Add support for variable-length, extended, and vendor specific
CDBs to scsi-ml. It is now possible for initiators and ULD's
to issue these types of commands. LLDs need not change much.
All they need is to raise the .max_cmd_len to the longest command
they support (see iscsi patch).
- clean-up some code paths that did not expect commands to be
larger than 16, and change cmd_len members' type to short as
char is not enough.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- struct scsi_cmnd had a 16 bytes command buffer of its own.
This is an unnecessary duplication and copy of request's
cmd. It is probably left overs from the time that scsi_cmnd
could function without a request attached. So clean that up.
- Once above is done, few places, apart from scsi-ml, needed
adjustments due to changing the data type of scsi_cmnd->cmnd.
- Lots of drivers still use MAX_COMMAND_SIZE. So I have left
that #define but equate it to BLK_MAX_CDB. The way I see it
and is reflected in the patch below is.
MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
as per the SCSI standard and is not related
to the implementation.
BLK_MAX_CDB. - The allocated space at the request level
- I have audit all ISA drivers and made sure none use ->cmnd in a DMA
Operation. Same audit was done by Andi Kleen.
(*)fixed-length here means commands that their size can be determined
by their opcode and the CDB does not carry a length specifier, (unlike
the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
true and the SCSI standard also defines extended commands and
vendor specific commands that can be bigger than 16 bytes. The kernel
will support these using the same infrastructure used for VARLEN CDB's.
So in effect MAX_COMMAND_SIZE means the maximum size command
scsi-ml supports without specifying a cmd_len by ULD's
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Count FMR alignment violations per session as part of the iscsi
statistics.
Signed-off-by: Eli Dorfman <elid@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current target allocation code registeres each possible target
with sysfs; it will be deleted again if no useable LUN on this target
was found. This results in a string of 'target add/target remove' uevents.
Based on a patch by Hannes Reinecke <hare@suse.de> this patch reworks
the target allocation code so that only uevents for existing targets
are sent. The sysfs registration is split off from the existing
scsi_target_alloc() into a in a new scsi_add_target() function, which
should be called whenever an existing target is found. Only then a
uevent is sent, so we'll be generating events for existing targets
only.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they (or some user of them) rely
on it dragging in some unrelated header file, but I can't build all
these files, so we'll have to fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Support for extended CDBs in iscsi.
All we need is to check if command spills over 16 bytes then allocate
an iscsi-extended-header for the leftovers.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Two functions in include/scsi/sas_ata.h don't have static inlines
leading to problems if they're built in:
On Thu, 2008-04-03 at 14:06 +0200, Toralf Förster wrote:
> drivers/scsi/mvsas.o: In function `sas_ata_init_host_and_port':
> mvsas.c:(.text+0x0): multiple definition of `sas_ata_init_host_and_port'
> drivers/scsi/libsas/built-in.o:(.text+0x37f4): first defined here
> drivers/scsi/mvsas.o: In function `sas_ata_task_abort':
> mvsas.c:(.text+0x7): multiple definition of `sas_ata_task_abort'
> drivers/scsi/libsas/built-in.o:(.text+0x37fb): first defined here
> make[2]: *** [drivers/scsi/built-in.o] Error 1
> make[1]: *** [drivers/scsi] Error 2
> make: *** [drivers] Error 2
Add the correct static inline modifiers.
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds scsi_build_sense_buffer, a simple helper function to build
sense data in a buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by things like USB storage that want to set up static
commands for later use at start of day.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
LLDs need to copies data between the SG table in struct scsi_cmnd and
liner buffer. So they use the helper functions like
sg_copy_from_buffer(scsi_sglist(sc), scsi_sg_count(sc), buf, buflen)
sg_copy_to_buffer(scsi_sglist(sc), scsi_sg_count(sc), buf, buflen)
This patch just adds wrapper functions:
scsi_sg_copy_from_buffer(sc, buf, buflen)
scsi_sg_copy_to_buffer(sc, buf, buflen)
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The problem is that serveral drivers are sending a target reset from the
device reset handler, and if we have multiple devices a target reset gets
sent for each device when only one would be sufficient. And if we do a target
reset it affects all the commands on the target so the device reset handler
code only cleaning up one devices's commands makes programming the driver a
little more difficult than it should be.
This patch adds a target reset handler, which drivers can use to send
a target reset. If successful it cleans up the commands for a devices
accessed through that starget.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Provide a facility to use the request_firmware() interface to get a SAS
address from userspace. This can be used by SAS LLDDs that cannot
obtain the address from the host adapter.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For qla4xxx, we could be starting a session, but some error (network,
target, IO from a device that got started, etc) could cause the session
to fail and curring the block/unblock and state manipulation could race
with each other. This patch just has those operations done in the
single threaded iscsi eh work queue, so that way they are serialized.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by the to be added I_T reset function in aic94xx. It
needs to know the local phy so it can send a link or hard reset along
the path.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since the sg chaining patches went in, our current value of 255 for
SG_ALL excites chaining on some drivers which cannot support it (and
would thus oops). Redefine SG_ALL to mean no sg table size
preference, but use the single allocation (non chained) limit. This
also helps for drivers that use it to size an internal table.
We'll do an opt in system later where truly chaining supporting
drivers can define their sg_tablesize to be anything up to
SCSI_MAX_SG_CHAIN_ELEMENTS.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Small cleanups in scsi_host.h. Few #defines make me wonder if their
description is still up to date..?
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A lot of SCSI command replies have a protocol ID field. Add
definitions for the interpretation of that from SPC-3.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The session age mask is only 4 bits, but session->age is 32. When
it gets larger then 15 and we try to or the bits some bits get
dropped and the check for session age in iscsi_verify_itt is useless.
The ISCSI_CID_MASK related bits are also useless since cid is always
one.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some iscsi class messages have the dev_printk prefix and some libiscsi
and iscsi_tcp messages have "iscsi" or the module name as a prefix which
is normally pretty useless when trying to figure out which session
or connection the message is attached to. This patch adds iscsi lib
and class dev_printks so all messages have a common prefix that
can be used to figure out which object printed it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In qla4xxx's probe it will call the iscsi session setup functions
for session that got setup on the initial start. This then makes
it easy for the iscsi class to export a helper which indicates
when those scans are done.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This just adds iscsi session scanning which works like fc rport scanning.
The future patches will hook the drivers into Mathew Wilcox's async
scanning infrastructure, so userspace does not have to special case
iscsi and so userspace does not have to make a extra special case for
hardware iscsi root scanning.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds a iscsi session state file which exports the session
state for both software and hardware iscsi. It also hooks libiscsi
in.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
__iscsi_complete_pdu() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
At the block level bidi request uses req->next_rq pointer for a second
bidi_read request.
At Scsi-midlayer a second scsi_data_buffer structure is used for the
bidi_read part. This bidi scsi_data_buffer is put on
request->next_rq->special. Struct scsi_cmnd is not changed.
- Define scsi_bidi_cmnd() to return true if it is a bidi request and a
second sgtable was allocated.
- Define scsi_in()/scsi_out() to return the in or out scsi_data_buffer
from this command This API is to isolate users from the mechanics of
bidi.
- Define scsi_end_bidi_request() to do what scsi_end_request() does but
for a bidi request. This is necessary because bidi commands are a bit
tricky here. (See comments in body)
- scsi_release_buffers() will also release the bidi_read scsi_data_buffer
- scsi_io_completion() on bidi commands will now call
scsi_end_bidi_request() and return.
- The previous work done in scsi_init_io() is now done in a new
scsi_init_sgtable() (which is 99% identical to old scsi_init_io())
The new scsi_init_io() will call the above twice if needed also for
the bidi_read command. Only at this point is a command bidi.
- In scsi_error.c at scsi_eh_prep/restore_cmnd() make sure bidi-lld is not
confused by a get-sense command that looks like bidi. This is done
by puting NULL at request->next_rq, and restoring.
[jejb: update to sg_table and resolve conflicts
also update to blk-end-request and resolve conflicts]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In preparation for bidi we abstract all IO members of scsi_cmnd,
that will need to duplicate, into a substructure.
- Group all IO members of scsi_cmnd into a scsi_data_buffer
structure.
- Adjust accessors to new members.
- scsi_{alloc,free}_sgtable receive a scsi_data_buffer instead of
scsi_cmnd. And work on it.
- Adjust scsi_init_io() and scsi_release_buffers() for above
change.
- Fix other parts of scsi_lib/scsi.c to members migration. Use
accessors where appropriate.
- fix Documentation about scsi_cmnd in scsi_host.h
- scsi_error.c
* Changed needed members of struct scsi_eh_save.
* Careful considerations in scsi_eh_prep/restore_cmnd.
- sd.c and sr.c
* sd and sr would adjust IO size to align on device's block
size so code needs to change once we move to scsi_data_buff
implementation.
* Convert code to use scsi_for_each_sg
* Use data accessors where appropriate.
- tgt: convert libsrp to use scsi_data_buffer
- isd200: This driver still bangs on scsi_cmnd IO members,
so need changing
[jejb: rebased on top of sg_table patches fixed up conflicts
and used the synergy to eliminate use_sg and sg_count]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we export scsi_init_io()/scsi_release_buffers() instead of
scsi_{alloc,free}_sgtable() from scsi_lib than tgt code is much more
insulated from scsi_lib changes. As a bonus it will also gain bidi
capability when it comes.
[jejb: rebase on to sg_table and fix up rejections]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Also change scsi_alloc_sgtable() to just return 0/failure, since it
maps to the command passed in. ->request_buffer is now no longer needed,
once drivers are adapted to use scsi_sglist() it can be killed.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Break out the frame processor for STP tasks from aic94xx so they can
be shared by other SAS HBA's
Original patch from Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes static array sense_buffer in scsi_cmnd and uses
dynamically allocated sense_buffer (with GFP_DMA).
The reason for doing this is that some architectures need cacheline
aligned buffer for DMA:
http://lkml.org/lkml/2007/11/19/2
The problems are that scsi_eh_prep_cmnd puts scsi_cmnd::sense_buffer
to sglist and some LLDs directly DMA to scsi_cmnd::sense_buffer. It's
necessary to DMA to scsi_cmnd::sense_buffer safely. This patch solves
these issues.
__scsi_get_command allocates sense_buffer via kmem_cache_alloc and
attaches it to a scsi_cmnd so everything just work as before.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds a new scsi_device flag (last_sector_bug) for devices
which contain a bug where the device crashes when the last sector is
read in a larger then 1 sector read.
This is for example the case with sdcards in the HP PSC1350 printer
cardreader and in the HP PSC1610 printer cardreader.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is bad for two reasons:
1. If they're returned to outside applications, no-one knows what
they mean.
2. Eventually they'll clash with the ever expanding standard error
codes.
The problem error code in question is ETASK. I've replaced this by
ECOMM (communications error on send) a network error code that seems to
most closely relay what ETASK meant.
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds support for host side SMP processing, via a separate
SMP interpreter file.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert xmit to iscsi chunks.
from michaelc@cs.wisc.edu:
Bug fixes, more digest integration, sg chaining conversion and other
sg wrapper changes, coding style sync up, and removal of io fields,
like pdu_sent, that are not needed.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During root boot and shutdown the target could send us nops.
At this time iscsid cannot be running, so the target will drop
the session and the boot or shutdown will hang.
To handle this and allow us to better control when to check the network
this patch moves the nop handling to the kernel.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the device delete sysfs file to remove each device
then logout. Now in 2.6.21 this will not work because
the sysfs delete file returns immediately and does not wait for
the device removal to complete. This causes a hang if a cache sync
is needed during shutdown. Before .21, that approach had other
problems, so this patch fixes the shutdown code so that we remove the target
and unbind the session before logging out and shut down the session
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is not need to block the session during logout. Since
we are going to fail the commands that were blocked just fail them
immediately instead.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iscsi_pool_init simplified
iscsi_pool_init currently has a lot of duplicate kfree() calls it does
when some allocation fails. This patch simplifies the code a little by
using iscsi_pool_free to tear down the pool in case of an error.
iscsi_pool_init also returns a copy of the item array to the caller.
Not all callers use this array, so we make it optional.
Instead of allocating a second array and return that, allocate just one
array, of twice the size.
Update users of iscsi_pool_{init,free}
This patch drops the (now useless) second argument to
iscsi_pool_free, and updates all callers.
It also removes the ctask->r2ts array, which was never
used anyway. Since the items argument to iscsi_pool_init
is now optional, we can pass NULL instead.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
at libiscsi generic code
- currently code assumes a storage space of pdu header is allocated
at llds ctask and is pointed to by iscsi_cmd_task->hdr. Here I add
a hdr_max field pertaining to that storage, and an hdr_len that
accumulates the current use of the pdu-header.
- Add an iscsi_next_hdr() inline which returns the next free space
to write new Header at. Also iscsi_next_hdr() is used to retrieve
the address at which to write the header-digest.
- Add iscsi_add_hdr(length). What the user do is calls iscsi_next_hdr()
for address of the new header, than calls iscsi_add_hdr(length) with
the size of the new header. iscsi_add_hdr() will check if space is
available and update to the new size. length must be padded according
to standard.
- Add 2 padding inline helpers thanks to Olaf. Current patch does not
use them but Following patches will.
Also moved definition of ISCSI_PAD_LEN to iscsi_proto.h which had
PAD_WORD_LEN that was never used anywhere.
- Let iscsi_prep_scsi_cmd_pdu() signal an Error return since now it is
possible that it will fail.
- I was tired of yet again writing a "this is a digest" comment next to
sizeof(__u32) so I defined a new ISCSI_DIGEST_SIZE. Now I don't need
any comments. Changed all places that used sizeof(__u32) or "4" in
connection to a digest.
iscsi_tcp specific code
- At struct iscsi_tcp_cmd_task allocate maximum space allowed in
standard for all headers following the iscsi_cmd header. and mark
it so in iscsi_tcp_session_create()
- At iscsi_send_cmd_hdr() retrieve the correct headers size and
write header digest at iscsi_next_hdr().
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rewrite recv path. Fixes:
- data digest processing and error handling.
- ahs support.
Some fixups by Mike Christie
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds logical unit reset support. This should work for ib_iser,
but I have not finished testing that driver so it is not hooked in yet.
This patch also temporarily reverts the iscsi_tcp r2t write out patch.
That code is completely rewritten in this patchset.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current scsi_test_unit_ready() is updated to return sense code
information (in struct scsi_sense_hdr). The sd and sr drivers are
changed to interpret the sense code return asc 0x3a as no media and
adjust the device status accordingly.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some SCSI tape medium changers that need the BLIST_SINGLELUN flag have
the medium changer at one LUN and the tape drive at a different LUN.
The inquiry string of the tape drive may be different from that of the
medium changer. In order for single_lun to be effective, every
scsi_device under a given scsi_target must have it set. This means that
there needs to be a blacklist entry for BOTH the medium changer AND the
tape drive, which is impractical because some medium changers may be
paired with a variety of different tape drive models. It makes more
sense to put the single_lun flag in scsi_target instead of scsi_device,
which causes every device at a given target ID to inherit the single_lun
flag from one LUN. This makes it possible to blacklist just the medium
changer and not the tape drive.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Annotate sas_queuecommand with locking details, and clean up a few
more sparse warnings about static/non-static declarations.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sparse complains about the mixing of enums in libsas. Since the
underlying numeric values of both enums are the same, combine them
to get rid of the warning.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This will send for a card reader slot (remove/add media):
UEVENT[1187091572.155884] change /devices/pci0000:00/0000:00:1d.7/usb5/5-2/5-2:1.0/host7/target7:0:0/7:0:0:0 (scsi)
UEVENT[1187091572.162314] remove /block/sdb/sdb1 (block)
UEVENT[1187091572.172464] add /block/sdb/sdb1 (block)
UEVENT[1187091572.175408] change /devices/pci0000:00/0000:00:1d.7/usb5/5-2/5-2:1.0/host7/target7:0:0/7:0:0:0 (scsi)
and for a DVD drive (add/eject media):
UEVENT[1187091590.189159] change /devices/pci0000:00/0000:00:1f.1/host4/target4:0:0/4:0:0:0 (scsi)
UEVENT[1187091590.957124] add /module/isofs (module)
UEVENT[1187091604.468207] change /devices/pci0000:00/0000:00:1f.1/host4/target4:0:0/4:0:0:0 (scsi)
Userspace gets events, even for unpartitioned media. This unifies
the event handling for asynchronoous events (AN) and events caused by
perodical polling the device from userspace.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
[jejb: modified for new event API]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit ac40532ef0, which gets
us back the original cleanup of 6f5391c283.
It turns out that the bug that was triggered by that commit was
apparently not actually triggered by that commit at all, and just the
testing conditions had changed enough to make it appear to be due to it.
The real problem seems to have been found by Peter Osterlund:
"pktcdvd sets it [block device size] when opening the /dev/pktcdvd
device, but when the drive is later opened as /dev/scd0, there is
nothing that sets it back. (Btw, 40944 is possible if the disk is a
CDRW that was formatted with "cdrwtool -m 10236".)
The problem is that pktcdvd opens the cd device in non-blocking mode
when pktsetup is run, and doesn't close it again until pktsetup -d is
run. The effect is that if you meanwhile open the cd device,
blkdev.c:do_open() doesn't call bd_set_size() because
bdev->bd_openers is non-zero."
In particular, to repeat the bug (regardless of whether commit
6f5391c283 is applied or not):
" 1. Start with an empty drive.
2. pktsetup 0 /dev/scd0
3. Insert a CD containing an isofs filesystem.
4. mount /dev/pktcdvd/0 /mnt/tmp
5. umount /mnt/tmp
6. Press the eject button.
7. Insert a DVD containing a non-writable filesystem.
8. mount /dev/scd0 /mnt/tmp
9. find /mnt/tmp -type f -print0 | xargs -0 sha1sum >/dev/null
10. If the DVD contains data beyond the physical size of a CD, you
get I/O errors in the terminal, and dmesg reports lots of
"attempt to access beyond end of device" errors."
which in turn is because the nested open after the media change won't
cause the size to be set properly (because the original open still holds
the block device, and we only do the bd_set_size() when we don't have
other people holding the device open).
The proper fix for that is probably to just do something like
bdev->bd_inode->i_size = (loff_t)get_capacity(disk)<<9;
in fs/block_dev.c:do_open() even for the cases where we're not the
original opener (but *not* call bd_set_size(), since that will also
change the block size of the device).
Cc: Peter Osterlund <petero2@telia.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 6f5391c283 ("[SCSI]
Get rid of scsi_cmnd->done") that was supposed to be a cleanup commit,
but apparently it causes regressions:
Bug 9370 - v2.6.24-rc2-409-g9418d5d: attempt to access beyond end of device
http://bugzilla.kernel.org/show_bug.cgi?id=9370
this patch should be reintroduced in a more split-up form to make
testing of it easier.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The esp_reset_cleanup() function is called with the host lock held and
invokes starget_for_each_device() which wants to take it too. Here is a
fix along the lines of shost_for_each_device()/__shost_for_each_device()
adding a __starget_for_each_device() counterpart which assumes the lock
has already been taken.
Eventually, I think the driver should get modified so that more work is
done as a softirq rather than in the interrupt context, but for now it
fixes a bug that causes the spinlock debugger to fire.
While at it, it fixes a small number of cosmetic problems with
starget_for_each_device() too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Spotted by Paul Jackson <pj@sgi.com>
The error handler rework moved the scatterlist into a globally exposed
structure in scsi_eh.h; unfortunately, the scatterlist include needs
to move from scsi_error.c to scsi_eh.h to allow this to compile
universally.
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
/usr/include/scsi is provided by glibc.
Remove the scsi export from make headers_install target.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is what enables large commands. If we need to allocate an
sgtable that doesn't fit in a single page, allocate several
SCSI_MAX_SG_SEGMENTS sized tables and chain them together.
SCSI defaults to large chained sg tables, if the arch supports it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Just pass in the command, no point in passing in the scatterlist
and scatterlist pool index seperately.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts the SCSI mid layer to using the sg helpers for looking up
sg elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
- Drivers/transports that want to send a synchronous REQUEST_SENSE command
as part of their .queuecommand sequence, have 2 new API's that facilitate
in doing so and abstract them from scsi-ml internals.
void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd,
struct scsi_eh_save *sesci, unsigned char *cmnd,
int cmnd_size, int sense_bytes)
Will hijack a command and prepare it for request sense if needed.
And will save any later needed info into a scsi_eh_save structure.
void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd,
struct scsi_eh_save *sesci);
Will undo any changes done to a command by above function. Making
it ready for completion.
- Re-factor scsi_send_eh_cmnd() to use above APIs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi/scsi_transport_iscsi.h uses struct mutex and struct list_head,
so while linux/mutex.h and linux/list.h seem to be pulled in indirectly
by one of the headers it includes, the right thing
is to include linux/mutex.h and linus/list.h directly.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ULD ->done callback moves into the scsi_driver. By moving the call
to scsi_io_completion() from scsi_blk_pc_done() to scsi_finish_command(),
we can eliminate the latter entirely. By returning 'good_bytes' from
the ->done callback (rather than invoking scsi_io_completion()), we can
stop exporting scsi_io_completion().
Also move the prototypes from sd.h to sd.c as they're all internal anyway.
Rename sd_rw_intr to sd_done and rw_intr to sr_done.
Inspired-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Because scsi_print_sense_hdr prefixes with KERN_INFO, the output from
scsi_io_completion looks like:
sd 0:0:0:0: [sdb] Device not ready: <6>: Sense Key : 0x2 [current]
: ASC=0x4 ASCQ=0x3
By using scsi_show_sense_hdr, we can get the much more appealing output:
sd 0:0:0:0: [sdb] Device not ready: Sense Key : 0x2 [current]
sd 0:0:0:0: [sdb] Device not ready: ASC=0x4 ASCQ=0x3
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The pid field is a duplicate of the serial_number field and has been
scheduled for removal for a long time. A few drivers were still using
it, so just change them to use serial_number instead.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the intents of the block prep function was to allow ULDs to use
it for preprocessing. The original SCSI model was to have a single prep
function and add a pointer indirect filter to build the necessary
commands. This patch reverses that, does away with the init_command
field of the scsi_driver structure and makes ULDs attach directly to the
prep function instead. The value is really that it allows us to begin
to separate the ULDs from the SCSI mid layer (as long as they don't use
any core functions---which is hard at the moment---a ULD doesn't even
need SCSI to bind).
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support like the srp transport does:
- fc_remote_port_{rolechg,delete} calls
scsi_tgt_it_nexus_{create,destroy} for target drivers.
- add callbacks to notify target drivers of the nexus and tmf
operation results to fc_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds supported_mode and active_mode attributes to
/sys/class/sys_host/hostX/ for specifying the mode that a lld supports
and the currently activated mode. The output format is similar to fc
rport roles:
luce:/sys/class/scsi_host/host0$ cat supported_mode
Initiator
luce:/sys/class/scsi_host/host0$ cat active_mode
Initiator
The mode values uses bitmap since we would support dual-mode llds in
the future like this:
luce:/sys/class/scsi_host/host0$ cat supported_mode
Initiator, Target
The supported_mode attribute looks at a scsi_host_template and the
active_mode attribute looks at a scsi_host. We would add a hook to a
scsi_host_template to change the active_mode attribute
dynamically. But now there is no hook since no lld supports that
feature.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This change has already been discussed on linux-scsi:
http://marc.info/?t=118771096400003http://marc.info/?t=118760913100005
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves tsk_mgmt_response callback in struct scsi_host_template to
struct scsi_transport_template since struct scsi_transport_template is
more suitable for the task management stuff.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts libsrp and ibmvstgt to use srp transport.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support:
- srp_rport_{add,del} calls scsi_tgt_it_nexus_{create,destroy} for
target drivers.
- add a callback to notify target drivers of the nexus operation
results to srp_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
tgt uses scsi_host as I_T nexus. This works for ibmvstgt because it
creates one scsi_host for one initiator. However, other target drivers
don't work like that.
This adds I_T nexus support, which enable one scsi_host to handle
multiple initiators. New scsi_tgt_it_nexus_create/destroy functions
are expected be called transport classes. For example, ibmvstgt
creates an initiator remote port, then the srp transport calls
tgt_it_nexus_create. tgt doesn't manages I_T nexus, instead it tells
tgtd, user-space daemon, to create a new I_T nexus.
On the receiving the response from tgtd, tgt calls
shost->transportt->it_nexus_response. transports should notify a
lld. The srp transport uses it_nexus_response callback in
srp_function_template to do that.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds a 'roles' attribute to rport like transport_fc. The role can
be initiator or target. That is, the initiator driver creates target
remote ports and the target driver creates initiator remote ports.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds srp transport class that works with ib_srp and ibmvscsi.
It creates only /sys/class/{srp_host,srp_remote_ports} and
srp_remote_ports has only "port_id" attribute.
viola:/sys/class/srp_remote_ports/port-0:1# ls
device port_id subsystem uevent
viola:/sys/class/srp_remote_ports/port-0:1# cat port_id
4c:49:4e:55:58:20:56:49:4f:00:00:00:00:00:00:00
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The iscsi eh could be tearing down the session/connection while
the scsi eh is still sending task management functions. If when
we drop the session lock to grab the recv lock, the iscsi eh
tears down the connection we will oops.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Our current implementation has a generic set of barrier functions that
go through the SCSI driver model. Realistically, this is unnecessary,
because the only device that can use barriers (sd) can set the flush
functions up at probe or revalidate time. This patch pulls the barrier
functions out of the mid layer and scsi driver model and relocates them
directly in sd.
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
We should not be checking the cmd windown for just handling r2t responses.
And if the window closes in on us, always have scsi-ml requeue the command
from our queuecommand function.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Eliminate unnecessary PCI dependencies in libsas. It should use generic
DMA and struct device like other subsystems.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Not everyone wants libsas automatically to pull in libata. This patch
makes the behaviour configurable, so you can build libsas with or
without ATA support.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's currently no destructor for the bsg components. If you insert
and remove the module, you see the bsg devices building up and up. This
patch adds the destructor in the correct place in the transport class so
that the bsg and request queue are removed just before the device
destruction.
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
collapsed with fw-sbp2 patch "Drop cast to non-const char * in host
template initialization." from Kristian Høgsberg
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for SAS Management Protocol (SMP) passthrough
support via bsg. aic94xx can use this.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The sas transport class attaches one bsg device to every SAS object
(host, device, expander, etc). LLDs can define a function to handle
SMP requests via sas_function_template::smp_handler.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one was noticed by Gilbert Wu of Adaptec:
The libata core actually does the DMA mapping for you, so there has to
be an exception in the device drivers that *don't* do dma mapping for
ATA commands. However, since we've already done this, libsas must now
dma map any ATA commands that it wishes to issue ... and yes, this is a
horrible mess.
Additionally, the test in aic94xx for ATA protocols isn't quite right.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ATA devices need special handling for sas_task_abort. If the ATA command
came from SCSI, then we merely need to tell SCSI to abort the scsi_cmnd.
However, internal commands require a bit more work--we need to fill the qc
with the appropriate error status and complete the command, and eventually
post_internal will issue the actual ABORT TASK.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a respin of my earlier patch that migrates the ATA support code
into a separate file. For now, the controversial linking bits have
been removed per James Bottomley's request for a patch that contains
only the migration diffs, which means that libsas continues to require
libata. I intend to address that problem in a separate patch.
This patch is against the aic94xx-sas-2.6 git tree, and it has been
sanity tested on my x206m with Seagate SATA and SAS disks without
uncovering any new problems.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hook the scsi_host_template functions in libsas to delegate
functionality to libata when appropriate.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Misc code changes and merge fixes and update for libata->drivers/ata
move
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removes an obsolete method scsi_device_cancel which isn't being used
anywhere in the kernel.
Signed-off-by: Priyanka Gupta <priyankag@google.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When reporting SCSI devices to the SCSI midlayer, use the FCP LUN as
LUN reported to the SCSI layer. With this approach, zfcp does not have
to create unique LUNS, and this code can be removed.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch exports the local address for the session. For
qla4xxx this is the ip of the hba's port. For software
this is the src addr of the socket.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Userspace will want to know what the driver/FW/HW capabilites
when it comes to some operations like if the hardware can
do discovery or if it can store iscsi info like what target
was used for boot. This patch adds some new caps so userspace
can tell if the driver supports hardware/fw based sendtargets
discovery and if the hardware has some flash which may be
holding or can contain some iscsi target info
.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Boaz Harrosh
Eli Dorfman
James Bottomley
Linus Torvalds
Tony Jones
Matthew Wilcox
FUJITA Tomonori
Mike Christie
Darrick J. Wong
Pavel Machek
Adrian Bunk
Joe Perches
FUJITA Tomonori
Jens Axboe
Hans de Goede
Olaf Kirch
James Bottomley
Tony Battersby
Kay Sievers
Linus Torvalds
Ingo Molnar
Maciej W. Rozycki
Jeff Garzik
Olaf Hering
Michael S. Tsirkin
Christof Schmitt
Kristian Høgsberg
Priyanka Gupta