The Meilhaus ME-2000i and ME-2600i data acquisition cards supported by
the Comedi "me_daq" driver use the PLX PCI 9050 PCI Target bridge chip
affected by the bug that prevents the chip's local configuration
registers being read from BAR0 or BAR1 base addresses that are an odd
multiple of 128 bytes. Use the PLX PCI 9050 quirk handler for these
devices to re-allocate affected regions to a 256-byte boundary.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PLX PCI 9050 PCI Target bridge controller has a bug that prevents
its local configuration registers being read through BAR0 (memory) or
BAR1 (i/o) if the base address lies on an odd 128-byte boundary, i.e. if
bit 7 of the base address is non-zero. This bug is described in the PCI
9050 errata list, version 1.4, May 2005. It was fixed in the
pin-compatible PCI 9052, which can be distinguished from the PCI 9050 by
checking the revision in the PCI header, which is hard-coded for these
chips.
Workaround the problem by re-allocating the affected regions to a
256-byte boundary. Note that BAR0 and/or BAR1 may have been disabled
(size 0) during initialization of the PCI chip when its configuration is
read from a serial EEPROM.
Currently, the fix-up has only been used for devices with the default
vendor and device ID of the PLX PCI 9050. The PCI 9052 shares the same
default device ID as the PCI 9050 but they have different PCI revision
codes.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the driver takes care of state saving, don't touch any registers on it.
Optimus (dual-gpu) laptops seem to have their own form of D3cold, but
unfortunately enter it on normal D3 transitions via the ACPI callback.
So when we use runtime PM to transition to D3, the card disappears off
the PCI bus, however we then try to access registers on it in the
runtime suspend finish, which really doesn't work.
This patch checks whether the pci state is saved and doesn't attempt to hit
any registers after that point if it is.
(Looks okay to Rafael)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_ext_cfg_avail() doesn't use the "struct pci_dev *" passed to
it, and there's no requirement that a host bridge even be represented
by a pci_dev. This drops the pci_ext_cfg_avail() parameter.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 2dcfaf85 mistakenly dropped the "flags & PCI_EXP_FLAGS_SLOT" test,
so now we create hotplug slots even for PCIe port devices that don't
support hotplug. This patch fixes this problem.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=48981
Peter reported that /proc/bus/pci/??/??.? does not work for 3.6.
This is because the device configuration space registers are
not accessible if the corresponding parent bridge is suspended or
the device is put into D3cold state.
This is the same as /sys/bus/pci/devices/0000:??:??.?/config access
issue. So the function used to solve sysfs issue is used to solve
this issue.
This patch moves pci_config_pm_runtime_get()/_put() from pci/pci-sysfs.c
to pci/pci.c and makes them extern so they can be used by both the
sysfs and proc paths.
[bhelgaas: changelog, references, reporters]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=48981
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=49031
Reported-by: Forrest Loomis <cybercyst@gmail.com>
Reported-by: Peter <lekensteyn@gmail.com>
Reported-by: Micael Dias <kam1kaz3@gmail.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
It supports both PCI root bus and PCI bus under PCI bridge.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
So could use assign_unassigned_bus_res pci root bus add
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We have pci_assign_unassigned_bus_resources() in as global function now.
Move pci_rescan_bus() back to probe.c where it should be.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some actions during shutdown need device to be in D0 state, such as
MSI shutdown etc, so resume device before shutdown.
Without this patch, a device may not be enumerated after a kexec
because the corresponding bridge is not in D0, so that
configuration space of the device is not accessible.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
If a PCI device and its parents are put into D3cold, unbinding the
device will trigger deadlock as follow:
- driver_unbind
- device_release_driver
- device_lock(dev) <--- previous lock here
- __device_release_driver
- pm_runtime_get_sync
...
- rpm_resume(dev)
- rpm_resume(dev->parent)
...
- pci_pm_runtime_resume
...
- pci_set_power_state
- __pci_start_power_transition
- pci_wakeup_bus(dev->parent->subordinate)
- pci_walk_bus
- device_lock(dev) <--- deadlock here
If we do not do device_lock in pci_walk_bus, we can avoid deadlock.
Device_lock in pci_walk_bus is introduced in commit:
d71374dafb, corresponding email thread
is: https://lkml.org/lkml/2006/5/26/38. The patch author Zhang Yanmin
said device_lock is added to pci_walk_bus because:
Some error handling functions call pci_walk_bus. For example, PCIe
aer. Here we lock the device, so the driver wouldn't detach from the
device, as the cb might call driver's callback function.
So I fixed the deadlock as follows:
- remove device_lock from pci_walk_bus
- add device_lock into callback if callback will call driver's callback
I checked pci_walk_bus users one by one, and found only PCIe aer needs
device lock.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
CC: Zhang Yanmin <yanmin.zhang@intel.com>
It is main portion of pci_rescan_bus().
Separate it out and prepare to use it for PCI root bus hot add later.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make ACPI power management routines and PCI power management
routines depending on ACPI take device PM QoS flags into account
when deciding what power state to put the device into.
In particular, after this change acpi_pm_device_sleep_state() will
not return ACPI_STATE_D3_COLD as the deepest available low-power
state if PM_QOS_FLAG_NO_POWER_OFF is requested for the device and it
will not require remote wakeup to work for the device in the returned
low-power state if there is at least one PM QoS flags request for the
device, but PM_QOS_FLAG_REMOTE_WAKEUP is not requested for it.
Accordingly, acpi_pci_set_power_state() will refuse to put the
device into D3cold if PM_QOS_FLAG_NO_POWER_OFF is requested for it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Huang Ying <ying.huang@intel.com>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
* When hotplugging PCI devices in a PV guest we can allocate Xen-SWIOTLB later.
* Cleanup Xen SWIOTLB.
* Support pages out grants from HVM domains in the backends.
* Support wild cards in xen-pciback.hide=(BDF) arguments.
* Update grant status updates with upstream hypervisor.
* Boot PV guests with more than 128GB.
* Cleanup Xen MMU code/add comments.
* Obtain XENVERS using a preferred method.
* Lay out generic changes to support Xen ARM.
* Allow privcmd ioctl for HVM (used to do only PV).
* Do v2 of mmap_batch for privcmd ioctls.
* If hypervisor saves the LED keyboard light - we will now instruct the kernel
about its state.
Fixes:
* More fixes to Xen PCI backend for various calls/FLR/etc.
* With more than 4GB in a 64-bit PV guest disable native SWIOTLB.
* Fix up smatch warnings.
* Fix up various return values in privmcmd and mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQaY8qAAoJEFjIrFwIi8fJwPMH+gKngf4vSqrHjw+V2nsmeYaw
zrhRQrm3xV4BNR7yQHs+InDst/AJRAr0GjuReDK4BqDEzUfcFKvzalspdMGGqf+W
MUp+pMdN2S6649r/KMFfPCYcQvmIkFu8l76aClAqfA77SZRv1VL2Gn9eBxd82jS0
sWAUu5ichDSdfm/vAKXhdvhlKsK0hmihEbCM3+wRBoXEJX0kKbhEGn82smaLqkEt
uxWDJBT4nyYqbm6KVXQJ/WYCaWEmEImGSDb9J1WeqftGEn1Q55mpknvElkpNPE1b
Ifayqk50Kt43qnLk/AUrm8KFFlNKb73wTyAb0hVw7SQDcw1AcLa8ZdohLIZOl/4=
=prMY
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"Features:
- When hotplugging PCI devices in a PV guest we can allocate
Xen-SWIOTLB later.
- Cleanup Xen SWIOTLB.
- Support pages out grants from HVM domains in the backends.
- Support wild cards in xen-pciback.hide=(BDF) arguments.
- Update grant status updates with upstream hypervisor.
- Boot PV guests with more than 128GB.
- Cleanup Xen MMU code/add comments.
- Obtain XENVERS using a preferred method.
- Lay out generic changes to support Xen ARM.
- Allow privcmd ioctl for HVM (used to do only PV).
- Do v2 of mmap_batch for privcmd ioctls.
- If hypervisor saves the LED keyboard light - we will now instruct
the kernel about its state.
Fixes:
- More fixes to Xen PCI backend for various calls/FLR/etc.
- With more than 4GB in a 64-bit PV guest disable native SWIOTLB.
- Fix up smatch warnings.
- Fix up various return values in privmcmd and mm."
* tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (48 commits)
xen/pciback: Restore the PCI config space after an FLR.
xen-pciback: properly clean up after calling pcistub_device_find()
xen/vga: add the xen EFI video mode support
xen/x86: retrieve keyboard shift status flags from hypervisor.
xen/gndev: Xen backend support for paged out grant targets V4.
xen-pciback: support wild cards in slot specifications
xen/swiotlb: Fix compile warnings when using plain integer instead of NULL pointer.
xen/swiotlb: Remove functions not needed anymore.
xen/pcifront: Use Xen-SWIOTLB when initting if required.
xen/swiotlb: For early initialization, return zero on success.
xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used.
xen/swiotlb: Move the error strings to its own function.
xen/swiotlb: Move the nr_tbl determination in its own function.
xen/arm: compile and run xenbus
xen: resynchronise grant table status codes with upstream
xen/privcmd: return -EFAULT on error
xen/privcmd: Fix mmap batch ioctl error status copy back.
xen/privcmd: add PRIVCMD_MMAPBATCH_V2 ioctl
xen/mm: return more precise error from xen_remap_domain_range()
xen/mmu: If the revector fails, don't attempt to revector anything else.
...
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJQa1rRAAoJEKhOf7ml8uNsYZ0P/2RZ71sgLWcUCfr0yHaiZeOd
2GxEYSZ+9BZJHADgoAK/bHRTv8crm40Y2RkbaWbxPDRNuE4SutbvNTGTlJSAguSD
yHkU/6AFC7u8Jwq+afsWIdGX7eHd78zPpj6EVtVtjHM903WDwbMU2vUz7tQ+fFa+
ZZ7eydq9j0ec0OoH3UeNhet7JSOpT5BSLgjmIkHMBgIvTxNVDbkB31QUxnUxocxn
k6S2wQaUSJJWGMLksRRNrhwLq+cGYwTsaOtG/KzRLH1raUyn33B5pcZr0aqhOkjg
ClaCks3V8o3vRghSwOPB5aVXzjBKvM3UnSyJNIl+FeCeyWuwSNbkEFdA/e7oPuxG
UsW6dcHiuVo6Ir4+zhd9+lN+/AcPTChO5b7lbU8qRF4ce04czWlUY/KzJjaM+YOE
CKGq6eX9AHwFjE+h4+VcCXgmzcioiS8Y/CPz13u8N1y0zzwW+ftjb12K+7lVBEG1
fhrePKHgLw3kJ9LqGpR+4vVur7C+rCf6WwCReTY2vXXVYJ+SuKWTRI4zAjTPXtHa
i9dpMRASpF+ScRYBcgwIpv789WuHATFKqdBSinZUKBaxQZ5flJ2qIrfqN5VeAejh
oQs/zZCdIuAtFKqVycQ0L42YxFNKgPFKQErUCSu3M5OuZLlLVLu7yQvIo2Xmo9qf
Hcrpvo5K+w29YkiwGP9e
=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
Commit 0d52f54e2e (PCI / ACPI: Make acpiphp
ignore root bridges using PCIe native hotplug) added code that made the
acpiphp driver completely ignore PCIe root complexes for which the kernel
had been granted control of the native PCIe hotplug feature by the BIOS
through _OSC. Later commit 619a5182d1
"PCI hotplug: Always allow acpiphp to handle non-PCIe bridges" relaxed
the constraints to allow acpiphp driver handle non-PCIe bridges under
such a complex. The constraint needs to be relaxed further to allow
acpiphp driver to handle PCIe ports without native PCIe hotplug capability.
Some MR-IOV switch chipsets, such PLX8696, support multiple virtual PCIe
switches and may migrate downstream ports among virtual switches. To
migrate a downstream port from the source virtual switch to the target, the
port needs to be hot-removed from the source and hot-added into the target.
The pciehp driver can't be used here because there are no slots within the
virtual PCIe switch. So acpiphp driver is used to support downstream port
migration. A typical configuration is as below:
[Root without native PCIe HP]
[Upstream port of vswitch without native PCIe HP]
[Downstream port of vswitch with native PCIe HP]
[PCIe endpoint]
Here acpiphp driver will be used to handle root ports and upstream port
in the virtual switch, and pciehp driver will be used to handle downstream
ports in the virtual switch.
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch changes .add/.remove interfaces of acpi_pci_driver.
In the current implementation acpi_handle is passed as a parameter
of .add/.remove interface. However, the acpi_pci_root structure
contains more useful information than just the acpi_handle. This
enables us to avoid some useless lookups in each acpi_pci_driver.
Note: This changes interfaces used by acpi_pci_register_driver(), an
exported symbol. This patch updates all the in-kernel users, but any
out-of-kernel acpi_pci_register_driver() users will need updates.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* stable/late-swiotlb.v3.3:
xen/swiotlb: Fix compile warnings when using plain integer instead of NULL pointer.
xen/swiotlb: Remove functions not needed anymore.
xen/pcifront: Use Xen-SWIOTLB when initting if required.
xen/swiotlb: For early initialization, return zero on success.
xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used.
xen/swiotlb: Move the error strings to its own function.
xen/swiotlb: Move the nr_tbl determination in its own function.
swiotlb: add the late swiotlb initialization function with iotlb memory
xen/swiotlb: With more than 4GB on 64-bit, disable the native SWIOTLB.
xen/swiotlb: Simplify the logic.
Conflicts:
arch/x86/xen/pci-swiotlb-xen.c
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This restores the previous behavior of stopping all child devices before
removing any of them. The current SR-IOV design, where removing the PF
also drops references on all the VFs, depends on having the VFs continue
to exist after having been stopped.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 433efd2247.
When we remove an SR-IOV device, we have this call chain:
driver .remove() method
pci_disable_sriov()
sriov_disable()
virtfn_remove()
pci_get_domain_bus_and_slot()
sriov_disable() is only called for PFs, not for VFs. When it's called
for a PF, it loops through all the VFs and calls virtfn_remove() for
each. But we stop and remove VFs before PFs, so by the time we get
to virtfn_remove(), the VFs have already been stopped and deleted
from the device list. Now pci_get_domain_bus_and_slot(), which uses
bus_find_device() and relies on that device list, doesn't find the
VFs, so the VF references aren't released correctly.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch (as1591) moves the pm_runtime_get_noresume() and
pm_runtime_put_sync() calls from __device_suspend() and
device_resume() to device_prepare() and device_complete() in the PM
core.
The reason for doing this is to make sure that parent devices remain
at full power (i.e., don't go into runtime suspend) while their
children are being resumed from a system sleep.
The PCI core already contained equivalent code to serve the same
purpose. The patch removes the duplicated code, since it is no longer
needed. One of the comments from the PCI core gets moved into the PM
core, and a second comment is added to explain whe the _get_noresume
and _put_sync calls are present.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Most architectures implement this in exactly the same way. Instead of
having each architecture duplicate this function, provide a single
implementation in the core and make it a weak symbol so that it can be
overridden on architectures where it is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the __init annotations in order to keep pci_fixup_irqs() around
after init (e.g. for hotplug). This requires the same change for the
implementation of pcibios_update_irq() on all architectures. While at
it, all __devinit annotations are removed as well, since they will be
useless now that HOTPLUG is always on.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Should use struct pci_bus_resource instead of struct pci_host_bridge_window
Commit 45ca9e9730 ("PCI: add helpers for building PCI bus resource lists")
added pci_free_resource_list() and used it in pci_bus_remove_resources().
Later it was also used for host bridge aperture lists, which was fine until
commit 0efd5aab41 ("PCI: add struct pci_host_bridge_window with CPU/bus
address offset"). That commit added offset information, so we needed a
struct pci_host_bridge_window that was separate from struct
pci_bus_resource.
Commit 0efd5aab41 should have split the host bridge aperture users of
pci_free_resource_list() from the pci_bus_resource user
(pci_bus_remove_resources()), but it did not.
[bhelgaas: changelog -- 0efd5aab41 was mine, so this is all my fault]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For bridges with "secondary > subordinate", i.e., invalid bus number
apertures, we don't enumerate anything behind the bridge unless the
user specified "pci=assign-busses".
This patch makes us automatically try to reassign the downstream bus
numbers in this case (just for that bridge, not for all bridges as
"pci=assign-busses" does).
We don't discover all the devices on the Intel DP43BF motherboard
without this change (or "pci=assign-busses") because its BIOS configures
a bridge as:
pci 0000:00:1e.0: PCI bridge to [bus 20-08] (subtractive decode)
[bhelgaas: changelog, change message to dev_info]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18412
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=625754
Reported-by: Brian C. Huffman <bhuffman@graze.net>
Reported-by: VL <vl.homutov@gmail.com>
Tested-by: VL <vl.homutov@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Function eeh_rmv_from_parent_pe() could be called by the path of
either normal PCI hotplug, or EEH recovery. For the former case,
we need purge the corresponding PE on removal of the associated
PE bus.
The patch tries to cover that by passing more information to function
pcibios_remove_pci_devices() so that we know if the corresponding PE
needs to be purged or be marked as "invalid".
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* pci/jiang-get-domain-bus-slot:
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
PCI: Use hotplug-safe pci_get_domain_bus_and_slot()
PCI/cpcihp: Use hotplug-safe pci_get_domain_bus_and_slot()
PCI/vga: Use hotplug-safe pci_get_domain_bus_and_slot()
ia64/PCI: Use hotplug-safe pci_get_domain_bus_and_slot()
This patch removes hardcoded sysfs attributes manipulation and
converts them into generic pci_bus->drv_attrs. This saves several bytes.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We piggyback on "xen/swiotlb: Use the swiotlb_late_init_with_tbl to init
Xen-SWIOTLB late when PV PCI is used." functionality to start up
the Xen-SWIOTLB if we are hot-plugged. This allows us to bypass
the need to supply 'iommu=soft' on the Linux command line (mostly).
With this patch, if a user forgot 'iommu=soft' on the command line,
and hotplug a PCI device they will get:
pcifront pci-0: Installing PCI frontend
Warning: only able to allocate 4 MB for software IO TLB
software IO TLB [mem 0x2a000000-0x2a3fffff] (4MB) mapped at [ffff88002a000000-ffff88002a3fffff]
pcifront pci-0: Creating PCI Frontend Bus 0000:00
pcifront pci-0: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
pci 0000:00:00.0: [8086:10d3] type 00 class 0x020000
pci 0000:00:00.0: reg 10: [mem 0xfe5c0000-0xfe5dffff]
pci 0000:00:00.0: reg 14: [mem 0xfe500000-0xfe57ffff]
pci 0000:00:00.0: reg 18: [io 0xe000-0xe01f]
pci 0000:00:00.0: reg 1c: [mem 0xfe5e0000-0xfe5e3fff]
pcifront pci-0: claiming resource 0000:00:00.0/0
pcifront pci-0: claiming resource 0000:00:00.0/1
pcifront pci-0: claiming resource 0000:00:00.0/2
pcifront pci-0: claiming resource 0000:00:00.0/3
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:00:00.0: Disabling ASPM L0s L1
e1000e 0000:00:00.0: enabling device (0000 -> 0002)
e1000e 0000:00:00.0: Xen PCI mapped GSI16 to IRQ34
e1000e 0000:00:00.0: (unregistered net_device): Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e 0000:00:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1b:21🆎c6:13
e1000e 0000:00:00.0: eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:00:00.0: eth0: MAC: 3, PHY: 8, PBA No: E46981-005
The "Warning only" will go away if one supplies 'iommu=soft' instead
as we have a higher chance of being able to allocate large swaths of
memory.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
* pci/trivial:
PCI: Drop duplicate const in DECLARE_PCI_FIXUP_SECTION
PCI: Drop bogus default from ARCH_SUPPORTS_MSI
PCI: cpqphp: Remove unreachable path
PCI: Remove bus number resource debug messages
PCI/AER: Print completion message at KERN_INFO to match starting message
PCI: Fix drivers/pci/pci.c kernel-doc warnings
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
Following code has a race window between pci_find_bus() and pci_get_slot()
if PCI hotplug operation happens between them which removes the pci_bus.
So use PCI hotplug safe interface pci_get_domain_bus_and_slot() instead,
which also reduces code complexity.
struct pci_bus *pci_bus = pci_find_bus(domain, busno);
struct pci_dev *pci_dev = pci_get_slot(pci_bus, devfn);
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Following code has a race window between pci_find_bus() and pci_get_slot()
if PCI hotplug operation happens between them which removes the pci_bus.
So use PCI hotplug safe interface pci_get_domain_bus_and_slot() instead,
which also reduces code complexity.
struct pci_bus *pci_bus = pci_find_bus(domain, busno);
struct pci_dev *pci_dev = pci_get_slot(pci_bus, devfn);
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Following code has a race window between pci_find_bus() and pci_get_slot()
if PCI hotplug operation happens between them which removes the pci_bus.
So use PCI hotplug safe interface pci_get_domain_bus_and_slot() instead,
which also reduces code complexity.
struct pci_bus *pci_bus = pci_find_bus(domain, busno);
struct pci_dev *pci_dev = pci_get_slot(pci_bus, devfn);
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
* 'x86/platform' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (9690 commits)
x86: Document x86_init.paging.pagetable_init()
x86: xen: Cleanup and remove x86_init.paging.pagetable_setup_done()
x86: Move paging_init() call to x86_init.paging.pagetable_init()
x86: Rename pagetable_setup_start() to pagetable_init()
x86: Remove base argument from x86_init.paging.pagetable_setup_start
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
...
The original idea comes from Ram Pai. This patch puts the chunk of
code for calculating the minimal alignment of memory window into a
separate inline function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch changes pbus_size_io() and pbus_size_mem() to do window (I/O,
memory and prefetchable memory) reassignment based on the minimal
alignments for the P2P bridge, which was retrieved by window_alignment().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch implements a weak function to return the default I/O or memory
window alignment for a P2P bridge. By default, I/O windows are aligned to
4KiB or 1KiB and memory windows are aligned to 4MiB. Some platforms, e.g.,
powernv, have special alignment requirements and can override
pcibios_window_alignment().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Options without prompts and without dependencies don't usefully have a
default value - they're intended to be selected from other options
only.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
register & 0x0B == 0x04 is never true, the code will always take the
(identical) 0x00 path anyway. Remove the dead code paths.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44151
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In function pci_get_subsys() there is a check:
/*
* pci_find_subsys() can be called on the ide_setup() path,
* super-early in boot. But the down_read() will enable local
* interrupts, which can cause some machines to crash. So here we
* detect and flag that situation and bail out early.
*/
if (unlikely(no_pci_devices()))
return NULL;
But there is no ide_setup() now, and no down_read() either, which
makes the check obsolete. So remove it.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the driver ignored resume unless the pciehp_force module_param
was specified. On some laptops that means that interrupts are not
delivered after S3, so card removals and insertions are not handled.
This patch makes the driver handle resume regardless of pciehp_force.
[bhelgaas: changelog]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Since pci_error_handlers is just a function table make it const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
On some platforms, root port has neither MSI/MSI-X nor INTx interrupt
generated in RC mode. In this case, we have to use other interrupt, e.g.,
system shared interrupt, for port service IRQ to have AER, Hot-plug, etc.,
services work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 982245f017 ("remove
CONFIG_PCI_NAMES") removed pci's usage of classlist.h, devlist.h, and
gen-devlist. Remove pci's .gitignore file, because now none of its
entries are used.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The completion message in do_recovery() is currently KERN_DEBUG,
while the starting message in aer_print_port_info() is KERN_INFO.
This changes the completion message to KERN_INFO to match the
starting message.
[bhelgaas: changelog, use dev_info() instead of dev_printk(KERN_INFO)]
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The fakephp driver was scheduled for removal in 2011.
Fakephp presented /sys/bus/pci/slots/.../power files for every PCI
function. Writing "0" to one of these files logically removed the device
from the system. The PCI core now provides the same functionality with
/sys/bus/pci/devices/.../remove.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This fixes a kernel warning https://lkml.org/lkml/2012/7/31/682
pci_get_subsys() may get called in late system reboot stage, using
a sleepable kmalloc() sounds fragile and will cause a kernel warning
with my recent commmit 55c844a "x86/reboot: Fix a warning message
triggered by stop_other_cpus()" which disable local interrupt in
late system shutdown/reboot phase. Using a local parameter instead
will fix it and make it eligible for calling from atomic context.
Do the same change for the pci_get_class() as suggested by Bjorn Helgaas.
Initializing the on-stack struct pci_device_id suggested by Fengguang Wu
and Jiri Slaby. Section 6.7.8 of the C99 standard guarantees that when we
initialize some of the struct members, the rest of the struct is implicitly
initialized the same as objects with static storage duration, i.e., to zero
in this case.
[bhelgaas: changelog, incorporate Fengguang/Jiri initialization fix]
Bisected-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fengguang Wu <fengguang.wu@intel.com>
* pci/bjorn-cleanup-remove:
PCI: Remove unused pci_dev_b()
sgi-agp: Use list_for_each_entry() for bus->devices traversal
parisc/PCI: Use list_for_each_entry() for bus->devices traversal
parisc/PCI: Enable PERR/SERR on all devices
frv/PCI: Use list_for_each_entry() for bus->devices traversal
PCI: Leave normal LIST_POISON in deleted list entries
PCI: Rename local variables to conventional names
PCI: Remove unused, commented-out, code
PCI: Stop and remove devices in one pass
PCI: Fold stop and remove helpers into their callers
PCI: Use list_for_each_entry() for bus->devices traversal
PCI: Remove pci_stop_and_remove_behind_bridge()
PCI: Don't export stop_bus_device and remove_bus_device interfaces
pcmcia: Use common pci_stop_and_remove_bus_device()
PCI: acpiphp: Use common pci_stop_and_remove_bus_device()
PCI: acpiphp: Stop disabling bridges on remove
If we try to print to the console device while its decoding is disabled,
the system will hang.
Reported-and-tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Olof Johansson <olof@lixom.net>
Before initiating an FLR, we should wait for completion of any outstanding
non-posted requests. See PCIe spec r3.0, sec 6.6.2.
This makes reset_intel_82599_sfp_virtfn() very similar to the generic
pcie_flr(). The only difference is that the 82599 doesn't report FLR
support in the VF Device Capability register.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI Express Capability (PCIe spec r3.0, sec 7.8) comes in two
versions, v1 and v2. In v1 Capability structures (PCIe spec r1.0 and
r1.1), some fields are optional, so the structure size depends on the
device type.
This patch adds functions to access this capability so drivers don't
have to be aware of the differences between v1 and v2. Note that these
new functions apply only to the "PCI Express Capability," not to any of
the other "PCI Express Extended Capabilities" (AER, VC, ACS, MFVC, etc.)
Function pcie_capability_read_word/dword() reads the PCIe Capabilities
register and returns the value in the reference parameter "val". If
the PCIe Capabilities register is not implemented on the PCIe device,
"val" is set to 0.
Function pcie_capability_write_word/dword() writes the value to the
specified PCIe Capability register.
Function pcie_capability_clear_and_set_word/dword() sets and/or clears bits
of a PCIe Capability register.
[bhelgaas: changelog, drop "pci_" prefixes, don't export
pcie_capability_reg_implemented()]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With introduction of pci_pcie_type(), pci_dev->pcie_type field becomes
redundant, so remove it.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce an inline function pci_pcie_type(dev) to extract PCIe
device type from pci_dev->pcie_flags_reg field, and prepare for
removing pci_dev->pcie_type.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some extended capabilities, e.g., the vendor-specific capability, can
occur several times. The existing pci_find_ext_capability() only finds
the first occurrence. This adds pci_find_next_ext_capability(), which
can iterate through all of them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix kernel-doc warnings in drivers/pci/pci.c:
Warning(drivers/pci/pci.c:1550): No description found for parameter 'pci_dev'
Warning(drivers/pci/pci.c:1550): Excess function parameter 'dev' description in 'pci_wakeup'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
list_del() already sets next/prev to LIST_POISON1/LIST_POISON2, so we
don't need to do anything special here to prevent further list accesses.
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
"bus" is the conventional name for a "struct pci_bus *" variable.
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
This removes unused code that was already commented out.
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Previously, when we removed a PCI device, we made two passes over the
hierarchy rooted at the device. In the first pass, we stopped all
the devices, and in the second, we removed them.
This patch combines the two passes into one so that we remove a device as
soon as it and all its children have been stopped.
Note that we previously stopped devices in reverse order and removed them
in forward order. Now we stop and remove them in reverse order.
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
pci_stop_bus_devices() is only two lines of code and is only called by
pci_stop_bus_device(), so I think it's easier to read if we just fold it
into the caller. Similarly for __pci_remove_behind_bridge().
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Replace list_for_each() + pci_dev_b() with the simpler
list_for_each_entry().
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The PCMCIA CardBus driver was the only user of
pci_stop_and_remove_behind_bridge(), and it now uses
pci_stop_and_remove_bus_device() instead, so remove this interface.
This removes exported symbol pci_stop_and_remove_behind_bridge.
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The acpiphp hotplug driver was the only user of pci_stop_bus_device() and
__pci_remove_bus_device(), and it now uses pci_stop_and_remove_bus_device()
instead, so stop exposing these interfaces.
This removes these exported symbols:
__pci_remove_bus_device
pci_stop_bus_device
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Use pci_stop_and_remove_bus_device() like most other hotplug drivers
rather than stopping and removing separately.
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
This patch fixes the following bug:
http://marc.info/?l=linux-pci&m=134338059022620&w=2
Where lspci does not work properly if a device and the corresponding
parent bridge (such as PCIe port) is suspended. This is because the
device configuration space registers will be not accessible if the
corresponding parent bridge is suspended or the device is put into
D3cold state.
To solve the issue, the bridge/PCIe port connected to the device is
put into active state before read/write configuration space registers.
If the device is in D3cold state, it will be put into active state
too.
To avoid resume/suspend PCIe port for each configuration register
read/write, a small delay is added before the PCIe port to go
suspended.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch fixes the following bug:
http://marc.info/?l=linux-pci&m=134329923124234&w=2
The root cause of the bug is as follow.
If a device is not bound with the corresponding driver, the device
runtime PM will be disabled and the device will be put into suspended
state. So that, the bridge/PCIe port connected to it may be put into
suspended and low power state. When do probing for the device later,
because the bridge/PCIe port connected to it is in low power state,
the IO access to device may fail.
To solve the issue, the bridge/PCIe port connected to the device is
put into active state before probing.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch fixes the following bug:
http://marc.info/?l=linux-usb&m=134318961120825&w=2
Originally, device lower power states include D1, D2, D3. After that,
D3 is further divided into D3hot and D3cold. To support both scenario
safely, original D3 is mapped to D3cold.
When adding D3cold support, because worry about some device may have
broken D3cold support, D3cold is disabled by default. This disable D3
on original platform too. But some original platform may only have
working D3, but no working D1, D2. The root cause of the above bug is
it too.
To deal with this, this patch enables D3/D3cold by default for most
devices. This restores the original behavior. For some devices that
suspected to have broken D3cold support, such as PCIe port, D3cold is
disabled by default.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
There is no need for those functions/variables to be visible. Make them
static and also fix the compile warnings of this sort:
drivers/xen/<some file>.c: warning: symbol '<blah>' was not declared. Should it be static?
Some of them just require including the header file that
declares the functions.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since PCI Express Capabilities Register is read only, cache its value
into struct pci_dev to avoid repeatedly calling pci_read_config_*().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
acpiphp_disable_slot() turns off power to the slot immediately after
calling disable_device(), so there's no point in disabling any bridges
below the slot: we're about to turn them off anyway.
Tested-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Commit dbf0e4c (PCI: EHCI: fix crash during suspend on ASUS
computers) added a workaround for an ASUS suspend issue related to
USB EHCI and a bug in a number of ASUS BIOSes that attempt to shut
down the EHCI controller during system suspend if its PCI command
register doesn't contain 0 at that time.
It turns out that the same workaround is necessary in the analogous
hibernation code path, so add it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=45811
Reported-and-tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
If a PCI device is put into D3_cold by acpi_bus_set_power(),
the message printed by acpi_pci_set_power_state() says that its
power state has been changed to D4, which doesn't make sense.
In turn, if the device is put into D3_hot, the message simply
says "D3" without specifying the variant of the D3 state.
Fix this by using the pci_power_name() macro for printing the state
name instead of building it from the numeric value corresponding to
the given state directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
Pull arch/tile updates from Chris Metcalf:
"These changes provide support for PCIe root complex and USB host mode
for tilegx's on-chip I/Os.
In addition, this pull provides the required underpinning for the
on-chip networking support that was pulled into 3.5. The changes have
all been through LKML (with several rounds for PCIe RC) and on
linux-next."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: updates to pci root complex from community feedback
bounce: allow use of bounce pool via config option
usb: add host support for the tilegx architecture
arch/tile: provide kernel support for the tilegx USB shim
tile pci: enable IOMMU to support DMA for legacy devices
arch/tile: enable ZONE_DMA for tilegx
tilegx pci: support I/O to arbitrarily-cached pages
tile: remove unused header
arch/tile: tilegx PCI root complex support
arch/tile: provide kernel support for the tilegx TRIO shim
arch/tile: break out the "csum a long" function to <asm/checksum.h>
arch/tile: provide kernel support for the tilegx mPIPE shim
arch/tile: common DMA code for the GXIO IORPC subsystem
arch/tile: support MMIO-based readb/writeb etc.
arch/tile: introduce GXIO IORPC framework for tilegx
This change implements PCIe root complex support for tilegx using
the kernel support layer for accessing the TRIO hardware shim.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> [changes in 07487f3]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Typically, the return value desired for the failure of a function with an
integer return value is a negative integer. In these cases, the return
value is sometimes a negative integer and sometimes 0, due to a subsequent
initialization of the return variable within the loop.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
//<smpl>
@r exists@
identifier ret;
position p;
constant C;
expression e1,e3,e4;
statement S;
@@
ret = -C
... when != ret = e3
when any
if@p (...) S
... when any
if (\(ret != 0\|ret < 0\|ret > 0\) || ...) { ... return ...; }
... when != ret = e3
when any
*if@p (...)
{
... when != ret = e4
return ret;
}
//</smpl>
[bhelgaas: squashed into one patch]
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My "PCI: Integrate 'pci_fixup_final' quirks into hot-plug paths" patch
introduced an undefined reference to 'pci_fixup_final_inited' when
CONFIG_PCI_QUIRKS is not enabled (on x86_64):
drivers/built-in.o: In function `pci_bus_add_device':
(.text+0x4f62): undefined reference to `pci_fixup_final_inited'
This patch removes the external reference ending up with a result closer
to what we ultimately want when the boot path issues described in the
original patch are resolved.
References:
https://lkml.org/lkml/2012/7/9/542 Original, offending, patch
https://lkml.org/lkml/2012/7/12/338 Randy's catch
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
The ColdFire M54xx family of CPU cores (supported by the m68k arch code)
have PCI bus hardware. We want to be able to use this and will need the
setup-bus.c and setup-irq.c helper functions. So when CONFIG_M68K is
enabled add them to the objs build list.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reorder functions so __pci_assign_resource(), _pci_assign_resource(),
and pci_assign_resource() are closer together. No code change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
_pci_assign_resource() took an int "size" argument, which meant that
sizes larger than 4GB were truncated. Change type to resource_size_t.
[bhelgaas: changelog]
Signed-off-by: Nikhil P Rao <nikhil.rao@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Should not have two, just remove debug, and use module_param_named
instead.
Also change acpiphp_debug to bool.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Quite a few ASUS computers experience a nasty problem, related to the
EHCI controllers, when going into system suspend. It was observed
that the problem didn't occur if the controllers were not put into the
D3 power state before starting the suspend, and commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers) was created to do this.
It turned out this approach messed up other computers that didn't have
the problem -- it prevented USB wakeup from working. Consequently
commit c2fb8a3fa2 (USB: add
NO_D3_DURING_SLEEP flag and revert 151b612847) was merged; it
reverted the earlier commit and added a whitelist of known good board
names.
Now we know the actual cause of the problem. Thanks to AceLan Kao for
tracking it down.
According to him, an engineer at ASUS explained that some of their
BIOSes contain a bug that was added in an attempt to work around a
problem in early versions of Windows. When the computer goes into S3
suspend, the BIOS tries to verify that the EHCI controllers were first
quiesced by the OS. Nothing's wrong with this, but the BIOS does it
by checking that the PCI COMMAND registers contain 0 without checking
the controllers' power state. If the register isn't 0, the BIOS
assumes the controller needs to be quiesced and tries to do so. This
involves making various MMIO accesses to the controller, which don't
work very well if the controller is already in D3. The end result is
a system hang or memory corruption.
Since the value in the PCI COMMAND register doesn't matter once the
controller has been suspended, and since the value will be restored
anyway when the controller is resumed, we can work around the BIOS bug
simply by setting the register to 0 during system suspend. This patch
(as1590) does so and also reverts the second commit mentioned above,
which is now unnecessary.
In theory we could do this for every PCI device. However to avoid
introducing new problems, the patch restricts itself to EHCI host
controllers.
Finally the affected systems can suspend with USB wakeup working
properly.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728
Based-on-patch-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Javier Marcet <jmarcet@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: stable <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pci/bjorn-p2p-bridge-windows:
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: allow P2P bridge windows starting at PCI bus address zero
Conflicts:
drivers/pci/probe.c
include/linux/pci.h
* pci/bjorn-disable-decode:
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
* pci/myron-final-fixups-v2:
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
Final fixups are currently applied only at boot-time by
pci_apply_final_quirks(), which is an fs_initcall(). Hot-added devices
don't get these fixups, so they may not be completely initialized.
This patch makes us run final fixups for hot-added devices in
pci_bus_add_device() just before the new device becomes eligible for driver
binding.
This patch keeps the fs_initcall() for devices present at boot because we
do resource assignment between pci_bus_add_device and the fs_initcall(),
and we don't want to break any fixups that depend on that assignment. This
is a design issue that may be addressed in the future -- any resource
assignment should be done *before* device_add().
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Final fixups are executed during device enumeration. If we support
hotplug, this may be after boot, so final fixups cannot be __init.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some bridges support I/O windows with 1K alignment, not just the 4K
alignment defined by the PCI spec. For example, see the IOBL_ADR register
and the EN1K bit in the CNF register in the Intel 82870P2 (P64H2).
This patch adds support for sizing the window in 1K increments based
on the requirements of downstream devices.
[bhelgaas: changelog, comment]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
9d265124d0 and 15a260d53f added quirks for P2P bridges that support
I/O windows that start/end at 1K boundaries, not just the 4K boundaries
defined by the PCI spec. For details, see the IOBL_ADR register and the
EN1K bit in the CNF register in the Intel 82870P2 (P64H2).
These quirks complicate the code that reads P2P bridge windows
(pci_read_bridge_io() and pci_cfg_fake_ranges()) because the bridge
I/O resource is updated in the HEADER quirk, in pci_read_bridge_io(),
in pci_setup_bridge(), and again in the FINAL quirk. This is confusing
and makes it impossible to reassign the bridge windows after FINAL
quirks are run.
This patch adds support for 1K windows in the generic paths, so the
HEADER quirk only has to enable this support. The FINAL quirk, which
used to undo damage done by pci_setup_bridge(), is no longer needed.
This removes "if (!res->start) res->start = ..." from pci_read_bridge_io();
that was part of 9d265124d0 to avoid overwriting the resource filled in
by the quirk. Since pci_read_bridge_io() itself now knows about
granularity, the quirk no longer updates the resource and this test is no
longer needed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When we update 64-bit BARs, we have to perform two config writes. Between
the writes, the half-written BAR value could match a MEM access intended
for another device. This could result in corruption of this device (for
writes) or an unexpected response machine check (for reads).
To prevent this, disable MEM decoding while updating such BARs. This uses
the same safety test as 253d2e5498, which disables both MEM and IO while
sizing BARs, namely, we don't disable decoding for host bridge devices.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After 253d2e5498, we disable MEM and IO decoding for most devices while we
size 32-bit BARs. However, we restore the original COMMAND register before
we size the upper 32 bits of 64-bit BARs, so we can still cause a conflict.
This patch waits to restore the original COMMAND register until we're
completely finished sizing the BAR.
Reference: https://lkml.org/lkml/2007/8/25/154
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The enable/suspend/resume_early/resume fixups can be called at any time, so
they can't be __init or __devinit.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
__nv_msi_ht_cap_quirk() acquires a temporary reference via
'pci_get_bus_and_slot()' that is never released.
This patch releases the temporary reference.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch restructures pci_do_fixups()'s quirk invocations in the style
of initcall_debug_start() and initcall_debug_report(), so we have only
one call site for the quirk.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
cd81e1ea1a added checks that prevent us from using P2P bridge windows
that start at PCI bus address zero. The reason was to "prevent us from
overwriting resources that are unassigned."
But generic code should allow address zero in both BARs and bridge
windows, so I think that commit was a mistake.
Windows at bus address zero are legal and likely to exist on machines with
an offset between bus addresses and CPU addresses. For example, in the
following hypothetical scenario, the bridge at 00:01.0 has a window at bus
address zero and the device at 01:00.0 has a BAR at bus address zero, and
I think both are perfectly valid:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x100000000-0x1ffffffff] (bus address [0x00000000-0xffffffff])
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [mem 0x100000000-0x100ffffff]
pci 0000:01:00.0: reg 10: [mem 0x100000000-0x100ffffff]
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/myron-pcibios_setup:
xtensa/PCI: factor out pcibios_setup()
x86/PCI: adjust section annotations for pcibios_setup()
unicore32/PCI: adjust section annotations for pcibios_setup()
tile/PCI: factor out pcibios_setup()
sparc/PCI: factor out pcibios_setup()
sh/PCI: adjust section annotations for pcibios_setup()
sh/PCI: factor out pcibios_setup()
powerpc/PCI: factor out pcibios_setup()
parisc/PCI: factor out pcibios_setup()
MIPS/PCI: adjust section annotations for pcibios_setup()
MIPS/PCI: factor out pcibios_setup()
microblaze/PCI: factor out pcibios_setup()
ia64/PCI: factor out pcibios_setup()
cris/PCI: factor out pcibios_setup()
alpha/PCI: factor out pcibios_setup()
PCI: pull pcibios_setup() up into core
Commit cc2893b6 (PCI: Ensure we re-enable devices on resume)
addressed the problem with USB not being powered after resume on
recent Lenovo machines, but it did that in a suboptimal way.
Namely, it should have changed the relevant code paths only,
which are pci_pm_resume_noirq() and pci_pm_restore_noirq() supposed
to restore the device's power and standard configuration registers
after system resume from suspend or hibernation. Instead, however,
it modified pci_set_power_state() which is executed in several
other situations too. That resulted in some undesirable effects,
like attempting to change a device's power state in the same way
multiple times in a row (up to as many as 4 times in a row in the
snd_hda_intel driver).
Fix the bug addressed by commit cc2893b6 in an alternative way,
by forcibly powering up all devices in pci_pm_default_resume_early(),
which is called by pci_pm_resume_noirq() and pci_pm_restore_noirq()
to restore the device's power and standard configuration registers,
and modifying pci_pm_runtime_resume() to avoid the forcible power-up
if not necessary. Then, revert the changes made by commit cc2893b6
to make the confusion introduced by it go away.
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, all of the architectures implement their own pcibios_setup()
routine. Most of the implementations do nothing so this patch introduces
a generic (__weak) routine in the core that can be used by all
architectures as a default. If necessary, it can be overridden by
architecture-specific code.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* topic/huang-d3cold-v7:
PCI/PM: add PCIe runtime D3cold support
PCI: do not call pci_set_power_state with PCI_D3cold
PCI/PM: add runtime PM support to PCIe port
ACPI/PM: specify lowest allowed state for device sleep state
This patch adds runtime D3cold support and corresponding ACPI platform
support. This patch only enables runtime D3cold support; it does not
enable D3cold support during system suspend/hibernate.
D3cold is the deepest power saving state for a PCIe device, where its main
power is removed. While it is in D3cold, you can't access the device at
all, not even its configuration space (which is still accessible in D3hot).
Therefore the PCI PM registers can not be used to transition into/out of
the D3cold state; that must be done by platform logic such as ACPI _PR3.
To support wakeup from D3cold, a system may provide auxiliary power, which
allows a device to request wakeup using a Beacon or the sideband WAKE#
signal. WAKE# is usually connected to platform logic such as ACPI GPE.
This is quite different from other power saving states, where devices
request wakeup via a PME message on the PCIe link.
Some devices, such as those in plug-in slots, have no direct platform
logic. For example, there is usually no ACPI _PR3 for them. D3cold
support for these devices can be done via the PCIe Downstream Port leading
to the device. When the PCIe port is powered on/off, the device is powered
on/off too. Wakeup events from the device will be notified to the
corresponding PCIe port.
For more information about PCIe D3cold and corresponding ACPI support,
please refer to:
- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0
[bhelgaas: changelog]
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch adds runtime PM support to PCIe port. This is needed by
PCIe D3cold support, where PCIe device without ACPI node may be
powered on/off by PCIe port.
Because runtime suspend is broken for some chipsets, a black list is
used to disable runtime PM support for these chipsets.
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Lower device sleep state can save more power, but has more exit
latency too. Sometimes, to satisfy some power QoS and other
requirement, we need to constrain the lowest device sleep state.
In this patch, a parameter to specify lowest allowed state for
acpi_pm_device_sleep_state is added. So that the caller can enforce
the constraint via the parameter.
This is needed by PCIe D3cold support, where the lowest power state
allowed may be D3_HOT instead of default D3_COLD.
CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* topic/jiang-mmconfig-v10:
ACPI: mark acpi_sfi_table_parse() as __init
x86/PCI: use pr_level() to replace printk(KERN_LEVEL)
x86/PCI: refine __pci_mmcfg_init() for better code readability
x86/PCI: get rid of redundant log messages
x86/PCI: simplify pci_mmcfg_late_insert_resources()
x86/PCI: update MMCONFIG information when hot-plugging PCI host bridges
PCI/ACPI: provide MMCONFIG address for PCI host bridges
x86/PCI: add pci_mmconfig_insert()/delete() for PCI root bridge hotplug
x86/PCI: prepare pci_mmcfg_check_reserved() to be called at runtime
x86/PCI: introduce pci_mmcfg_arch_map()/pci_mmcfg_arch_unmap()
x86/PCI: use RCU list to protect mmconfig list
x86/PCI: split out pci_mmconfig_alloc() for code reuse
x86/PCI: split out pci_mmcfg_check_reserved() for code reuse
This patch provide MMCONFIG address for PCI host bridges, which will
be used to support host bridge hotplug. It gets MMCONFIG address
by evaluating _CBA method if available.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For a valid pci_dev, dev->bus != NULL always, so remove this
unnecessary test.
Found by Coverity (CID 101680).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check whether we evaluated _ADR successfully. Previously we ignored
failure, so we would have used garbage data from the stack as the device
and function number.
We return AE_OK so that we ignore only this slot and continue looking
for other slots.
Found by Coverity (CID 113981).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"slots_not_empty" is initialized to zero and can't be set again before
reaching this point, so this return statement is dead. Remove it.
Found by Coverity (CID 114324).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On P2P bridges with 32-bit I/O decoding, we incorrectly sign-extended
windows starting at 0x80000000 or above. In "base |= (io_base_hi << 16)",
"io_base_hi" is promoted to a signed int before being extended to an
unsigned long.
This would cause a window starting at I/O address 0x80000000 to be
treated as though it started at 0xffffffff80008000 instead, which
should cause "no compatible bridge window" errors when we enumerate
devices using that I/O space.
The mmio and mmio_pref casts are not strictly necessary, but without
them, correctness depends on the types of the PCI_MEMORY_RANGE_MASK and
PCI_PREF_RANGE_MASK constants, which are not obvious from reading the
local code.
Found by Coverity (CID 138747 and CID 138748).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_enable_obff() and pci_enable_ltr() incorrectly check "dev->bus" instead
of "dev->bus->self" to determine whether the upstream device is a P2P
bridge or a host bridge. For devices on the root bus, the upstream device
is a host bridge, "dev->bus != NULL" and "dev->bus->self == NULL", and we
panic with a null pointer dereference.
These functions should previously have panicked when called on devices
supporting OBFF or LTR, so they should be regarded as untested.
Found by Coverity (CID 143038 and CID 143039).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Warning(drivers/pci/setup-bus.c:277): No description found for parameter 'fail_head'
Warning(drivers/pci/setup-bus.c:277): Excess function parameter 'failed_list' description in 'assign_requested_resources_sorted'
Signed-off-by: Wanpeng Li <liwp.linux@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* topic/sebastian-devinit-fixups:
scripts/modpost: check for bad references in .pci.fixups area
sh/PCI: move fixup hooks from __init to __devinit
powerpc/PCI: move fixup hooks from __init to __devinit
frv/PCI: move fixup hooks from __init to __devinit
arm/PCI: move fixup hooks from __init to __devinit
alpha/PCI: move fixup hooks from __init to __devinit
PCI: move fixup hooks from __init to __devinit
x86/PCI: move fixup hooks from __init to __devinit
Passes pci_intx_mask_supported test but continues to send interrupts
as discovered through VFIO-based device assignment.
http://www.spinics.net/lists/kvm/msg73738.html
[bhelgaas: use HEADER, not FINAL, which is currently broken for hotplug]
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
According to
http://thread.gmane.org/gmane.comp.emulators.kvm.devel/91388
the T310 does not properly support INTx masking as it fails to keep the
PCI_STATUS_INTERRUPT bit updated once the interrupt is masked. Mark this
adapter as broken so that pci_intx_mask_supported won't report it as
compatible.
[bhelgaas: use HEADER, not FINAL, which is currently broken for hotplug]
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_intx_mask_supported() assumes INTx masking is supported if the
PCI_COMMAND_INTX_DISABLE bit is writable. But when that bit is set,
some devices don't actually mask INTx or update PCI_STATUS_INTERRUPT
as we expect.
This patch adds a way for quirks to identify these broken devices.
[bhelgaas: split out from Chelsio quirk addition]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When we add a device with acpiphp, we enumerate all functions in the
slot with pci_scan_slot(), regardless of whether they have associated
ACPI methods such as _EJ0.
When removing the device, we previously removed only the functions
with those ACPI methods. This patch makes the remove symmetric with the
add: we remove all functions in the slot, whether they have associated
ACPI methods or not.
With qemu-kvm and SeaBIOS, we can build a multi-function device where
only function 0 has _EJ0 and _ADR (see bugzilla below). Removing and
re-adding that slot (including all functions of the device) works correctly
with Windows guests. This patch makes it also work in Linux guests.
[bhelgaas: restructure loop iteration, pull out of slot->funcs loop]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=43219
Signed-off-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, we acquired two references to function 0, but only released
one.
[bhelgaas: split this out from "remove all functions" fix]
Signed-off-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All callers of pci_do_scan_bus() are gone, so remove it.
Note that pci_do_scan_bus() was exported, so out-of-tree modules could
depend on it.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new generic pci_hp_add_bridge() interface.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new generic pci_hp_add_bridge() interface.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new generic pci_hp_add_bridge() interface.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new generic pci_hp_add_bridge() interface.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new generic pci_hp_add_bridge() interface.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new generic pci_hp_add_bridge() interface.
[bhelgaas: split "add generic pci_hp_add_bridge()" into a separate patch]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This creates a generic pci_hp_add_bridge() that can be used by several
hotplug drivers.
[bhelgaas: split out from pciehp patch]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now we can insert busn_res now, after all root bus's get inserted.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to put into the resources list for legacy system.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some callers do not supply the bus number aperture, usually because they do
not know the end. In this case, we assume the aperture extends from the
root bus number to bus 255, scan the bus, and shrink the bus number
resource so it ends at the largest bus number we found.
This is obviously not correct because the actual end of the aperture may
well be larger than the largest bus number we found. But I guess it's all
we have for now.
Also print out one info about that, so we could find out which path
does not have busn_res in resources list.
[bhelgaas: changelog, _safe iterator unnecessary, use %pR format for bus]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Will use them insert/update busn res in pci_bus struct.
[bhelgaas: print conflicting entry if insertion fails]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds get_pci_domain_busn_res(), which returns the root of the
bus number resource tree for a domain, creating it if necessary.
We will later populate the tree with the bus numbers used by host
bridges and P2P bridges in the domain.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VFIO PCI support will make use of these for user-initiated
PCI config accesses.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In a PCI environment, transactions aren't always required to reach
the root bus before being re-routed. Intermediate switches between
an endpoint and the root bus can redirect DMA back downstream before
things like IOMMUs have a chance to intervene. Legacy PCI is always
susceptible to this as it operates on a shared bus. PCIe added a
new capability to describe and control this behavior, Access Control
Services, or ACS.
The utility function pci_acs_enabled() allows us to test the ACS
capabilities of an individual devices against a set of flags while
pci_acs_path_enabled() tests a complete path from a given downstream
device up to the specified upstream device. We also include the
ability to add device specific tests as it's likely we'll see
devices that do not implement ACS, but want to indicate support
for various capabilities in this space.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The fixups are executed once the pci-device is found which is during
boot process so __init seems fine as long as the platform does not
support hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Unlike PCI Express v1's Capabilities Structure, v2's requires the entire
structure to be implemented. In v2 structures, register fields that
are not implemented are present but hardwired to 0x0. These may
include: Link Capabilities, Status, and Control; Slot Capabilities,
Status, and Control; Root Capabilities, Status, and Control; and all of
the '2' (Device, Link, and Slot) Capabilities, Status, and Control
registers.
This patch removes the redundant capability checks corresponding to the
Link 2's and Slot 2's, Capabilities, Status, and Control registers as they
will be present if Device Capabilities 2's registers are (which explains
why the macros for each of the three are identical).
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch resolves potential issues when accessing PCI Express
Capability structures. The makeup of the capability varies
substantially between v1 and v2:
Version 1 of the PCI Express Capability (defined by PCI Express
1.0 and 1.1 base) neither requires the endpoint to implement the
entire PCIe capability structure nor specifies default values of
registers that are not implemented by the device.
Version 2 of the PCI Express Capability (defined by PCIe 1.1
Capability Structure Expansion ECN, PCIe 2.0, 2.1, and 3.0) added
additional registers to the structure and requires all registers
to be either implemented or hardwired to 0.
Due to the differences in the capability structures, code dealing with
capability features must be careful not to access the additional
registers introduced with v2 unless the device is specifically known to
be a v2 capable device. Otherwise, attempts to access non-existant
registers will occur. This is a subtle issue that is hard to track down
when it occurs (and it has - see commit 864d296cf9).
To try and help mitigate such occurrences, this patch introduces
pci_pcie_cap2() which is similar to pci_pcie_cap() but also checks
that the PCIe capability version is >= 2. pci_pcie_cap2() should be
used for qualifying PCIe capability features introduced after v1.
Suggested by Don Dutile.
Acked-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are a number of redundant pci_is_pcie() checks in various PCI
Express capabilities related routines like the following:
if (!pci_is_pcie(dev))
return false;
pos = pci_pcie_cap(dev);
if (!pos)
return false;
The current pci_is_pcie() implementation is merely:
static inline bool pci_is_pcie(struct pci_dev *dev)
{
return !!pci_pcie_cap(dev);
}
so we can just drop the pci_is_pcie() test in such cases.
Acked-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI Express Latency Tolerance Reporting (LTR) feature's
pci_ltr_supported() routine is currently only used within
drivers/pci/pci.c so make it static.
Acked-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DMA transactions are tagged with the source ID of the device making
the request. Occasionally hardware screws this up and uses the
source ID of a different device (often the wrong function number of
a multifunction device). A specific Ricoh multifunction device is
a prime example of this problem and included in this patch.
Given a pci_dev, this function returns the pci_dev to use as the
source ID for DMA. When hardware works correctly, this returns
the input device. For the components of the Ricoh multifunction
device, it returns the pci_dev for function 0.
This will be used by IOMMU drivers for determining the boundaries
of IOMMU groups as multiple devices using the same source ID must
be contained within the same group. This can also be used by
existing streaming DMA paths for the same purpose.
[bhelgaas: fold in pci_dev_get() for !CONFIG_PCI]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_is_pcie() instead of looking at obsolete is_pcie field in
struct pci_dev.
CC: Huang Ying <ying.huang@intel.com>
CC: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_max_busnr() has been commented out for years (since 54c762fe62), and
this patch removes it completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
Pull main drm updates from Dave Airlie:
"This is the main merge window request for the drm.
It's big, but jam packed will lots of features and of course 0
regressions. (okay maybe there'll be one).
Highlights:
- new KMS drivers for server GPU chipsets: ast, mgag200 and cirrus
(qemu only). These drivers use the generic modesetting drivers.
- initial prime/dma-buf support for i915, nouveau, radeon, udl and
exynos
- switcheroo audio support: so GPUs with HDMI can turn off the sound
driver without crashing stuff.
- There are some patches drifting outside drivers/gpu into x86 and
EFI for better handling of multiple video adapters in Apple Macs,
they've got correct acks except one trivial fixup.
- Core:
edid parser has better DMT and reduced blanking support,
crtc properties,
plane properties,
- Drivers:
exynos: add 2D core accel support, prime support, hdmi features
intel: more Haswell support, initial Valleyview support, more
hdmi infoframe fixes, update MAINTAINERS for Daniel, lots of
cleanups and fixes
radeon: more HDMI audio support, improved GPU lockup recovery
support, remove nested mutexes, less memory copying on PCIE, fix
bus master enable race (kexec), improved fence handling
gma500: cleanups, 1080p support, acpi fixes
nouveau: better nva3 memory reclocking, kepler accel (needs
external firmware rip), async buffer moves on nv84+ hw.
I've some more dma-buf patches that rely on the dma-buf merge for vmap
stuff, and I've a few fixes building up, but I'd decided I'd better
get rid of the main pull sooner rather than later, so the audio guys
are also unblocked."
Fix up trivial conflict due to some duplicated changes in
drivers/gpu/drm/i915/intel_ringbuffer.c
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (605 commits)
drm/nouveau/nvd9: Fix GPIO initialisation sequence.
drm/nouveau: Unregister switcheroo client on exit
drm/nouveau: Check dsm on switcheroo unregister
drm/nouveau: fix a minor annoyance in an output string
drm/nouveau: turn a BUG into a WARN
drm/nv50: decode PGRAPH DATA_ERROR = 0x24
drm/nouveau/disp: fix dithering not being enabled on some eDP macbooks
drm/nvd9/copy: initialise copy engine, seems to work like nvc0
drm/nvc0/ttm: use copy engines for async buffer moves
drm/nva3/ttm: use copy engine for async buffer moves
drm/nv98/ttm: add in a (disabled) crypto engine buffer copy method
drm/nv84/ttm: use crypto engine for async buffer copies
drm/nouveau/ttm: untangle code to support accelerated buffer moves
drm/nouveau/fbcon: use fence for sync, rather than notifier
drm/nv98/crypt: non-stub implementation of the engine hooks
drm/nouveau/fifo: turn all fifo modules into engine modules
drm/nv50/graph: remove ability to do interrupt-driven context switching
drm/nv50: remove manual context unload on context destruction
drm/nv50: remove execution engine context saves on suspend
drm/nv50/fifo: use hardware channel kickoff functionality
...
On MIPS we want to call of_irq_map_pci from inside
arch/mips/include/asm/pci.h:extern int pcibios_map_irq(
const struct pci_dev *dev, u8 slot, u8 pin);
For this to work we need to change several functions to const usage.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-pci@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-mips@linux-mips.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3710/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1cc0c998fd ("ACPI: Fix D3hot v D3cold confusion") introduced a
bug in __acpi_bus_set_power() and changed the behavior of
acpi_pci_set_power_state() in such a way that it generally doesn't work
as expected if PCI_D3hot is passed to it as the second argument.
First off, if ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) is passed to
__acpi_bus_set_power() and the explicit_set flag is set for the D3cold
state, the function will try to execute AML method called "_PS4", which
doesn't exist.
Fix this by adding a check to ensure that the name of the AML method
to execute for transitions to ACPI_STATE_D3_COLD is correct in
__acpi_bus_set_power(). Also make sure that the explicit_set flag
for ACPI_STATE_D3_COLD will be set if _PS3 is present and modify
acpi_power_transition() to avoid accessing power resources for
ACPI_STATE_D3_COLD, because they don't exist.
Second, if PCI_D3hot is passed to acpi_pci_set_power_state() as the
target state, the function will request a transition to
ACPI_STATE_D3_HOT instead of ACPI_STATE_D3. However,
ACPI_STATE_D3_HOT is now only marked as supported if the _PR3 AML
method is defined for the given device, which is rare. This causes
problems to happen on systems where devices were successfully put
into ACPI D3 by pci_set_power_state(PCI_D3hot) which doesn't work
now. In particular, some unused graphics adapters are not turned
off as a result.
To fix this issue restore the old behavior of
acpi_pci_set_power_state(), which is to request a transition to
ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) if either PCI_D3hot or
PCI_D3cold is passed to it as the argument.
This approach is not ideal, because generally power should not
be removed from devices if PCI_D3hot is the target power state,
but since this behavior is relied on, we have no choice but to
restore it at the moment and spend more time on designing a
better solution in the future.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43228
Reported-by: rocko <rockorequin@hotmail.com>
Reported-by: Cristian Rodríguez <crrodriguez@opensuse.org>
Reported-and-tested-by: Peter <lekensteyn@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of these:
drivers/pci/pcie/portdrv_core.c: In function 'pcie_port_device_register':
drivers/pci/pcie/portdrv_core.c:275:16: warning: 'cap_mask' may be used
uninitialized in this function [-Wuninitialized]
drivers/pci/pcie/portdrv_core.c:240:6: note: 'cap_mask' was declared here
In some cases, 'cap_mask' may be not set in pcie_port_platform_notify,
holding a garbage value.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into drm-intel-next
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull an ACPI patch from Len Brown:
"It fixes a D3 issue new in 3.4-rc1."
By Lin Ming via Len Brown:
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPI: Fix D3hot v D3cold confusion
Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.
After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.
ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot) If these resources are all ON,
then the state is D3hot. If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.
This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Disable Bus Master bit on the device in pci_device_shutdown() to ensure PCI
devices do not continue to DMA data after shutdown. This can cause memory
corruption in case of a kexec where the current kernel shuts down and
transfers control to a new kernel while a PCI device continues to DMA to
memory that does not belong to it any more in the new kernel.
I have tested this code on two laptops, two workstations and a 16-socket
server. kexec worked correctly on all of them.
Signed-off-by: Khalid Aziz <khalid.aziz@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For IvyBridge Mobile platform, a system hang may occur if a FLR (Function
Level Reset) is asserted to internal graphics.
This quirk is a workaround for the IVB FLR errata issue. We are
disabling the FLR reset handshake between the PCH and CPU display, then
manually powering down the panel power sequencing and resetting the PCH
display.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Kay, Allen M <allen.m.kay@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Daniel Vetter writes:
A new drm-intel-next pull. Highlights:
- More gmbus patches from Daniel Kurtz, I think gmbus is now ready, all
known issues fixed.
- Fencing cleanup and pipelined fencing removal from Chris.
- rc6 residency interface from Ben, useful for powertop.
- Cleanups and code reorg around the ringbuffer code (Ben&me).
- Use hw semaphores in the pageflip code from Ben.
- More vlv stuff from Jesse, unfortunately his vlv cpu is doa, so less
merged than I've hoped for - we still have the unused function warning :(
- More hsw patches from Eugeni, again, not yet enabled fully.
- intel_pm.c refactoring from Eugeni.
- Ironlake sprite support from Chris.
- And various smaller improvements/fixes all over the place.
Note that this pull request also contains a backmerge of -rc3 to sort out
a few things in -next. I've also had to frob the shortlog a bit to exclude
anything that -rc3 brings in with this pull.
Regression wise we have a few strange bugs going on, but for all of them
closer inspection revealed that they've been pre-existing, just now
slightly more likely to be hit. And for most of them we have a patch
already. Otherwise QA has not reported any regressions, and I'm also not
aware of anything bad happening in 3.4.
* tag 'drm-intel-next-2012-04-23' of git://people.freedesktop.org/~danvet/drm-intel: (420 commits)
drm/i915: rc6 residency (fix the fix)
drm/i915/tv: fix open-coded ARRAY_SIZE.
drm/i915: invalidate render cache on gen2
drm/i915: Silence the change of LVDS sync polarity
drm/i915: add generic power management initialization
drm/i915: move clock gating functionality into intel_pm module
drm/i915: move emon functionality into intel_pm module
drm/i915: move drps, rps and rc6-related functions to intel_pm
drm/i915: fix line breaks in intel_pm
drm/i915: move watermarks settings into intel_pm module
drm/i915: move fbc-related functionality into intel_pm module
drm/i915: Refactor get_fence() to use the common fence writing routine
drm/i915: Refactor fence clearing to use the common fence writing routine
drm/i915: Refactor put_fence() to use the common fence writing routine
drm/i915: Prepare to consolidate fence writing
drm/i915: Remove the unsightly "optimisation" from flush_fence()
drm/i915: Simplify fence finding
drm/i915: Discard the unused obj->last_fenced_ring
drm/i915: Remove unused ring->setup_seqno
drm/i915: Remove fence pipelining
...
All supported devices have one issue that msi interrupt doesn't assert
if pci command register bit (PCI_COMMAND_INTX_DISABLE) is set.
Add workaround in drivers/pci/quirks.c
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intent of git commit 6fbf9e7a90
"PCI: Introduce __pci_reset_function_locked to be used when holding
device_lock." was to have a non-locking function that would call
pci_dev_reset function.
But it fell short of that by just probing and not actually reseting
the device. To make that work we need a way to move the lock
around device_lock to not be in pci_dev_reset (as the caller of
__pci_reset_function_locked already holds said lock). We do this by
renaming pci_dev_reset to __pci_dev_reset and bubbling said mutex out
of __pci_dev_reset to pci_dev_reset (a wrapper around __pci_dev_reset).
The __pci_reset_function_locked can now call __pci_dev_reset without
having to worry about the dead-lock.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A PCIe downstream port is a P2P bridge. Its secondary interface is
a link that should lead only to device 0 (unless ARI is enabled)[1], so
we don't probe for non-zero device numbers.
Some Stratus ftServer systems have a PCIe downstream port (02:00.0) that
leads to both an upstream port (03:00.0) and a downstream port (03:01.0),
and 03:01.0 has important devices below it:
[0000:02]-+-00.0-[03-3c]--+-00.0-[04-09]--...
\-01.0-[0a-0d]--+-[USB]
+-[NIC]
+-...
Previously, we didn't enumerate device 03:01.0, so USB and the network
didn't work. This patch adds a DMI quirk to scan all device numbers,
not just 0, below a downstream port.
Based on a patch by Prarit Bhargava.
[1] PCIe spec r3.0, sec 7.3.1
CC: Myron Stowe <mstowe@redhat.com>
CC: Don Dutile <ddutile@redhat.com>
CC: James Paradis <james.paradis@stratus.com>
CC: Matthew Wilcox <matthew.r.wilcox@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need a hook to release host bridge resources allocated when creating
root bus.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use that device for pci_root_bus bridge pointer.
Use pci_release_bus_bridge_dev() to release allocated pci_host_bridge in
remove path.
Use root bus bridge pointer to get host bridge pointer instead of searching
host bridge list. That leaves the host bridge list unused, so remove it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_host_bridge() looks like a C++ constructor. Also separate
find_pci_root_bus() out.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move host bridge-related code from probe.c to a new host-bridge.c.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull build fixes for less mainstream architectures from Paul Gortmaker:
"These are fixes for frv(1), blackfin(2), powerpc(1) and xtensa(4).
Fortunately the touches are nearly all specific to files just used by
the arch in question. The two touches to shared/common files
[kernel/irq/debug.h and drivers/pci/Makefile] are trivial to assess as
no risk to anyone.
Half of them relate to xtensa directly. It was only when I fixed the
last xtensa issue that I realized that the arch has been broken for a
significant time, and isn't a specific v3.4 regression. So if you
wanted, we could leave xtensa lying bleeding in the street for a
couple more weeks and queue those for 3.5. But given they are no risk
to anyone outside of xtensa, I figured to just leave them in.
If you are OK with taking the xtensa fixes, then please pull to get:
- one last implicit include uncovered by system.h that is in a file
specific to just one powerpc defconfig. (I'd sync'd with BenH).
- fix an oversight in the PCI makefile where shared code wasn't being
compiled for ARCH=frv
- fix a missing include for GPIO in blackfin framebuffer.
- audit and tag endif in blackfin ezkit board file, in order to find
and fix the misplaced endif masking a block of code.
- fix irq/debug.h choice of temporary macro names to be more internal
so they don't conflict with names used by xtensa.
- fix a reference to an undeclared local var in xtensa's signal.c
- fix an implicit bug.h usage in xtensa's asm/io.h uncovered by my
removing bug.h from kernel.h
- fix xtensa to properly indicate it is using asm-generic/hardirq.h
in order to resolve the link error - undefined ack_bad_irq
The xtensa still fails final link as my latest binutils does something
evil when ld forward-relocates unlikely() blocks, but in theory people
who have older/valid toolchains could now use the thing."
* 'for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
xtensa: fix build fail on undefined ack_bad_irq
blackfin: fix ifdef fustercluck in mach-bf538/boards/ezkit.c
blackfin: fix compile error in bfin-lq035q1-fb.c
pci: frv architecture needs generic setup-bus infrastructure
irq: hide debug macros so they don't collide with others.
xtensa: fix build error in xtensa/include/asm/io.h
xtensa: fix build failure in xtensa/kernel/signal.c
powerpc: fix system.h fallout in sysdev/scom.c [chroma_defconfig]
Otherwise we get this link failure for frv's defconfig:
LD .tmp_vmlinux1
drivers/built-in.o: In function `pci_assign_resource':
(.text+0xbf0c): undefined reference to `pci_cardbus_resource_alignment'
drivers/built-in.o: In function `pci_setup':
pci.c:(.init.text+0x174): undefined reference to `pci_realloc_get_opt'
pci.c:(.init.text+0x1a0): undefined reference to `pci_realloc_get_opt'
make[1]: *** [.tmp_vmlinux1] Error 1
Cc: David Howells <dhowells@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The default VGA device is a somewhat fluid concept on platforms with
multiple GPUs. Add support for setting it so switching code can update
things appropriately, and make sure that the sysfs code returns the right
device if it's changed.
v2: Updated to fix builds when __ARCH_HAS_VGA_DEFAULT_DEVICE is false.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: benh@kernel.crashing.org
Cc: airlied@redhat.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some shortcomings introduced into pci_restore_state() by commit
26f41062f2 ("PCI: check for pci bar restore completion and retry")
have been fixed by recent commit ebfc5b802f ("PCI: Fix regression in
pci_restore_state(), v3"), but that commit treats all PCI devices as
those with Type 0 configuration headers.
That is not entirely correct, because Type 1 and Type 2 headers have
different layouts. In particular, the area occupied by BARs in Type 0
config headers contains the secondary status register in Type 1 ones and
it doesn't make sense to retry the restoration of that register even if
the value read back from it after a write is not the same as the written
one (it very well may be different).
For this reason, make pci_restore_state() only retry the restoration
of BARs for Type 0 config headers. This effectively makes it behave
as before commit 26f41062f2 for all header types except for Type 0.
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 26f41062f2 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* one is a workaround that will be removed in v3.5 with proper fix in the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made them only
load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup in the
core code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPfyVUAAoJEFjIrFwIi8fJUjUH/jbY5JavRqSlNELZW2A4Ta76
8p00LqLHw/C56iHZcWKke8mqtWNb+ZfcQt7ZYcxDIYa4QWBL28x0OLAO2tOBIt37
ZjYESWSdFJaJvmpADluWtFyGyZ9TYJllDTBm/jWj1ZtKSZvR1YkhuMXCS0f4AmGQ
xFzSWJZUDdiOAqpN+VQD8wP00gfR8knQLg16XE2fvFdQo4XwpCtqLfHV/5pMMGdy
Cs/ep6rq/7cdv/nshKOcBnw7RW8l3Xoi/28ht8k3DvAQ2VtFq1Tugv2G9pcCHwQG
DIBkB3SOU6/v6P5at5+egKS5xR1fJetCWlkMd8kkbcdz2NPI4UDMkvOW6Q8yQls=
=6Ve+
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
The original XenoLinux code has always had things this way, and for
compatibility reasons (in particular with a subsequent pciback
adjustment) upstream Linux should behave the same way (allowing for two
distinct error indications to be returned by the backend).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since 3.2.12 and 3.3, some systems are failing to boot with a BUG_ON.
Some other systems using the pata_jmicron driver fail to boot because no
disks are detected. Passing pcie_aspm=force on the kernel command line
works around it.
The cause: commit 4949be1682 ("PCI: ignore pre-1.1 ASPM quirking when
ASPM is disabled") changed the behaviour of pcie_aspm_sanity_check() to
always return 0 if aspm is disabled, in order to avoid cases where we
changed ASPM state on pre-PCIe 1.1 devices.
This skipped the secondary function of pcie_aspm_sanity_check which was
to avoid us enabling ASPM on devices that had non-PCIe children, causing
trouble later on. Move the aspm_disabled check so we continue to honour
that scenario.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=42979 and
http://bugs.debian.org/665420
Reported-by: Romain Francoise <romain@orebokech.com> # kernel panic
Reported-by: Chris Holland <bandidoirlandes@gmail.com> # disk detection trouble
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Tested-by: Hatem Masmoudi <hatem.masmoudi@gmail.com> # Dell Latitude E5520
Tested-by: janek <jan0x6c@gmail.com> # pata_jmicron with JMB362/JMB363
[jn: with more symptoms in log message]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
acpi_dev_run_wake() is a generic function which can be used by
other subsystem too. Rename it to acpi_pm_device_run_wake, to be
consistent with acpi_pm_device_sleep_wake.
Then move it to ACPI core.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
- PV multiconsole support, so that there can be hvc1, hvc2, etc;
- P-state and C-state power management driver that uploads said
power management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPZ0qkAAoJEFjIrFwIi8fJjCgH/jeJ39E8ML8DP9tCS2HQnMqM
uTEjLcqvoJ7sEhHvtBLPeG2p0jyBvOWjLbSc7P8nESBAMPvSYol8L6WqfWrdSU4r
lHrma2sg9UYzRog5NyxAgkp7bBsBBFOnhVL3Cxb5Ig78cPWzeSWGpqGZ8M/d51Wf
1iE0tHuU4DpN+fg1SZqPqEm8ecEJ/eSrVTnyTx/Qo2Ak+Zw98SqzX7SV5lo8mudd
WFL1F2K9FyTNk79ndGhqFt36x6nEbFgMLbmCDWumLuWN6bMd1Uq0wNkCqW4F1h28
3yqnY+rfQh4y3eXK1B9nttCUTs+/66U5ZWrT6B1IJumGTAIqcWfgeUX/Vn/HVC4=
=tfMc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink breakage
reverted), dynamic debugging updates, w1 drivers, hyperv driver updates,
and a variety of other bits and pieces, full information in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9neCsACgkQMUfUDdst+ylyQwCfY2eizvzw5HhjQs8gOiBRDADe
yrgAnj1Zan2QkoCnQIFJNAoxqNX9yAhd
=biH6
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches for 3.4-rc1 from Greg KH:
"Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink
breakage reverted), dynamic debugging updates, w1 drivers, hyperv
driver updates, and a variety of other bits and pieces, full
information in the shortlog."
* tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (78 commits)
Tools: hv: Support enumeration from all the pools
Tools: hv: Fully support the new KVP verbs in the user level daemon
Drivers: hv: Support the newly introduced KVP messages in the driver
Drivers: hv: Add new message types to enhance KVP
regulator: Support driver probe deferral
Revert "sysfs: Kill nlink counting."
uevent: send events in correct order according to seqnum (v3)
driver core: minor comment formatting cleanups
driver core: move the deferred probe pointer into the private area
drivercore: Add driver probe deferral mechanism
DS2781 Maxim Stand-Alone Fuel Gauge battery and w1 slave drivers
w1_bq27000: Only one thread can access the bq27000 at a time.
w1_bq27000 - remove w1_bq27000_write
w1_bq27000: remove unnecessary NULL test.
sysfs: Fix memory leak in sysfs_sd_setsecdata().
intel_idle: Revert change of auto_demotion_disable_flags for Nehalem
w1: Fix w1_bq27000
driver-core: documentation: fix up Greg's email address
powernow-k6: Really enable auto-loading
powernow-k7: Fix CPU family number
...
In 5bfa14ed9f, I forgot to initialize res2.flags before calling
pcibios_bus_to_resource(), which depends on the resource type to locate the
correct aperture. This bug won't hurt x86, which currently never has an
offset between bus and CPU addresses, but will affect other architectures.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Right now we won't touch ASPM state if ASPM is disabled, except in the case
where we find a device that appears to be too old to reliably support ASPM.
Right now we'll clear it in that case, which is almost certainly the wrong
thing to do. The easiest way around this is just to disable the blacklisting
when ASPM is disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are PCIe devices on the market that report ARI support but
then fail to initialize correctly when ARI is actually used. This
leads to situations in which kernels 2.6.34 and newer fail to handle
systems where the previous kernels worked without any apparent
problems. Unfortunately, it is currently unknown how many such
devices are there.
For this reason, introduce a new kernel command line option,
pci=noari, allowing users to disable PCIe ARI altogether if they
see problems with PCIe device initialization.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_stop_bus_device gets called before in the same loop.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't switch to pci_remove_bus_device yet, keep the __ prefix for now
(the behavior is still the same: remove without stopping first).
This allows other out of tree users or pending patches to get notified
from compiler warning.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The old pci_remove_behind_bridge actually do stop and remove.
Make the name reflect that to reduce confusion.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The old pci_remove_bus_device actually did stop and remove.
Make the name reflect that to reduce confusion.
This patch is done by sed scripts and changes back some incorrect
__pci_remove_bus_device changes.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Makes it a little easier to figure out which device may have caused a
slow quirk.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This isn't really a quirk; calling it directly from pci_add_device makes
more sense.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ian Abbott
Joe Perches
Dave Airlie
Taku Izumi
Huang Ying
Yinghai Lu
Rafael J. Wysocki
Linus Torvalds
Bjorn Helgaas
Jiang Liu
Rafael J. Wysocki
Konrad Rzeszutek Wilk
Alan Stern
Thierry Reding
Gavin Shan
Konstantin Khlebnikov
Jiang Liu
Jan Beulich
Alan Cox
Feng Tang
Oliver Neukum
Stephen Hemminger
Shengzhou Liu
Paul Bolle
Lance Ortiz
Yijing Wang
Randy Dunlap
Masanari Iida
Chris Metcalf
Julia Lawall
Myron Stowe
Greg Ungerer
Nikhil P Rao
Zheng Yan
Wanpeng Li
Alex Williamson
Jan Kiszka
Amos Kong
Sebastian Andrzej Siewior
John Crispin
David S. Miller
Chunhe Lan
Daniel Vetter
Lin Ming
Khalid Aziz
Xudong Hao
Huang, Xiong
Paul Gortmaker
Matthew Garrett
Greg Kroah-Hartman
Matt Carlson