In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
-----BEGIN PGP SIGNATURE-----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=gDUI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some relatively small changes:
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides an alternative mechanism for AP VLAN support where a
single netdev is used with VLAN tagged frames instead of separate
netdevs for each VLAN without tagged frames from the WLAN driver.
By setting NL80211_EXT_FEATURE_VLAN_OFFLOAD flag the driver indicates
support for a single netdev with VLAN tagged frames. Separate
VLAN-specific netdevs can be added using RTM_NEWLINK/IFLA_VLAN_ID
similarly to Ethernet. NL80211_CMD_NEW_KEY (for group keys),
NL80211_CMD_NEW_STATION, and NL80211_CMD_SET_STATION will optionally
specify vlan_id using NL80211_ATTR_VLAN_ID.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20191031214640.5012-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.
Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.
Enable scan in mac80211 in these cases.
Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful for checking how much airtime is being used up by other
transmissions on the channel, e.g. by calculating (time_rx - time_bss_rx)
or (time_busy - time_bss_rx - time_tx)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190828102042.58016-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the data structure, policy and parsing code allowing userland to send
the OBSS PD information into the kernel.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.
General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.
Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.
Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Fixes: 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices")
Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ERR_PTR() is an inline, not a macro, just open-code it
here so it's usable as an initializer, fixing the build in
brcmfmac.
Reported-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Fixes: 901bb98918 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
This makes boot uniformly boottime and tai uniformly clocktai, to
address the remaining oversights.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20190621203249.3909-2-Jason@zx2c4.com
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cfg80211_remain_on_channel_expired is used to notify userspace when
the remain on channel duration expired by sending an event. There is
no such equivalent to CMD_FRAME, where if offchannel and a duration
is provided, the card will go offchannel for that duration. Currently
there is no way for userspace to tell when that duration expired
apart from setting an independent timeout. This timeout is quite
erroneous as the kernel may not immediately send out the frame
because of scheduling or work queue delays. In testing, it was found
this timeout had to be quite large to accomidate any potential delays.
A better solution is to have the kernel send an event when this
duration has expired. There is already NL80211_CMD_FRAME_WAIT_CANCEL
which can be used to cancel a NL80211_CMD_FRAME offchannel. Using this
command matches perfectly to how NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL
works, where its both used to cancel and notify if the duration has
expired.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a function that iterates over the BSS entries associated with a
given wiphy and calls a callback for each iterated BSS. This can be
used by drivers in various ways, e.g., to evaluate some property for
all the BSSs in the medium.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.
It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is similar to ieee80211_get_he_sta_cap() but allows passing
the iftype. Also make ieee80211_get_he_sta_cap() use the new helper
rather than duplicating the code.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let drivers advertise support for station-mode SAE authentication
offload with a new NL80211_EXT_FEATURE_SAE_OFFLOAD flag.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the BSS is expired during connection, the connect result will
trigger a kernel warning. Ideally cfg80211 should hold the BSS
before the connection is attempted, but as the BSSID is not known
in case of auth/assoc MLME offload (connect op) it doesn't.
For those drivers without the connect op cfg80211 holds down the
reference so it wil not be removed from list.
Fix this by removing the warning and silently adding the BSS back to
the bss list which is return by the driver (with proper BSSID set) or
in case the BSS is already added use that.
The requirements for drivers are documented in the API's.
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
[formatting fixes, keep old timestamp]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per the current design, in the case of sw crypto controlled devices,
it is the device which advertises the support for AP/VLAN iftype based
on it's ability to tranmsit packets encrypted in software
(In VLAN functionality, group traffic generated for a specific
VLAN group is always encrypted in software). Commit db3bdcb9c3
("mac80211: allow AP_VLAN operation on crypto controlled devices")
has introduced this change.
Since 4addr AP operation also uses AP/VLAN iftype, this conditional
way of advertising AP/VLAN support has broken 4addr AP mode operation on
crypto controlled devices which do not support VLAN functionality.
In the case of ath10k driver, not all firmwares have support for VLAN
functionality but all can support 4addr AP operation. Because AP/VLAN
support is not advertised for these devices, 4addr AP operations are
also blocked.
Fix this by allowing 4addr operation on devices which do not support
AP/VLAN iftype but can support 4addr AP operation (decision is based on
the wiphy flag WIPHY_FLAG_4ADDR_AP).
Cc: stable@vger.kernel.org
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support to allow mesh HWMP to measure link metrics on unexercised
direct mesh path by sending some data frames to other mesh points which
are not currently selected as a primary traffic path but only 1 hop away.
The absence of the primary path to the chosen node makes it necessary to
apply some form of marking on a chosen packet stream so that the packets
can be properly steered to the selected node for testing, and not by the
regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cfg80211_merge_profile() and ieee802_11_find_bssid_profile() are
a bit cleaner if we just pass the merged_ie pointer instead of a pointer
to the pointer.
This isn't a functional change, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to set transmit power setting type and transmit
power level attributes to NL80211_CMD_SET_STATION in order to facilitate
adjusting the transmit power level of a station associated to the AP.
The added attributes allow selection of automatic and limited transmit
power level, with the level defined in dBm format.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for IEEE 802.11-2016 "Extended Key ID for Individually
Addressed Frames".
Extend cfg80211 and nl80211 to allow pairwise keys to be installed for
Rx only, enable Tx separately and allow Key ID 1 for pairwise keys.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[use NLA_POLICY_RANGE() for NL80211_KEY_MODE]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3. Detect legacy split and print a net-rate limited warning,
since there is no ROI in supporting this probably non-existent
split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Subelement profile may specify element IDs it doesn't inherit
from the management frame. Support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This interface allows the host driver to offload OWE processing
to user space. This intends to support OWE (Opportunistic Wireless
Encryption) AKM by the drivers that implement SME but rely on the
user space for the cryptographic/OWE processing in AP mode. Such
drivers are not capable of processing/deriving the DH IE.
A new NL80211 command - NL80211_CMD_UPDATE_OWE_INFO is introduced
to send the request/event between the host driver and user space.
Driver shall provide the OWE info (MAC address and DH IE) of
the peer to user space for cryptographic processing of the DH IE
through the event. Accordingly, the user space shall update the
OWE info/DH IE to the driver.
Following is the sequence in AP mode for OWE authentication.
Driver passes the OWE info obtained from the peer in the
Association Request to the user space through the event
cfg80211_update_owe_info_event. User space shall process the
OWE info received and generate new OWE info. This OWE info is
passed to the driver through NL80211_CMD_UPDATE_OWE_INFO
request. Driver eventually uses this OWE info to send the
Association Response to the peer.
This OWE info in the command interface carries the IEs that include
PMKID of the peer if the PMKSA is still valid or an updated DH IE
for generating a new PMKSA with the peer.
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Sunil Dutt <usdutt@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[remove policy initialization - no longer exists]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for mesh airtime link metric attribute
NL80211_STA_INFO_AIRTIME_LINK_METRIC.
Signed-off-by: Narayanraddi Masti <team.nmasti@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds the support to specify the RSSI thresholds per
band for each match set. This enhances the current behavior which
specifies a single rssi_threshold across all the bands by
introducing the rssi_threshold_per_band. These per band rssi
thresholds are referred through NL80211_BAND_* (enum nl80211_band)
variables as attribute types. Such attributes/values per each
band are nested through NL80211_ATTR_SCHED_SCAN_MIN_RSSI.
These band specific rssi thresholds shall take precedence over
the current rssi_thold per match set.
Drivers indicate this support through
%NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD.
These per band rssi attributes/values does not specify
"default RSSI filter" as done by
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI to stay backward compatible.
That said, these per band rssi values have to be specified for
the corresponding matchset.
Signed-off-by: vamsi krishna <vamsin@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[rebase on refactoring, add policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wiphy_{err,warn}_ratelimited will be used by rt2x00
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, we may want to transport higher bandwidth data
through vendor events, and in that case sending it multicast
is a bad idea. Allow vendor events to be unicast.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends the NL80211_CMD_ASSOCIATE event case to report
NL80211_ATTR_REQ_IE similarly to what is already done with the
NL80211_CMD_CONNECT events if the driver provides this information. In
practice, this adds (Re)Association Request frame information element
reporting to mac80211 drivers for the cases where user space SME is
used.
This provides more information for user space to figure out which
capabilities were negotiated for the association. For example, this can
be used to determine whether HT, VHT, or HE is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix cfg80211_gen_new_bssid() to not rely on u64 modulo arithmetic,
which isn't needed since we really just want to mask there. Also,
clean it up to calculate the mask only once and use GENMASK_ULL()
instead of open-coding the mask calculation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the new IEs are generated, the multiple BSSID elements
are not saved. Save aside properties that are needed later
for PS.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parsing and exposing nontransmitted APs is problematic
when underlying HW doesn't support it. Do it only if
driver indicated support. Allow HE restriction as well,
since the HE spec defined the exact manner that Multiple
BSSID set should behave. APs that not support the HE
spec will have less predictable Multiple BSSID set
support/behavior
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the transmitted BSS and the non-trasmitted BSS list were
defined in struct cfg80211_internal_bss. Move them to struct cfg80211_bss
since mac80211 needs this info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently have a number of helpers to find elements that just
return a u8 *, change those to return a struct element and add
inlines to deal with the u8 * compatibility.
Note that the match behaviour is changed to start the natch at
the data, so conversion from _ie_match to _elem_match need to
be done carefully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the missing documentation that kernel-doc continually warns
about, to get rid of all that noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix spelling mistake in cfg80211.h: "lenght" -> "length".
The typo is also in the special comment block which
translates to documentation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 40cbfa9021 ("cfg80211/nl80211: Optional authentication
offload to userspace")' introduced authentication offload to user
space by the host drivers in station mode. This commit extends
the same for the AP mode too.
Extend NL80211_ATTR_EXTERNAL_AUTH_SUPPORT to also claim the
support of external authentication from the user space in AP mode.
A new flag parameter is introduced in cfg80211_ap_settings to
intend the same while "start ap".
Host driver to use NL80211_CMD_FRAME interface to transmit and
receive the authentication frames to / from the user space.
Host driver to indicate the flag NL80211_RXMGMT_FLAG_EXTERNAL_AUTH
while sending the authentication frame to the user space. This
intends to the user space that the driver wishes it to process
the authentication frame for certain protocols, though it had
initially advertised the support for SME functionality.
User space shall accordingly do the authentication and indicate
its final status through the command NL80211_CMD_EXTERNAL_AUTH.
Allow the command even if userspace doesn't include the attribute
NL80211_ATTR_SSID for AP interface.
Host driver shall continue with the association sequence and
indicate the STA connection status through cfg80211_new_sta.
To facilitate the host drivers in AP mode for matching the pmkid
by the stations during the association, NL80211_CMD_EXTERNAL_AUTH
is also enhanced to include the pmkid to drivers after
the authentication.
This pmkid can also be used in the STA mode to include in the
association request.
Also modify nl80211_external_auth to not mandate SSID in AP mode.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[remove useless nla_get_flag() usage]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kan Yan
David S. Miller
Gurumoorthi Gnanasambandhan
Geert Uytterhoeven
Aaron Komisar
Felix Fietkau
Alexei Avshalom Lazar
Ben Greear
John Crispin
Manikanta Pubbisetty
Johannes Berg
Linus Torvalds
Thomas Gleixner
Jason A. Donenfeld
James Prestwood
Ilan Peer
Chung-Hsien Hsu
Chaitanya Tata
Rajkumar Manoharan
Dan Carpenter
Ashok Raj Nagarajan
Alexander Wetzel
Sara Sharon
Sunil Dutt
Narayanraddi Masti
vamsi krishna
Stanislaw Gruszka
Jouni Malinen
Matteo Croce
Srinivas Dasari