Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Add support for LPTIMx_OUT triggers that can be found on some STM32
devices. These triggers can be used then by ADC or DAC.
Typical usage is to configure LPTimer as PWM output (via pwm-stm32-lp)
and have synchronised analog conversions with these triggers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
The kerneldoc description for the trig_readonly field of struct iio_dev
lacked a colon, leading to this doc build warning:
./include/linux/iio/iio.h:603: warning: No description found for parameter 'trig_readonly'
A similar issue for iio_trigger_set_immutable() in trigger.h yielded:
./include/linux/iio/trigger.h:151: warning: No description found for parameter 'indio_dev'
./include/linux/iio/trigger.h:151: warning: No description found for parameter 'trig'
Fix the formatting and silence the warnings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add output compare trigger sources available on some instances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STM32H7 timer triggers:
- Add new valids_table
- Introduce compatible, with configuration data
- Extend up to 15 timers, available on STM32H7
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
-----BEGIN PGP SIGNATURE-----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=imPz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.14 cycle.
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa286 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Devices, like stm32 timer, could be triggered by hardware events which
are not buffer or software events. However it could be necessary to
validate the triggers like it is done for buffer or event triggered modes.
This patch add a new INDIO_HARDWARE_TRIGGERED operating mode for this
kind of devices and allow this mode to register trigger consumer.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Extend the inkern api with functions for reading and writing ext_info
of iio channels.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for TRGO2 trigger that can be found on STM32F7.
Add additional master modes supported by TRGO2.
Register additional "tim[1/8]_trgo2" triggers for timer1 & timer8.
Detect TRGO2 timer capability (master mode selection 2).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software device creation will result in undefined
behaviour when configfs is built as a module since the configfs group for
the device not properly initialized.
Similar to commit b2f0c09664 ("iio: sw-trigger: Fix config group
initialization").
Fixes: 0f3a8c3f34 ("iio: Add support for creating IIO devices via configfs")
Reported-by: Miguel Robles <miguel.robles@farole.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tG0h
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-iio-pwm-4.11' into test
Immutable branch between MFD, IIO and PWM due for the v4.11 merge window
Pulled into IIO to allow follow up series of triggered capture for the
STM32 ADCs.
Timers IPs can be used to generate triggers for other IPs like
DAC or ADC.
Each trigger may result of timer internals signals like counter enable,
reset or edge, this configuration could be done through "master_mode"
device attribute.
Since triggers could be used by DAC or ADC their names are defined
in include/ nux/iio/timer/stm32-timer-trigger.h and is_stm32_iio_timer_trigger
function could be used to check if the trigger is valid or not.
"trgo" trigger have a "sampling_frequency" attribute which allow to configure
timer sampling frequency.
version 8:
- change kernel version from 4.10 to 4.11 in ABI documentation
version 7:
- remove all iio_device related code
- move driver into trigger directory
version 5:
- simplify tables of triggers
- only create an IIO device when needed
version 4:
- get triggers configuration from "reg" in DT
- add tables of triggers
- sampling frequency is enable/disable when writing in trigger
sampling_frequency attribute
- no more use of interruptions
version 3:
- change compatible to "st,stm32-timer-trigger"
- fix attributes access right
- use string instead of int for master_mode and slave_mode
- document device attributes in sysfs-bus-iio-timer-stm32
version 2:
- keep only one compatible
- use st,input-triggers-names and st,output-triggers-names
to know which triggers are accepted and/or create by the device
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
-----BEGIN PGP SIGNATURE-----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=yjUA
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
buffer.h supplies everything needed for devices using buffers.
buffer_impl.h supplies access to the internals as needed to write
a buffer implementation.
This was really motivated by the mess that turned up in the
kernel-doc documentation pulled in by the new sphinx docs.
It made it clear that our logical separations in headers were
generally terrible. The buffer case was easy to sort out without
greatly effecting drivers so here it is.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This is a precursor to the splitting of buffer.h into parts relevant
to buffer implementation vs those for devices using buffers.
struct buffer is about to become opaque as far as the header is
concerned.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
As a precursor to splitting buffer.h, lets make sure all drivers
include the relevant headers rather than relying on picking them
up from kfifo_buf.h.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Ancient legacy of me doing it wrong which it is nice to clear
up whilst we are here.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This is a necessary step in taking the buffer implementation
opaque.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This should make it easier to see how the structure is split into
public and private parts - reflected in the generated documentation.
Deliberately use /* instead of /** for the private elements to avoid
warnings when kernel-doc script runs.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Nothing outside of indiustrialio-buffer.c should be using this.
Requires a large amount of juggling of functions to avoid a
forward definition.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The LIS3LV02 has a special bit that need to be set to get the
read values left aligned. Before this patch we get gibberish
like this:
iio_generic_buffer -a -c10 -n lis3lv02dl_accel
(...)
0.000000 -0.010042 -0.642688 19155832931907
0.000000 -0.010042 -0.642688 19155858751073
Which is because we read a raw value for 1g as 64 which is
the nominal 1024 for 1g shifted 4 bits to the left by being
right-aligned rather than left aligned.
Since all other sensors are left aligned, add some code to
set the special DAS (data alignment setting) bit to 1 so that
the right value is now read like this:
iio_generic_buffer -a -c10 -n lis3lv02dl_accel
(...)
0.000000 -0.147095 -10.120135 24761614364956
-0.029419 -0.176514 -10.120135 24761631624540
The scaling was weird as well: we have a gain of 1000 for 1g
and 3000 for 6g. I don't even remember how I came up with the
old values but they are wrong.
Fixes: 3acddf74f8 ("iio: st-sensors: add support for lis3lv02d accelerometer")
Cc: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support to match st sensors using information passed from ACPI DST
tables.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Specifically a helper for reading the available maximum raw value of a
channel and a helper for forwarding read_avail requests for raw values
from one iio driver to an iio channel that is consumed.
These rather specific helpers are in turn built with generic helpers
making it easy to build more helpers for available values as needed.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A large number of attributes can only take a limited range of values.
Currently in IIO this is handled by directly registering additional
*_available attributes thus providing this information to userspace.
It is desirable to provide this information via the core for much the same
reason this was done for the actual channel information attributes in the
first place. If it isn't there, then it can only really be accessed from
userspace. Other in kernel IIO consumers have no access to what valid
parameters are.
Two forms are currently supported:
* list of values in one particular IIO_VAL_* format.
e.g. 1.300000 1.500000 1.730000
* range specification with a step size:
e.g. [1.000000 0.500000 2.500000]
equivalent to 1.000000 1.5000000 2.000000 2.500000
An addition set of masks are used to allow different sharing rules for the
*_available attributes generated.
This allows for example:
in_accel_x_offset
in_accel_y_offset
in_accel_offset_available.
We could have gone with having a specification for each and every
info_mask element but that would have meant changing the existing userspace
ABI. This approach does not.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
[forward ported, added some docs and fixed buffer overflows /peda]
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MCP47x6 chip supports selection of a voltage reference (VDD, VREF buffered
or unbuffered). MCP4725 doesn't have this feature thus the eventual setting
is ignored and user is warned.
The setting is stored only in the volatile memory of the chip. You need to
manually store it to the EEPROM of the chip via 'store_eeprom' sysfs entry.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use a standard framework to get the reference voltage. It is done that way
in the iio subsystem and it will simplify extending of the driver.
Structure mcp4725_platform_data is left undeleted because it used in the
next patch.
This change breaks the current users of the driver, but there is no
mainline user of struct mcp4725_platform_data.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver predates the availability of IIO_CHAN_INFO_SAMP_FREQ
attribute wherein usage has some advantages like it can be accessed by
in-kernel consumers as well as reduces the code size.
Therefore, use IIO_CHAN_INFO_SAMP_FREQ to implement the
sampling_frequency attribute instead of using IIO_DEV_ATTR_SAMP_FREQ()
macro.
Move code from the functions associated with IIO_DEV_ATTR_SAMP_FREQ()
into respective read and write hooks with the mask set to
IIO_CHAN_INFO_SAMP_FREQ.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add new macros: IIO_ATTR_RO, IIO_ATTR_WO, IIO_ATTR_RW,
IIO_DEVICE_ATTR_RO, IIO_DEVICE_ATTR_WO and IIO_DEVICE_ATTR_RW to reduce
the amount of boiler plate code that is needed for creating new
attributes. This mimics the *_RO, *_WO, and *_RW macros that are found
in include/linux/device.h and include/linux/sysfs.h.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The event_attrs field of iio_info structure is only initialized once
whenever an object of iio_info is created. After that this field
is never modified again anywhere in the kernel. So, declare event_attrs
field of iio_info as a const struct attribute_group.
Checked for occurences throughout the kernel using grep and
coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow access to underlying channel IIO_CHAN_INFO_OFFSET from a consumer.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some triggers can only be attached to the IIO device that corresponds to
the same physical device. Currently each driver that requires this
implements its own trigger validation function.
Introduce a new helper function called iio_trigger_validate_own_device()
that can be used to do this check. Having a common implementation avoids
code duplication and unnecessary boiler-plate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
-----BEGIN PGP SIGNATURE-----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=V1xL
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
This adds a helper function to the IIO trigger framework:
iio_trigger_using_own(): for an IIO device, this tells
whether the device is using itself as a trigger.
This is true if the indio device:
(A) supplies a trigger and
(B) has assigned its own buffer poll function to use this
trigger.
This helper function is good when constructing triggered,
buffered drivers that can either use its own hardware *OR*
an external trigger such as a HRTimer or even the trigger from
a totally different sensor.
Under such circumstances it is important to know for example
if the timestamp from the same trigger hardware should be used
when populating the buffer: if iio_trigger_using_own() is true,
we can use this timestamp, else we need to pick a unique
timestamp directly in the trigger handler.
For this to work of course IIO devices registering hardware
triggers must follow the convention to set the parent device
properly, as as well as setting the parent of the IIO device
itself.
When a new poll function is attached, we check if the parent
device of the IIO of the poll function is the same as the
parent device of the trigger and in that case we conclude that
the hardware is using itself as trigger.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add resource managed devm_iio_triggered_buffer_setup() and
devm_iio_triggered_buffer_cleanup() to automatically clean up triggered
buffers setup by IIO drivers, thus leading to simplified IIO drivers code.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add resource managed devm_iio_trigger_register() and
devm_iio_triger_unregister() to automatically clean up registered triggers
allocated by IIO drivers, thus leading to simplified IIO drivers code.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are times when an assigned trigger to a device shouldn't ever
change after intialization.
Examples of this being used is when an provider device has a trigger
that is assigned to an ADC, which uses it populate data into a callback
buffer.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add iio_channel_cb_get_iio_dev function to allow getting the
underlying iio_dev. This is useful for setting the trigger of the
consumer ADC device.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software trigger creation will result in undefined
behaviour when configfs is built as a mdoule since the configfs group for
the trigger is not properly initialized.
Fixes: b662f809d4 ("iio: core: Introduce IIO software triggers")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Greg Kroah-Hartman
Dragos Bogdan
Linus Torvalds
Fabrice Gasnier
Jonathan Corbet
Lorenzo Bianconi
Benjamin Gaignard
Peter Rosin
Lars-Peter Clausen
Jonathan Cameron
Linus Walleij
Shrirang Bagul
Tomas Novotny
Eva Rachel Retuya
Brian Masney
Bhumika Goyal
Matt Ranostay
Gregor Boirie