Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.
Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64e2 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.
That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.
Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.
Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().
However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.
In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.
Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.
Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.
For example, let's consider the following scenario on a system
with HZ=1000:
* The synflood timestamp is 0, either because that's the timestamp
of the last synflood or, more commonly, because we're working with
a freshly created socket.
* We receive a new SYN, which triggers synflood protection. Let's say
that this happens when jiffies == 2147484649 (that is,
'synflood timestamp' + HZ + 2^31 + 1).
* Then tcp_synq_overflow() doesn't update the synflood timestamp,
because time_after32(2147484649, 1000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 1000: the value of 'last_overflow' + HZ.
* A bit later, we receive the ACK completing the 3WHS. But
cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
says that we're not under synflood. That's because
time_after32(2147484649, 120000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.
Of course, in reality jiffies would have increased a bit, but this
condition will last for the next 119 seconds, which is far enough
to accommodate for jiffie's growth.
Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.
Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.
Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.
For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit
cca9bab1b7 ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.
Fixes: cca9bab1b7 ("tcp: use monotonic timestamps for PAWS")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.
When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.
Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.
Fixes: 4d12ba4278 ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit 5c72299fba ("net: sched: cls_flower: Classify
packets using port ranges") had added filtering based on port ranges
to tc flower. However the commit missed necessary changes in hw-offload
code, so the feature gave rise to generating incorrect offloaded flow
keys in NIC.
One more detailed example is below:
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 100-200 action drop
With the setup above, an exact match filter with dst_port == 0 will be
installed in NIC by hw-offload. IOW, the NIC will have a rule which is
equivalent to the following one.
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 0 action drop
The behavior was caused by the flow dissector which extracts packet
data into the flow key in the tc flower. More specifically, regardless
of exact match or specified port ranges, fl_init_dissector() set the
FLOW_DISSECTOR_KEY_PORTS flag in struct flow_dissector to extract port
numbers from skb in skb_flow_dissect() called by fl_classify(). Note
that device drivers received the same struct flow_dissector object as
used in skb_flow_dissect(). Thus, offloaded drivers could not identify
which of these is used because the FLOW_DISSECTOR_KEY_PORTS flag was
set to struct flow_dissector in either case.
This patch adds the new FLOW_DISSECTOR_KEY_PORTS_RANGE flag and the new
tp_range field in struct fl_flow_key to recognize which filters are applied
to offloaded drivers. At this point, when filters based on port ranges
passed to drivers, drivers return the EOPNOTSUPP error because they do
not support the feature (the newly created FLOW_DISSECTOR_KEY_PORTS_RANGE
flag).
Fixes: 5c72299fba ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Partially sent record cleanup path increments an SG entry
directly instead of using sg_next(). This should not be a
problem today, as encrypted messages should be always
allocated as arrays. But given this is a cleanup path it's
easy to miss was this ever to change. Use sg_next(), and
simplify the code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like when BPF support was added by commit d3b18ad31f
("tls: add bpf support to sk_msg handling") and
commit d829e9c411 ("tls: convert to generic sk_msg interface")
it broke/removed the support for in-place crypto as added by
commit 4e6d47206c ("tls: Add support for inplace records
encryption").
The inplace_crypto member of struct tls_rec is dead, inited
to zero, and sometimes set to zero again. It used to be
set to 1 when record was allocated, but the skmsg code doesn't
seem to have been written with the idea of in-place crypto
in mind.
Since non trivial effort is required to bring the feature back
and we don't really have the HW to measure the benefit just
remove the left over support for now to avoid confusing readers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"This is mostly to fix the iwlwifi regression:
1) Flush GRO state properly in iwlwifi driver, from Alexander Lobakin.
2) Validate TIPC link name with properly length macro, from John
Rutherford.
3) Fix completion init and device query timeouts in ibmvnic, from
Thomas Falcon.
4) Fix SKB size calculation for netlink messages in psample, from
Nikolay Aleksandrov.
5) Similar kind of fix for OVS flow dumps, from Paolo Abeni.
6) Handle queue allocation failure unwind properly in gve driver, we
could try to release pages we didn't allocate. From Jeroen de
Borst.
7) Serialize TX queue SKB list accesses properly in mscc ocelot
driver. From Yangbo Lu"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net:
net: usb: aqc111: Use the correct style for SPDX License Identifier
net: phy: Use the correct style for SPDX License Identifier
net: wireless: intel: iwlwifi: fix GRO_NORMAL packet stalling
net: mscc: ocelot: use skb queue instead of skbs list
net: mscc: ocelot: avoid incorrect consuming in skbs list
gve: Fix the queue page list allocated pages count
net: inet_is_local_reserved_port() port arg should be unsigned short
openvswitch: fix flow command message size
net: phy: dp83869: Fix return paths to return proper values
net: psample: fix skb_over_panic
net: usbnet: Fix -Wcast-function-type
net: hso: Fix -Wcast-function-type
net: port < inet_prot_sock(net) --> inet_port_requires_bind_service(net, port)
ibmvnic: Serialize device queries
ibmvnic: Bound waits for device queries
ibmvnic: Terminate waiting device threads after loss of service
ibmvnic: Fix completion structure initialization
net-sctp: replace some sock_net(sk) with just 'net'
net: Fix a documentation bug wrt. ip_unprivileged_port_start
tipc: fix link name length check
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
Any argument outside of that range would result in an out of bound
memory access, since the accessed array is 65536 bits long.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that the sysctl write accessor functions guarantee that:
net->ipv4.sysctl_ip_prot_sock <= net->ipv4.ip_local_ports.range[0]
invariant is maintained, and as such the max() in selinux hooks is actually spurious.
ie. even though
if (snum < max(inet_prot_sock(sock_net(sk)), low) || snum > high) {
per logic is the same as
if ((snum < inet_prot_sock(sock_net(sk)) && snum < low) || snum > high) {
it is actually functionally equivalent to:
if (snum < low || snum > high) {
which is equivalent to:
if (snum < inet_prot_sock(sock_net(sk)) || snum < low || snum > high) {
even though the first clause is spurious.
But we want to hold on to it in case we ever want to change what what
inet_port_requires_bind_service() means (for example by changing
it from a, by default, [0..1024) range to some sort of set).
Test: builds, git 'grep inet_prot_sock' finds no other references
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:
1) Support alternative names for network devices, from Jiri Pirko.
2) Introduce per-netns netdev notifiers, also from Jiri Pirko.
3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.
4) Allow compiling out the TLS TOE code, from Jakub Kicinski.
5) Add several new tracepoints to the kTLS code, also from Jakub.
6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.
7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.
8) Add XDP support to mvneta driver, from Lorenzo Bianconi.
9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.
10) PTP support for aquantia chips, from Egor Pomozov.
11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.
12) Add smart nagle to tipc, from Jon Maloy.
13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.
14) Add a flow mask cache to OVS, from Tonghao Zhang.
15) Add XDP support to ice driver, from Maciej Fijalkowski.
16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.
17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.
18) Support it in stmmac driver too, from Jose Abreu.
19) Support TIPC encryption and auth, from Tuong Lien.
20) Introduce BPF trampolines, from Alexei Starovoitov.
21) Make page_pool API more numa friendly, from Saeed Mahameed.
22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.
23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...
Pull cgroup updates from Tejun Heo:
"There are several notable changes here:
- Single thread migrating itself has been optimized so that it
doesn't need threadgroup rwsem anymore.
- Freezer optimization to avoid unnecessary frozen state changes.
- cgroup ID unification so that cgroup fs ino is the only unique ID
used for the cgroup and can be used to directly look up live
cgroups through filehandle interface on 64bit ino archs. On 32bit
archs, cgroup fs ino is still the only ID in use but it is only
unique when combined with gen.
- selftest and other changes"
* 'for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (24 commits)
writeback: fix -Wformat compilation warnings
docs: cgroup: mm: Fix spelling of "list"
cgroup: fix incorrect WARN_ON_ONCE() in cgroup_setup_root()
cgroup: use cgrp->kn->id as the cgroup ID
kernfs: use 64bit inos if ino_t is 64bit
kernfs: implement custom exportfs ops and fid type
kernfs: combine ino/id lookup functions into kernfs_find_and_get_node_by_id()
kernfs: convert kernfs_node->id from union kernfs_node_id to u64
kernfs: kernfs_find_and_get_node_by_ino() should only look up activated nodes
kernfs: use dumber locking for kernfs_find_and_get_node_by_ino()
netprio: use css ID instead of cgroup ID
writeback: use ino_t for inodes in tracepoints
kernfs: fix ino wrap-around detection
kselftests: cgroup: Avoid the reuse of fd after it is deallocated
cgroup: freezer: don't change task and cgroups status unnecessarily
cgroup: use cgroup->last_bstat instead of cgroup->bstat_pending for consistency
cgroup: remove cgroup_enable_task_cg_lists() optimization
cgroup: pids: use atomic64_t for pids->limit
selftests: cgroup: Run test_core under interfering stress
selftests: cgroup: Add task migration tests
...
This patch is to fix a data-race reported by syzbot:
BUG: KCSAN: data-race in sctp_assoc_migrate / sctp_hash_obj
write to 0xffff8880b67c0020 of 8 bytes by task 18908 on cpu 1:
sctp_assoc_migrate+0x1a6/0x290 net/sctp/associola.c:1091
sctp_sock_migrate+0x8aa/0x9b0 net/sctp/socket.c:9465
sctp_accept+0x3c8/0x470 net/sctp/socket.c:4916
inet_accept+0x7f/0x360 net/ipv4/af_inet.c:734
__sys_accept4+0x224/0x430 net/socket.c:1754
__do_sys_accept net/socket.c:1795 [inline]
__se_sys_accept net/socket.c:1792 [inline]
__x64_sys_accept+0x4e/0x60 net/socket.c:1792
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8880b67c0020 of 8 bytes by task 12003 on cpu 0:
sctp_hash_obj+0x4f/0x2d0 net/sctp/input.c:894
rht_key_get_hash include/linux/rhashtable.h:133 [inline]
rht_key_hashfn include/linux/rhashtable.h:159 [inline]
rht_head_hashfn include/linux/rhashtable.h:174 [inline]
head_hashfn lib/rhashtable.c:41 [inline]
rhashtable_rehash_one lib/rhashtable.c:245 [inline]
rhashtable_rehash_chain lib/rhashtable.c:276 [inline]
rhashtable_rehash_table lib/rhashtable.c:316 [inline]
rht_deferred_worker+0x468/0xab0 lib/rhashtable.c:420
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
It was caused by rhashtable access asoc->base.sk when sctp_assoc_migrate
is changing its value. However, what rhashtable wants is netns from asoc
base.sk, and for an asoc, its netns won't change once set. So we can
simply fix it by caching netns since created.
Fixes: d6c0256a60 ("sctp: add the rhashtable apis for sctp global transport hashtable")
Reported-by: syzbot+e3b35fe7918ff0ee474e@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In commit a82055af59 ("netfilter: nft_payload: add VLAN offload
support"), VLAN fields in struct flow_dissector_key_vlan were unionized
with the intention of introducing another field that covered the whole TCI
header. However without a wrapping struct the subfields end up sharing the
same bits. As a result, "tc filter add ... flower vlan_id 14" specifies not
only vlan_id, but also vlan_priority.
Fix by wrapping the individual VLAN fields in a struct.
Fixes: a82055af59 ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit added the ability to throttle stations when they queue
too much airtime in the hardware. This commit enables the functionality by
calculating the expected airtime usage of each packet that is dequeued from
the TXQs in mac80211, and accounting that as pending airtime.
The estimated airtime for each skb is stored in the tx_info, so we can
subtract the same amount from the running total when the skb is freed or
recycled. The throttling mechanism relies on this accounting to be
accurate (i.e., that we are not freeing skbs without subtracting any
airtime they were accounted for), so we put the subtraction into
ieee80211_report_used_skb(). As an optimisation, we also subtract the
airtime on regular TX completion, zeroing out the value stored in the
packet afterwards, to avoid having to do an expensive lookup of the station
from the packet data on every packet.
This patch does *not* include any mechanism to wake a throttled TXQ again,
on the assumption that this will happen anyway as a side effect of whatever
freed the skb (most commonly a TX completion).
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-5-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix recently added code to calculate airtime of packets to the mt76
driver. Import this into mac80211 so we can use it for airtime queue limit
calculations.
The airtime.c file is copied verbatim from the mt76 driver, and adjusted to
be usable in mac80211. This involves:
- Switching to mac80211 data structures.
- Adding support for 160 MHz channels and HE mode.
- Moving the symbol and duration calculations around a bit to avoid
rounding with the higher rates and longer symbol times used for HE rates.
The per-rate TX rate calculation is also split out to its own function so
it can be used directly for the AQL calculations later.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-3-kyan@google.com
[fix HE_GROUP_IDX() to use 3 * bw, since there are 3 _gi values]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is alike the previous change, with some additional ipv4 specific
quirk. Even when using the route hint we still have to do perform
additional per packet checks about source address validity: a new
helper is added to wrap them.
Hints are explicitly disabled if the destination is a local broadcast,
that keeps the code simple and local broadcast are a slower path anyway.
UDP flood performances vs recvmmsg() receiver:
vanilla patched delta
Kpps Kpps %
1683 1871 +11
In the worst case scenario - each packet has a different
destination address - the performance delta is within noise
range.
v3 -> v4:
- re-enable hints for forward
v2 -> v3:
- really fix build (sic) and hint usage check
- use fib4_has_custom_rules() helpers (David A.)
- add ip_extract_route_hint() helper (Edward C.)
- use prev skb as hint instead of copying data (Willem)
v1 -> v2:
- fix build issue with !CONFIG_IP_MULTIPLE_TABLES
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it in the next patch.
Additionally constify the helper argument.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a per namespace counter, increment it on successful creation
of any route using the source address, decrement it on deletion
of such routes.
This allows us to check easily if the routing decision in the
current namespace depends on the packet source. Will be used
by the next patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wraps the namespace field with the same name, to easily
access it regardless of build options.
Suggested-by: David Ahern <dsahern@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the following parameters in order to add the possibility to sync
DMA memory for device before putting allocated pages in the page_pool
caches:
- PP_FLAG_DMA_SYNC_DEV: if set in page_pool_params flags, all pages that
the driver gets from page_pool will be DMA-synced-for-device according
to the length provided by the device driver. Please note DMA-sync-for-CPU
is still device driver responsibility
- offset: DMA address offset where the DMA engine starts copying rx data
- max_len: maximum DMA memory size page_pool is allowed to flush. This
is currently used in __page_pool_alloc_pages_slow routine when pages
are allocated from page allocator
These parameters are supposed to be set by device drivers.
This optimization reduces the length of the DMA-sync-for-device.
The optimization is valid because pages are initially
DMA-synced-for-device as defined via max_len. At RX time, the driver
will perform a DMA-sync-for-CPU on the memory for the packet length.
What is important is the memory occupied by packet payload, because
this is the area CPU is allowed to read and modify. As we don't track
cache-lines written into by the CPU, simply use the packet payload length
as dma_sync_size at page_pool recycle time. This also take into account
any tail-extend.
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add page_pool_update_nid() to be called by page pool consumers when they
detect numa node changes.
It will update the page pool nid value to start allocating from the new
effective numa node.
This is to mitigate page pool allocating pages from a wrong numa node,
where the pool was originally allocated, and holding on to pages that
belong to a different numa node, which causes performance degradation.
For pages that are already being consumed and could be returned to the
pool by the consumer, in next patch we will add a check per page to avoid
recycling them back to the pool and return them to the page allocator.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Match on ethertype and set up protocol dependency. Check for protocol
dependency before accessing the tci field. Allow to match on the
encapsulated ethertype too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware offload support at this stage assumes an ethernet device in
place. The flow dissector provides the intermediate representation to
express this selector, so extend it to allow to store the interface
type. Flower does not uses this, so skb_flow_dissect_meta() is not
extended to match on this new field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch constifies the pointer to source register data that is passed
as an input parameter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring back tls_sw_sendpage_locked. sk_msg redirection into a socket
with TLS_TX takes the following path:
tcp_bpf_sendmsg_redir
tcp_bpf_push_locked
tcp_bpf_push
kernel_sendpage_locked
sock->ops->sendpage_locked
Also update the flags test in tls_sw_sendpage_locked to allow flag
MSG_NO_SHARED_FRAGS. bpf_tcp_sendmsg sets this.
Link: https://lore.kernel.org/netdev/CA+FuTSdaAawmZ2N8nfDDKu3XLpXBbMtcCT0q4FntDD2gn8ASUw@mail.gmail.com/T/#t
Link: https://github.com/wdebruij/kerneltools/commits/icept.2
Fixes: 0608c69c9a ("bpf: sk_msg, sock{map|hash} redirect through ULP")
Fixes: f3de19af0f ("Revert \"net/tls: remove unused function tls_sw_sendpage_locked\"")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Jonathan change the page_pool to become responsible to its
own shutdown via deferred work queue, then the disconnect_cnt
counter was removed from xdp memory model tracepoint.
This patch change the page_pool_inflight tracepoint name to
page_pool_release, because it reflects the new responsability
better. And it reintroduces a counter that reflect the number of
times page_pool_release have been tried.
The counter is also used by the code, to only empty the alloc
cache once. With a stuck work queue running every second and
counter being 64-bit, it will overrun in approx 584 billion
years. For comparison, Earth lifetime expectancy is 7.5 billion
years, before the Sun will engulf, and destroy, the Earth.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Wildcard support for the net,iface set from Kristian Evensen.
2) Offload support for matching on the input interface.
3) Simplify matching on vlan header fields.
4) Add nft_payload_rebuild_vlan_hdr() function to rebuild the vlan
header from the vlan sk_buff metadata.
5) Pass extack to nft_flow_cls_offload_setup().
6) Add C-VLAN matching support.
7) Use time64_t in xt_time to fix y2038 overflow, from Arnd Bergmann.
8) Use time_t in nft_meta to fix y2038 overflow, also from Arnd.
9) Add flow_action_entry_next() helper function to flowtable offload
infrastructure.
10) Add IPv6 support to the flowtable offload infrastructure.
11) Support for input interface matching from postrouting,
from Phil Sutter.
12) Missing check for ndo callback in flowtable offload, from wenxu.
13) Remove conntrack parameter from flow_offload_fill_dir(), from wenxu.
14) Do not pass flow_rule object for rule removal, cookie is sufficient
to achieve this.
15) Release flow_rule object in case of error from the offload commit
path.
16) Undo offload ruleset updates if transaction fails.
17) Check for error when binding flowtable callbacks, from wenxu.
18) Always unbind flowtable callbacks when unregistering hooks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.
Disallow removing the pool until all pages are back, so the pool
is always available for page producers.
Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.
When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system. Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.
Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.
Fixes: d956a048cd ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_flow_rule_route_ipv6() and use it from the IPv6 and the inet
flowtable type definitions. Rename the nf_flow_rule_route() function to
nf_flow_rule_route_ipv4().
Adjust maximum number of actions, which now becomes 16 to leave
sufficient room for the IPv6 address mangling for NAT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.
The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.
The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ism module is unloaded return control from exit routine only,
if all link groups are freed.
If an IB device is thrown away return control from device removal only,
if all link groups belonging to this device are freed.
A counters for the total number of SMCD link groups per ISM device is
introduced. ism module unloading continues only if the total number of
SMCD link groups for all ISM devices is zero. ISM device
removal continues only it the total number of SMCD link groups per ISM
device has decreased to zero.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD link group termination is called when peer signals its shutdown
of its corresponding link group. For regular shutdowns no connections
exist anymore. For abnormal shutdowns connections must be killed and
their DMBs must be unregistered immediately. That means the SMCR method
to delay the link group freeing several seconds does not fit.
This patch adds immediate termination of a link group and its SMCD
connections and makes sure all SMCD link group related cleanup steps
are finished.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 'module' member in the 'struct vsock_transport'
in order to get/put the transport module. This prevents the
module unloading while sockets are assigned to it.
We increase the module refcnt when a socket is assigned to a
transport, and we decrease the module refcnt when the socket
is destructed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of multiple transports in the
VSOCK core.
With the multi-transports support, we can use vsock with nested VMs
(using also different hypervisors) loading both guest->host and
host->guest transports at the same time.
Major changes:
- vsock core module can be loaded regardless of the transports
- vsock_core_init() and vsock_core_exit() are renamed to
vsock_core_register() and vsock_core_unregister()
- vsock_core_register() has a feature parameter (H2G, G2H, DGRAM)
to identify which directions the transport can handle and if it's
support DGRAM (only vmci)
- each stream socket is assigned to a transport when the remote CID
is set (during the connect() or when we receive a connection request
on a listener socket).
The remote CID is used to decide which transport to use:
- remote CID <= VMADDR_CID_HOST will use guest->host transport;
- remote CID == local_cid (guest->host transport) will use guest->host
transport for loopback (host->guest transports don't support loopback);
- remote CID > VMADDR_CID_HOST will use host->guest transport;
- listener sockets are not bound to any transports since no transport
operations are done on it. In this way we can create a listener
socket, also if the transports are not loaded or with VMADDR_CID_ANY
to listen on all transports.
- DGRAM sockets are handled as before, since only the vmci_transport
provides this feature.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All transports call __vsock_create() with the same parameters,
most of them depending on the parent socket. In order to simplify
the VSOCK core APIs exposed to the transports, this patch adds
the vsock_create_connected() callable from transports to create
a new socket when a connection request is received.
We also unexported the __vsock_create().
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_transport and vmci_transport handle the buffer_size
sockopts in a very similar way.
In order to support multiple transports, this patch moves this
handling in the core to allow the user to change the options
also if the socket is not yet assigned to any transport.
This patch also adds the '.notify_buffer_size' callback in the
'struct virtio_transport' in order to inform the transport,
when the buffer_size is changed by the user. It is also useful
to limit the 'buffer_size' requested (e.g. virtio transports).
Acked-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now the 'struct vsock_sock' object contains a pointer to
the transport, this patch adds a parameter to the
vsock_core_get_transport() to return the right transport
assigned to the socket.
This patch modifies also the virtio_transport_get_ops(), that
uses the vsock_core_get_transport(), adding the
'struct vsock_sock *' parameter.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation to support multiple transports, this patch adds
the 'transport' member at the 'struct vsock_sock'.
This new field is initialized during the creation in the
__vsock_create() function.
This patch also renames the global 'transport' pointer to
'transport_single', since for now we're only supporting a single
transport registered at run-time.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This header file now only includes the "uapi/linux/vm_sockets.h".
We can include directly it when needed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) New generic devlink param "enable_roce", for downstream devlink
reload support
2) Do vport ACL configuration on per vport basis when
enabling/disabling a vport. This enables to have vports enabled/disabled
outside of eswitch config for future
3) Split the code for legacy vs offloads mode and make it clear
4) Tide up vport locking and workqueue usage
5) Fix metadata enablement for ECPF
6) Make explicit use of VF property to publish IB_DEVICE_VIRTUAL_FUNCTION
7) E-Switch and flow steering core low level support and refactoring for
netfilter flowtables offload
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-11-13
1) Remove a unnecessary net_exit function from the xfrm interface.
From Xin Long.
2) Assign xfrm4_udp_encap_rcv to a UDP socket only if xfrm
is configured. From Alexey Dobriyan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet
Guillaume Nault
John Hurley
Sabrina Dubroca
Yoshiki Komachi
Jakub Kicinski
Linus Torvalds
Maciej Żenczykowski
David S. Miller
Xin Long
Petr Machata
Toke Høiland-Jørgensen
Kan Yan
Paolo Abeni
Lorenzo Bianconi
Saeed Mahameed
Pablo Neira Ayuso
Willem de Bruijn
Jesper Dangaard Brouer
Jonathan Lemon
Vladimir Oltean
Ursula Braun
Stefano Garzarella