The SPEAr driver had been converted to use regmap.
- Substantial cleanups and janitorial on the Apple pin control driver
that was merged for v5.16.
- Janitorial to remove of_node assignments in the GPIO portions that
anyway get this handled in the GPIO core.
- Minor cleanups and improvements in several pin controllers"
* tag 'pinctrl-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (98 commits)
pinctrl: imx: fix assigning groups names
dt-bindings: pinctrl: mt8195: add wrapping node of pin configurations
pinctrl: bcm: ns: use generic groups & functions helpers
pinctrl: imx: fix allocation result check
pinctrl: samsung: Use platform_get_irq_optional() to get the interrupt
pinctrl: Propagate firmware node from a parent device
dt-bindings: pinctrl: qcom: Add SDX65 pinctrl bindings
pinctrl: add one more "const" for generic function groups
pinctrl: keembay: rework loops looking for groups names
pinctrl: keembay: comment process of building functions a bit
pinctrl: imx: prepare for making "group_names" in "function_desc" const
ARM: dts: gpio-ranges property is now required
pinctrl: aspeed: fix unmet dependencies on MFD_SYSCON for PINCTRL_ASPEED
pinctrl: Get rid of duplicate of_node assignment in the drivers
pinctrl-sunxi: don't call pinctrl_gpio_direction()
pinctrl-bcm2835: don't call pinctrl_gpio_direction()
pinctrl: bcm2835: Silence uninit warning
pinctrl: Sort Kconfig and Makefile entries alphabetically
pinctrl: Add Intel Thunder Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Thunderbay pinctrl driver
...
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype
board, with additional boards to be added later. This SoC promises
to be the first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding
a few other Arm based SoCs as well, but those did not pass the
review in time, so it's only this one.
-----BEGIN PGP SIGNATURE-----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=X5uk
-----END PGP SIGNATURE-----
Merge tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull RISC-V SoC updates from Arnd Bergmann:
"Add support for StarFive JH7100 RISC-V SoC
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype board,
with additional boards to be added later. This SoC promises to be the
first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding a
few other Arm based SoCs as well, but those did not pass the review in
time, so it's only this one"
* tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
reset: starfive-jh7100: Fix 32bit compilation
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
1. Add support for Exynos7885.
2. Drop usage of platform_get_resource().
-----BEGIN PGP SIGNATURE-----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=hka6
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-5.17' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v5.17
1. Add support for Exynos7885.
2. Drop usage of platform_get_resource().
This simplifies ns driver and gets rid of ~70 lines of code.
"const" had to be dropped from "struct ns_pinctrl_group" @pins to match
"struct group_desc" @pins and pinctrl_generic_add_group(). Otherwise it
would cause:
drivers/pinctrl/bcm/pinctrl-ns.c: In function 'ns_pinctrl_probe':
drivers/pinctrl/bcm/pinctrl-ns.c:277:13: warning: passing argument 3 of 'pinctrl_generic_add_group' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
277 | group->pins, group->num_pins, NULL);
| ~~~~~^~~~~~
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211222064344.14624-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix code to check correct variable value.
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Fixes: 02f1171349 ("pinctrl: imx: prepare for making "group_names" in "function_desc" const")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20211222212807.27122-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224145748.18754-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
When creating MFD platform devices the firmware node is left unset.
This, in particular, prevents GPIO library to use it for different
purposes. Propagate firmware node from the parent device and let
GPIO library do the right thing.
While at it, slightly modify the headers to reflect the usage of APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20211216151227.58687-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Generic code doesn't modify those strings and .get_function_groups
callback has that extra "const" as well. This allows more flexibility in
GENERIC_PINMUX_FUNCTIONS users.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-4-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the outer loop iterate over functions as that's the real subject.
This simplifies code (and reduces amount of lines of code) as allocating
memory for names doesn't require extra checks anymore.
While at it use local "group_names" variable. The plan for
"struct function_desc" is to make its "group_names" /double/ const. That
will allow drivers to use it with static const data.
This keembay "group_names" change is required to avoid:
drivers/pinctrl/pinctrl-keembay.c: In function 'keembay_add_functions':
drivers/pinctrl/pinctrl-keembay.c:1594:8: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1594 | grp = func->group_names;
| ^
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-3-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This should make code a bit easier to follow. While at it use some "for"
loops to simplify array iteration loops.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-2-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The plan for "struct function_desc" is to make its "group_names"
/double/ const. That will allow drivers to use it with static const
data.
This imx change is required to avoid:
drivers/pinctrl/freescale/pinctrl-imx.c: In function 'imx_pinctrl_parse_functions':
drivers/pinctrl/freescale/pinctrl-imx.c:672:24: error: assignment of read-only location '*(func->group_names + (sizetype)(i * 4))'
672 | func->group_names[i] = child->name;
| ^
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Align comments in the R-Car V3U pin control driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYbxj9gAKCRCKwlD9ZEnx
cMhKAQD+V66ADB9lwaSKLNwxK5TA8v6hpJTOP7FXFcbhpzafyQD/d9QETuTFehxZ
PyNfggjhzv6yi0qdIOvbv+t4lcf/4wo=
=WvSa
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.17 (take two)
- Align comments in the R-Car V3U pin control driver.
This adds support for the StarFive JH7100 RISC-V SoC. The SoC has many
devices that need non-coherent DMA operations to work which isn't
upstream yet[1], so this just adds basic support to boot up, get a
serial console, blink an LED and reboot itself. Unlike the Allwinner D1
this chip doesn't use any extra pagetable bits, but instead the DDR RAM
appears twice in the memory map, with and without the cache.
The JH7100 is a test chip for the upcoming JH7110 and about 300 BeagleV
Starlight Beta boards were sent out with them as part of a now cancelled
BeagleBoard.org project. However StarFive has produced more of the
JH7100s and will be selling VisionFive boards with them soon[2].
[1]: https://lore.kernel.org/linux-riscv/20210723214031.3251801-2-atish.patra@wdc.com/
[2]: https://www.cnx-software.com/2021/12/09/starfive-visionfive-single-board-computer-for-sale-accelerating-risc-v-ecosystem-development/
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTtU6YTJ5V9vBl9M/+39ymfrXW1/gUCYbtpnAAKCRC39ymfrXW1
/skTAQD6hDKWL5jLLCa4fN6yaovSC9RC4EPYmXpj2krzFMqcvwEA/OFHLp+buXhV
n1BGpTieVfRMV5HJZhFK3aAED9+SQQY=
=r5lD
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=TBjW
-----END PGP SIGNATURE-----
Merge tag 'jh7100-for-5.17' of https://github.com/esmil/linux into arm/newsoc
Basic StarFive JH7100 RISC-V SoC support
This adds support for the StarFive JH7100 RISC-V SoC. The SoC has many
devices that need non-coherent DMA operations to work which isn't
upstream yet[1], so this just adds basic support to boot up, get a
serial console, blink an LED and reboot itself. Unlike the Allwinner D1
this chip doesn't use any extra pagetable bits, but instead the DDR RAM
appears twice in the memory map, with and without the cache.
The JH7100 is a test chip for the upcoming JH7110 and about 300 BeagleV
Starlight Beta boards were sent out with them as part of a now cancelled
BeagleBoard.org project. However StarFive has produced more of the
JH7100s and will be selling VisionFive boards with them soon[2].
[1]: https://lore.kernel.org/linux-riscv/20210723214031.3251801-2-atish.patra@wdc.com/
[2]: https://www.cnx-software.com/2021/12/09/starfive-visionfive-single-board-computer-for-sale-accelerating-risc-v-ecosystem-development/
* tag 'jh7100-for-5.17' of https://github.com/esmil/linux:
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
Link: https://lore.kernel.org/r/20211216164205.286138-1-kernel@esmil.dk
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a combined pinctrl and GPIO driver for the JH7100 RISC-V SoC by
StarFive Ltd. This is a test chip for their upcoming JH7110 SoC, which
is said to feature only minor changes to these pinctrl/GPIO parts.
For each "GPIO" there are two registers for configuring the output and
output enable signals which may come from other peripherals. Among these
are two special signals that are constant 0 and constant 1 respectively.
Controlling the GPIOs from software is done by choosing one of these
signals. In other words the same registers are used for both pin muxing
and controlling the GPIOs, which makes it easier to combine the pinctrl
and GPIO driver in one.
I wrote the pinconf and pinmux parts, but the GPIO part of the code is
based on the GPIO driver in the vendor tree written by Huan Feng with
cleanups and fixes by Drew and me.
Datasheet: https://github.com/starfive-tech/JH7100_Docs/blob/main/JH7100%20Data%20Sheet%20V01.01.04-EN%20(4-21-2021).pdf
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Co-developed-by: Huan Feng <huan.feng@starfivetech.com>
Signed-off-by: Huan Feng <huan.feng@starfivetech.com>
Co-developed-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
When PINCTRL_ASPEED_G* is selected,
and MFD_SYSCON is not selected,
Kbuild gives the following warnings:
WARNING: unmet direct dependencies detected for PINCTRL_ASPEED
Depends on [n]: PINCTRL [=y] && (ARCH_ASPEED [=n] || COMPILE_TEST [=y]) && OF [=y] && MFD_SYSCON [=n]
Selected by [y]:
- PINCTRL_ASPEED_G4 [=y] && PINCTRL [=y] && (MACH_ASPEED_G4 [=n] || COMPILE_TEST [=y]) && OF [=y]
WARNING: unmet direct dependencies detected for PINCTRL_ASPEED
Depends on [n]: PINCTRL [=y] && (ARCH_ASPEED [=n] || COMPILE_TEST [=y]) && OF [=y] && MFD_S>
Selected by [y]:
- PINCTRL_ASPEED_G5 [=y] && PINCTRL [=y] && (MACH_ASPEED_G5 [=n] || COMPILE_TEST [=y]) && O>
WARNING: unmet direct dependencies detected for PINCTRL_ASPEED
Depends on [n]: PINCTRL [=y] && (ARCH_ASPEED [=n] || COMPILE_TEST [=y]) && OF [=y] && MFD_S>
Selected by [y]:
- PINCTRL_ASPEED_G6 [=y] && PINCTRL [=y] && (MACH_ASPEED_G6 [=n] || COMPILE_TEST [=y]) && O>
This is because MACH_ASPEED_G* depend on (ARCH_ASPEED || COMPILE_TEST).
ARCH_ASPEED enables the MFD_SYSCON dependency, but COMPILE_TEST doesn't.
These unmet dependency bugs were detected by Kismet,
a static analysis tool for Kconfig. Please advise
if this is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20211215214022.146391-1-julianbraha@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Intel Baytrail and Cherryview IRQ related fixes
The following is an automated git shortlog grouped by driver:
baytrail:
- Set IRQCHIP_SET_TYPE_MASKED flag on the irqchip
cherryview:
- Use temporary variable for struct device
- Do not allow the same interrupt line to be used by 2 pins
- Don't use selection 0 to mark an interrupt line as unused
-----BEGIN PGP SIGNATURE-----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=8Crg
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.17-3' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.17-3
* Intel Baytrail and Cherryview IRQ related fixes
The following is an automated git shortlog grouped by driver:
baytrail:
- Set IRQCHIP_SET_TYPE_MASKED flag on the irqchip
cherryview:
- Use temporary variable for struct device
- Do not allow the same interrupt line to be used by 2 pins
- Don't use selection 0 to mark an interrupt line as unused
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove these assignment all at once.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211214125855.33207-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consider the GPIO controller offset (from "gpio-ranges") to compute the
maximum GPIO line number.
This fixes an issue where gpio-ranges uses a non-null offset.
e.g.: gpio-ranges = <&pinctrl 6 86 10>
In that case the last valid GPIO line is not 9 but 15 (6 + 10 - 1)
Cc: stable@vger.kernel.org
Fixes: 67e2996f72 ("pinctrl: stm32: fix the reported number of GPIO lines per bank")
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Link: https://lore.kernel.org/r/20211215095808.621716-1-fabien.dessenne@foss.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set the direction directly without calling pinctrl_gpio_direction().
This avoids the mutex_lock() calls in that function, which would
invalid the can_sleep = false.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/20211206131648.1521868-4-hverkuil-cisco@xs4all.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set the direction directly without calling pinctrl_gpio_direction().
This avoids the mutex_lock() calls in that function, which would
invalid the can_sleep = false.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206131648.1521868-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
This also solves a similar problem with the gpio-ranges property, which
is required in order for released pins to be returned to inputs.
Fixes: 73345a18d4 ("pinctrl: bcm2835: Pass irqchip when adding gpiochip")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206092237.4105895-2-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The uninitialized variable would be caught by the BUG_ON()
logic below, but the kernel test robot cannot see that.
Silence the warning by initializing the variable.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211209134513.306212-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sort Kconfig and Makefile entries alphabetically for better maintenance
in the future.
While at it fix some style issues, such as:
- "Say Y"/"Say yes"/"Say Yes" --> "Say Y"
- "pullup/pulldown" --> "pull-up and pull-down"
- wrong indentation
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211209113456.33977-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
About Intel Thunder Bay:
-----------------------
Intel Thunder Bay is a computer vision AI accelerator SoC based on ARM CPU.
Pinctrl IP:
----------
The SoC has a customised pinmux controller IP which controls pin
multiplexing and configuration.
Thunder Bay pinctrl IP is not based on and have nothing in common with the
existing pinctrl drivers. The registers used are incompatible with the
existing drivers, so it requires a new driver.
Add pinctrl driver to enable pin control support in the Intel Thunder Bay
SoC.
Co-developed-by: Kiran Kumar S <kiran.kumar1.s@intel.com>
Signed-off-by: Kiran Kumar S <kiran.kumar1.s@intel.com>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Link: https://lore.kernel.org/r/20211201072626.19599-3-lakshmi.sowjanya.d@intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM8450 SoC
This patch is based on initial code downstream by
Elliot Berman <eberman@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201072434.3968768-3-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add generic support for output impedance,
- Add drive strength and output impedance support for the RZ/G2L SoC,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYan5bwAKCRCKwlD9ZEnx
cKxyAQCCsEC0VJNaD5TNsGt+ivfEyMpu5ZeKL3xb2qj0PMPKUgD/R09wo6KwZciv
OCUQy0jHYP880VG3AHkzdFVtG7SnjAc=
=n0dm
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.17-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.17
- Add generic support for output impedance,
- Add drive strength and output impedance support for the RZ/G2L SoC,
- Miscellaneous fixes and improvements.
Resources need to be shared between pinmux and plgpio.
Introduce regmap phandle in order to retrieve the regmap
from the phandle if the property is present.
This allows to retrieve an external regmap (ie the one
used by pinmux if the phandle references the pinmux node)
from plgpio.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20211202095255.165797-4-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Resources need to be shared between pinmux and plgpio.
Use regmap (syscon) to access resources to allow an
easy way to share resources.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20211202095255.165797-3-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Resources need to be shared between pinmux and plgpio.
Use regmap (syscon) to access resources to allow an
easy way to share resources.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20211202095255.165797-2-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Zero-length and one-element arrays are deprecated, see
Documentation/process/deprecated.rst
Flexible-array members should be used instead.
Generated by: scripts/coccinelle/misc/flexible_array.cocci
CC: Joey Gouly <joey.gouly@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2111271859250.2864@hadrien
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All the other mtk_hw_get_value() calls have a check for "if (err)" so
we can add one here as well. This silences a Smatch warning:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:819 mtk_pinconf_bias_get_rsel()
error: uninitialized symbol 'pd'.
Fixes: fb34a9ae38 ("pinctrl: mediatek: support rsel feature")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211127140836.GB24002@kili
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "try_all_type" variable is not set if (hw->soc->pull_type) is false
leading to the following Smatch warning:
drivers/pinctrl/mediatek/pinctrl-paris.c:599 mtk_pctrl_show_one_pin()
error: uninitialized symbol 'try_all_type'.
Fixes: fb34a9ae38 ("pinctrl: mediatek: support rsel feature")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211127140750.GA24002@kili
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO nodes are not themselves busses, so passing rockchip_bank_match
here is wrong. Passing NULL instead uses the standard bus match table
which is more appropriate.
devm_of_platform_populate() shows that this is the normal way to call
of_platform_populate() from a device driver, so in order to match that
more closely also add the pinctrl device as the parent for the newly
created GPIO controllers.
Specifically, using the wrong match here can break dynamic GPIO hogs as
marking the GPIO bank as a bus means that of_platform_notify() will set
OF_POPULATED on new child nodes and if this happens before
of_gpio_notify() is called then the new hog will be skipped as
OF_POPULATED is already set.
Fixes: 9ce9a02039 ("pinctrl/rockchip: drop the gpio related codes")
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20211126151352.1509583-1-john@metanate.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If of_property_count_u32_elems returned 0, return -EINVAL to indicate
a failure. Previously this would return 0.
Fixes: a0f160ffcb ("pinctrl: add pinctrl/GPIO driver for Apple SoCs")
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-12-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio core code sets of_node, so no need to do it here.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-10-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Having this missing, but everything else valid shouldn't result
in a failure.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-9-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Try to make this more readable by not using a long line with
a ternary operator.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-7-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Explicitly return 0 if the regmap_read fails.
Also change a uint32_t to a u32.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-6-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is needed for the BIT(n) macro.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-5-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the preferred comment style.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-4-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a missing comma at the end of the regmap initialisation.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-3-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reflow some of the code now that the extra '_gpio' was removed.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211121165642.27883-2-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmGavnseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGcl4H/jyFVlHDSa+utMA5
7PEQX0AarkBtSvKUgK/SivZxX06nYp2UU5L4Jn70O/mccXWo0ru82eDVO3nSImDR
Mi668IqzbYfGqVL6CMztDku+XbyT3Yr/i9QILFbLWV5DhCM422GXXN8PFBibDHdI
6Oyt1WoUh404yjVIHOCNwprfLObxREV6ARhFsIsmCRa8Hf+RkKOY5Twua6j5emm5
aamiq6SYLtf2H5+DwkR5TnPkie6I2o8oLtA7JYiJpKh5KK75qjlpzFd3S3OWsi1H
0g752g12r7tLh4ac3Xfgwf36pQ2CdiZ7NUOkJhZWT4aHPqPh+MVheQfpR41f5Sgc
pvFslTo=
=QdMf
-----END PGP SIGNATURE-----
Merge tag 'v5.16-rc2' into devel
Linux 5.16-rc2 is needed because nonurgent fixes headed
for next are strongly textually dependent on a fix that
was applied for rc2.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is impossible to use the same interrupt line for 2 pins, this will
result in the interrupts only being delivered to the IRQ handler for
the pin for which chv_gpio_irq_type() was called last.
The pinctrl-cherryview.c code relies on the BIOS to correctly setup the
interrupt line, but there is a BIOS bug on at least the Medion Akoya E1239T
and the GPD win models where both INT33FF:02 pin 8, used by the powerbutton
and INT33FF:02 pin 21 used as IRQ input for the accelerometer are mapped to
interrupt line 0.
This causes 2 problems:
1. The accelerometer IRQ does not work, since the power button is probed
later taking over the intr_lines[0] slot.
2. Since the accelerometer IRQ is not marked as wakeup, interrupt line 0
gets masked on suspend, causing the power button to not work to wake
the system from suspend.
Likewise on the Lenovo Yogabook, which has a touchscreen as keyboard
and the keyboard half of the tablet also has a Wacom digitizer, the BIOS
by default assigns the same interrupt line to the GPIOs used
for their interrupts.
Fix these problems by adding a check for this and assigning a new
interrupt line to the 2nd pin for which chv_gpio_irq_type() gets called.
With this fix in place the following 2 messages show up in dmesg on
the Medion Akoya E1239T and the GPD win:
cherryview-pinctrl INT33FF:02: interrupt line 0 is used by both pin 21 and pin 8
cherryview-pinctrl INT33FF:02: changing the interrupt line for pin 8 to 15
And the following gets logged on the Lenovo Yogabook:
cherryview-pinctrl INT33FF:01: interrupt-line 0 is used by both pin 49 and pin 56
cherryview-pinctrl INT33FF:01: changing the interrupt line for pin 56 to 7
Note commit 9747070c11 ("Input: axp20x-pek - always register interrupt
handlers") was added as a work around for the power button not being able
to wakeup the system. This relies on using the PMIC's connection to the
power button but that only works on systems with the AXP288 PMIC.
Once this fix has been merged that workaround can be removed.
Cc: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Linus Torvalds
Rafał Miłecki
Linus Walleij
Lad Prabhakar
Andy Shevchenko
Arnd Bergmann
Emil Renner Berthing
Julian Braha
Fabien Dessenne
Hans Verkuil
Phil Elwell
Lakshmi Sowjanya D
Vinod Koul
Geert Uytterhoeven
Herve Codina
kernel test robot
Dan Carpenter
Giulio Benetti
John Keeping
Joey Gouly
Hans de Goede