When running async rx handler the framework holds the mvm->mutex
before starting the async handler, that might cause a deadlock in case
the handler calls to ops that lock the mutex as well.
Add support for running async rx handler without hold the mutex before
activating the handler.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when the FW sends start/stop aux roc time event
notification with an error status, the driver returns an
error value, but does not remove the time event, and does
not notify the stack above that the time event is over.
This causes problems that the stack above assumes we are still
in the middle of a time event, and therefore can block different
events, such as scanning.
On FW failure notification, cleanup the time event parameters and
notify the stack above that the time event is over.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our hardware de-aggregates AMSDUs but copies the mac header
as it to the de-aggregated MPDUs. We need to turn off the AMSDU
bit in the QoS control ourselves.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add debugfs entries to get the ctdp budget average
and to stop ctdp.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
performance tests for hash map and per-cpu hash map
with and without pre-allocation
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
increase stress by also calling bpf_get_stackid() from
various *spin* functions
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
this test calls bpf programs from different contexts:
from inside of slub, from rcu, from pretty much everywhere,
since it kprobes all spin_lock functions.
It stresses the bpf hash and percpu map pre-allocation,
deallocation logic and call_rcu mechanisms.
User space part adding more stress by walking and deleting map elements.
Note that due to nature bpf_load.c the earlier kprobe+bpf programs are
already active while loader loads new programs, creates new kprobes and
attaches them.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helpers like ip_tunnel_info_opts_{get,set}() are only available if
CONFIG_INET is set, thus add an empty definition into the header for
the !CONFIG_INET case, where already other empty inline helpers are
defined.
This avoids ifdef kludge inside filter.c, but also vxlan and geneve
themself where this facility can only be used with, depend on INET
being set. For the !INET case TUNNEL_OPTIONS_PRESENT would never be
set in flags.
Fixes: 14ca0751c9 ("bpf: support for access to tunnel options")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
bpf: map pre-alloc
v1->v2:
. fix few issues spotted by Daniel
. converted stackmap into pre-allocation as well
. added a workaround for lockdep false positive
. added pcpu_freelist_populate to be used by hashmap and stackmap
this path set switches bpf hash map to use pre-allocation by default
and introduces BPF_F_NO_PREALLOC flag to keep old behavior for cases
where full map pre-allocation is too memory expensive.
Some time back Daniel Wagner reported crashes when bpf hash map is
used to compute time intervals between preempt_disable->preempt_enable
and recently Tom Zanussi reported a dead lock in iovisor/bcc/funccount
tool if it's used to count the number of invocations of kernel
'*spin*' functions. Both problems are due to the recursive use of
slub and can only be solved by pre-allocating all map elements.
A lot of different solutions were considered. Many implemented,
but at the end pre-allocation seems to be the only feasible answer.
As far as pre-allocation goes it also was implemented 4 different ways:
- simple free-list with single lock
- percpu_ida with optimizations
- blk-mq-tag variant customized for bpf use case
- percpu_freelist
For bpf style of alloc/free patterns percpu_freelist is the best
and implemented in this patch set.
Detailed performance numbers in patch 3.
Patch 2 introduces percpu_freelist
Patch 1 fixes simple deadlocks due to missing recursion checks
Patch 5: converts stackmap to pre-allocation
Patches 6-9: prepare test infra
Patch 10: stress test for hash map infra. It attaches to spin_lock
functions and bpf_map_update/delete are called from different contexts
Patch 11: stress for bpf_get_stackid
Patch 12: map performance test
Reported-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reported-by: Tom Zanussi <tom.zanussi@linux.intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
extend test coveraged to include pre-allocated and run-time alloc maps
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
note old loader is compatible with new kernel.
map_flags are optional
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
move ksym search from offwaketime into library to be reused
in other tests
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
map creation is typically the first one to fail when rlimits are
too low, not enough memory, etc
Make this failure scenario more verbose
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was observed that calling bpf_get_stackid() from a kprobe inside
slub or from spin_unlock causes similar deadlock as with hashmap,
therefore convert stackmap to use pre-allocated memory.
The call_rcu is no longer feasible mechanism, since delayed freeing
causes bpf_get_stackid() to fail unpredictably when number of actual
stacks is significantly less than user requested max_entries.
Since elements are no longer freed into slub, we can push elements into
freelist immediately and let them be recycled.
However the very unlikley race between user space map_lookup() and
program-side recycling is possible:
cpu0 cpu1
---- ----
user does lookup(stackidX)
starts copying ips into buffer
delete(stackidX)
calls bpf_get_stackid()
which recyles the element and
overwrites with new stack trace
To avoid user space seeing a partial stack trace consisting of two
merged stack traces, do bucket = xchg(, NULL); copy; xchg(,bucket);
to preserve consistent stack trace delivery to user space.
Now we can move memset(,0) of left-over element value from critical
path of bpf_get_stackid() into slow-path of user space lookup.
Also disallow lookup() from bpf program, since it's useless and
program shouldn't be messing with collected stack trace.
Note that similar race between user space lookup and kernel side updates
is also present in hashmap, but it's not a new race. bpf programs were
always allowed to modify hash and array map elements while user space
is copying them.
Fixes: d5a3b1f691 ("bpf: introduce BPF_MAP_TYPE_STACK_TRACE")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kprobe is placed on spin_unlock then calling kmalloc/kfree from
bpf programs is not safe, since the following dead lock is possible:
kfree->spin_lock(kmem_cache_node->lock)...spin_unlock->kprobe->
bpf_prog->map_update->kmalloc->spin_lock(of the same kmem_cache_node->lock)
and deadlocks.
The following solutions were considered and some implemented, but
eventually discarded
- kmem_cache_create for every map
- add recursion check to slow-path of slub
- use reserved memory in bpf_map_update for in_irq or in preempt_disabled
- kmalloc via irq_work
At the end pre-allocation of all map elements turned out to be the simplest
solution and since the user is charged upfront for all the memory, such
pre-allocation doesn't affect the user space visible behavior.
Since it's impossible to tell whether kprobe is triggered in a safe
location from kmalloc point of view, use pre-allocation by default
and introduce new BPF_F_NO_PREALLOC flag.
While testing of per-cpu hash maps it was discovered
that alloc_percpu(GFP_ATOMIC) has odd corner cases and often
fails to allocate memory even when 90% of it is free.
The pre-allocation of per-cpu hash elements solves this problem as well.
Turned out that bpf_map_update() quickly followed by
bpf_map_lookup()+bpf_map_delete() is very common pattern used
in many of iovisor/bcc/tools, so there is additional benefit of
pre-allocation, since such use cases are must faster.
Since all hash map elements are now pre-allocated we can remove
atomic increment of htab->count and save few more cycles.
Also add bpf_map_precharge_memlock() to check rlimit_memlock early to avoid
large malloc/free done by users who don't have sufficient limits.
Pre-allocation is done with vmalloc and alloc/free is done
via percpu_freelist. Here are performance numbers for different
pre-allocation algorithms that were implemented, but discarded
in favor of percpu_freelist:
1 cpu:
pcpu_ida 2.1M
pcpu_ida nolock 2.3M
bt 2.4M
kmalloc 1.8M
hlist+spinlock 2.3M
pcpu_freelist 2.6M
4 cpu:
pcpu_ida 1.5M
pcpu_ida nolock 1.8M
bt w/smp_align 1.7M
bt no/smp_align 1.1M
kmalloc 0.7M
hlist+spinlock 0.2M
pcpu_freelist 2.0M
8 cpu:
pcpu_ida 0.7M
bt w/smp_align 0.8M
kmalloc 0.4M
pcpu_freelist 1.5M
32 cpu:
kmalloc 0.13M
pcpu_freelist 0.49M
pcpu_ida nolock is a modified percpu_ida algorithm without
percpu_ida_cpu locks and without cross-cpu tag stealing.
It's faster than existing percpu_ida, but not as fast as pcpu_freelist.
bt is a variant of block/blk-mq-tag.c simlified and customized
for bpf use case. bt w/smp_align is using cache line for every 'long'
(similar to blk-mq-tag). bt no/smp_align allocates 'long'
bitmasks continuously to save memory. It's comparable to percpu_ida
and in some cases faster, but slower than percpu_freelist
hlist+spinlock is the simplest free list with single spinlock.
As expeceted it has very bad scaling in SMP.
kmalloc is existing implementation which is still available via
BPF_F_NO_PREALLOC flag. It's significantly slower in single cpu and
in 8 cpu setup it's 3 times slower than pre-allocation with pcpu_freelist,
but saves memory, so in cases where map->max_entries can be large
and number of map update/delete per second is low, it may make
sense to use it.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce simple percpu_freelist to keep single list of elements
spread across per-cpu singly linked lists.
/* push element into the list */
void pcpu_freelist_push(struct pcpu_freelist *, struct pcpu_freelist_node *);
/* pop element from the list */
struct pcpu_freelist_node *pcpu_freelist_pop(struct pcpu_freelist *);
The object is pushed to the current cpu list.
Pop first trying to get the object from the current cpu list,
if it's empty goes to the neigbour cpu list.
For bpf program usage pattern the collision rate is very low,
since programs push and pop the objects typically on the same cpu.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
if kprobe is placed within update or delete hash map helpers
that hold bucket spin lock and triggered bpf program is trying to
grab the spinlock for the same bucket on the same cpu, it will
deadlock.
Fix it by extending existing recursion prevention mechanism.
Note, map_lookup and other tracing helpers don't have this problem,
since they don't hold any locks and don't modify global data.
bpf_trace_printk has its own recursive check and ok as well.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek says:
====================
ipv6: per netns FIB6 walkers and garbage collector
Commit 2ac3ac8f86 ("ipv6: prevent fib6_run_gc() contention") reduced
the risk of contention on FIB6 garbage collector lock on systems with
many CPUs. However, one of our customers can still observe heavy
contention on fib6_gc_lock which can even trigger the soft lockup
detector.
This is caused by garbage collector running in forced mode from a timer.
While there is one timer per network namespace, the instances of
fib6_run_gc() running from them are protected by one global spinlock so
that only one garbage collector can run at any moment and other
namespaces have to wait. As most relevant data structures are separated
per netns, there is little reason for garbage collectors blocking each
other.
Similar problem exists for walkers: changes in one tree do not need to
adjust (and block) walkers traversing FIB trees in other namespaces.
This series separates both the walkers infrastructure and garbage
collector so that they work independently in network namespaces.
v2: get rid of ifdef in ipv6_route_seq_setup_walk(), pass net from
callers instead
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
One of our customers observed issues with FIB6 garbage collectors
running in different network namespaces blocking each other, resulting
in soft lockups (fib6_run_gc() initiated from timer runs always in
forced mode).
Now that FIB6 walkers are separated per namespace, there is no more need
for instances of fib6_run_gc() in different namespaces blocking each
other. There is still a call to icmp6_dst_gc() which operates on shared
data but this function is protected by its own shared lock.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 FIB data structures are separated per network namespace but
there is still only one global walkers list and one global walker list
lock. This means changes in one namespace unnecessarily interfere with
walkers in other namespaces.
Replace the global list with per-netns lists (and give each its own
lock).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global variable gc_args is only used in fib6_run_gc() and functions
called from it. As fib6_run_gc() makes sure there is at most one
instance of fib6_clean_all() running at any moment, we can replace
gc_args with a local variable which will be needed once multiple
instances (per netns) of garbage collector are allowed.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Updates for net-next.
Updates to support autoneg for all supported speeds, add PF port statistics,
and Advanced Error Reporting.
v2: Fixed patch 3 to not use parentheses on function return.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pci_error_handler callbacks to support for pcie advanced error
recovery.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the more useful port statistics in ethtool -S for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include some of the port error counters (e.g. crc) in ->ndo_get_stats64()
for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather periodic port statistics if the device is PF and link is up. This
is triggered in bnxt_timer() every one second to request firmware to DMA
the counters.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all autoneg speeds aupported by firmware to be advertised. If
the advertising parameter is 0, then all supported speeds will be
advertised.
Remove BNXT_ALL_COPPER_ETHTOOL_SPEED which is no longer used as all
supported speeds can be advertised.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The supported bits and advertising bits in ethtool have the same
definitions. The same is true for the firmware bits. So use the
common function to handle the conversion for both supported and
advertising bits.
v2: Don't use parentheses on function return.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And report actual pause settings to ETHTOOL_GPAUSEPARAM to let ethtool
resolve the actual pause settings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the conversion of pause bits and add one extra call layer so
that the same refactored function can be reused to get the link partner
advertisement bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix is for dsmark similar to commit 3557619f0f
("net_sched: prio: use qdisc_dequeue_peeked")
and makes use of qdisc_dequeue_peeked() instead of direct dequeue() call.
First time, wrr peeks dsmark, which will then peek into sfq.
sfq dequeues an skb and it's stored in sch->gso_skb.
Next time, wrr tries to dequeue from dsmark, which will call sfq dequeue
directly. This results skipping the previously peeked skb.
So changed dsmark dequeue to call qdisc_dequeue_peeked() instead to use
peeked skb if exists.
Signed-off-by: Kyeong Yoo <kyeong.yoo@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
1) Remove useless debug message when deleting IPVS service, from
Yannick Brosseau.
2) Get rid of compilation warning when CONFIG_PROC_FS is unset in
several spots of the IPVS code, from Arnd Bergmann.
3) Add prandom_u32 support to nft_meta, from Florian Westphal.
4) Remove unused variable in xt_osf, from Sudip Mukherjee.
5) Don't calculate IP checksum twice from netfilter ipv4 defrag hook
since fixing af_packet defragmentation issues, from Joe Stringer.
6) On-demand hook registration for iptables from netns. Instead of
registering the hooks for every available netns whenever we need
one of the support tables, we register this on the specific netns
that needs it, patchset from Florian Westphal.
7) Add missing port range selection to nf_tables masquerading support.
BTW, just for the record, there is a typo in the description of
5f6c253ebe ("netfilter: bridge: register hooks only when bridge
interface is added") that refers to the cluster match as deprecated, but
it is actually the CLUSTERIP target (which registers hooks
inconditionally) the one that is scheduled for removal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
BPF updates
Couple of misc updates to BPF, besides others this series adds
bpf_csum_diff() to be used with L3 csums, allows for managing
tunnel options for collect meta data mode, and enabling ipv6
traffic class for collect meta data in vxlan specifically (geneve
already supports it). For more details, please see individual
patches.
The series requires net to be merged into net-next first to
avoid any further pending merge conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can already do that for IPv4, but IPv6 support was missing. Add
it for vxlan, so it can be used with collect metadata frontends.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumptions from commit 0c1d70af92 ("net: use dst_cache for vxlan
device"), 468dfffcd7 ("geneve: add dst caching support") and 3c1cb4d260
("net/ipv4: add dst cache support for gre lwtunnels") on dst_cache usage
when ip_tunnel_info is used is unfortunately not always valid as assumed.
While it seems correct for ip_tunnel_info front-ends such as OVS, eBPF
however can fill in ip_tunnel_info for consumers like vxlan, geneve or gre
with different remote dsts, tos, etc, therefore they cannot be assumed as
packet independent.
Right now vxlan, geneve, gre would cache the dst for eBPF and every packet
would reuse the same entry that was first created on the initial route
lookup. eBPF doesn't store/cache the ip_tunnel_info, so each skb may have
a different one.
Fix it by adding a flag that checks the ip_tunnel_info. Also the !tos test
in vxlan needs to be handeled differently in this context as it is currently
inferred from ip_tunnel_info as well if present. ip_tunnel_dst_cache_usable()
helper is added for the three tunnel cases, which checks if we can use dst
cache.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd7 ("geneve: add dst caching support")
Fixes: 3c1cb4d260 ("net/ipv4: add dst cache support for gre lwtunnels")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c3345407 ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added by 9a628224a6 ("ip_tunnel: Add dont fragment flag."), allow to
feed df flag into tunneling facilities (currently supported on TX by
vxlan, geneve and gre) as a hint from eBPF's bpf_skb_set_tunnel_key()
helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are only used here, so there's no reason they should not be static.
Only the vlan push/pop protos are used in the test_bpf suite.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When overwriting parts of the packet with bpf_skb_store_bytes() that
were fed previously into skb->hash calculation, we should clear the
current hash with skb_clear_hash(), so that a next skb_get_hash() call
can determine the correct hash related to this skb.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7d672345ed ("bpf: add generic bpf_csum_diff helper") added a
generic checksum diff helper that can feed bpf_l4_csum_replace() with
a target __wsum diff that is to be applied to the L4 checksum. This
facility is very flexible, can be cascaded, allows for adding, removing,
or diffing data, or for calculating the pseudo header checksum from
scratch, but it can also be reused for working with the IPv4 header
checksum.
Thus, analogous to bpf_l4_csum_replace(), add a case for header field
value of 0 to change the checksum at a given offset through a new helper
csum_replace_by_diff(). Also, in addition to that, this provides an
easy to use interface for feeding precalculated diffs f.e. coming from
a map. It nicely complements bpf_l3_csum_replace() that currently allows
only for csum updates of 2 and 4 byte diffs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The cw1200 uses #ifdef to check for CONFIG_PM, but then
uses SIMPLE_DEV_PM_OPS, which leaves the references out when
CONFIG_PM_SLEEP is not defined, so we get a warning with
PM=y && PM_SLEEP=n:
drivers/net/wireless/st/cw1200/cw1200_spi.c:450:12: error: 'cw1200_spi_suspend' defined but not used [-Werror=unused-function]
This removes the incorrect #ifdef and instead uses a __maybe_unused
annotation to let the compiler know it can silently drop
the function definition.
For the DEV_PM_OPS definition, we can use an IS_ENABLED() check
to avoid defining the structure when CONFIG_PM is not set without
the #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch reports the following warning:
CHECK drivers/net/wireless/realtek/rtlwifi/rc.c
drivers/net/wireless/realtek/rtlwifi/rc.c:144 _rtl_rc_rate_set_series() warn: impossible condition '(wireless_mode == 256) => (0-255 == 256)'
This warning arises because commit acc6907b87a9 ("rtlwifi: Fix warning
from ieee80211_get_tx_rates() when using 5G") now checks the wireless
mode for WIRELESS_MODE_AC_ONLY (BIT(8)) in _rtl_rc_rate_set_series().
As a result, all quantities used to store the wireless mode must be u16.
This patch also reorders struct rtl_sta_info to save a little space.
Fixes: d76d65fd26 ("rtlwifi: fix broken VHT support")
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) Fix ordering of WEXT netlink messages so we don't see a newlink
after a dellink, from Johannes Berg.
2) Out of bounds access in minstrel_ht_set_best_prob_rage, from
Konstantin Khlebnikov.
3) Paging buffer memory leak in iwlwifi, from Matti Gottlieb.
4) Wrong units used to set initial TCP rto from cached metrics, also
from Konstantin Khlebnikov.
5) Fix stale IP options data in the SKB control block from leaking
through layers of encapsulation, from Bernie Harris.
6) Zero padding len miscalculated in bnxt_en, from Michael Chan.
7) Only CHECKSUM_PARTIAL packets should be passed down through GSO, fix
from Hannes Frederic Sowa.
8) Fix suspend/resume with JME networking devices, from Diego Violat
and Guo-Fu Tseng.
9) Checksums not validated properly in bridge multicast support due to
the placement of the SKB header pointers at the time of the check,
fix from Álvaro Fernández Rojas.
10) Fix hang/tiemout with r8169 if a stats fetch is done while the
device is runtime suspended. From Chun-Hao Lin.
11) The forwarding database netlink dump facilities don't track the
state of the dump properly, resulting in skipped/missed entries.
From Minoura Makoto.
12) Fix regression from a recent 3c59x bug fix, from Neil Horman.
13) Fix list corruption in bna driver, from Ivan Vecera.
14) Big endian machines crash on vlan add in bnx2x, fix from Michal
Schmidt.
15) Ethtool RSS configuration not propagated properly in mlx5 driver,
from Tariq Toukan.
16) Fix regression in PHY probing in stmmac driver, from Gabriel
Fernandez.
17) Fix SKB tailroom calculation in igmp/mld code, from Benjamin
Poirier.
18) A past change to skip empty routing headers in ipv6 extention header
parsing accidently caused fragment headers to not be matched any
longer. Fix from Florian Westphal.
19) eTSEC-106 erratum needs to be applied to more gianfar chips, from
Atsushi Nemoto.
20) Fix netdev reference after free via workqueues in usb networking
drivers, from Oliver Neukum and Bjørn Mork.
21) mdio->irq is now an array rather than a pointer to dynamic memory,
but several drivers were still trying to free it :-/ Fixes from
Colin Ian King.
22) act_ipt iptables action forgets to set the family field, thus LOG
netfilter targets don't work with it. Fix from Phil Sutter.
23) SKB leak in ibmveth when skb_linearize() fails, from Thomas Falcon.
24) pskb_may_pull() cannot be called with interrupts disabled, fix code
that tries to do this in vmxnet3 driver, from Neil Horman.
25) be2net driver leaks iomap'd memory on removal, fix from Douglas
Miller.
26) Forgotton RTNL mutex unlock in ppp_create_interface() error paths,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (97 commits)
ppp: release rtnl mutex when interface creation fails
cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind
tcp: fix tcpi_segs_in after connection establishment
net: hns: fix the bug about loopback
jme: Fix device PM wakeup API usage
jme: Do not enable NIC WoL functions on S0
udp6: fix UDP/IPv6 encap resubmit path
be2net: Don't leak iomapped memory on removal.
vmxnet3: avoid calling pskb_may_pull with interrupts disabled
net: ethernet: Add missing MFD_SYSCON dependency on HAS_IOMEM
ibmveth: check return of skb_linearize in ibmveth_start_xmit
cdc_ncm: toggle altsetting to force reset before setup
usbnet: cleanup after bind() in probe()
mlxsw: pci: Correctly determine if descriptor queue is full
mlxsw: spectrum: Always decrement bridge's ref count
tipc: fix nullptr crash during subscription cancel
net: eth: altera: do not free array priv->mdio->irq
net/ethoc: do not free array priv->mdio->irq
net: sched: fix act_ipt for LOG target
asix: do not free array priv->mdio->irq
...
Pull overlayfs fixes from Miklos Szeredi:
"Overlayfs bug fixes. All marked as -stable material"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: copy new uid/gid into overlayfs runtime inode
ovl: ignore lower entries when checking purity of non-directory entries
ovl: fix getcwd() failure after unsuccessful rmdir
ovl: fix working on distributed fs as lower layer
This reverts commit dbb17a21c1.
It turns out that commit can cause problems for systems with multiple
GPUs, and causes X to hang on at least a HP Pavilion dv7 with hybrid
graphics.
This got noticed originally in 4.4.4, where this patch had already
gotten back-ported, but 4.5-rc7 was verified to have the same problem.
Alexander Deucher says:
"It looks like you have a muxed system so I suspect what's happening is
that one of the display is being reported as connected for both the
IGP and the dGPU and then the desktop environment gets confused or
there some sort problem in the detect functions since the mux is not
switched to the dGPU. I don't see an easy fix unless Dave has any
ideas. I'd say just revert for now"
Reported-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: stable@kernel.org # wherever dbb17a21c1 got back-ported
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing rtnl_unlock() in the error path of ppp_create_interface().
Fixes: 58a89ecaca ("ppp: fix lockdep splat in ppp_dev_uninit()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.
Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.
Fixes: 8a34b0ae87 ("usbnet: cdc_ncm: apply usbnet_link_change")
Reported-by: Andrey Konovalov <andreyknvl@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
If final packet (ACK) of 3WHS is lost, it appears we do not properly
account the following incoming segment into tcpi_segs_in
While we are at it, starts segs_in with one, to count the SYN packet.
We do not yet count number of SYN we received for a request sock, we
might add this someday.
packetdrill script showing proper behavior after fix :
// Tests tcpi_segs_in when 3rd packet (ACK) of 3WHS is lost
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
+.020 < P. 1:1001(1000) ack 1 win 32792
+0 accept(3, ..., ...) = 4
+.000 %{ assert tcpi_segs_in == 2, 'tcpi_segs_in=%d' % tcpi_segs_in }%
Fixes: 2efd055c53 ("tcp: add tcpi_segs_in and tcpi_segs_out to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chaya Rachel Ivgi
Matti Gottlieb
Sara Sharon
Alexei Starovoitov
Daniel Borkmann
David S. Miller
Michal Kubeček
Satish Baddipadige
Michael Chan
Kyeong Yoo
Arnd Bergmann
Larry Finger
Linus Torvalds
Guillaume Nault
Bjørn Mork
Eric Dumazet