The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>). To fix this,
revert 2c5643b1c5 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.
This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>. However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).
Build tested on 32- and 64-bit x86 allmodconfig.
Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
The ACPI notification we get from rfkill events on these machines gives
us all the information we need to identify the port that's changed. Do
so rather than assuming that it's always bus 1.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The new style brightness control provides an operating range of 9 values
(seems consistent over a large number of models sharing the same
brightness control methods).
Read and use the minimum and maximum values to limit the backlight
interface between those boundaries.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Check if we were successful in setting the requested brightness and
report failure in that case.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The newer Lenovo ThinkPads have HKEY HID of LEN0068 instead
of IBM0068. Added new HID so that thinkpad_acpi module will
auto load on these newer Lenovo ThinkPads.
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
MXM is a laptop graphics card form-factor + interface specification,
this adds an initial stub driver to talk to the MXM WMI interface.
The only method used is the MUX switching method needed to do switchable
graphics on the nvidia chipsets.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
thinkpad-acpi fails to load with newer Thinkpad X201s BIOS
acer-wmi: Fix capitalisation of GUID in module alias
sony-laptop: keyboard backlight fixes
sony-laptop: only show the handles sysfs file in debug mode
samsung-laptop: set backlight type
staging: samsung-laptop has moved to platform/x86
samsung-laptop: Samsung R410P backlight driver
samsung-laptop: add support for N230 model
platform-drivers: x86: pmic: Restore the dropped buslock/unlock
sony-laptop: fix early NULL pointer dereference
msi-laptop: fix config-dependent build error
eeepc-wmi: add keys found on EeePC 1215T
asus-wmi: swap input name and phys
asus-laptop: remove removed features from feature-removal-schedule.txt
The new BIOS has a slightly different EC version string.
From a1541710300b083a1a9acff2890d721d15ede62b Mon Sep 17 00:00:00 2001
From: Keith Packard <keithp@keithp.com>
Date: Sun, 13 Mar 2011 23:46:22 -0700
Subject: [PATCH] thinkpad-acpi: Some BIOS versions don't end in WW, remove check
My X201s BIOS version string is 6QET46V1 (1.16 ). The
EC version string is 6QHT28WW-1.09. The driver was requiring that both
of these have 'WW' in positions 6 and 7. I don't know what the
significance of having 'V1' there instead is, but removing the test
makes the driver load on my machine.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
wmi:6AF4F258-B401-42Fd-BE91-3D4AC2D7C0D3 needs to be
wmi:6AF4F258-B401-42FD-BE91-3D4AC2D7C0D3 in module alias for acer-wmi is
automatically loaded.
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Restore the original state on module removal, set the latest values on
resume.
When setting the keyboard backlight mode try to turn on/off backlight
immediately.
[malattia@linux.it: patch taken from a largely modified sony-laptop.c,
ported and slightly modified to use defines already available.]
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
It makes no sense to expose this type of information to userspace unless
the driver was explicitly loaded with the debug option.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cherry-picked from drivers/staging/samsung-laptop/samsung-laptop.c
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Here's a trivial patch which adds support to the backlight device found
in Samsung R410 Plus laptops.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[mmarek: cherry-picked from staging commit d542f180]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[mmarek: cherry-picked from staging commit 0789b003]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
When I added the buslock/unlock mechanism to the pmic code in order to
get rid of the horrible work queue stuff, stupid me missed to add the
new callbacks to the irq_chip.
In consequence Andrew removed the unused functions, but I missed that.
Add them back and hook them up proper.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The SNC acpi driver could get early notifications before it fully
initializes and that could lead to dereferencing the sony_nc_handles
structure pointer that is still NULL at that stage.
Make sure we return early from the handle lookup function in these
cases.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The msi-laptop driver uses input_*() and sparse_keymap_*() interfaces.
It should depend on the INPUT subsystem being present and select
INPUT_SPARSEKMAP so that those interfaces are present.
ERROR: "input_free_device" [drivers/platform/x86/msi-laptop.ko] undefined!
ERROR: "input_register_device" [drivers/platform/x86/msi-laptop.ko] undefined!
ERROR: "sparse_keymap_setup" [drivers/platform/x86/msi-laptop.ko] undefined!
ERROR: "input_allocate_device" [drivers/platform/x86/msi-laptop.ko] undefined!
ERROR: "sparse_keymap_report_event" [drivers/platform/x86/msi-laptop.ko] undefined!
ERROR: "input_unregister_device" [drivers/platform/x86/msi-laptop.ko] undefined!
ERROR: "sparse_keymap_free" [drivers/platform/x86/msi-laptop.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: "Lee, Chun-Yi" <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
static void acpi_ec_gpe_query(void *ec_cxt);
-> The function is right above this declaration -> not needed.
poll_force is also not used, cleaned up in ec.c and its users:
compal-laptop and msi-laptop.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This is what I intended to do since:
1) the driver handles variable waits just fine, and
2) interruptible waits aren't reported as load in the load avg.
Reported-and-tested-by: Andreas Hartmann <andihartmann@freenet.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acer WMI hotkey event's result include current device status, just
need sync the status to killswitch after acer-wmi driver receive
hotkey event but not always poll device status. This is good for
performance.
But, if use EC raw mode, Acer BIOS will not emit wmi event and
leave EC to control device status. So, still startup polling job
when doesn't detect WMI event GUID or user choice to use ec_raw_mode.
Tested on Acer TravelMate 8572 notebook.
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acer BIOS keeps devices state when system reboot, but reset to default
device states (Wlan on, Bluetooth off, wwan on) if system cold boot.
That means BIOS's initial state is not always real persistence.
So, removed rfkill_init_sw_state because it sets initial state to
persistence then replicate to other new killswitch when rfkill-input
enabled.
After removed it, acer-wmi set initial soft-block state after rfkill
register, and doesn't allow set_block until rfkill initial finished.
Reference: bko#31002
https://bugzilla.kernel.org/show_bug.cgi?id=31002
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: OldÅich JedliÄka <oldium.pro@seznam.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In the earlier check we assumed that "obj" could be NULL. I looked at
some of the other places that call evaluate_object() and they check
for NULL as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
"err" needs to be signed for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
dmi_check_system() walks the table running matching functions until
someone returns non zero or we hit the end.
This patch makes dmi_check_cb to return 1 so dmi_check_system() return
immediately when a match is found.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
I found the commit 80183a4b
"compal-laptop/fujitsu-laptop/msi-laptop: make dmi_check_cb to return 1 instead of 0"
has wrong patch merge.
The original patch change the return value for dmi_check_cb():
https://lkml.org/lkml/2010/7/2/88
But commit 80183a4b changed the return value for set_backlight_level.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This adds the samsung-laptop driver to the kernel. It now supports
all known Samsung laptops that use the SABI interface.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch change WMI ID to upper characters. With this patch module
acer-wmi is automatically loaded when WMI ID is detected.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch deactive mail led when laptop is going to hibernete/suspend
or power off. After resume from hibernate/suspend correctly restore
mail led state.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
MSI BIOS's raw behavior is send out KEY_TOUCHPAD_TOGGLE key when user
pressed touchpad hotkey.
Actually, we can capture the real touchpad status by read 0xE4 EC address
on MSI netbook/notebook. So, add msi-laptop input device for send out
KEY_TOUCHPAD_ON or KEY_TOUCHPAD_OFF key when user pressed Fn+F3 touchpad
hotkey. It leave userland applications to know the real touchpad status.
Tested on MSI netbook U-100, U-115, U160(N051), U160DX, N014, N034
Tested on MSI notebook CR620
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Set the touchpad toggle key code from F22 to KEY_TOUCHPAD_TOGGLE,
and userspace should use udev's key re-mapping facilities while X
is unable to process keycodes above 255 to adjust to the keycode.
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In the original code, if "device_enum" was NULL then it would
dereference it when it printed the error message.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Return -ENOMEM if kzalloc() fails. The callers already handle error
returns.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There were two places in sony_nc_add() where we returned zero on failure
instead of a negative error code.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Sparse complains that these variables should be static.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=25922
On ideapad Y530, the brightness key notify will be blocked if the last notify
is not responsed by getting the brightness value. Read value when we get the
notify shall fix the problem and will not have any difference on other ideapads.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix eeepc-wmi build when CONFIG_HOTPLUG_PCI is not enabled:
eeepc-wmi.c:(.text+0x3bc5e9): undefined reference to `pci_hp_deregister'
eeepc-wmi.c:(.text+0x3bcca4): undefined reference to `__pci_hp_register'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
I also found some leds ids (0x00020011-0x00020016 and 0x00040015),
but since they are not really present on the notebook,
I can't guess their name .
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Introduce a new driver for Asus Notebooks shipped with
a WMI device instead of the old ACPI device. The WMI
device is almost the same as the one present in Eee PC,
but the event guid and the keymap are different.
The keymap comes from asus-laptop module.
On Asus notebooks, when you call the WMI device, you always
need a 64bit buffer, even if you only want to get the state
of a device (tested on a G73).
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
INIT() call is needed to enable hotkeys on G73
SPEC() and SFUN() allow us to know more about
available features.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This is tricky, new WMI aware notebooks seems to use
0x53545344 while Eee PCs are using 0x53544344. But there
is no way to know if there is an Eee PC in that wild that is
using 0x53545344 or a notebook using 0x53544344. So the
driver try to guess the available DSTS method ... But most Eee PCs
never return 0xFFFFFFFE when a method is not available, they return
0 instead (and that's useless).
So, first, try 0x53544344 then 0x53545344. We will find
a better way when we got more data.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch create a single function to call the
WMI methods. This function handle inexistent methods (when
implemented by the WMI devices, and this is not the case on
Eee PCs), ACPI errors, etc..
Also pack struct bios_arg, and make sure that we always send
a 64bit buffer when calling a WMI method, because this is
needed on Asus notebooks.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
First, this allow use to remove the custom asusrfkill_wlan_query,
but this will also allow us to give struct asus_wmi * to
get_devstate/set_devstate later.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
New Asus notebooks are using a WMI device similar to
the one used in Eee PCs. Since we don't want to load
eeepc-wmi module on Asus notebooks, and we want to
keep the eeepc-wmi module for backward compatibility,
this patch introduce a new module, named asus-wmi, that
will be used by eeepc-wmi and the new Asus Notebook WMI
Driver.
eeepc-wmi's input device strings (device name and phys)
are kept, but rfkill and led names are changed (s/eeepc/asus/).
This should not break anything since rfkill are used by type or
index, not by name, and the eeepc::touchpad led wasn't working
correctly before 2.6.39 anyway.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
New Asus notebooks are using a WMI device similar to
the one used in Eee PCs. Since we don't want to load
a module named eeepc-laptop on Asus Notebooks, start by
copying all the code to asus-wmi.c.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This is the basic thermal sensor driver for Intel MID platform using the
Medfield chipset. It plugs in via the thermal drivers and provides sensor
readings for the device sensors.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some recent HP laptops use a new wireless query command type 0x1b.
Add support for it. Tested on HP Mini 5102.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
hp_wmi_rfkill_setup cleans up after itself now, so failing completely is
no longer necessary.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
NULLify rfkill pointers during initialization. This prevents dereference
of invalid pointer in case the driver is rebound and some rfkill device
isn't detected anymore. Clear them also in hp_wmi_rfkill_setup failure
path so that an rfkill initialization failure doesn't need to be fatal
for the whole driver.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Split initialization of rfkill devices from hp_wmi_bios_setup() to
hp_wmi_rfkill_setup(). This makes the code somewhat cleaner, especially
with the future command 0x1b rfkill support.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Split buffersize parameter of hp_wmi_perform_query to insize and
outsize. Existing callers are changed to use the same value for insize
and outsize to avoid any regressions, with the exception of
hp_wmi_set_block where the output buffer is unused and therefore outsize
is set to 0 (this change is not seen by BIOS code).
The maximum input buffer size is kept at 4 bytes as per struct
bios_args. Some commands exist that take longer buffers, but they
haven't been implemented. The data portion of bios_args can be trivially
made dynamically allocated later when such larger buffers become needed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Remove the status variable from hp_wmi_perform_query which holds the
return value from wmi_evaluate_method(). It is never checked as the
function bails out if the output buffer hasn't been allocated which
indicates the call failed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Check BIOS provided return value code in hp_wmi_perform_query and print
a warning on error. Printing is suppressed for HPWMI_RET_UNKNOWN_CMDTYPE
which is returned when the command type is unsupported.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reasonably recent Vaios have a 0x12f or 0x137 handler that exposes a
fine lid backlight regulation with values ranging from 0 to 255.
The patch is based on findings and code from Javier Achirica
<achirica@gmail.com> and Marco Chiappero <marco@absence.it>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Recent Vaios have the opportunity to control the keyboard backlight via
ACPI calls to the SNC device.
Introduce two module parameters to control how keyboard backlight should
be set at module loading (default to on and with 10 seconds timeout).
Tested-by: Marco Chiappero <marco@absence.it>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Avoid calling into acpi each time we need to lookup a method handle
and report the available handles to ease collection of information when
debugging issues. Also move initialization of the platform driver
earlier to allow adding files from other setup functions.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There is not much use for these events in userspace and handling the
events themselves seems to get in the way of the actual activation of
the rf devices. The SNC device doesn't expose them already.
https://bugzilla.kernel.org/show_bug.cgi?id=15303
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
intel_mid_powerbtn.c uses input interfaces, so it should depend
on INPUT to fix build errors when CONFIG_INPUT is not enabled:
intel_mid_powerbtn.c:(.text+0x56ca8f): undefined reference to `input_event'
intel_mid_powerbtn.c:(.devinit.text+0x2e7b4): undefined reference to `input_allocate_device'
intel_mid_powerbtn.c:(.devinit.text+0x2e7ff): undefined reference to `input_set_capability'
intel_mid_powerbtn.c:(.devinit.text+0x2e84a): undefined reference to `input_register_device'
intel_mid_powerbtn.c:(.devinit.text+0x2e88b): undefined reference to `input_free_device'
intel_mid_powerbtn.c:(.devexit.text+0x42f0): undefined reference to `input_unregister_device'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hong Liu <hong.liu@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Enable volume up and down hotkeys on WMI events
GUID 284A0E6B-380E-472A-921F-E52786257FB4 and
GUID 02314822-307C-4F66-bf0E-48AEAEB26CC8.
Also works around a firmware bug where the _WED method
should return an integer containing the key code and in fact
the method returns the key code in element zero of a buffer.
BugLink: http://bugs.launchpad.net/bugs/701530
BugLink: http://bugs.launchpad.net/bugs/676997
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The power button is connected to MSIC on Medfield, we will get two
interrupts from IOAPIC when pressing or releasing the power button.
Signed-off-by: Hong Liu <hong.liu@intel.com>
[Minor fixes as noted by Dmitry]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
These keys are supposed to be handled by any software
using the camera (like webKam or cheese...). They can
also be used to actually move the camera when possible.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Each device seems to be in a "group" (devid >> 16 & 0xFF).
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
I should have done that one year ago, so it's more than
time to do it.
These two features use non-standard interfaces. There are the
only features that really need multiple path to guess what's
the right method name on a specific laptop.
Removing them allow to remove a lot of code an significantly
clean the driver.
This will affect the backlight code which won't be able to know
if the backlight is on or off.
The platform display file will also be write only (like the one
in eeepc-laptop).
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Asus took the DSDT from another model (L84F), made some change
to make it work, but forgot to remove WLED method (the laptop
doesn't have a wireless card). They even didn't change the model
name.
ref: https://bugzilla.kernel.org/show_bug.cgi?id=25712
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This key should power off the backlight, not the display,
it is also used in acpi/video.c to do the same thing.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
I checked some more DSDT, and it seems that I wasn't
totally right about the meaning of DSTS return value.
Bit 0 is clearly the status of the device, and I discovered
that bit 16 is set when the device is present.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Joe Perches
Roland Dreier
Linus Torvalds
Rafi Rubin
Matthew Garrett
Mattia Dongili
Manoj Iyer
Dave Airlie
Keith Packard
Lee, Chun-Yi
Marco Chiappero
Michal Marek
Alberto Mardegan
Greg Kroah-Hartman
Thomas Gleixner
Randy Dunlap
Corentin Chary
Thomas Renninger
Lucas De Marchi
Jesse Barnes
Lucas De Marchi
Dan Carpenter
Axel Lin
Joey Lee
Pali Rohár
Keng-Yu Lin
Ike Panhc
Corentin Chary
Durgadoss R
Anssi Hannula
Colin Ian King
Hong Liu