[ Upstream commit d1baf7a3a3 ]
Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220519233334.438621-1-dev_public@wujek.eu
Fixes: 75d2b2b06b ("hwmon: (pmbus) disable PEC if not enabled")
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
[groeck: Added Fixes: tags, dropped continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75d2b2b06b upstream.
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220420145059.431061-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5436af598 ]
If there is an input undervoltage fault, reported in STATUS_INPUT
command response, there is quite likely a "Unit Off For Insufficient
Input Voltage" condition as well.
Add a constant for bit 3 of STATUS_INPUT. Update the Vin limit
attributes to include both bits in the mask for clearing faults.
If an input undervoltage fault occurs, causing a unit off for
insufficient input voltage, but the unit is off bit is not cleared, the
STATUS_WORD will not be updated to clear the input fault condition.
Including the unit is off bit (bit 3) allows for the input fault
condition to completely clear.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20220317232123.2103592-1-bjwyman@gmail.com
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
[groeck: Dropped unnecessary ()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 686d303ee6 ]
On PMBUS devices with multiple pages, the regulator ops need to be
protected with the update mutex. This prevents accidentally changing
the page in a separate thread while operating on the PMBUS_OPERATION
register.
Tested on Infineon xdpe11280 while a separate thread polls for sensor
data.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/b991506bcbf665f7af185945f70bf9d5cf04637c.1645804976.git.sylv@sylv.io
Fixes: ddbb4db4ce ("hwmon: (pmbus) Add regulator support")
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35f165f089 ]
Almost all fault/warning bits in pmbus status registers remain set even
after fault/warning condition are removed. As per pmbus specification
these faults must be cleared by user.
Modify hwmon behavior to clear fault/warning bit after fetching data if
fault/warning bit was set. This allows to get fresh data in next read.
Signed-off-by: Vikash Chandola <vikash.chandola@linux.intel.com>
Link: https://lore.kernel.org/r/20220222131253.2426834-1-vikash.chandola@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7931a7b0e ]
Maintaining this manually is error prone (there are currently only
five chips supported, not six); gcc can do it for us automatically.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 666c14906b ("hwmon: (pmbus/lm25066) Drop support for LM25063")
Link: https://lore.kernel.org/r/20210928092242.30036-5-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ae59dc455a upstream.
With the exception of the lm5066i, all the devices handled by this
driver had been missing their offset ('b') coefficients for direct
format readings.
Cc: stable@vger.kernel.org
Fixes: 58615a94f6 ("hwmon: (pmbus/lm25066) Add support for LM25056")
Fixes: e53e6497fc ("hwmon: (pmbus/lm25066) Refactor device specific coefficients")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missed attribute for reading POUT from page 1.
It is supported by device, but has been missed in initial commit.
Fixes: 2c6fcbb211 ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927070740.2149290-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Tested:
Witherspoon before: 3148. Witherspoon after: 3148.
Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
BPD-RS600 modules running firmware v5.70 misreport the MFR_PIN_MAX.
The indicate a maximum of 1640W instead of 700W. Detect the invalid
reading and return a sensible value instead.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210812014000.26293-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In the initial implementation a number of PMBUS_x_WARN_LIMITs were
mapped to MFR fields. This was incorrect as these MFR limits reflect the
rated limit as opposed to a limit which will generate warning. Instead
return -ENXIO like we were already doing for other WARN_LIMITs.
Subsequently these rated limits have been exposed generically as new
fields in the sysfs ABI so the values are still available.
Fixes: 15b2703e5e ("hwmon: (pmbus) Add driver for BluTek BPA-RS600")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210812014000.26293-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When doing a PMBus write for the LED control on the IBM Common Form
Factor Power Supplies (ibm-cffps), the DAh command requires that bit 7
be low and bit 6 be high in order to indicate that you are truly
attempting to do a write.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210806225131.1808759-1-bjwyman@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPD-RS600 is the DC version of the BPA-RS600. The PMBUS interface is
the same between the two models. Keep the same compatible string but
accept either BPA-RS600 or BPD-RS600 in the PMBUS_MFR_MODEL.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210708220618.23576-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The debugfs_create_dir() function returns error pointers, it doesn't
return NULL. But debugfs functions don't need to be checked in normal
situations and we can just delete this code.
Fixes: 1f442e213ce5 ("hwmon: (pmbus) Add driver for Delta DPS-920AB PSU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YMyjmR54ErLtc1sH@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds support for the Delta DPS-920AB PSU.
Only missing feature is fan control which the PSU supports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210607103431.2039073-1-robert.marko@sartura.hr
[groeck: Add MODULE_IMPORT_NS(PMBUS);]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for Flex power interface modules PIM4006,
PIM4328 and PIM4820.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow the use of a phase function even if it does not exist on
the associated page.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading and decoding direct format coefficients to
the PMBus core driver. If the new flag PMBUS_USE_COEFFICIENTS_CMD
is set, the driver will use the COEFFICIENTS register together with
the information in the pmbus_sensor_attr structs to initialize
relevant coefficients for the direct mode format.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
[groeck: Initialize ret with -EINVAL in pmbus_init_coefficients()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips respond with invalid data when reading the WRITE_PROTECT
register. For such chips, this flag should be set so that the PMBus core
driver doesn't use the WRITE_PROTECT command to determine its behavior.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, for Packet Error Checking (PEC) only the controller
is checked for support. This causes problems on the cisco-8000
platform where a SMBUS transaction errors are observed. This is
because PEC has to be enabled only if both controller and
adapter support it.
Added code to check PEC capability for adapter and enable it
only if both controller and adapter supports PEC.
Signed-off-by: Madhava Reddy Siddareddygari <msiddare@cisco.com>
[Upstream from SONiC https://github.com/Azure/sonic-linux-kernel/pull/215]
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20210605052700.541455-1-pmenzel@molgen.mpg.de
[groeck: Dropped unnecessary continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
adm1272 supports temperature reporting but it is disabled by default.
Tested:
ls temp1_*
temp1_crit temp1_highest temp1_max
temp1_crit_alarm temp1_input temp1_max_alarm
cat temp1_input
26642
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20210512171043.2433694-1-linchuyuan@google.com
[groeck: Updated subject to reflect correct driver]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a digital, multi-phase, pulse-width modulation
controller.
This device supports:
- One power rail.
- Programmable Multi-Phase up to 10 Phases.
- PWM-VID Interface
- One pages 0 for telemetry.
- Programmable pins for PMBus Address.
- Built-In EEPROM to Store Custom Configurations.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210511055619.118104-3-vadimp@nvidia.com
[groeck: Add MODULE_IMPORT_NS]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Increase maximum number of phases from 8 to 10 to support multi-phase
devices allowing up to 10 phases.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210511055619.118104-2-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Flex BMR310, BMR456, BMR457, BMR458, BMR480, BMR490,
BMR491 and BMR492 to the pmbus driver
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-4-erik.rosen@metormote.com
[groeck: Fixed minor whitespace error]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips end up in an undefined state when trying to read an
unsupported register. For such chips, it is necessary to reset the
chip pmbus controller to a known state after a failed register check.
This can be done by reading a known register. By setting this flag the
driver will try to read the STATUS register after each failed
register check. This read may fail, but it will put the chip into a
known state.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-2-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Renesas ZL8802 Dual Channel/Dual Phase PMBus DC/DC
Digital Controller as well as ZLS1003 and ZLS4009 custom DC/DC
controller chips.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210423153329.33457-2-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPA-RS600 doesn't follow the PMBus spec for linear data.
Specifically it treats the mantissa as an unsigned 11-bit value instead
of a two's complement 11-bit value. At this point it's unclear whether
this only affects Vin or if Pin/Pout1 are affected as well. Erring on
the side of caution only Vin is dealt with here.
Fixes: 15b2703e5e ("hwmon: (pmbus) Add driver for BluTek BPA-RS600")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210616034218.25821-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PMBUS_MFR_ID block is actually 6 chars for q54sj108a2.
/sys/bus/i2c/drivers/q54sj108a2_test# iotools smbus_read8 $BUS $ADDR 0x99
0x06
Tested: Devices are able to bind to the q54sj108a2 driver successfully.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20210517222606.3457594-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The initial version of the RAA228228 datasheet claimed that the device
supported READ_TEMPERATURE_3 but not READ_TEMPERATURE_1. It has since been
discovered that the datasheet was incorrect. The RAA228228 does support
READ_TEMPERATURE_1 but does not support READ_TEMPERATURE_3.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Fixes: 51fb91ed5a ("hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228")
Link: https://lore.kernel.org/r/20210514211954.GA24646@raspberrypi
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After testing new YH-5151E devices, we found out that not all YH-5151E
work the same. The newly tested devices actually report vout correctly
in linear16 (even though they're still YH-5151E). We suspect that it is
because these new devices have a different firmware version, but that is
unconfirmed. The version cannot be queried through PMBus.
The compliant versions of YH-5151E report VOUT_MODE normally, so we turn
on the linear11 workaround only if VOUT_MODE doesn't report anything.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210513201110.313523-1-kubernat@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I didn't properly test the driver for YH-5151E, so it was completely
broken. Firstly, the log/real mapping was incorrect in one case.
Secondly, PMBus specifies that output voltages should be in the linear16
encoding. However, the YH-5151E is non-compliant and uses linear11.
YM-2151E isn't affected by this. Fix this by converting the values
inside the read functions. linear16 gets the exponent from the VOUT_MODE
command. The device doesn't support it, so I have to manually supply the
value for it.
Both supported devices have now been tested to report correct vout
values.
Fixes: 1734b4135a ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210429075337.110502-1-kubernat@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Exported pmbus symbols are only supposed to be used from PMBus code.
Introduce PMBUS symbol namespace to prevent misuse from other code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus driver support for Maxim MAX15301 InTune Automatically
Compensated Digital PoL Controller with Driver and PMBus Telemetry
Even though the specification does not specifically mention it,
extensive empirical testing has revealed that auto-detection of
limit-registers will fail in a random fashion unless the delay
parameter is set to above about 80us. The default delay is set
to 100us to include some safety margin.
This patch is tested on a Flex BMR461 converter module.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210419101251.24840-1-erik.rosen@metormote.com
[groeck: Added rationale for delay to driver header]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Certain VRs might be configured to use only the first output channel and
so the mode for the second will be 0. Handle this gracefully.
Fixes: b9fa0a3acf ("hwmon: (pmbus/core) Add support for vid mode detection per page bases")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210416102926.13614-1-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for these devices:
- YH-5151E - the PDU
- YM-2151E - the PSU
The device datasheet says that the devices support PMBus 1.2, but in my
testing, a lot of the commands aren't supported and if they are, they
sometimes behave strangely or inconsistently. For example, writes to the
PAGE command requires using PEC, otherwise the write won't work and the
page won't switch, even though, the standard says that PEC is optional.
On the other hand, writes to SMBALERT don't require PEC. Because of
this, the driver is mostly reverse engineered with the help of a tool
called pmbus_peek written by David Brownell (and later adopted by my
colleague Jan Kundrát).
The device also has some sort of a timing issue when switching pages,
which is explained further in the code.
Because of this, the driver support is limited. It exposes only the
values that have been tested to work correctly.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210414080019.3530794-1-kubernat@cesnet.cz
[groeck: Fixed up "missing braces around initializer" from 0-day]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for TI TPS53676 controller to the tps53679 pmbus driver
The driver uses the USER_DATA_03 register to figure out how many phases
are enabled and to which channel they are assigned, and sets the number
of pages and phases accordingly.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210322193734.75127-3-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPA-RS600 is a compact 600W AC to DC removable power supply module.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210317040231.21490-3-chris.packham@alliedtelesis.co.nz
[groeck: Added bpa-rs600 to index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
coccicheck complains about the use of snprintf() in sysfs
show functions.
drivers/hwmon/ina3221.c:701:8-16: WARNING: use scnprintf or sprintf
This results in a large number of patch submissions. Fix it all in
one go using the following coccinelle rules. Use sysfs_emit instead
of scnprintf or sprintf since that makes more sense.
@depends on patch@
identifier show, dev, attr, buf;
@@
ssize_t show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
return
- snprintf(buf, \( PAGE_SIZE \| PAGE_SIZE - 1 \),
+ sysfs_emit(buf,
...);
...>
}
@depends on patch@
identifier show, dev, attr, buf, rc;
@@
ssize_t show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
rc =
- snprintf(buf, \( PAGE_SIZE \| PAGE_SIZE - 1 \),
+ sysfs_emit(buf,
...);
...>
}
While at it, remove unnecessary braces and as well as unnecessary
else after return statements to address checkpatch warnings in the
resulting patch.
Cc: Zihao Tang <tangzihao1@hisilicon.com>
Cc: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon sysfs ABI requires that the `name` property doesn't include
any dashes. But when the pmbus code picks the name up from the device
tree it quite often does. Replace '-' with '_' before registering the
device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210317040231.21490-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for ST STPDDC60 Unversal Digital
Multicell Controller.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-3-erik.rosen@metormote.com
[groeck: Fixed whitespace error in Makefile]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For the STPDDC60 chip, the vout alarm-limits are represented as an offset
relative to the commanded output voltage. This means that the limits are
dynamic and must not be cached by the pmbus driver. This patch adds a
pmbus_set_sensor() function to pmbus_core to be able to set the update flag
on selected sensors after auto-detection of limit attributes.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-2-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There was an issue in how the tach feedbacks of dual rotor fans were
reported during any change in fan speeds with revision "A" of the
MAX31785. When the fan speeds would transition to a new target speed,
the rotor not wired to the TACH input when TACHSEL = 0 would report a
speed of 0 until the new target was reached. This has been fixed,
resulting in a revision "B" update where the MFR_REVISION of "B" is
0x3061.
Signed-off-by: Matthew Barth <msbarth@linux.ibm.com>
Link: https://lore.kernel.org/r/20210201212217.73721-1-msbarth@linux.ibm.com
[groeck: Change 'ret' variable type to int]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16508 is quite similar to MAX16601, except that it does not support
the DEFAULT_NUM_POP register and we thus can not dynamically determine
the number of populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-2-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX16601 can report the number of populated phases. Use this
information to only create sysfs attributes for populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-1-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix the following coccicheck warnings:
./drivers/hwmon/pmbus/pmbus_core.c:1265:24-26: WARNING !A || A && B is
equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1611642100-29937-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several power supplies supported by the IBM CFFPS driver don't
report valid data in the CAPABILITY register. This results in PEC
being enabled when it's not supported by the device, and since
the automatic version detection might fail, disable use of the
CAPABILITY register across the board for this driver.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20201222152640.27749-3-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips don't respond with valid data when reading the
CAPABILITY register. Add a flag that device drivers can set so
that the PMBus core driver doesn't use CAPABILITY to determine it's
behavior.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20201222152640.27749-2-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adam Wujek
Brandon Wyman
Patrick Rudolph
Vikash Chandola
Zev Weiss
Vadim Pasternak
Chris Packham
Dan Carpenter
Robert Marko
Erik Rosen
Madhava Reddy Siddareddygari
Chu Lin
Grant Peltier
Václav Kubernát
Guenter Roeck
Paul Fertser
Matthew Barth
Jiapeng Zhong
Eddie James