Errata ERR050568 description says that "Flash access by FlexSPI AHB
command may not work with platform frequency equal to 300 MHz" on
LS1028A.
By default, smaller length reads(equal to RX FIFO size) are done by IP
bus and larger length reads using AHB bus. For adding errata workaround,
use IP bus to read entire flash contents and disable AHB path when
platform frequency is 300Mhz.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-5-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver support for imx8dxl which support read through IP bus only
and disable AHB bus due to an IC errata. Use the pre-defined quirk
FSPI_QUIRK_USE_IP_ONLY directly in device-type data to disable AHB read.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-4-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for disabling AHB bus and read entire flash contents via IP
bus only. Please note, this enables IP bus read using a quirk which can
be enabled directly in device-type data or in existence of an errata
where AHB bus may need to be disabled.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-2-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Given the case that bootloader(such as UEFI)'s FSPI driver might not
handle all interrupts before loading kernel, those legacy interrupts
would assert immidiately once kernel's FSPI driver enable them. Further,
if it was FSPI_INTR_IPCMDDONE, the irq handler nxp_fspi_irq_handler()
would call complete(&f->c) to notify others. However, f->c might not be
initialized yet at that time, then cause kernel panic.
Of cause, we should fix this issue within bootloader. But it would be
better to have this pacth to make dirver more robust (by clearing all
interrupt status bits before enabling interrupts).
Suggested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201123025715.14635-1-ran.wang_1@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently NXP fspi driver has support of DT only. Adding ACPI
support to the driver so that it can be used by UEFI firmware
booting in ACPI mode. This driver will be probed if any firmware
will expose HID "NXP0009" in DSDT table.
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Link: https://lore.kernel.org/r/20200911130331.6313-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_get_resource_byname() function returns NULL on error, it
doesn't return error pointers.
Fixes: d166a73503 ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200312113154.GC20562@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply patch from NXP upstream repo to
Enable the octal combination mode in MCR0
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-3-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply patch from NXP upstream repo to
dynamically allocate AHB memory as needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-2-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull in this patch from NXP's upstream repo to
enable fspi on imx8qxp and imx8mm
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-1-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MODULE_LICENSE info to fix below warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/spi/spi-nxp-fspi.o
Typo fix in Boris Brezillon last name.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add octal mode flags for octal I/O data transfer support.
NXP FlexSPI controller supports 8 lines Rx/Tx data transfer.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add driver for NXP FlexSPI host controller
(0) What is the FlexSPI controller?
FlexSPI is a flexsible SPI host controller which supports two SPI
channels and up to 4 external devices. Each channel supports
Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional
data lines) i.e. FlexSPI acts as an interface to external devices,
maximum 4, each with up to 8 bidirectional data lines.
It uses new SPI memory interface of the SPI framework to issue
flash memory operations to up to four connected flash
devices (2 buses with 2 CS each).
(1) Tested this driver with the mtd_debug and JFFS2 filesystem utility
on NXP LX2160ARDB and LX2160AQDS targets.
LX2160ARDB is having two NOR slave device connected on single bus A
i.e. A0 and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses
one flash on A0 and second on B1 i.e. (CS0 and CS3).
Verified this driver on following SPI NOR flashes:
Micron, mt35xu512ab, [Read - 1 bit mode]
Cypress, s25fl512s, [Read - 1/2/4 bit mode]
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Heiko Schocher
Kuldeep Singh
Han Xu
Ran Wang
kuldip dwivedi
Dan Carpenter
Michael Walle
Chuhong Yuan
Stephen Boyd
Yogesh Narayan Gaur