I noticed that during initialization sata_mv.c assumes that the main
interrupt mask has its default value of 0. The function
mv_platform_probe(..) initializes a shadow irq mask with 0 assuming
that's the value of the controller's register. Now
mv_set_main_irq_mask(..) only writes the controller's register if the
new value differs from the "shadowed" value. This is fatal when trying
to disable all interrupts in mv_init_host(..), i.e. the following
function call does not write anything to the main irq mask register:
mv_set_main_irq_mask(host, ~0, 0);
The effect I see on my machine (QNAP TS-109 II) with booting via kexec
(with Linux as a 2nd-stage boot loader) is that if the sata_mv module
was still loaded when performing kexec, then the new kernel's sata_mv
module starts up with interrupts enabled. This results in an unhandled
IRQ and breaks the boot process.
The unhandled interrupt itself might also be fixed by Lennert's patch
proposed at http://markmail.org/message/kwvzxstnlsa3s26w which I did not
try yet.
However I still propose to additionally initialize the shadow variable
with the current contents of the main irq mask register to get both in
sync and allow proper disabling the main irq mask. This fixes the
unhandled irq on my machine.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unneeded nsect restriction from GenII NCQ path,
and improve comments to explain why this is not a problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove silly read-modify-write sequences when clearing interrupts
in hc_irq_cause. This gets rid of unneeded MMIO reads, resulting in
a slight performance boost when switching between EDMA and non-EDMA
modes (eg. for cache flushes).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081),
where accesses to the upper 4 ports would cause lost-interrupts / timeouts
for the lower 4-ports. With this patch, the 6081 boards should finally be
reliable enough for mainstream use with Linux.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP5x family of controllers seem to share much more with nf2's as far
as reset protocol is concerned. It requires heardreset to get the PHY
going and classfication code report after hardreset is unreliable.
Create a new board type MCP5x and use noclassify hardreset. SWNCQ is
modified to inherit from this new type.
This fixes hotplug regression reported in kernel bz#12351.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
nv_nf2_hardreset() will be used by other flavors too. Rename it to
nv_noclassify_hardreset().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0. This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.
This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Impact: fix boot hang on pre-model-15 Intel CPUs
rdmsrl_safe() does not work in very early bootup code yet, because we
dont have the pagefault handler installed yet so exception section
does not get parsed. rdmsr_safe() will just crash and hang the bootup.
So limit the MSR_IA32_MISC_ENABLE MSR read to those CPU types that
support it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The EH message for NODEV_HINT path was describing the opposite
condition. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In the absence of PAT, PAGE_KERNEL_WC ends up mapping to a memory type that
gets UC behavior even in the presence of a WC MTRR covering the area in
question. By swapping to PAGE_KERNEL_UC_MINUS, we can get the actual
behavior the caller wanted (WC if you can manage it, UC otherwise).
This recovers the 40% performance improvement of using WC in the DRM
to upload vertex data.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Currently encap_oa is left uninitialized, so it contains garbage data which
is visible to userland via Netlink. Initialize it by zeroing it out.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1Q expanded the maximum ethernet frame size by 4 bytes for the
VLAN tag. We're not taking this into account in virtio_net, which
means the buffers we provide to the backend in the virtqueue RX ring
aren't big enough to hold a full MTU VLAN packet. For QEMU/KVM,
this results in the backend exiting with a packet truncation error.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/s390/net/lcs.c: In function 'lcs_new_device':
drivers/s390/net/lcs.c:2179: error: implicit declaration of function 'lcs_set_multicast_list'
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQF_DISABLED is not guaranteed for shared IRQs. I think power_changed_isr
doesn't need it anyway, as it only fires a timer.
This patch enables IRQF_SAMPLE_RANDOM instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tomi Valkeinen reports:
Running with latest linux-omap kernel on OMAP3 SDP board, I have
problem with iounmap(). It looks like iounmap() does not properly
free large areas. Below is a test which fails for me in 6-7 loops.
for (i = 0; i < 200; ++i) {
vaddr = ioremap(paddr, size);
if (!vaddr) {
printk("couldn't ioremap\n");
break;
}
iounmap(vaddr);
}
The changes to vmalloc.c weren't reflected in the ARM ioremap
implementation. Turns out the fix is rather simple.
Tested-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tested-by: Matt Gerassimoff <mgeras@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
the RDC and ELAN platforms use slighly different PIT clocks, resulting in
a timex.h hack that changes PIT_TICK_RATE during build time. But if a
tester enables any of these platform support .config options, the PIT
will be miscalibrated on standard PC platforms.
So use one frequency - in a subsequent patch we'll add a quirk to allow
x86 platforms to define different PIT frequencies.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is currently a DMA mapping leak that can occur in the ibmvfc
driver if we fail to allocate a scatterlist. Fix this by unmapping
the scatterlist in the failure path. Additionally, only log an error
for a scatterlist allocation failure if the log level is greater
than the default, since this can occur when running Active Memory
Sharing and this is not considered an error.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit f78badb1ae ([SCSI] fc
transport: pre-emptively terminate i/o upon dev_loss_tmo timeout)
changed the callback semantics of dev_loss_tmo and
terminate_rport_io such that repeated calls could be made. This
could result in the the driver using stale (NULLed-out, in
dev_loss_tmo) data from the rport. Correct this by addint a
simple check to ensure a valid fcport is attached.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeremy Higdon noted
(http://marc.info/?l=linux-scsi&m=123262143131788&w=2) that the
rework done in commit e315cd28b9
was not setting the proper consistent and streaming DMA masks
prior to memory allocations. Correct this and remove the
unnecessary prototype.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When clearing the flash device's SR, the comment is incorrect...
clearing the SR is 2 steps:
1. the SR protect bit is 1, so the first write zero clears only
that bit,
2. the SR protect bit is now 0, so the next write zero clears the
remaining bits.
The sector erase debug print more correctly identifies that the erase failed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 73208dfd7a (qla2xxx: add
support for multi-queue adapter) inadvertently backed-out the fix
in 5bff55db3d (qla2xxx: Return a
FAILED status when abort mailbox-command fails.).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The flash data was incorrectly being converted (cpu_to_le32())
when using the bulk-flash-write mailbox command (ISP25xx and
above).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP81XX parts (including ISP24xx and ISP25xx) could contain a
firmware image within a segment of flash, driver would fallback
to loading this firmware if the request-firmware interface failed
(userspace .bin file). Moving forward, all ISP81XX parts will
ship with a suggested-to-be-used firmware image within flash
which all driver should first attempt to load. If the flash
firmware load fails, the driver will then fallback to loading
firmware via the request-firmware interface (ql8100_fw.bin).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would incorrectly bypass serialization if the DPC
thread were performing a big-hammer operation (ISP abort). This
short circuit, though rare, would subsequently stomp on a
secondary thread's mailbox command execution. Found during
ISP81XX testing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code should work as well given qla24xx_reset_adapter()
is only called in extreme cases where the HBA is taken offline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Also removes unneeded 'findex' local variable within routine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
qla4xxx does not check the I_T nexus values correctly
so it ends up creating one session to the target. If
a portal should disappear or they should be reported
in different order the driver will think it is already
logged in when it could now be speaking to a different
target portal or accessing it through a different
initiator port (iscsi initiator port is not tied to
hardware and is just the initiator name plus isid
so you could end up with multiple ports through one
host).
This patch has the driver check the iscsi scsi port
values when matching sessions (we do not check
the initiator name because that is static). It results
in a portal from each target portal group getting
logged into instead of just one per target. In the future
the firmware should hopefully send us notification of other
sessions that are created to other portals within the
same tpgt and the sessions should have different isids.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I am not sure what happened. It looks like we have always leaked
the q->queue that is allocated from the kfifo_init call. nab finally
noticed that we were leaking and this patch fixes it by adding a
kfree call to iscsi_pool_free. kfifo_free is not used per kfifo_init's
instructions to use kfree.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
spin_lock functions take a pointer to the lock, not the lock itself.
This error was noticed by compiling ebsa110_defconfig for linux-rt where
the locking functions obviously are more picky about their arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Roel Kluin <12o3l@tiscali.nl>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver was updated for OMAP34xx, but the Kconfig file was missed.
So this adds the missing parts from d99241c in Tony Lindgren's tree:
Add watchdog timer support for TI OMAP3430.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add omap hsmmc controller for 2430 and 34xx.
Note that this controller has different registers compared to
the earlier omap MMC controller, so sharing code currently is
not possible.
Various updates and fixes from linux-omap list have been
merged into this patch.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old matching algorithm was too fuzzy, causing false positives.
For example, when asked for device D connection C1 and we only find
device D connection C2, we return that as a valid match despite the
connection names being different.
Change the algorithm such that:
An entry with a NULL ID is assumed to be a wildcard.
If an entry has a device ID, it must match
If an entry has a connection ID, it must match
However, we maintain the order of precidence while still only doing
a single pass over all entries: dev+con > dev only > con only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: David Brownell <dbrownell@users.sourceforge.net>
Subject: ARM/mach-davinci/usb.c buildfix
CC arch/arm/mach-davinci/usb.o
arch/arm/mach-davinci/usb.c:60: error: 'IRQ_USBINT' undeclared here (not in a function)
make[1]: *** [arch/arm/mach-davinci/usb.o] Error 1
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since dma.h has been moved to arch/arm/mach-s3c2410/include/mach,
use the new include path.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RTL8187 and RTL8187B devices can stall unless an explicit termination
packet is sent.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ieee80211_sta structure there is u64 supp_rates[IEEE80211_NUM_BANDS]
this is filled with all support rate from assoc_resp. If we associate
with G-band AP only supp_rates of G-band will be set the other band
supp_rates will be set to 0. If the user type this command
this will cause mac80211 to set to new channel, mac80211
does not disassociate in setting new channel, so the active
band is now A-band. then in handling the new essid mac80211 will
kick in the assoc steps which involve sending disassociation frame.
in this mac80211 will WARN_ON sta->supp_rates[A_BAND] == 0.
This fixes:
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1822http://www.kerneloops.org/searchweek.php?search=rs_get_rate
Signed-off-by: mohamed abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Artur Skawina confirmed that the first generation devices needs the same
URB_ZERO_PACKET flag, in oder to finish the pending transfer properly.
The second generation has been successfully fixed by
"p54usb: fix random traffic stalls (LM87)" (43af18f06d5)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 1058a75f07 ("xen: actually release
memory when shrinking domain") causes a crash if the page being released
is a highmem page.
If a page is highmem then there is no need to unmap it.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On -rt we were seeing spurious bad page states like:
Bad page state in process 'firefox'
page:c1bc2380 flags:0x40000000 mapping:c1bc2390 mapcount:0 count:0
Trying to fix it up, but a reboot is needed
Backtrace:
Pid: 503, comm: firefox Not tainted 2.6.26.8-rt13 #3
[<c043d0f3>] ? printk+0x14/0x19
[<c0272d4e>] bad_page+0x4e/0x79
[<c0273831>] free_hot_cold_page+0x5b/0x1d3
[<c02739f6>] free_hot_page+0xf/0x11
[<c0273a18>] __free_pages+0x20/0x2b
[<c027d170>] __pte_alloc+0x87/0x91
[<c027d25e>] handle_mm_fault+0xe4/0x733
[<c043f680>] ? rt_mutex_down_read_trylock+0x57/0x63
[<c043f680>] ? rt_mutex_down_read_trylock+0x57/0x63
[<c0218875>] do_page_fault+0x36f/0x88a
This is the case where a concurrent fault already installed the PTE and
we get to free the newly allocated one.
This is due to pgtable_page_ctor() doing the spin_lock_init(&page->ptl)
which is overlaid with the {private, mapping} struct.
union {
struct {
unsigned long private;
struct address_space *mapping;
};
spinlock_t ptl;
struct kmem_cache *slab;
struct page *first_page;
};
Normally the spinlock is small enough to not stomp on page->mapping, but
PREEMPT_RT=y has huge 'spin'locks.
But lockdep kernels should also be able to trigger this splat, as the
lock tracking code grows the spinlock to cover page->mapping.
The obvious fix is calling pgtable_page_dtor() like the regular pte free
path __pte_free_tlb() does.
It seems all architectures except x86 and nm10300 already do this, and
nm10300 doesn't seem to use pgtable_page_ctor(), which suggests it
doesn't do SMP or simply doesnt do MMU at all or something.
Signed-off-by: Peter Zijlstra <a.p.zijlsta@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Add wrapper functions for the following compat system calls:
* readahead
* sendfile64
* tkill
* tgkill
* keyctl
This ensures that the high order bits of the parameter registers are correctly
sign extended.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Precreate stop_machine threads in case the machine supports ETR/STP.
Otherwise we might deadlock if a time sync operation gets scheduled
and the creation of stop_machine threads would cause disk I/O.
This is just the minimal fix.
The real fix would be to only precreate stop_machine threads if
ETR/STP is actually used. But that would be a rather large and
complicated patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Thomas Reitmayr
Mark Lord
Tejun Heo
Ingo Molnar
Eric Anholt
David S. Miller
Timo Teras
Alex Williamson
Heiko Carstens
Philipp Zabel
Russell King
Brian King
Andrew Vasquez
Seokmann Ju
Joe Carnuccio
Lalit Chandivade
Anirban Chakraborty
Mike Christie
Uwe Kleine-König
Madhusudhan Chikkature
Jean-Christop PLAGNIOL-VILLARD
David Brownell
Ramax Lo
Larry Finger
Abbas, Mohamed
Christian Lamparter
Ian Campbell
Peter Zijlstra
Takashi Iwai
Michael Holzheu