After ti-opp-supply driver is in place to provide AVS Class0 and abb
regulator scaling support let's enable 1.5GHz for the cpu.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the OPP supply node for the MPU voltage rail to provide the
information needed by the ti-opp-supply driver to enable AVS Class 0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a vbb-supply phandle to the cpus node and also add an additional
triplet of voltages for each OPP in the operating-points-v2 table to
make use of the multi regulator support in the OPP core and provide the
vbb regulator for use by the ti-opp-supply driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBone Blue: can: enable the dedicated can connector.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBone Blue: usarts: enable all the dedicated usart connectors.
DSM2/uart4: on the Blue, this is a recieve only interface.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the correct IRQ gpio pin on the BeagleBone Blue to allow the
wl1835 wireless module to actually work.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since SoC specific compatible strings are used for PCIe in
dra74x.dtsi and dra72x.dtsi, remove the compatible property
from dra7.dtsi which uses the deprecated compatible string.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA76 EVM has a 4-lane PCIe connector and DRA76 can support x2 lanes.
Enable both the PCIe lanes here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use dra72 specific compatible string for PCIe while preserving
the older compatible.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use dra74 specific compatible string for PCIe while preserving
the older compatible. While at that add a new label for the
2nd instance of pcie.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ti,syscon-lane-sel and ti,syscon-lane-conf properties specific to enable
PCIe x2 lane mode are added here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am574x-idk is similar to am572x-idk with am574x SoC. So create
a common file for both evms and include SoC dtsi as needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x IDK has a TPS386000 supply voltage supervisor on the VDD_MPU rail
set to trigger undervoltage condition at 0.96V. Because of this, OPP50,
which is normally configured to 300MHz at 0.95V, must be disabled to
avoid triggering the undervoltage condition. Also mark OPP100 as the
suspend-opp as it is now our lowest OPP.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can remove the unnecessary "omapdss," prefix because
the omapdrm driver takes care of it when matching with
the driver table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Official vendor string is now "tpo" and not "toppoly".
Requires patch "omapdrm: panel: fix compatible vendor string for td028ttec1"
so that the driver understands both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic panel support for the Nokia N950. It must be tweaked a
little bit later, since the panel was built into the device
upside-down. Also the first 5 and the last 5 pixels are covered
by plastic.
Signed-off-By: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This improves LCD support for the Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have
leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have
leading 0s
Converted using the following command:
$ find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec \
sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" \
-e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format
error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The newly added OMAP35xx Torpedo does not have a WiFi option, so
this patch moves the WL1283 binding and pin muxing to the
logicpd-torpedo-37xx-devkit since it's only applicable on that SOM
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the common baseboard info moved into its own file and the
common torpedo already in its own file, we can very easily
create a new devkit specific for the OMAP35xx.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Development kits consist of a SOM connected to a baseboard. Moving most
of the devkit files to baseboard allow us to re-use much of the contents in
preparation for using it on the OMAP35xx varation of the same kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the common baseboard info moved into its own file and the common SOM-LV
already in its own file, we can very easily create a new devkit specific
for the OMAP35xx.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Development kits consist of a SOM connected to a baseboard. Moving most
of the devkit files to baseboard allow us to re-use much of the contents in
preparation for using it on the OMAP35xx varation of the same kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: updated to apply on recent gpmc range fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The audio DMA request for hdmi is crossbar 76 and we use sDMA
to handle the data transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The metastability workaround causes Erratic errors [1]
on the HighSpeed USB PHY which can cause upto 2 seconds
delay in enumerating to a USB host while in Gadget mode.
Disable the Run/Stop metastability workaround to avoid this
ill effect. We are aware that this opens up the opportunity
for Run/Stop metastability, however this issue has never been
observed in TI releases so we think that Run/Stop metastability
is a lesser evil than the PHY Erratic errors. So disable it.
[1] USB controller trace during gadget enumeration
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event
(00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux/intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since U-Boot passes this information to the kernel, let's remove
the partition information from the device tree for
logicpd-torpedo-37xx-devkit and logicpd-som-lv-37xx-devkit
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 14e3e295b2 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d05 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following warnings:
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pin assignment for the wl127x interrupt was incorrect. I am
not sure how this every worked. This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working. This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.
Fixes: 44e4716499 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.
This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.
Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.
Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457f3 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.
Fixes: 7136d457f3 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM fixes from Russell King:
- LPAE fixes for kernel-readonly regions
- Fix for get_user_pages_fast on LPAE systems
- avoid tying decompressor to a particular platform if DEBUG_LL is
enabled
- BUG if we attempt to return to userspace but the to-be-restored PSR
value keeps us in privileged mode (defeating an issue that ftracetest
found)
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: BUG if jumping to usermode address in kernel mode
ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
ARM: make decompressor debug output user selectable
ARM: fix get_user_pages_fast
Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode. This
could occur due to corrupted stack state, which has been observed with
"ftracetest".
This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
- Use pwd instead of /bin/pwd for portability
- Clean up Makefiles
- Fix ld-option for clang
- Fix malloc'ed data size in Kconfig
- Fix parallel building along with coccicheck
- Fix a minor issue of package building
- Prompt to use "rpm-pkg" instead of "rpm"
- Clean up *.i and *.lst patterns by "make clean"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a2Td
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- use 'pwd' instead of '/bin/pwd' for portability
- clean up Makefiles
- fix ld-option for clang
- fix malloc'ed data size in Kconfig
- fix parallel building along with coccicheck
- fix a minor issue of package building
- prompt to use "rpm-pkg" instead of "rpm"
- clean up *.i and *.lst patterns by "make clean"
* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: drop $(extra-y) from real-objs-y
kbuild: clean up *.i and *.lst patterns by make clean
kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
kbuild: pkg: use --transform option to prefix paths in tar
coccinelle: fix parallel build with CHECK=scripts/coccicheck
kconfig/symbol.c: use correct pointer type argument for sizeof
kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
kbuild: remove all dummy assignments to obj-
kbuild: create built-in.o automatically if parent directory wants it
kbuild: /bin/pwd -> pwd
Tony Lindgren
Dave Gerlach
Robert Nelson
Kishon Vijay Abraham I
Lokesh Vutla
H. Nikolaus Schaller
Sebastian Reichel
Peter Ujfalusi
Mathieu Malaterre
Adam Ford
Roger Quadros
Keerthy
Andrew F. Davis
Linus Torvalds
Russell King