AP mode operations are seriously affected if mac80211 runs through a
multi-second scan while the AP is trying to send Beacon frames on the
operation channel. While this could be implemented in a way that does
not cause too many problems, it is not very simple and will require
synchronization with Beacon frame scheduling in the drivers (scan one
channel at a time between Beacon frames). Furthermore, such scanning
takes quite a bit longer time and existing userspace applications
would be likely to timeout while waiting for the results.
For now, just refuse requests for new scans (SIOCSIWSCAN) when in AP
mode. In practice, this moves the rejection from iwl* drivers into
mac80211 to make it apply to every mac80211-based driver.
This issue shows up in associated stations getting disconnected when
something (e.g., Network Manager) requests a scan while the interface
is in AP mode. When doing this continuously (e.g., NM does it every 120
seconds), the network gets close to useless.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes sporadic firmware restarts when scanning while associated.
The firmware will quietly cancel a scan (while associated) if the dwell time
for a channel to be scanned is larger than the time it may stay away from the
operating channel (because of DTIM catching). Unfortunately the driver is not
notified about the canceled scan and therefore the scan watchdog timeout will
be hit and the driver causes a firmware restart which results in
disassociation. This mainly happens on passive channels which use a dwell time
of 120 whereas a typical beacon interval is around 100.
The patch changes the dwell time for passive channels to be slightly smaller
than the actual beacon interval to work around the firmware issue. Furthermore
the number of allowed beacon misses is increased from one to three as otherwise
most scans (while associated) won't complete successfully.
However scanning while associated will still fail in corner cases such as a
beacon intervals below 30.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When SLUB debugging is enabled in the kernel, and the boot command includes
the option "slub_debug=P", rtl8187 encounters a GPF due to a read-after-free
of a urb.
Following the example of changes in p54usb to fix the same problem, the code
has been modified to use the usb_anchor_urb() method. With this change, the
USB core handles the freeing of urb's.
This patch fixes the problem reported in Kernel Bugzilla #12185
(http://bugzilla.kernel.org/show_bug.cgi?id=12185).
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix these bugs found by sparse:
ath5k/pcu.c:1102:21: warning: restricted __le32 degrades to integer
ath5k/pcu.c:1102:13: warning: incorrect type in assignment (different base types)
ath5k/pcu.c:1102:13: expected restricted __le32 <noident>
ath5k/pcu.c:1102:13: got unsigned int
ath5k/pcu.c:1104:20: warning: restricted __le32 degrades to integer
ath5k/pcu.c:1104:13: warning: incorrect type in assignment (different base types)
ath5k/pcu.c:1104:13: expected restricted __le32 <noident>
ath5k/pcu.c:1104:13: got unsigned int
Changes-licensed-under: ISC
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hardware buffer should only be used from an interrupt. The
wireless event generation functions are called from a workqueue, so use
USER_BAP instead.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes an old FIXME in p54pci.c by moving the "queue full"
check into the common library, where we can deal with it properly.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ability of disabling qos from module params is not required anymore.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ability of disabling qos from module params is not required
anymore.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes second definition of FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME
in iwl-fh.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces personal emails with hopefully
always valid Intel Linux Wireless, which will be routed
to a current maintainer
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the newly introduced sta_notify_ps function,
which can be used to notify the driver about every power state
transition for all associated stations, by integrating its functionality
back into the original sta_notify callback.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alan Stern found several flaws in p54usb's implementation and annotated:
"usb_kill_urb() and similar routines do not expect an URB's completion
routine to deallocate it. This is almost obvious -- if the URB is deallocated
before the completion routine returns then there's no way for usb_kill_urb
to detect when the URB actually is complete."
This patch addresses all known limitations in the old implementation and fixes
khub's "use-after-freed" hang, when SLUB debug's poisoning option is enabled.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Cc: stable@kernel.org
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_complete_buf uses a BH version of spinlock and so releasing
the lock enables BH which is incorrect when called from sta_notify
callback as MAC80211 disables hardirqs before the driver callback
is called.
As ath_tx_complete_buf is shared between user and softirq context
using normal spinlock may not be appropriate. Though the proper
fix would be to cleanup the context properly in the driver code,
this would be an interim fix to avoid kernel warning.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure sparse checks endianness when run on mac80211/cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no driver that actually does fragmentation on the
device, and the callback is buggy (when it returns an error,
mac80211's fragmentation status is changed so reading the
frag threshold from userspace reads the new value despite
the error). Let's just remove it, if we really find some
hardware supporting it we can add it back later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looking at the RC algorithm this is no longer necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds #ifdef CONFIG_IWLWIFI_DEBUG in iwl_rx_reply_rx()
method in iwlwifi/iwl-rx.c) to avoid build error caused by "iwlwifi:
implement iwl_debug_report_frame for iwlagn".
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers will support this, obviously, but this forces them to
set it up properly.
(This includes the fix posted as "mac80211: fix ifmodes check" and
tested in wireless-testing by Hin-Tak and others. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting RX_ABORT/RX_DIS after MAC reset and clearing RX_ABORT/RX_DIS
after enbling RXE/RXDP to avoid rx frames with corrupted descriptor
status.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's a regression from the patch titled "ath9k: Use mac80211's band
macros and remove enum hal_freq_band". MAC80211 band macros can't be
mapped directly with our hal band enum.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the initvalues required for AR9285 chipset.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix two small bugs with HT frequency setting:
* HT is accepted even when the driver is incapable
* HT40 is accepted when the driver cannot do 40 MHz
(both on the selected band)
Also simplify the code a little.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mention more possible STA entries and document the atomic requirement.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Slow Antenna Diversity has been removed, these are remnants
of the old code.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A scan run after association would change sc_curmode which is
used to get the current rate table. This patch fixes it
by removing sc_curmode and setting the rate table in usage in cur_rate_table
on association.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The proper rate table wouldn't be used if a disassoc
happens and a new attempt is made to associate using
wpa_supplicant. This patch fixes it by storing the rate
table to be used on association.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like there are some issues in the current ath9k version as
far as staggered Beacon frame scheduling is concerned. This results in
Beacon frame timestamp being off by 25 milliseconds or so which can
cause issues with multicast power save buffering in AP mode. Some
client stations fail to receive multicast frames when there is this
large an offset between TBTT and actual Beacon transmission time.
Since ath9k does not yet support multiple BSSes anyway, the staggered
Beacon frame scheduling is just increasing the number of interrupts at
this point. The easiest fix for the timestamp offset is to disable
staggered Beacon frames for now. We need to redesign beacon.c anyway
when adding multi-BSS support with mac80211 since the existing code
depends on different mechanism for Beacon frame transmission.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a memory leak where AP mode did not free transmitted Beacon frame
skbs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patches removes unused variable (pm_state) from iwl-dev.h and
from iwl-3945.h. (wireless-testing tree)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch protects iwlwifi indirect mmio operations with rmb() and
wmb(). It makes sure CPU reordering won't affect our indirect mmio
access.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch merges implementation of iwl_poll_bit() and
iwl_poll_direct_bit() by letting the latter be a special case of
the former.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the misue of CSR_GP_CNTRL with CSR_RESET address
in polling the CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY bit in
iwl4965_apm_reset(). This causes "MAC in deep sleep" error sometimes.
The patch also fixes the timeout value and the iwl_poll_bit() return
value check.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the misuse of microsecond with millisecond in the
polling mechanism of the iwlwifi driver. The impact of this problem
is the unacceptable latency for the whole system (especially during
bringing down the wlan interface).
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make sure we use only CCK rate for B only network.
For 3945 driver, it sets REPLY_RATE_SCALE command every time
we connect to a new network. In this command we set for every
rate the number of try and next rate. The problem mac80211 reports
same mode for both B and G mode as IEEE80211_BAND_2GHZ which will cause
using invalid rate other than CCK in B only network. THis patch
on association will examine sta valid rate on association, if no
OFDM rate in valid available rates it considers it as B only mode so
we can set REPLY_RATE_SCALE command with valid B only network and only
choose CCK rate in rate scaling.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old version of this code was copied from 3945 and never updated. This patch
cleans up structs that do not apply and accounts for other changes from
3945->iwlagn (e.g., PHY info can come in a separate cmd response from the
ucode.)
Signed-off-by: Daniel Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_hw_config can return an error when the hardware
has rfkill enabled. A WARN_ON() is too harsh for this
failure as it is a valid scenario. Only comment this warning
as we would like to have it back when rfkill is integrated into
mac80211.
Also reintroduce propagation of error if ieee80211_hw_config fails
in ieee80211_config_beacon.
This patch partially reverts patch:
5f0387fc3337ca26f0745f945f550f0c3734960f
"mac80211: clean up ieee80211_hw_config errors"
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced by
"wireless: avoid some net/ieee80211.h vs. linux/ieee80211.h conflicts"
LEAP authentication algorithm identifier should be 128.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current wireless statistics for the RTL8187 poorly indicate the signal
strength and quality. With testing, I found that the AGC value is inversely
correlated with the strength as in the RTL8187B. By implementing a similar
calculation, much more code becomes common to the two devices.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dma_free_noncoherent() and dma_free_coherent() are missing calls to
plat_unmap_dma_mem(). This patch adds them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The header path in the help text for the RUNTIME_DEBUG config option is
obsolete and needs to be updated to match the new location of
architecture-specific header files. While at it, fix the spelling mistake.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jouni Malinen
Helmut Schaa
Larry Finger
Bob Copeland
David Kilroy
Christian Lamparter
Winkler, Tomas
Pavel Roskin
Senthil Balasubramanian
Johannes Berg
Rami Rosen
John W. Linville
Sujith
Zhu, Yi
Abbas, Mohamed
Halperin, Daniel C
Reinette Chatre
David Daney
Dmitri Vorobiev