The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmB1XbkACgkQJWrqGEe9
VoSWEAf6Al9DFds3w32oS8OB19pMb66jWLPvt//gIwV4tzSIsauQLqo4uBqDUPSt
EdUyehN6W792qsekmOReRc4ZcS2HpNPT5PRwYtsxPMkVmEL56tqs5ObNPGNOwvoH
9vyvsx7EhSu10a9JHjgJeNMVOBDMA8quXqHw0Y3cL2UBpuCYMm37ANF8okdvOmmr
Ykg1nCbfZL/dxFCGZ15ZuYuGQXea8PUryyxXUsWLDvsHg4KuhQKKtkarXmzz6XiD
tAyShtSrJFo/T0FniWc8jFbaq8WkU7XBg5f5qTTt5uT4JoXWGmjbIbXG0My91RKY
RO0b6z/odPOW1UHarlK8HrKW22YF9A==
=+fKJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
SPI NOR controller drivers changes:
- intel-spi: Move platform data header to x86 subfolder
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmByqyYACgkQS1VPR6WN
FOkkYwgAvjQoUPZ/ZzwKbAuEseVB4DWj0goyTNNjksw5oIDmxcfDDd4gFTyRvLmb
eyYMGCqnBSq9asbmzWu6H5IYWllsWgRvHuRlfKlJPj6Iqc+kAv8zaezQcY5t9lYy
EopogLmc3RJdHdV3FbiRYqebATCCfwkQzDJdp7QU3EdKzQp+6AmJdClssKsxkXsm
mUHmrhRF7K4jloaKfsbDwvM7DHPyhJEP/AyuDRactZzoQLhrTB/5rJ3nwpQ3k0x6
EZ53Qx08Qk9lhzR7trYOaltoTtOVc9wiIz+QGuLXfleBEfi7hRBvscx2FZKL4GwI
O2Fsg4of06KKTJ3LiOuiHykXFZ+GUA==
=/6EZ
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
SPI NOR controller drivers changes:
- intel-spi: Move platform data header to x86 subfolder
Just a couple of fixes for v5.13-rc1
* Disable broken buffered writes for CFI chips within ID 0x2201
* Address a Coverity report for unused value
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAmB10GgQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW40OcCADGpa4hnu3vWIkgwHGOFhW6YtsDTZ5A8LSw
T0eSdEets7No8p1E0HjOb623qcqm7WMfgYBkRFHLqbcl/BYZ4IUQscBh+5iP28Lf
i+AJdnxdryYZLNIiympwhSbvg9zRkGY6Abi2OVdPeEBNlb89Fo4fst5dnsc4CK8T
evQlA7P5ZeQk4DSHPGN6BfvZrej7nVczdmB1srpt9pxKWdwWGmEQoj+d1zOcYe0j
ziTcSBNbkGqLZ0agtCZiE2tzFOLGcsnMc2fXk7DYdu3CL5EBu5gP+QTdk+Iftdsb
G6VvOYaLF3AsqkacbSjxdwsoyUNVSIsqO4BM0YCxS0EsphDU4qkX
=LX/U
-----END PGP SIGNATURE-----
Merge tag 'cfi/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
CFI changes
Just a couple of fixes for v5.13-rc1
* Disable broken buffered writes for CFI chips within ID 0x2201
* Address a Coverity report for unused value
This reverts commit 04b8edad26.
mx25l51245g and mx66l51235l have the same flash ID. The flash
detection returns the first entry in the flash_info array that
matches the flash ID that was read, thus for the 0xc2201a ID,
mx25l51245g was always hit, introducing a regression for
mx66l51235l.
If one wants to differentiate the flash names, a better fix would be
to differentiate between the two at run-time, depending on SFDP,
and choose the correct name from a list of flash names, depending on
the SFDP differentiator.
Fixes: 04b8edad26 ("mtd: spi-nor: macronix: Add support for mx25l51245g")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210402082031.19055-2-tudor.ambarus@microchip.com
If rmmod the driver during read or write, the driver will release the
resources which are used during read or write, so it is possible to
refer to NULL pointer.
Use the testcase "mtd_debug read /dev/mtd0 0xc00000 0x400000 dest_file &
sleep 0.5;rmmod spi_hisi_sfc_v3xx.ko", the issue can be reproduced in
hisi_sfc_v3xx driver.
To avoid the issue, fill the interface _get_device and _put_device of
mtd_info to grab the reference to the spi controller driver module, so
the request of rmmod the driver is rejected before read/write is finished.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1617262486-4223-1-git-send-email-yangyicong@hisilicon.com
The variable timeo is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210325174514.486272-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Buffer writes do not work with AMD chip 0x2201. The chip in question
is a AMD/Spansion/Cypress Semiconductor S29GL256N and datasheet [1]
talks about writing buffers being possible. While waiting for a neater
solution resort to writing word-sized chunks only.
Without the patch kernel logs will be flooded with entries like below:
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device...
done.
jffs2_build_filesystem(): erasing all blocks after the end marker...
MTD do_write_buffer_wait(): software timeout, address:0x01ec000a.
jffs2: Write clean marker to block at 0x01920000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01e2000a.
jffs2: Write clean marker to block at 0x01880000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01e0000a.
jffs2: Write clean marker to block at 0x01860000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01dc000a.
jffs2: Write clean marker to block at 0x01820000 failed: -5
MTD do_write_buffer_wait(): software timeout, address:0x01da000a.
jffs2: Write clean marker to block at 0x01800000 failed: -5
...
Tested on a Buffalo wzr-hp-g300nh running kernel 5.10.16.
[1] https://www.cypress.com/file/219941/download
or https://datasheetspdf.com/pdf-file/565708/SPANSION/S29GL256N/1
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210309174859.362060-1-sandberg@mailfence.com
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9a ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).
The regions are declared using a NAND chip DT property,
"secure-regions". So let's make use of this property in the raw NAND
core and skip access to the secure regions present in a system.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-4-manivannan.sadhasivam@linaro.org
With all the helper functions in place, add OTP support for the Winbond
W25Q32JW and W25Q32FW.
Both were tested on a LS1028A SoC with a NXP FSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-4-michael@walle.cc
Use the new OTP ops to implement OTP access on Winbond flashes. Most
Winbond flashes provides up to four different OTP regions ("Security
Registers").
Winbond devices use a special opcode to read and write to the OTP
regions, just like the RDSFDP opcode. In fact, it seems that the
(undocumented) first OTP area of the newer flashes is the actual SFDP
table.
On a side note, Winbond devices also allow erasing the OTP regions as
long as the area isn't locked down.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-3-michael@walle.cc
SPI flashes sometimes have a special OTP area, which can (and is) used to
store immutable properties like board serial number or vendor assigned
network hardware addresses.
The MTD subsystem already supports accessing such areas and some (non
SPI NOR) flashes already implement support for it. It differentiates
between user and factory areas. User areas can be written by the user and
factory ones are pre-programmed and locked down by the vendor, usually
containing an "electrical serial number". This patch will only add support
for the user areas.
Lay the foundation and implement the MTD callbacks for the SPI NOR and add
necessary parameters to the flash_info structure. If a flash supports OTP
it can be added by the convenience macro OTP_INFO(). Sometimes there are
individual regions, which might have individual offsets. Therefore, it is
possible to specify the starting address of the first regions as well as
the distance between two regions (e.g. Winbond devices uses this method).
Additionally, the regions might be locked down. Once locked, no further
write access is possible.
For SPI NOR flashes the OTP area is accessed like the normal memory, e.g.
by offset addressing; except that you either have to use special read/write
commands (Winbond) or you have to enter (and exit) a specific OTP mode
(Macronix, Micron).
Thus we introduce four operations to which the MTD callbacks will be
mapped: .read(), .write(), .lock() and .is_locked(). The read and the write
ops will be given an address offset to operate on while the locking ops use
regions because locking always affects a whole region. It is up to the
flash driver to implement these ops.
Signed-off-by: Michael Walle <michael@walle.cc>
[ta: use div64_u64(), IS_ALIGNED, params->otp.org. unsigned int region,
drop comment, add rlen local variable in spi_nor_mtd_otp_lock()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-2-michael@walle.cc
It makes the core file a bit smaller and provides better separation
between the Software Write Protection features and the core logic.
All the next generic software write protection features (e.g. Individual
Block Protection) will reside in swp.c.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210322075131.45093-2-tudor.ambarus@microchip.com
The blocks containing the bad block table can become bad as well. So
make sure to skip any blocks that are marked bad when searching for the
bad block table.
Otherwise in very rare cases where two BBT blocks wear out it might
happen that an obsolete BBT is used instead of a newer available
version.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210325102337.481172-1-s.riedmueller@phytec.de
This allows extending ofpart parser with support for Linksys Northstar
devices. That support uses recently added quirks mechanism.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210312134919.7767-2-zajec5@gmail.com
Partitions that contains the nvmem-cells compatible will register
their direct subonodes as nvmem cells and the node will be treated as a
nvmem provider.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210312062830.20548-1-ansuelsmth@gmail.com
This may sound like a contradiction but some SPI-NOR flashes really
support erasing their OTP region until it is finally locked. Having the
possibility to erase an OTP region might come in handy during
development.
The ioctl argument follows the OTPLOCK style.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210303201819.2752-1-michael@walle.cc
MEMLOCK, MEMUNLOCK and OTPLOCK modify protection bits. Thus require
write permission. Depending on the hardware MEMLOCK might even be
write-once, e.g. for SPI-NOR flashes with their WP# tied to GND. OTPLOCK
is always write-once.
MEMSETBADBLOCK modifies the bad block table.
Fixes: f7e6b19bc7 ("mtd: properly check all write ioctls for permissions")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210303155735.25887-1-michael@walle.cc
The module misses MODULE_DEVICE_TABLE() for both SPI and OF ID tables
and thus never autoloads on ID matches.
Add the missing declarations.
Present since day-0 of spinand framework introduction.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210323173714.317884-1-alobakin@pm.me
Suppresses the following coccinelle warning:
drivers/mtd/nand/raw/rockchip-nand-controller.c:162:4-8: WARNING use flexible-array member instead
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210323131137.45552-1-zou_wei@huawei.com
s/legacy/default. spi_nor_info_init_params initializes some default
flash parameters and settings that can be overwritten when parsing
SFDP, or by fixup hooks. There's nothing legacy about them, they are
just some default settings, if not otherwise discovered or specified.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210315055634.17332-1-tudor.ambarus@microchip.com
spi_nor_parse_sfdp(nor, nor->params);
passes for the second argument a member within the first argument.
Drop the second argument and obtain it directly from the first,
and do it across all the children functions. This is a follow up for
'commit 69a8eed58c ("mtd: spi-nor: Don't copy self-pointing struct around")'
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210306095002.22983-4-tudor.ambarus@microchip.com
addr and len were gratuitously updated even when spi_nor_wait_till_ready()
failed. Wait for the erase cmd to complete and then advance the erase.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210306095002.22983-2-tudor.ambarus@microchip.com
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements and a return
instead of letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210305081933.GA137147@embeddedor
When platform_get_drvdata() returns NULL to info, no error return code
of physmap_flash_remove() is assigned.
To fix this bug, err is assigned with -EINVAL in this case
Fixes: 73566edf9b ("[MTD] Convert physmap to platform driver")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210308034446.3052-1-baijiaju1990@gmail.com
The sparse tool complains as follows:
drivers/mtd/parsers/ofpart_core.c:25:32: warning:
symbol 'bcm4908_partitions_quirks' was not declared. Should it be static?
This symbol is not used outside of ofpart_core.c, so this
commit marks it static.
Fixes: 457da931b608 ("mtd: parsers: ofpart: support BCM4908 fixed partitions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210304064600.3279138-1-weiyongjun1@huawei.com
Partition size and offset value are in block size units, which is the
same as 'erasesize'. But when 4K sectors are enabled erasesize is set to
4K. Bail out in that case.
Fixes: 803eb124e1 ("mtd: parsers: Add Qcom SMEM parser")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/0a2611f885b894274436ded3ca78bc0440fca74a.1614790096.git.baruch@tkos.co.il
qcom_smem_get() does not return NULL, and even if it did, the NULL
condition is usually not an error but a success condition and should
not trigger an error trace.
Let's replace IS_ERR_OR_NULL() by IS_ERR().
This fixes the following smatch warning:
drivers/mtd/parsers/qcomsmempart.c:109 parse_qcomsmem_part() warn: passing zero to 'PTR_ERR'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 803eb124e1 ("mtd: parsers: Add Qcom SMEM parser")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210303084634.12796-1-miquel.raynal@bootlin.com
Some devices use fixed partitioning with some partitions requiring some
extra logic. E.g. BCM4908 may have multiple firmware partitions but
detecting currently used one requires checking bootloader parameters.
To support such cases without duplicating a lot of code (without copying
most of the ofpart.c code) support for post-parsing callback was added.
BCM4908 support in ofpart can be enabled using config option and results
in compiling & executing a specific callback. It simply reads offset of
currently used firmware partition from the DT. Bootloader specifies it
using the "brcm_blparms" property.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210301105823.31032-1-zajec5@gmail.com
Get rid of central chrdev MTD lock, which prevents simultaneous operations
on completely independent physical MTD chips. Replace it with newly
introduced per-master mutex.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210217211845.43364-2-alexander.sverdlin@nokia.com
When recursively deleting partitions, don't acquire the masters
partition lock twice. Otherwise the process ends up in a deadlocked
state.
Fixes: 46b5889cc2 ("mtd: implement proper partition handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210217195320.893253-1-mail@david-bauer.net
Removing some boilerplate by using module_mtd_blktrans instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210213164600.409061-9-zhengdejin5@gmail.com
Tudor Ambarus
Richard Weinberger
Xiang Chen
Colin Ian King
Mauri Sandberg
Manivannan Sadhasivam
Lv Yunlong
Michael Walle
Stefan Riedmueller
Rafał Miłecki
Ansuel Smith
Alexander Lobakin
Zou Wei
Kai Stuhlemmer (ebee Engineering)
Fabio Estevam
Tian Tao
Kamal Dasu
Gustavo A. R. Silva
Jia-Ju Bai
Wei Yongjun
Baruch Siach
Miquel Raynal
Tomas Winkler
Alexander Sverdlin
David Bauer
Dejin Zheng