50 MHz is an incredibly common clock rate for SD cards to run at.
It's "high speed" mode in SD (not very fast these days, but it used to
be) or:
#define HIGH_SPEED_MAX_DTR 50000000
If we don't support this then older "high speed" cards can only run at
25 MHz or at half their normal speed. There doesn't seem to be any
reason to skip this clock rate, so add it.
Fixes: 17269568f7 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201210102234.2.I26dcc0cee374f5571d9929c9985f463773167e68@changeid
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
I would repeat the same commit message that was in commit 5e4b7e82d4
("clk: qcom: gcc-sdm845: Use floor ops for sdcc clks") but it seems
silly to do so when you could just go read that commit.
NOTE: this is actually extra terrible because we're missing the 50 MHz
rate in the table (see the next patch AKA ("clk: qcom: gcc-sc7180: Add
50 MHz clock rate for SDC2")). That means then when you run an older
SD card it'll try to clock it at 100 MHz when it's only specced to run
at 50 MHz max. As you can probably guess that doesn't work super
well.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Fixes: 17269568f7 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Link: https://lore.kernel.org/r/20201210102234.1.I096779f219625148900fc984dd0084ed1ba87c7f@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The scpi_clk_match (struct of_device_id) is referenced only with
CONFIG_OF builds thus mark it as __maybe_unused:
drivers/clk/clk-scpi.c:132:34: warning:
‘scpi_clk_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201103162435.13689-8-krzk@kernel.org
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/clk-pwm.c:139:34: warning:
‘clk_pwm_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201103162435.13689-1-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no reason to keep on using the __raw_{read,write}l() I/O
accessors in Renesas ARM driver code. Switch to using the plain
{read,write}l() I/O accessors, to have a chance that this works on
big-endian.
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201119125053.4065746-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2E (R8A774C0) CPG/MSSR
driver.
Add new clk type CLK_TYPE_GEN3_E3_RPCSRC to register rpcsrc as a fixed
clock on R-Car Gen3 E3 (and also RZ/G2E which is identical to E3 SoC),
parent and the divider is set based on the register value CPG_RPCCKCR[4:3]
which has been set prior to booting the kernel.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201116101002.5986-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car V3U clock driver defines the R and OSC clocks using R-Car Gen3
clock types. However, The R-Car V3U clock driver does not use the R-Car
Gen3 clock driver core, hence registering the R and OSC clocks fails:
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock osc: -22
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock r: -22
Fix this by introducing clock definition macros specific to R-Car V3U.
Note that rcar_r8a779a0_cpg_clk_register() already handled the related
clock types. Drop the now unneeded include of rcar-gen3-cpg.h.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201109152614.2465483-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2N (R8A774B1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2M (R8A774A1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When compiling with clang:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:21: warning: no previous prototype for function 'rcar_r8a779a0_cpg_clk_register' [-Wmissing-prototypes]
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
static
Similarly, with sparse:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:12: warning: symbol 'rcar_r8a779a0_cpg_clk_register' was not declared. Should it be static?
There are no users of rcar_r8a779a0_cpg_clk_register() outside this
file, so it should be static.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200924111808.15358-1-geert+renesas@glider.be
1. Mark PM functions of newly added clkout module as unused to silence
!CONFIG_PM warnings.
2. Initialize ChipID driver later - in arch initcall.
-----BEGIN PGP SIGNATURE-----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=VCRg
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung SoC drivers changes for v5.11, part two
1. Mark PM functions of newly added clkout module as unused to silence
!CONFIG_PM warnings.
2. Initialize ChipID driver later - in arch initcall.
* tag 'samsung-drivers-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
Link: https://lore.kernel.org/r/20201207074528.4475-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver changes for omaps for genpd for v5.11 merge window
This series of changes allows booting am335x with genpd and
device tree data without the legacy platform data. Also at
least am437x can be booted with gendp with power domain and
dts data. The SoC specific dts changes will be a separate
pull request.
We need the following driver changes merged before the dts
changes can be done:
- platform code needs a few improvments to probe l4_wkup first
for clocks, and to bail out when there is no platform data
- ti-sysc driver needs a non-urgent fix for asserting rstctrl
reset only after disabling the clocks, to probe modules with
no known control registers, and added quirk handling for gpmc
devices
- omap-prm driver needs a non-urgent fix for reset status bit,
support added for pm_clk, and then we add the rest of am335x
power domain data
- clock driver for am335x needs to keep l3_main clock enabled
with genpd for suspend and resume to work
- wkup_m3 remoteproc driver needs support added for reset
control if available instead of the legacy pdata callbacks
- pm33xx driver needs PM runtime support added for genpd
The am335x specific driver changes for the clock, wkup_m3,
pm33xx and remoteproc drivers are quite trivial and have not
caused merge conflicts in Linux next. I did not get acks for
these changes except from Santosh but had already pushed out
the branch already at that point. So I've added the related
driver maintainers to Cc.
* tag 'omap-for-v5.11/genpd-drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
remoteproc/wkup_m3: Use reset control driver if available
soc: ti: pm33xx: Enable basic PM runtime support for genpd
soc: ti: omap-prm: am3: add genpd support for remaining PRM instances
soc: ti: omap-prm: Add pm_clk for genpd
clk: ti: am33xx: Keep am3 l3 main clock always on for genpd
bus: ti-sysc: Implement GPMC debug quirk to drop platform data
bus: ti-sysc: Support modules without control registers
ARM: OMAP2+: Probe PRCM first to probe l4_wkup with simple-pm-bus
ARM: OMAP2+: Check for inited flag
bus: ti-sysc: Assert reset only after disabling clocks
soc: ti: omap-prm: Do not check rstst bit on deassert if already deasserted
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/pull-1606806458-694517@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the FlexSPI clock on Freescale Layerscape SoCs. The
clock is a simple divider based one and is located inside the device
configuration space (DCFG).
This will allow switching the SCK frequencies for the FlexSPI interface
on the LS1028A and the LX2160A.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20201108185113.31377-8-michael@walle.cc
[sboyd@kernel.org: Drop modalias, add module table]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To avoid future mistakes in the device tree for the clockgen module, add
constants for the clockgen subtype as well as a macro for the PLL
divider.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201108185113.31377-4-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Freescale QorIQ clock controller is only present on Freescale E500MC
and Layerscape SoCs. Add platform dependencies to the CLK_QORIQ config
symbol, to avoid asking the user about it when configuring a kernel
without E500MC or Layerscape support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20201110154750.3285411-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The R9A06G032 clock driver uses an array of packed structures to reduce
kernel size. However, this array contains pointers, which are no longer
aligned naturally, and cannot be relocated on PPC64. Hence when
compile-testing this driver on PPC64 with CONFIG_RELOCATABLE=y (e.g.
PowerPC allyesconfig), the following warnings are produced:
WARNING: 136 bad relocations
c000000000616be3 R_PPC64_UADDR64 .rodata+0x00000000000cf338
c000000000616bfe R_PPC64_UADDR64 .rodata+0x00000000000cf370
...
Fix this by dropping the __packed attribute from the r9a06g032_clkdesc
definition, trading a small size increase for portability.
This increases the 156-entry clock table by 1 byte per entry, but due to
the compiler generating more efficient code for unpacked accesses, the
net size increase is only 76 bytes (gcc 9.3.0 on arm32).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201130085743.1656317-1-geert+renesas@glider.be
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # PowerPC allyesconfig build
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This issue can be reproduced by having a kernel config with
CONFIG_IMX_MBOX=m and CONFIG_MXC_CLK_SCU=m. It's caused by the Makefile
wanting to build clk-scu.o and clk-imx8qxp.o as different targets but
that doesn't work (e.g. MXC_CLK_SCU = y while CLK_IMX8QXP = n)
"obj-$(CONFIG_MXC_CLK_SCU) += clk-imx-scu.o clk-imx-lpcg-scu.o
clk-imx-scu-$(CONFIG_CLK_IMX8QXP) += clk-scu.o clk-imx8qxp.o"
Having MXC_CLK_SCU=y/m while CLK_IMX8QXP=n will cause a linker problem
like below:
LD [M] drivers/clk/imx/clk-imx-scu.o
arm-poky-linux-gnueabi-ld: no input files
Make MXC_CLK_SCU be un-selectable by users so it can only be selected by
the CLK_IMX8QXP option, ensuring the two symbols are built together.
Drop COMPILE_TEST too because this option isn't selectable anymore. We
can remove it from MXC_CLK_SCU because CLK_IMX8QXP selects MXC_CLK_SCU
which already has COMPILE_TEST.
Fixes: e0d0d4d86c ("clk: imx8qxp: Support building i.MX8QXP clock driver as module")
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20201130084624.21113-1-aisheng.dong@nxp.com
[sboyd@kernel.org: Rework commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The use of SIMPLE_DEV_PM_OPS() means that the suspend/resume
functions are now unused when CONFIG_PM is disabled:
drivers/clk/samsung/clk-exynos-clkout.c:219:12: error: 'exynos_clkout_resume' defined but not used [-Werror=unused-function]
219 | static int exynos_clkout_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~
drivers/clk/samsung/clk-exynos-clkout.c:210:12: error: 'exynos_clkout_suspend' defined but not used [-Werror=unused-function]
210 | static int exynos_clkout_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~
Mark them as __maybe_unused to shut up the otherwise harmless warning.
Fixes: 9484f2cb83 ("clk: samsung: exynos-clkout: convert to module driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20201204091616.4128366-1-arnd@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The device_is_bound() is invisible to drivers when built as modules.
It's also not aimed to be used by drivers according to Greg K.H.
Let's remove it from clk-scu driver and find another way to do proper
driver loading sequence.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Rockchip PX2/RK3066 uses these bits in CRU_CLKGATE7_CON:
hclk_i2s_8ch_gate_en bit 4 (dtsi: i2s0)
hclk_i2s0_2ch_gate_en bit 2 (dtsi: i2s1)
hclk_i2s1_2ch_gate_en bit 3 (dtsi: i2s2)
The Rockchip PX3/RK3188 uses this bit in CRU_CLKGATE7_CON:
hclk_i2s_2ch_gate_en bit 2 (dtsi: i2s0)
The bits got somehow mixed up in the clk-rk3188.c file.
The labels in the dtsi files are not suppose to change.
The sclk and hclk names should match for
"trace_event=clk_disable,clk_enable",
so remove GATE HCLK_I2S0 from the common clock tree and
fix the bits in the rk3066 and rk3188 clock tree.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201118135822.9582-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add CLK_SET_RATE_PARENT to sclk for rk3066a i2s and uart clocks,
so that the parent COMPOSITE_FRACMUX and COMPOSITE_NOMUX
also update.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201118135822.9582-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Because clk_prepare_enable() already checked NULL clock parameter,
so the additional check is unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201127090551.50254-1-vulab@iscas.ac.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is a bigger work from Dmitry Osipenko around Tegra SoC memory
controller drivers, mostly towards adding interconnect support and
integration with devfreq. This work touches all Tegra memory controller
drivers and also few other SoC-related parts. It's not yet finished but
the intermediate stage seems ready to merge.
Beside that Tegra 210 memory controller got few fixes and received new
swgroups (work of Nicolin Chen).
-----BEGIN PGP SIGNATURE-----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=EUPM
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-tegra-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.11 - Tegra SoC
There is a bigger work from Dmitry Osipenko around Tegra SoC memory
controller drivers, mostly towards adding interconnect support and
integration with devfreq. This work touches all Tegra memory controller
drivers and also few other SoC-related parts. It's not yet finished but
the intermediate stage seems ready to merge.
Beside that Tegra 210 memory controller got few fixes and received new
swgroups (work of Nicolin Chen).
* tag 'memory-controller-drv-tegra-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl: (38 commits)
memory: tegra30-emc: Remove unnecessary of_node_put in tegra_emc_probe
memory: tegra: Complete tegra210_swgroups
memory: tegra30-emc: Continue probing if timings are missing in device-tree
memory: tegra30-emc: Make driver modular
memory: tegra30: Add FIFO sizes to memory clients
memory: tegra20-emc: Add devfreq support
memory: tegra20-emc: Remove IRQ number from error message
memory: tegra20-emc: Factor out clk initialization
memory: tegra20-emc: Use dev_pm_opp_set_clkname()
memory: tegra: Correct stub of devm_tegra_memory_controller_get()
memory: tegra20: Support interconnect framework
memory: tegra20-emc: Continue probing if timings are missing in device-tree
memory: tegra20-emc: Make driver modular
memory: tegra-mc: Add interconnect framework
memory: tegra: Add missing latency allowness entry for Page Table Cache
memory: tegra: Remove superfluous error messages around platform_get_irq()
memory: tegra: Use devm_platform_ioremap_resource()
memory: tegra: Add and use devm_tegra_memory_controller_get()
dt-bindings: host1x: Document new interconnect properties
dt-bindings: tegra30-actmon: Document OPP and interconnect properties
...
Link: https://lore.kernel.org/r/20201126191241.23302-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BPMP firmware ABI expects the rate inputs in int64_t. However,
tegra_bpmp_clk_round_rate() and tegra_bpmp_clk_set_rate() functions
directly assign 'unsigned long' inputs to a int64_t value causing
unexpected rounding errors.
Fix this by clipping the input rate to S64_MAX.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
[mperttunen: slight cleanup]
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the MIPI DSI Host Pixel Clock, unlike AXG, the pixel clock can be different
from the VPU ENCL output clock to feed the DSI Host controller with a different clock rate.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201126141600.2084586-3-narmstrong@baylibre.com
Qualcomm CE clock resource that is managed by BCM is required
by crypto driver to access the core clock.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201119155233.3974286-3-thara.gopinath@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PLL status polling loops in the set_rate callbacks of some PLLs
have no timeout detection and may become endless loops when something
goes wrong with the PLL.
For some PLLs there is already the ktime API based timeout detection,
but it will not work in all conditions when .set_rate gets called.
In particular, before the clocksource is initialized or when the
timekeeping is suspended.
This patch adds a common helper with the PLL status bit polling and
timeout detection. For conditions where the timekeeping API should not
be used a simple readl_relaxed/cpu_relax() busy loop is added with the
iterations limit derived from measurements of readl_relaxed() execution
time for various PLL types and Exynos SoCs variants.
Actual PLL lock time depends on the P divider value, the VCO frequency
and a constant PLL type specific LOCK_FACTOR and can be calculated as
lock_time = Pdiv * LOCK_FACTOR / VCO_freq
For the ktime API use cases a common timeout value of 20 ms is applied
for all the PLLs with an assumption that maximum possible value of Pdiv
is 64, maximum possible LOCK_FACTOR value is 3000 and minimum VCO
frequency is 24 MHz.
Link: https://lore.kernel.org/r/20201120155731.26898-1-s.nawrocki@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
So far all Exynos, S3C64xx and S5Pv210 clock units were selected by
respective SOC/ARCH Kconfig option. On a kernel built for selected
SoCs, this allowed to build only limited set of matching clock drivers.
However compile testing was not possible in such case as Makefile object
depends on SOC/ARCH option.
Add separate Kconfig options for each of them to be able to compile
test.
Link: https://lore.kernel.org/r/20201119164509.754851-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Make it possible to build all clk drivers as modules, but default
remains built-in.
No functional changes.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201118191405.36798-1-khilman@baylibre.com
This adds the MIPI DSI Host clock, used to measure the signal timings
(ENC VSYNC or DW-MIPI-DSI eDPI timings).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200915124553.8056-5-narmstrong@baylibre.com
Add the clocks entries used in the video clock path, the clock path is
doubled to permit having different synchronized clocks for different parts
of the video pipeline.
The AXG only has a single ENCL CTS clock and even if VCLK exist along
VCLK2, only VCLK2 is used since it clocks the MIPI DSI IP directly.
All dividers are flagged with CLK_GET_RATE_NOCACHE, and all gates are
flagged with CLK_IGNORE_UNUSED since they are currently directly handled by
the Meson DRM Driver. Once the DRM Driver is fully migrated to using the
Common Clock Framework to handle the video clock tree, the
CLK_GET_RATE_NOCACHE and CLK_IGNORE_UNUSED will be dropped.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200915124553.8056-4-narmstrong@baylibre.com
Return values from read_dt_param() will be either TRUE (1) or
FALSE (0), while dfll_fetch_pwm_params() returns 0 on success
or an ERR code on failure.
So this patch fixes the bug of returning 0 on failure.
Fixes: 36541f0499 ("clk: tegra: dfll: support PWM regulator control")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Similar to what we've done for IPU and DSP let's ignore the status bit
for the IVA clkctrl register.
The clkctrl status won't change unless the related rstctrl is deasserted,
and the rstctrl status won't change unless the clkctrl is enabled.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to what we've done for IPU and DSP let's ignore the status bit
for the IVA clkctrl register.
The clkctrl status won't change unless the related rstctrl is deasserted,
and the rstctrl status won't change unless the clkctrl is enabled.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend and resume to work with genpd on am4, we must keep
l3 main clock always on. Otherwise prm_omap driver will shut down the l3
main clock on suspend when simple-pm-bus and GENPD_FLAG_PM_CLK are used.
Note that we already keep the l3 main clock always on with the legacy
platform code.
Later on we may want to start managing the l3 main clock with a dedicated
interconnect driver instead of using simple-pm-bus and GENPD_FLAG_PM_CLK.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend and resume to work with genpd on am3, we must keep
l3 main clock always on. Otherwise prm_omap driver will shut down the l3
main clock on suspend when simple-pm-bus and GENPD_FLAG_PM_CLK are used.
Note that we already keep the l3 main clock always on with the legacy
platform code.
Later on we may want to start managing the l3 main clock with a dedicated
interconnect driver instead of using simple-pm-bus and GENPD_FLAG_PM_CLK.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On SM8250 MMCX power domain is required to access MMDS_GDSC registers.
This power domain is expressed as mmcx-supply regulator property. Use
this regulator as MDSS_GDSC supply.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201023131925.334864-6-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Until now, nothing was done to unregister the dvfs clock notifiers of the
Amlogic g12 SoC family. This is not great but this driver was not really
expected to be unloaded. With the ongoing effort to build everything as
module for this platform, this needs to be cleanly handled.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021163847.595189-3-jbrunet@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a memory managed variant of clk_notifier_register() to make life easier
on clock consumers using notifiers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021163847.595189-2-jbrunet@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
g12 clock controller used __clk_lookup() to get struct clk from a
struct clk_hw. This type of hack is no longer required as CCF now provides
the necessary functions to get this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021162147.563655-4-jbrunet@baylibre.com
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_register() is deprecated. Using 'clk' member of struct clk_hw is
discouraged. With this constraint, it is difficult for driver to
register clocks using the clk_hw API and then use the clock with
the consumer API
This adds a simple helper, clk_hw_get_clk(), to get a struct clk from
a struct clk_hw. Like other clk_get() variant, each call to this helper
must be balanced with a call to clk_put(). To make life easier on the
consumers, a memory managed version is provided as well.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021162147.563655-3-jbrunet@baylibre.com
Tested-by: Kevin Hilman <khilman@baylibre.com>
[sboyd@kernel.org: Fix kernel-doc]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In clk-devres.c, devm_clk_release() is used to call clk_put() memory
managed clock. In clk.c the same name, in a different scope is used to call
clk_unregister().
As it stands, it is not really a problem but it does not readability,
especially if we need to call clk_put() on managed clock in clk.c
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021162147.563655-2-jbrunet@baylibre.com
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
make clang-analyzer on x86_64 defconfig caught my attention with:
drivers/clk/clk.c:423:19:
warning: Value stored to 'parent' during its initialization is never read
[clang-analyzer-deadcode.DeadStores]
struct clk_core *parent = ERR_PTR(-ENOENT);
^
Commit fc0c209c14 ("clk: Allow parents to be specified without string
names") introduced clk_core_fill_parent_index() with this unneeded
dead-store initialization.
So, simply remove this unneeded dead-store initialization to make
clang-analyzer happy.
As compilers will detect this unneeded assignment and optimize this anyway,
the resulting object code is identical before and after this change.
No functional change. No change to object code.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201106094820.30167-1-lukas.bulwahn@gmail.com
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Let's call pm_runtime_get() here instead of calling the PM clk APIs
directly. This avoids a compilation problem on CONFIG_PM=n where the
pm_clk_runtime_{resume,suspend}() functions don't exist and covers the
intent, i.e. enable the clks for this device so we can program PLL
settings.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Taniya Das <tdas@codeaurora.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Fixes: 15d09e830b ("clk: qcom: camcc: Add camera clock controller driver for SC7180")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201114174408.579047-1-sboyd@kernel.org
Clean up the first driver if the second driver can't be registered.
Fixes: 4ee9fe3e29 ("clk: qcom: lpass-sc7180: Disentangle the two clock devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201113101419.GC168908@mwanda
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Exynos clock output driver can be built as module (it does not have
to be part of core init process) for better customization. Adding a
KConfig entry allows also compile testing for build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20201110193749.261367-1-krzk@kernel.org
Fix the following sparse warning:
./clk-scu.c:23:20: warning: symbol 'pd_np' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mq.c:626:34: warning:
‘imx8mq_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mp.c:751:34: warning:
‘imx8mp_clk_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mn.c:592:34: warning:
‘imx8mn_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mm.c:641:34: warning:
‘imx8mm_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch fixes below warning reported by coccicheck:
./clk-gate2.c:57:5-8: Unneeded variable: "ret". Return "0" on line 68
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We're going to modularize Tegra EMC drivers and some of the EMC-clock
driver symbols need to be exported.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
LPASS Always ON Clock controller has one GFM mux to control VA
and TX clocks to codec macro on LPASS.
This patch adds support to this mux.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20201026120221.18984-5-srinivas.kandagatla@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The sc7180 lpass clock driver manages two different devices. These
two devices were tangled together, using one probe and a lookup to
figure out the real probe. I think it's cleaner to really separate
the probe for these two devices since they're really different things,
just both managed by the same driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201019154857.v5.2.I75c409497d4dea9daefa53ec5f93824081c4ecbe@changeid
Reviewed-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Let's convert the lpass clock control driver to use devm. This is a
few more lines of code, but it will be useful in a later patch which
disentangles the two devices handled by this driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201019154857.v5.1.I4567b5e7e17bbb15ef063d447cb83fd43746cb18@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the camera clock controller found on SC7180 based devices.
This would allow camera drivers to probe and control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1602873815-1677-5-git-send-email-tdas@codeaurora.org
[sboyd@kernel.org: Mark hw array static, add UL to big vco numbers]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Introduce clk_alpha_pll_write_config and alpha_pll_check_rate_margin
helper functions to be across PLL configure functions and PLL set rate
functions.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1602873815-1677-2-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
noc/axi/ahb are bus clk, not peripheral clk.
Since peripheral clk has a limitation that for peripheral clock slice,
IP clock slices must be stopped to change the clock source.
However if the bus clk is marked as critical clk peripheral, the
assigned clock parent operation will fail.
So we added CLK_SET_PARENT_GATE flag to avoid glitch.
And add imx8m_clk_hw_composite_bus_critical for bus critical clock usage
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1604229834-25594-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Protect against enabling/disabling the gate while we're
checking if it is enabled.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On some i.MX8 platforms, there are HW gates that share the same bit.
So in order to make this clock type more usable, use a mask to specify
how many bits belong to those HW gates.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Seems the logic here was wrong all along. For example, if
the cgr_val is 2 (0b10), the clk_gate2_reg_is_enabled would
report the clock as disabled. So check against cgr_val instead.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move all the register writing to the newly added clk_gate2_do_shared_clks
and call that everywhere need needed. Cleans up the code a little bit.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was a hack which would allow multiple HW gates to be controlled
by a single bit. The only user of this is the imx_dev_clk_hw_gate_shared
which is not used anywhere as of now. Basically, complicates the logic
of the driver for no reason.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit e0d0d4d86c ("clk: imx8qxp: Support building i.MX8QXP clock
driver as module"), clk-scu.c and clk-imx8qxp.c are complied in one module,
thus there can be only one module_init() in those two files.
Commit 77d8f3068c ("clk: imx: scu: add two cells binding support")
introduced another module_init() in clk_scu.c which caused the errors
below.
To fix the issue, we can remove the unnecessary builtin_platform_driver
from clk_scu.c and directly register the driver in imx_clk_scu_init().
CC [M] drivers/clk/imx/clk-scu.o
In file included from ../include/linux/of_device.h:6,
from ../include/linux/of_platform.h:12,
from ../drivers/clk/imx/clk-scu.c:11:
../drivers/clk/imx/clk-scu.c: In function ‘imx_clk_scu_init’:
../drivers/clk/imx/clk-scu.c:176:35: error: ‘imx_clk_scu_driver’ undeclared (first use in this function); did you mean ‘imx_clk_scu_init’?
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:176:35: note: each undeclared identifier is reported only once for each function it appears in
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:177:1: error: control reaches end of non-void function [-Werror=return-type]
177 | }
| ^
At top level:
../drivers/clk/imx/clk-scu.c:470:31: warning: ‘imx_clk_scu_driver’ defined but not used [-Wunused-variable]
470 | static struct platform_driver imx_clk_scu_driver = {
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pointer np is being initialized with a value that is never read
and it is being updated with a value later on. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nesting container_of() causes warnings with W=2, which is
annoying if it happens in headers and fills the build log
like:
In file included from drivers/clk/qcom/clk-alpha-pll.c:6:
drivers/clk/qcom/clk-alpha-pll.c: In function 'clk_alpha_pll_hwfsm_enable':
include/linux/kernel.h:852:8: warning: declaration of '__mptr' shadows a previous local [-Wshadow]
852 | void *__mptr = (void *)(ptr); \
| ^~~~~~
drivers/clk/qcom/clk-alpha-pll.c:155:31: note: in expansion of macro 'container_of'
155 | #define to_clk_alpha_pll(_hw) container_of(to_clk_regmap(_hw), \
| ^~~~~~~~~~~~
drivers/clk/qcom/clk-regmap.h:27:28: note: in expansion of macro 'container_of'
27 | #define to_clk_regmap(_hw) container_of(_hw, struct clk_regmap, hw)
| ^~~~~~~~~~~~
drivers/clk/qcom/clk-alpha-pll.c:155:44: note: in expansion of macro 'to_clk_regmap'
155 | #define to_clk_alpha_pll(_hw) container_of(to_clk_regmap(_hw), \
| ^~~~~~~~~~~~~
drivers/clk/qcom/clk-alpha-pll.c:254:30: note: in expansion of macro 'to_clk_alpha_pll'
254 | struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
| ^~~~~~~~~~~~~~~~
include/linux/kernel.h:852:8: note: shadowed declaration is here
852 | void *__mptr = (void *)(ptr); \
| ^~~~~~
Redefine two copies of the to_clk_regmap() macro as inline functions
to avoid a lot of these.
Fixes: ea11dda9e0 ("clk: meson: add regmap clocks")
Fixes: 085d7a4554 ("clk: qcom: Add a regmap type clock struct")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161411.3708639-1-arnd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Exynos clkout driver depends on board input clock (typically XXTI or
XUSBXTI), however on Exynos4 boards these clocks were modeled as part of
SoC clocks (Exynos4 clocks driver). Obviously this is not proper, but
correcting it would break DT backward compatibility.
Both drivers - clkout and Exynos4 clocks - register the clock providers
with CLK_OF_DECLARE/OF_DECLARE_1 so their order is fragile (in the
Makefile clkout is behind Exynos4 clock). It will work only if the
Exynos4 clock driver comes up before clkout.
A change in DTS adding input clock reference to Exynos4 clocks input
PLL, see reverted commit eaf2d2f689 ("ARM: dts: exynos: add input
clock to CMU in Exynos4412 Odroid"), caused probe reorder: the clkout
appeared before Exynos4 clock provider. Since clkout depends on Exynos4
clocks and does not support deferred probe, this did not work and caused
later failure of usb3503 USB hub probe which needs clkout:
[ 5.007442] usb3503 0-0008: unable to request refclk (-517)
The Exynos clkout driver is not a critical/core clock so there is
actually no problem in instantiating it later, as a regular module.
This removes specific probe ordering and adds support for probe
deferral.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20201001165646.32279-3-krzk@kernel.org
There is no case (and none foreseen) where we would need to disable the
SDn clock. So, for simplicity, remove its handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200922120036.10298-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
LPCG clock state may be lost when it's power domain is completely
off during system suspend/resume and we need save and restore the
state properly.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Used to support runtime pm.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
One LPCG controller supports up to 8 clock outputs while each of them
is fixed to 4 bits. It supports only gating function with fixed bits.
So we can use the clk-indices to fetch the corresponding clock idx from
device tree. With this way, we can write a generic LPCG clock drivers.
This patch add that support to parse clocks from device tree.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Clock state will be lost when its power domain is completely off
during system suspend/resume. So we save and restore the state
accordingly in suspend/resume callback.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bypass cpu power domains which are owned by ATF.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch implements the new two cells binding for SCU clocks.
The usage is as follows:
clocks = <&uart0_clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>
Due to each SCU clock is associated with a power domain, without power
on the domain, the SCU clock can't work. So we create platform devices
for each domain clock respectively and manually attach the required domain
before register the clock devices, then we can register clocks in the
clock platform driver accordingly.
Note because we do not have power domain info in device tree and the SCU
resource ID is the same for power domain and clock, so we use resource ID
to find power domains.
Later, we will also use this clock platform driver to support suspend/resume
and runtime pm.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
of various clk driver updates. The biggest driver updates in terms of lines of
code is the Allwinner driver, closely followed by the Qualcomm and Mediatek
drivers. All of those hit high because we add so many lines of clk data. Coming
in fourth place is i.MX which also adds a bunch of clk data. This accounts for
the new driver additions this time around.
Otherwise the patches are lots of little cleanups and fixes for various clk
drivers that have baked in linux-next for a while. I suppose one highlight or
theme is that more clk drivers are being updated to work as modules, which is
interesting to see such critical SoC infrastructure work as a loadable module.
New Drivers:
- Support qcom SM8150/SM8250 video and display clks
- Support Mediatek MT8167 clks
- Add clock for CRC block found on vf610 SoCs
- Add support for the Renesas R-Car V3U (R8A779A0) SoC
- Add support for the VSP for Resizing clock on Renesas RZ/G1H
- Support Allwinner A100 SoC clks
Removed Drivers:
- Remove i.MX21 clock driver, as i.MX21 platform support is being dropped
Updates:
- Change how qcom's display port clks work
- Small non-critical fixes for TI clk driver
- Remove various unused variables in clk drivers
- Allow Rockchip clk driver to be a module
- Remove most __clk_lookup() calls in Samsung drivers (yay!)
- Support building i.MX ARMv8 platforms clock driver as module
- Some kerneldoc fixes here and there
- A couple of minor i.MX clk data corrections
- Update audio clock inverter and fdiv2 flag on Amlogic g12
- Make amlogic clk drivers configurable in Kconfig
- Fix Renesas VSP clock names to match corrected hardware documentation
- Sigma-delta modulation on Allwinner R40
- Various fixes for at91 clk driver
- Use semicolons instead of commas in some places
- Mark some variables const so they can move to RO memory
-----BEGIN PGP SIGNATURE-----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=sKI8
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This contains no changes to the core framework. It is a collection of
various clk driver updates.
The biggest driver updates in terms of lines of code is the Allwinner
driver, closely followed by the Qualcomm and Mediatek drivers. All of
those hit high because we add so many lines of clk data. Coming in
fourth place is i.MX which also adds a bunch of clk data. This
accounts for the new driver additions this time around.
Otherwise the patches are lots of little cleanups and fixes for
various clk drivers that have baked in linux-next for a while. I
suppose one highlight or theme is that more clk drivers are being
updated to work as modules, which is interesting to see such critical
SoC infrastructure work as a loadable module.
New Drivers:
- Support qcom SM8150/SM8250 video and display clks
- Support Mediatek MT8167 clks
- Add clock for CRC block found on vf610 SoCs
- Add support for the Renesas R-Car V3U (R8A779A0) SoC
- Add support for the VSP for Resizing clock on Renesas RZ/G1H
- Support Allwinner A100 SoC clks
Removed Drivers:
- Remove i.MX21 clock driver, as i.MX21 platform support is being
dropped
Updates:
- Change how qcom's display port clks work
- Small non-critical fixes for TI clk driver
- Remove various unused variables in clk drivers
- Allow Rockchip clk driver to be a module
- Remove most __clk_lookup() calls in Samsung drivers (yay!)
- Support building i.MX ARMv8 platforms clock driver as module
- Some kerneldoc fixes here and there
- A couple of minor i.MX clk data corrections
- Update audio clock inverter and fdiv2 flag on Amlogic g12
- Make amlogic clk drivers configurable in Kconfig
- Fix Renesas VSP clock names to match corrected hardware
documentation
- Sigma-delta modulation on Allwinner R40
- Various fixes for at91 clk driver
- Use semicolons instead of commas in some places
- Mark some variables const so they can move to RO memory"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (102 commits)
clk: imx8mq: Fix usdhc parents order
clk: qcom: gdsc: Keep RETAIN_FF bit set if gdsc is already on
clk: Restrict CLK_HSDK to ARC_SOC_HSDK
clk: at91: sam9x60: support only two programmable clocks
clk: ingenic: Respect CLK_SET_RATE_PARENT in .round_rate
clk: ingenic: Don't tag custom clocks with CLK_SET_RATE_PARENT
clk: ingenic: Don't use CLK_SET_RATE_GATE for PLL
clk: ingenic: Use readl_poll_timeout instead of custom loop
clk: ingenic: Use to_clk_info() macro for all clocks
clk: bcm2835: add missing release if devm_clk_hw_register fails
clk: at91: clk-sam9x60-pll: remove unused variable
clk: at91: clk-main: update key before writing AT91_CKGR_MOR
clk: at91: remove the checking of parent_name
clk: clk-prima2: fix return value check in prima2_clk_init()
clk: mmp2: Fix the display clock divider base
clk: pxa: Constify static struct clk_ops
clk: baikal-t1: Mark Ethernet PLL as critical
clk: qoriq: modify MAX_PLL_DIV to 32
clk: axi-clkgen: Set power bits for fractional mode
clk: axi-clkgen: Add support for fractional dividers
...
- Support qcom SM8150/SM8250 video and display clks
- Change how qcom's display port clks work
* clk-ingenic:
clk: ingenic: Respect CLK_SET_RATE_PARENT in .round_rate
clk: ingenic: Don't tag custom clocks with CLK_SET_RATE_PARENT
clk: ingenic: Don't use CLK_SET_RATE_GATE for PLL
clk: ingenic: Use readl_poll_timeout instead of custom loop
clk: ingenic: Use to_clk_info() macro for all clocks
* clk-at91:
clk: at91: sam9x60: support only two programmable clocks
clk: at91: clk-sam9x60-pll: remove unused variable
clk: at91: clk-main: update key before writing AT91_CKGR_MOR
clk: at91: remove the checking of parent_name
* clk-kconfig:
clk: Restrict CLK_HSDK to ARC_SOC_HSDK
* clk-imx:
clk: imx8mq: Fix usdhc parents order
clk: imx: imx21: Remove clock driver
clk: imx: gate2: Fix a few typos
clk: imx: Fix and update kerneldoc
clk: imx: fix i.MX7D peripheral clk mux flags
clk: imx: fix composite peripheral flags
clk: imx: Correct the memrepair clock on imx8mp
clk: imx: Correct the root clk of media ldb on imx8mp
clk: imx: vf610: Add CRC clock
clk: imx: Explicitly include bits.h
clk: imx8qxp: Support building i.MX8QXP clock driver as module
clk: imx8m: Support module build
clk: imx: Add clock configuration for ARMv7 platforms
clk: imx: Support building i.MX common clock driver as module
clk: composite: Export clk_hw_register_composite()
clk: imx6sl: Use BIT(x) to avoid shifting signed 32-bit value by 31 bits
* clk-qcom:
clk: qcom: gdsc: Keep RETAIN_FF bit set if gdsc is already on
clk: qcom: Add display clock controller driver for SM8150 and SM8250
dt-bindings: clock: add QCOM SM8150 and SM8250 display clock bindings
clk: qcom: add video clock controller driver for SM8250
clk: qcom: add video clock controller driver for SM8150
dt-bindings: clock: add SM8250 QCOM video clock bindings
dt-bindings: clock: add SM8150 QCOM video clock bindings
dt-bindings: clock: combine qcom,sdm845-videocc and qcom,sc7180-videocc
clk: qcom: gcc-msm8994: Add missing clocks, resets and GDSCs
clk/qcom: fix spelling typo
clk: qcom: gcc-sdm660: Fix wrong parent_map
clk: qcom: dispcc: Update DP clk ops for phy design
clk: qcom: gcc-msm8939: remove defined but not used variables
clk: qcom: ipq8074: make pcie0_rchng_clk_src static
* clk-prima2:
clk: clk-prima2: fix return value check in prima2_clk_init()
* clk-bcm:
clk: bcm2835: add missing release if devm_clk_hw_register fails
clk: bcm: rpi: Add register to control pixel bvb clk
* clk-semicolon:
clk: meson: use semicolons rather than commas to separate statements
clk: mvebu: ap80x-cpu: use semicolons rather than commas to separate statements
clk: uniphier: use semicolons rather than commas to separate statements
* clk-axi-clkgen:
clk: axi-clkgen: Set power bits for fractional mode
clk: axi-clkgen: Add support for fractional dividers
* clk-qoriq:
clk: qoriq: modify MAX_PLL_DIV to 32
* clk-baikal:
clk: baikal-t1: Mark Ethernet PLL as critical
* clk-const:
clk: pxa: Constify static struct clk_ops
* clk-mmp2:
clk: mmp2: Fix the display clock divider base
According to the latest RM (see Table 5-1. Clock Root Table),
both usdhc root clocks have the parent order as follows:
000 - 25M_REF_CLK
001 - SYSTEM_PLL1_DIV2
010 - SYSTEM_PLL1_CLK
011 - SYSTEM_PLL2_DIV2
100 - SYSTEM_PLL3_CLK
101 - SYSTEM_PLL1_DIV3
110 - AUDIO_PLL2_CLK
111 - SYSTEM_PLL1_DIV8
So the audio_pll2_out and sys3_pll_out have to be swapped.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Cosmin Stefan Stoica <cosmin.stoica@nxp.com>
Link: https://lore.kernel.org/r/1602753944-30757-1-git-send-email-abel.vesa@nxp.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If the GDSC is enabled out of boot but doesn't have the retain ff bit
set we will get confusing results where the registers that are powered
by the GDSC lose their contents on the first power off of the GDSC but
thereafter they retain their contents. This is because gdsc_init() fails
to make sure the RETAIN_FF bit is set when it probes the GDSC the first
time and thus powering off the GDSC causes the register contents to be
reset. We do set the RETAIN_FF bit the next time we power on the GDSC,
see gdsc_enable(), so that subsequent GDSC power off's don't lose
register contents state.
Forcibly set the bit at device probe time so that the kernel's assumed
view of the GDSC is consistent with the state of the hardware. This
fixes a problem where the audio PLL doesn't work on sc7180 when the
bootloader leaves the lpass_core_hm GDSC enabled at boot (e.g. to make a
noise) but critically doesn't set the RETAIN_FF bit.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Taniya Das <tdas@codeaurora.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 173722995c ("clk: qcom: gdsc: Add support to enable retention of GSDCR")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201017020137.1251319-1-sboyd@kernel.org
Reviewed-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org>
The HSDK PLL driver is only useful when building for an ARC HSDK
platform.
As ARC selects OF, the dependency on OF can just be replaced by a
dependency on ARC_SOC_HSDK.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200807094351.1046-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to datasheet (Chapter 29.16.13, PMC Programmable Clock Register)
there are only two programmable clocks on SAM9X60.
Fixes: 01e2113de9 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1602686072-28296-1-git-send-email-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clocks that don't have a divider are in our case all marked with the
CLK_SET_RATE_PARENT flag. In this case, the .round_rate implementation
should modify the value pointed to by parent_rate, in order to propagate
the rate change to the parent, as explained in the documentation of
clk_set_rate().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-5-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The custom clocks have custom functions to round, get or set their rate.
Therefore, we can't assume that they need the CLK_SET_RATE_PARENT flag.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-4-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CLK_SET_RATE_GATE means that the clock must be gated when being
reclocked. This is not the case for the PLLs in Ingenic SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-3-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use the readl_poll_timeout() function instead of rolling our own
busy-wait loops. This makes the code simpler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-2-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The to_clk_info() previously had a BUG_ON() to check that it was only
called for PLL clocks. Yet, all the other clocks were doing the exact
same thing the macro does, in-line.
Move the to_clk_info() macro to the top of the file, remove the
hardcoded BUG_ON(), and use it everywhere it makes sense.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In the implementation of bcm2835_register_pll(), the allocated pll is
leaked if devm_clk_hw_register() fails to register hw. Release pll if
devm_clk_hw_register() fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20200809231202.15811-1-navid.emamdoost@gmail.com
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix variable set but not used compilation warning.
Fixes: 43b1bb4a9b ("clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1598338751-20607-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAMA5D2 datasheet specifies on chapter 33.22.8 (PMC Clock Generator
Main Oscillator Register) that writing any value other than
0x37 on KEY field aborts the write operation. Use the key when
selecting main clock parent.
Fixes: 27cb1c2083 ("clk: at91: rework main clk implementation")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1598338751-20607-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no need to check parent_name variable while assigning it to
init.parent_names. parent_name variable is already checked at
the beginning of at91_clk_register_peripheral() function.
Fixes: 6114067e43 ("clk: at91: add PMC peripheral clocks")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1598338751-20607-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200921034522.9077-1-vulab@iscas.ac.cn
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Constify a couple of static struct clk_ops that are not modified. Their
only usage is inside the macros and their address is passed to
clk_register_composite() which takes pointers to const struct clk_ops.
This allows the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200922184715.1854-1-rikard.falkeborn@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We've discovered that disabling the so called Ethernet PLL causes reset of
the devices consuming its outgoing clock. The resets happen automatically
even if each underlying clock gate is turned off. Due to that we can't
disable the Ethernet PLL until the kernel is prepared for the corresponding
resets. So for now just mark the PLL clock provider as critical.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: linux-mips@vger.kernel.org
Link: https://lore.kernel.org/r/20200920110335.18034-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Using the fractional dividers requires some additional power bits to be
set.
The fractional power bits are not documented and the current heuristic
for setting them seems be insufficient for some cases. Just always set all
the fractional power bits when in fractional mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201001085948.21412-2-alexandru.ardelean@analog.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The axi-clkgen has (optional) fractional dividers on the output clock
divider and feedback clock divider path. Utilizing the fractional dividers
allows for a better resolution of the output clock, being able to
synthesize more frequencies.
Rework the driver support to support the fractional register fields, both
for setting a new rate as well as reading back the current rate from the
hardware.
For setting the rate if no perfect divider settings were found in
non-fractional mode try again in fractional mode and see if better settings
can be found. This appears to be the recommended mode of operation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201001085948.21412-1-alexandru.ardelean@analog.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the display clock controller found on SM8150 and SM8250.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Link: https://lore.kernel.org/r/20200927190653.13876-3-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the video clock controller found on SM8250 based devices.
Derived from the downstream driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200923160635.28370-6-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the video clock controller found on SM8150 based devices.
Derived from the downstream driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200923160635.28370-5-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This change adds GDSCs, resets and most of the missing
clocks to the msm8994 GCC driver. The remaining ones
are of local_vote_clk and gate_clk type, which are not
yet supported upstream. Also reorder them to match the
original downstream driver.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20201005145855.149206-1-konradybcio@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the following clock support for MT8167 SoC: topckgen, apmixedsys,
infracfg, audsys, imgsys, mfgcfg, vdecsys.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20200918132303.2831815-2-fparent@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We can get down to this return value from ERR_CAST() without
initializing hw. Set it to -ENOMEM so that we always return something
sane.
Fixes the following smatch warning:
drivers/clk/rockchip/clk-half-divider.c:228 rockchip_clk_register_halfdiv() error: uninitialized symbol 'hw'.
drivers/clk/rockchip/clk-half-divider.c:228 rockchip_clk_register_halfdiv() warn: passing zero to 'ERR_CAST'
Cc: Elaine Zhang <zhangqing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Fixes: 956060a527 ("clk: rockchip: add support for half divider")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- A series from Fabio Estevam to remove legacy non-DT i.MX platforms
support and related board files. This is a natural move, as the
platforms had been converted to DT for years, and we have not seen
any users around these legacy non-DT support for a while.
- Enable cpufreq support for i.MX7ULP platform.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl9qmaAUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6OUAgAtFkBiF4YeAh7AoHbCHnecot5Ywbv
cvv9dktXBJNjzZSIO8RbvDterNHuamQm433CDz9GYBb2hMWM0ZvlARn2lj+ixX0e
vbQs2DUu7XNvxpGxsKCDbs9DNJmjsnfTLKjXd6D/OYD0+QRgYJJAqLt0rbzSqY3k
2R5yy3yLqJRQ5kGKDde+QQj2uFc1flfSsTXugbmYpsu3xPYXKmIwTqy4wgVUgXWg
CUEZDXFi5Wny+uKMnVtojm0Xyj2+R8HutHWBmEgkhtItgjrf9+OamnIBtvCWUtXe
+7PQswaZsdmbtzB0P9nHRsMjAEJhBxUmUb0X2piOI0vPfkGIBygDzs2nxQ==
=QAok
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/soc
i.MX SoC update for 5.10:
- A series from Fabio Estevam to remove legacy non-DT i.MX platforms
support and related board files. This is a natural move, as the
platforms had been converted to DT for years, and we have not seen
any users around these legacy non-DT support for a while.
- Enable cpufreq support for i.MX7ULP platform.
* tag 'imx-soc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (26 commits)
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: imx: Remove remnant board file support pieces
ARM: imx: Remove imx device directory
ARM: imx: Remove iomux-v3 board code
ARM: imx3: Remove imx3 soc_init()
ARM: imx31: Remove remaining i.MX31 board code
ARM: imx27: Retrieve AVIC base address from devicetree
ARM: imx27: Get rid of mm-imx27.c
ARM: imx27: Remove iomux-v1 board code
ARM: imx27: Remove imx27_soc_init()
ARM: imx7ulp: enable cpufreq
...
Link: https://lore.kernel.org/r/20200923073009.23678-2-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
The provider variable is already dereferenced earlier in this function.
Drop the check for NULL as it is impossible.
Found with smatch
drivers/clk/tegra/clk-tegra210-emc.c:131 tegra210_clk_emc_set_rate() warn: variable dereferenced before check 'provider' (see line 124)
Cc: Joseph Lo <josephl@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Fixes: 0ac65fc946 ("clk: tegra: Implement Tegra210 EMC clock")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200922191641.2305144-1-sboyd@kernel.org
Acked-by: Thierry Reding <treding@nvidia.com>
Fix a memory leak induced by not calling clk_put after doing of_clk_get.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907082600.454-3-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk pointer passed to omap2_clk_(deny|allow)_idle can be NULL, so
add checks for this.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907082600.454-2-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently, we request exact clock rates from the firmware to be set with
set_rate. Due to some rounding errors and internal functionality of the
firmware itself, this can fail. Thus, add some slack to the set_rate
functionality so that we are always guaranteed to pass. The firmware
always attempts to use frequency as close to the target freq as
possible despite the slack given here.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907085740.1083-4-t-kristo@ti.com
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Cache results of the latest query rate operation. This optimizes the
firmware interface a bit, avoiding unnecessary calls to firmware if we
know the result already; the firmware interface is pretty expensive
to use for query rate functionality.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907085740.1083-3-t-kristo@ti.com
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The DT clock probe loop incorrectly terminates after processing "clocks"
only, fix this by re-starting the loop when all entries for current
DT property have been parsed.
Fixes: 8e48b33f9d ("clk: keystone: sci-clk: probe clocks from DT instead of firmware")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907085740.1083-2-t-kristo@ti.com
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
./drivers/clk/mediatek/clk-mt6765.c:912:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 1aca9939bf ("clk: mediatek: Add MT6765 clock support")
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1600761065-71353-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
drivers/clk/socfpga/clk-agilex.c:24:37: warning: ‘cntr_mux’ defined but not used [-Wunused-const-variable=]
static const struct clk_parent_data cntr_mux[] = {
^~~~~~~~
There is no caller in tree, so can remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200915020950.4688-1-yuehaibing@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
'err' is assigned but never read:
/drivers/clk/clk-si5341.c: In function ‘si5341_output_get_parent’:
drivers/clk/clk-si5341.c:886:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200916161740.14173-5-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
'clk' is assigned but never read:
drivers/clk/mmp/clk-of-pxa1928.c: In function ‘pxa1928_pll_init’:
drivers/clk/mmp/clk-of-pxa1928.c:71:14: warning: variable ‘clk’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200916161740.14173-4-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The at91sam9g45_pcr_layout is not used so drop it to fix build warning:
drivers/clk/at91/at91sam9g45.c:49:36: warning:
'at91sam9g45_pcr_layout' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200916161740.14173-1-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add missing kerneldoc to fix compile warning:
drivers/clk/davinci/da8xx-cfgchip.c:578: warning: Function parameter or member 'dev' not described in 'da8xx_cfgchip_register_usb1_clk48'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20200916161740.14173-3-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add missing kerneldoc to fix compile warnings like:
drivers/clk/clk-fixed-factor.c:211: warning: Function parameter or member 'node' not described in 'of_fixed_factor_clk_setup'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200916161740.14173-2-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The driver was using subsys_initcall() because in old times deferred
probe was not supported everywhere and specific ordering was needed.
Since probe deferral works fine and specific ordering is discouraged
(hides dependencies between drivers and couples their boot order), the
driver can be converted to regular module_platform_driver.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200921203558.19554-1-krzk@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To use QHD or higher, we need to modify the pixel_bvb_clk value. So
add register to control this clock.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Link: https://lore.kernel.org/r/20200901040759.29992-2-hoegeun.kwon@samsung.com
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b57177 ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is a set of small fixes for the Tegra clock driver.
-----BEGIN PGP SIGNATURE-----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=oT14
-----END PGP SIGNATURE-----
Merge tag 'for-5.10-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-fixes
Pull Tegra clk driver fixes from Thierry Reding:
This is a set of small fixes for the Tegra clock driver.
* tag 'for-5.10-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Fix missing prototype for tegra210_clk_register_emc()
clk: tegra: Always program PLL_E when enabled
clk: tegra: Capitalization fixes
This was likely overlooked while porting the driver upstream.
Reported-by: Pavel Dubrova <pashadubrova@gmail.com>
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200922120909.97203-1-konradybcio@gmail.com
Fixes: f2a76a2955 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk_rcg2_dp_determine_rate() function is used for the DP pixel clk.
This function should return the rate that can be achieved by the pixel
clk in 'struct clk_rate_request::rate' and match the logic similar to
what is seen in clk_rcg2_dp_set_rate(). But that isn't the case. Instead
the code merely bubbles the rate request up to the parent of the pixel
clk and doesn't try to do a rational approximation of the rate that
would be achieved by picking some m/n value for the RCG.
Let's change this logic so that we can assume the parent clk frequency
is fixed (it is because it's the VCO of the DP PLL that is configured
based on the link rate) and so that we can calculate what the m/n value
will be and adjust the req->rate appropriately.
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200916231202.3637932-10-swboyd@chromium.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This addresses the following gcc warning with "make W=1":
drivers/clk/qcom/gcc-msm8939.c:610:32: warning:
‘gcc_xo_gpll6_gpll0a_map’ defined but not used
[-Wunused-const-variable=]
static const struct parent_map gcc_xo_gpll6_gpll0a_map[] = {
^~~~~~~~~~~~~~~~~~~~~~~
drivers/clk/qcom/gcc-msm8939.c:598:32: warning: ‘gcc_xo_gpll6_gpll0_map’
defined but not used [-Wunused-const-variable=]
static const struct parent_map gcc_xo_gpll6_gpll0_map[] = {
^~~~~~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200911013722.1459387-1-yanaijie@huawei.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This addresses the following sparse warning:
drivers/clk/qcom/gcc-ipq8074.c:4325:17: warning: symbol
'pcie0_rchng_clk_src' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200921142750.875142-1-yanaijie@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
support CLK_OF_DECLARE and builtin_platform_driver_probe
double clk init method.
add module author, description and license to support building
Soc Rk3399 clock driver as module.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200914022316.24045-1-zhangqing@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
use CONFIG_COMMON_CLK_ROCKCHIP for Rk common clk drivers.
use CONFIG_CLK_RKXX for Rk soc clk driver.
Mark CONFIG_CLK_RK3399 to "tristate",
to support building Rk3399 SoC clock driver as module.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200914022304.23908-1-zhangqing@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is used by the Rockchip clk driver, export it to allow that
driver to be compiled as a module.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200914022225.23613-5-zhangqing@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is used by the Rockchip clk driver, export it to allow that
driver to be compiled as a module..
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200914022225.23613-4-zhangqing@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is used by the Rockchip clk driver, export it to allow that
driver to be compiled as a module..
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200914022225.23613-3-zhangqing@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The parent names 'mux_timer_src_p' is not used:
In file included from drivers/clk/rockchip/clk-rk3308.c:13:0:
drivers/clk/rockchip/clk-rk3308.c:136:7: warning: ‘mux_timer_src_p’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200916161740.14173-6-krzk@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As i.MX21 support has been removed, get rid of its clock driver too.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx35_clocks_init() has been used to register clocks on i.MX35
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx35_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx31_clocks_init() has been used to register clocks on i.MX31
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx31_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx27_clocks_init() has been used to register clocks on i.MX27
non-devicetree platforms.
Now that i.MX is a devicetree-only platform, it is safe to
remove mx27_clocks_init() as there are no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Include the Tegra driver's clk.h to pull in the prototype definition for
this function so that compilers don't warn about it being missing.
Fixes: 0ac65fc946 ("clk: tegra: Implement Tegra210 EMC clock")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
added checks to avoid enabling PLLs that have already been enabled by
the bootloader. However, the PLL_E configuration inherited from the
bootloader isn't necessarily the one that is needed for the kernel.
This can cause SATA to fail like this:
[ 5.310270] phy phy-sata.6: phy poweron failed --> -110
[ 5.315604] tegra-ahci 70027000.sata: failed to power on AHCI controller: -110
[ 5.323022] tegra-ahci: probe of 70027000.sata failed with error -110
Fix this by always programming the PLL_E. This ensures that any mis-
configuration by the bootloader will be overwritten by the kernel.
Fixes: bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
Reported-by: LABBE Corentin <clabbe@baylibre.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The rcar-gen3-cpg driver is also used on Renesas RZ/G2 SoC's, update the
description for the CLK_RCAR_GEN3_CPG config symbol to reflect this.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200911101703.20521-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Initial support for R-Car V3U (r8a779a0), including core, module
clocks, resets, and register access, because register specification
differs from R-Car Gen2/3.
Inspired by patches in the BSP by LUU HOAI.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1599810232-29035-4-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To support other register layouts in the future, add register pointers
of {control,status,reset,reset_clear}_regs into struct cpg_mssr_priv.
After that, we can remove unused macros like MSTPSR(). No behavioral
changes.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1599810232-29035-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
For the CPU clock registration two parent clocks are required, these
are now being passed as struct clk_hw pointers, rather than by the
global scope names. That allows us to avoid __clk_lookup() calls
and simplifies a bit the CPU clock registration function.
While at it drop unneeded extern keyword in the function declaration.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20200826171529.23618-3-s.nawrocki@samsung.com
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use non-zero clock IDs in definitions of the CPU parent clocks
for exynos5420, exynos5250 SoCs. This will allow us to reference
the parent clocks directly in the driver by cached struct clk_hw
pointers, rather than doing clk lookup by name.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20200826171529.23618-2-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds a clk ID to the mout_sw_aclk_g3d clk definition so related
clk pointer gets cached in the driver's private data and can be used
later instead of a __clk_lookup() call.
With that we have all clocks used in the clk_prepare_enable() calls in the
clk provider init callback cached in clk_data.hws[] and we can reference
the clk pointers directly rather than using __clk_lookup() with global names.
Link: https://lore.kernel.org/r/20200811151251.31613-2-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
- fix for a regression in v5.9-rc1 on Odroid XU3/XU4, i.e. booting
failure due to the DRAM controller root clock being disabled
-----BEGIN PGP SIGNATURE-----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=dCrJ
-----END PGP SIGNATURE-----
Merge tag 'v5.9-clk-samsung-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-fixes
Pull a Samsung clk driver fix from Sylwester Nawrocki:
- fix for a regression in v5.9-rc1 on Odroid XU3/XU4, i.e. booting
failure due to the DRAM controller root clock being disabled
* tag 'v5.9-clk-samsung-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: Keep top BPLL mux on Exynos542x enabled
BPLL clock must not be disabled because it is needed for proper DRAM
operation. This is normally handled by respective memory devfreq driver,
but when that driver is not yet probed or its probe has been deferred
the clock might get disabled what causes board hang. Fix this by calling
clk_prepare_enable() directly from the clock provider driver.
Cc: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200807133143.22748-1-m.szyprowski@samsung.com
Fixes: 6e7674c3c6 ("memory: Add DMC driver for Exynos5422")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
A few words were misspelled in this comment.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lpass_core_sc7180_probe() misses to call pm_clk_destroy() and
pm_runtime_disable() in error paths. Correct goto target to fix it.
This issue is found by code inspection.
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Link: https://lore.kernel.org/r/20200827141629.101802-1-jingxiangfeng@huawei.com
Fixes: edab812d80 ("clk: qcom: lpass: Add support for LPASS clock controller for SC7180")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the necessary bits so unnecessary amlogic clock controllers can be
compiled out. This allows to save a few kB when necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200828154735.435374-1-jbrunet@baylibre.com
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control is
transferred from the middle of the loop, as in the case of a return
or break or goto, there is no decrement thus ultimately resulting in
a memory leak.
Fix a potential memory leak in clk-impd1.c by inserting
of_node_put() before a return statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Link: https://lore.kernel.org/r/20200829175704.GA10998@Kaladin
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The DVP driver depends both on the RESET_SIMPLE driver but also on the
reset framework itself. Let's make sure we have it enabled.
Fixes: 1bc9597271 ("clk: bcm: Add BCM2711 DVP driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200903082636.3844629-1-maxime@cerno.tech
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix and add missing kerneldoc to fix compile warnings like:
drivers/clk/imx/clk-pfd.c:27: warning: Function parameter or member 'hw' not described in 'clk_pfd'
drivers/clk/imx/clk-pllv3.c:53: warning: Function parameter or member 'ref_clock' not described in 'clk_pllv3'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, Page 574, Chapter 5.2.6.4.3 Peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to RM, for peripheral clock slice,
"IP clock slices must be stopped to change the clock source.".
So we must have CLK_SET_PARENT_GATE flag to avoid glitch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VSP1 instances VSPS (which stands for "VSP Standard") and VSPR (which
stands for "VSP for Resizing") were wrongly named as "vsp1-sy" and
"vsp1-rt". The clock section in the SoC datasheets misunderstood the
abbreviations as meaning VSP System and VSP Realtime, and named the
corresponding clocks VSP1(SY) and VSP1(RT). This mistake has been
carried over to the kernel code.
This patch fixes this by renaming the clock names to "vsps" and "vspr".
Inspired from commit 79ea9934b8 ("ARM: shmobile: r8a7790: Rename
VSP1_(SY|RT) clocks to VSP1_(S|R)")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20200831183722.8165-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock entry 130 for VSPR (VSP for Resizing) module, so that this module
can be used on R8A7742 (RZ/G1H) SoC.
Alongside rename clock entry "vsp1-sy" to "vsps" (VSP Standard), so that
VSP1 clock names are in sync.
Note: The entry for VSPR clock was accidentally dropped from RZ/G manual
when all the information related to RT were removed.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200831180312.7453-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The root clock slice at offset 0xbf80 should be memrepair
clock, so correct it. And this clock should be always on
to make sure the memory repair function can works well.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The root clock slice at 0xbf00 is media_ldb clock,
not csi_phy2_ref, so correct it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On Amlogic Meson G12b platform, similar to fclk_div3, the fclk_div2
seems to be necessary for the system to operate correctly as well.
Typically, the clock also gets chosen by the eMMC peripheral. This
probably masked the problem so far. However, when booting from a SD
card the clock seems to get disabled which leads to a system freeze.
Let's mark this clock as critical, fixing boot from SD card on G12b
platforms.
Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/577e0129e8ee93972d92f13187ff4e4286182f67.1598629915.git.stefan@agner.ch
Audio cores need specific clock rates which can't be simply obtained by
adjusting integer multipliers and dividers. HW for such cases supports
delta-sigma modulation which enables fractional multipliers.
Port H3 delta-sigma table to R40. They have identical audio PLLs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200825131049.1277596-1-jernej.skrabec@siol.net
Add the clock for CRC block allowing it to be enabled by consumers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description and
license to support building i.MX8QXP clock drivers as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change configuration to "tristate", add module author, description
and license to support building i.MX8M SoCs clock driver as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add CONFIG_CLK_xxx for i.MX ARMv7 platforms, and use it as build option
instead of CONFIG_SOC_xxx, the CONFIG_CLK_xxx will be selected by default
according to CONFIG_SOC_xxx.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are more and more requirements of building SoC specific drivers
as modules, add support for building i.MX common clock driver as module
to meet the requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Export clk_hw_register_composite() to support user built as module.
ERROR: modpost: "clk_hw_register_composite" [drivers/clk/imx/mxc-clk.ko]
undefined!
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use readl_relaxed() instead of __raw_readl(), and use BIT(x)
instead of (1 << X) to fix below build warning reported by kernel
test robot:
drivers/clk/imx/clk-imx6sl.c:149:49: warning: Shifting signed 32-bit
value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
while (!(__raw_readl(anatop_base + PLL_ARM) & BM_PLL_ARM_LOCK))
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Passing pointers directly as platform data is fragile and undocumented.
Better to create a platform data structure which explicitly documents
what is passed to the driver.
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-6-krzk@kernel.org
The clk driver uses both a function call into an exported
platform file and a direct register access to a hardcoded
virtual address for accessing the MISCCR register, both
become are a problem for a multiplatform kernel because
of the header file dependency.
Make this an indirect function call through platform data
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-5-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A new warning in Clang points out that the initialization of
mux_pll_src_4plls_p appears incorrect:
../drivers/clk/rockchip/clk-rk3228.c:140:58: warning: suspicious
concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Wstring-concatenation]
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
,
../drivers/clk/rockchip/clk-rk3228.c:140:48: note: place parentheses
around the string literal to silence warning
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
1 warning generated.
Given the name of the variable and the same variable name in rv1108, it
seems that this should have been four distinct elements. Fix it up by
adding the comma as suggested.
Fixes: 307a2e9ac5 ("clk: rockchip: add clock controller for rk3228")
Link: https://github.com/ClangBuiltLinux/linux/issues/1123
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200810044020.2063350-1-natechancellor@gmail.com
Reviewed-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
'sizeof(*pllen)' should be used in place of 'sizeof(*pllout)' to avoid a
small over-allocation.
Fixes: 2d17269151 ("clk: davinci: New driver for davinci PLL clocks")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200809144959.747986-1-christophe.jaillet@wanadoo.fr
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The s3c2410_common_clk_init() and others are defined and used by the
clk-s3c24xx driver and also used in the mach-s3c24xx machine code. Move
the declaration to a header to fix W=1 build warnings:
drivers/clk/samsung/clk-s3c2410.c:320:13: warning: no previous prototype for 's3c2410_common_clk_init' [-Wmissing-prototypes]
320 | void __init s3c2410_common_clk_init(struct device_node *np, unsigned long xti_f,
drivers/clk/samsung/clk-s3c2412.c:205:13: warning: no previous prototype for 's3c2412_common_clk_init' [-Wmissing-prototypes]
205 | void __init s3c2412_common_clk_init(struct device_node *np, unsigned long xti_f,
drivers/clk/samsung/clk-s3c2443.c:341:13: warning: no previous prototype for 's3c2443_common_clk_init' [-Wmissing-prototypes]
341 | void __init s3c2443_common_clk_init(struct device_node *np, unsigned long xti_f,
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
The s3c64xx_clk_init() is defined and used by the clk-s3c64xx driver and
also used in the mach-s3c64xx machine code. Move the declaration to a
header to fix W=1 build warning:
drivers/clk/samsung/clk-s3c64xx.c:391:13: warning: no previous prototype for 's3c64xx_clk_init' [-Wmissing-prototypes]
391 | void __init s3c64xx_clk_init(struct device_node *np, unsigned long xtal_f,
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Fix the tdmout inverter of the g12a and following SoC families.
This inverter is special and needs two bits to be the inverse of each other
for the inverter to operate properly.
Fixes: 075001385c ("clk: meson: axg-audio: add g12a support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200729154359.1983085-4-jbrunet@baylibre.com
There are more differences than what we initially thought.
Let's keeps things clear and separate the axg and g12a regmap tables of the
audio clock controller.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200729154359.1983085-3-jbrunet@baylibre.com
This is yet another simple but odd driver for the audio block of the g12a
and sm1 SoC families.
For TDMOUT's sclk to be properly inverted, bit 29 of
AUDIO_CLK_TDMOUT_x_CTRL should be the inverse of bit 28.
IOW bit28 == !bit29 at all times
This setting is automatically applied on axg and the manual setting was
added on g12a.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200729154359.1983085-2-jbrunet@baylibre.com
Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
driver and the Designware i2c driver (changes from Akshu Agrawal and
Pu Wen).
-----BEGIN PGP SIGNATURE-----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=D9q+
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
driver and the Designware i2c driver (changes from Akshu Agrawal and
Pu Wen)"
* tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
clk: x86: Support RV architecture
ACPI: APD: Add a fmw property is_raven
clk: x86: Change name from ST to FCH
ACPI: APD: Change name from ST to FCH
i2c: designware: Add device HID for Hygon I2C controller
The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some types
of hardware can generate the full range of signals that they're capable
of. The remainder is mostly minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=v6MG
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
happened to tag the tree at an earlier point in the history of clk-next.
I must have fat fingered it and checked out an older version of clk-next
on this second computer I'm using.
This time it actually includes more code for Qualcomm SoCs, the AT91
major updates, and some Rockchip SoC clk driver updates as well. I've
corrected this flow so this shouldn't happen again.
-----BEGIN PGP SIGNATURE-----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=/8EM
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"Here's some more updates that missed the last pull request because I
happened to tag the tree at an earlier point in the history of
clk-next. I must have fat fingered it and checked out an older version
of clk-next on this second computer I'm using.
This time it actually includes more code for Qualcomm SoCs, the AT91
major updates, and some Rockchip SoC clk driver updates as well. I've
corrected this flow so this shouldn't happen again"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (83 commits)
clk: bcm2835: Do not use prediv with bcm2711's PLLs
clk: drop unused function __clk_get_flags
clk: hsdk: Fix bad dependency on IOMEM
dt-bindings: clock: Fix YAML schemas for LPASS clocks on SC7180
clk: mmp: avoid missing prototype warning
clk: sparx5: Add Sparx5 SoC DPLL clock driver
dt-bindings: clock: sparx5: Add bindings include file
clk: qoriq: add LS1021A core pll mux options
clk: clk-atlas6: fix return value check in atlas6_clk_init()
clk: tegra: pll: Improve PLLM enable-state detection
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
clk: qcom: gcc-sdm660: Fix up gcc_mss_mnoc_bimc_axi_clk
clk: qcom: gcc-sdm660: Add missing modem reset
...
framework we just have some minor tweaks and a debugfs feature, so not much to
see there. The driver updates are fairly well split between AT91 and Qualcomm
clk support. Adding those two drivers together equals about 50% of the
diffstat. Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks. See below for some more highlights.
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only consider
clocks that were enabled at boot time
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl8tspERHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSX0og//TXp134IBXVZ2Z5Wca4J41itv7tPGJFsX
EslQ/eMm6xhGEqqrA6BVsQ228JF9rUmg1fbvdl82UPK7Zyp9P2fo6CMC65ngDTky
B1rLZOaKitER9JdL9DmmnIR772pI//rAMdIeVC/Jn5RR7OpP4lgY6+qvK0pJjVFl
8aK3uHY+UWVFtqZxuJEAAyZBq1+bREqmVwNC1my6kmMIf0j0KwcGhrZgASWWtjQK
4TRmroehLC4FBqnJ78Y3E6UAOBlz6C7XnP38qJge2672Ef7QhXZU7AGrGiTtxc4h
5fB6MNMF+5QGel54qR1eH+JxaEoKsAjLaX1VBr7hAHrGIQ26dBFHFPsPvWDA+VVR
4bwXJKz2objAWyqlMVM/cVV3q6uDixuScdrw2aAiojmV7ZvdZXflacdmZuS5v7e4
sh86llN+lF0YrViYz33z+up0risCAi089xVo7Z99VgyLe2DR8TE+4/d6DQTFRNxl
m66m6mlB9pPPgIV028SAf/zmzyoVWEarwdEAQPjJC6KVRbnR9mFlhSiTQMmCsSvU
zHRxVcInc+8qIJY6VJ552UFu/JAan/AFl5knb+kW21a7hM8p81H9HuSnS4aHDDq4
yETPU3XSMYz8ARHX4lKo1UIB6+k9iF2CWdCP+gXHNP+QYSAsRBIJsonjul9lLUCi
8i6mUGkS0OU=
=QLRg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It looks like a smaller batch of clk updates this time around.
In the core framework we just have some minor tweaks and a debugfs
feature, so not much to see there. The driver updates are fairly well
split between AT91 and Qualcomm clk support. Adding those two drivers
together equals about 50% of the diffstat.
Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks.
Highlights:
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only
consider clocks that were enabled at boot time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (79 commits)
clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
ipq806x: gcc: add support for child probe
clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
clk: qcom: ipq8074: Add correct index for PCIe clocks
clk: <linux/clk-provider.h>: drop a duplicated word
clk: renesas: cpg-mssr: Add r8a774e1 support
dt-bindings: clock: renesas,cpg-mssr: Document r8a774e1
clk: Drop duplicate selection in Kconfig
clk: qcom: smd: Add support for MSM8992/4 rpm clocks
clk: qcom: ipq8074: Add missing clocks for pcie
dt-bindings: clock: qcom: ipq8074: Add missing bindings for PCIe
Replace HTTP links with HTTPS ones: Common CLK framework
clk: qcom: Add CPU clock driver for msm8996
dt-bindings: clk: qcom: Add bindings for CPU clock for msm8996
soc: qcom: Separate kryo l2 accessors from PMU driver
clk: meson: meson8b: add the vclk2_en gate clock
clk: meson: meson8b: add the vclk_en gate clock
clk: qcom: Fix return value check in apss_ipq6018_probe()
clk: bcm: dvp: Add missing module informations
clk: meson: meson8b: Drop CLK_IS_CRITICAL from fclk_div2
...
There is minor difference between previous family of SoC and
the current one. Which is the there is only 48Mh fixed clk.
There is no mux and no option to select another freq as there in previous.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
AMD SoC general pupose clk is present in new platforms with
minor differences. We can reuse the same clk driver for other
platforms. Hence, changing name from ST(SoC) to FCH(IP)
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
AMD SoC general pupose clk is present in new platforms with
same MMIO mappings. We can reuse the same clk handler support
for other platforms. Hence, changing name from ST(SoC) to FCH(IP)
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
- Add support for SAMA7G5 SoC clks
- Microchip Sparx5 DPLL clk
* clk-microchip:
clk: sparx5: Add Sparx5 SoC DPLL clock driver
dt-bindings: clock: sparx5: Add bindings include file
* clk-mmp:
clk: mmp: avoid missing prototype warning
* clk-unused:
clk: drop unused function __clk_get_flags
* clk-at91:
clk: at91: sama7g5: add clock support for sama7g5
clk: at91: clk-utmi: add utmi support for sama7g5
clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs
clk: at91: add macro for pll ids mask
clk: at91: clk-programmable: add mux_table option
clk: at91: clk-peripheral: add support for changeable parent rate
clk: at91: clk-master: add master clock support for SAMA7G5
clk: at91: clk-generated: add mux_table option
clk: at91: clk-generated: pass the id of changeable parent at registration
clk: at91: replace conditional operator with double logical not
clk: at91: sckc: register slow_rc with accuracy option
clk: at91: sam9x60: fix main rc oscillator frequency
clk: at91: sam9x60-pll: use frac when setting frequency
clk: at91: sam9x60-pll: check fcore against ranges
clk: at91: sam9x60-pll: use logical or for range check
clk: at91: clk-sam9x60-pll: fix mul mask
clk: at91: clk-generated: check best_rate against ranges
clk: at91: clk-generated: continue if __clk_determine_rate() returns error
clk: at91: fix possible dead lock in new drivers
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
* clk-fallthru:
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
* clk-ingenic:
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
* clk-tegra:
clk: tegra: pll: Improve PLLM enable-state detection
* clk-sirf:
clk: clk-atlas6: fix return value check in atlas6_clk_init()
* clk-qoriq:
clk: qoriq: add LS1021A core pll mux options
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Make defines for bcm63xx-gate clks to use in DT
- Support gate clks on BCM6318 SoCs
- Add HDMI clks for BCM2711 SoCs
- Support BCM2711 SoC firmware clks
* clk-socfpga:
clk: socfpga: agilex: mpu_l2ram_clk should be mpu_ccu_clk
clk: socfpga: agilex: add nand_x_clk and nand_ecc_clk
dt-bindings: agilex: add NAND_X_CLK and NAND_ECC_CLK
* clk-doc:
clk: Clean up kernel-doc errors
clk: <linux/clk-provider.h>: drop a duplicated word
clk: add function documentation for clk_hw_round_rate()
* clk-qcom: (38 commits)
dt-bindings: clock: Fix YAML schemas for LPASS clocks on SC7180
clk: qcom: gcc-sdm660: Fix up gcc_mss_mnoc_bimc_axi_clk
clk: qcom: gcc-sdm660: Add missing modem reset
clk: qcom: lpass: Add support for LPASS clock controller for SC7180
clk: qcom: gcc: Add support for GCC LPASS clock for SC7180
dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7180
clk: qcom: gdsc: Add support to enable retention of GSDCR
clk: qcom: Export gdsc_gx_do_nothing_enable() to modules
clk: qcom: Add graphics clock controller driver for SM8250
clk: qcom: Add graphics clock controller driver for SM8150
clk: qcom: add common gdsc_gx_do_nothing_enable for gpucc drivers
dt-bindings: clock: add SM8250 QCOM Graphics clock bindings
dt-bindings: clock: add SM8150 QCOM Graphics clock bindings
dt-bindings: clock: combine qcom,sdm845-gpucc and qcom,sc7180-gpucc
clk: qcom: gcc: remove unnecessary vco_table from SM8150
clk: qcom: clk-alpha-pll: use the right PCAL_DONE value for lucid pll
clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid
clk: qcom: clk-alpha-pll: remove unused/incorrect PLL_CAL_VAL
clk: qcom: gcc: fix sm8150 GPU and NPU clocks
dt-bindings: clock: Fix qcom,msm8996-apcc yaml syntax
...
* clk-vc5:
clk: vc5: use a dedicated struct to describe the output drivers
dt-bindings: clk: versaclock5: convert to yaml
MAINTAINERS: take over IDT VersaClock 5 clock driver
dt-bindings: clk: versaclock5: fix 'idt' prefix typos
clk: vc5: Add memory check to prevent oops
clk: vc5: fix use of memory after it has been kfree'd
clk: vc5: Enable addition output configurations of the Versaclock
dt: Add additional option bindings for IDT VersaClock
clk: vc5: Allow Versaclock driver to support multiple instances
* clk-bcm: (44 commits)
clk: bcm2835: Do not use prediv with bcm2711's PLLs
dt-bindings: arm: bcm: Add a select to the RPI Firmware binding
clk: bcm: dvp: Add missing module informations
clk: bcm: rpi: Remove the quirks for the CPU clock
clk: bcm2835: Don't cache the PLLB rate
clk: bcm2835: Allow custom CCF flags for the PLLs
Revert "clk: bcm2835: remove pllb"
clk: bcm: rpi: Give firmware clocks a name
clk: bcm: rpi: Discover the firmware clocks
clk: bcm: rpi: Add an enum for the firmware clocks
clk: bcm: rpi: Add DT provider for the clocks
clk: bcm: rpi: Make the PLLB registration function return a clk_hw
clk: bcm: rpi: Split pllb clock hooks
clk: bcm: rpi: Rename is_prepared function
clk: bcm: rpi: Pass the clocks data to the firmware function
clk: bcm: rpi: Add clock id to data
clk: bcm: rpi: Create a data structure for the clocks
clk: bcm: rpi: Use CCF boundaries instead of rolling our own
clk: bcm: rpi: Make sure the clkdev lookup is removed
clk: bcm: rpi: Switch to clk_hw_register_clkdev
...
Contrary to previous SoCs, bcm2711 doesn't have a prescaler in the PLL
feedback loop. Bypass it by zeroing fb_prediv_mask when running on
bcm2711.
Note that, since the prediv configuration bits were re-purposed, this
was triggering miscalculations on all clocks hanging from the VPU clock,
notably the aux UART, making its output unintelligible.
Fixes: 42de9ad400 ("clk: bcm2835: Add BCM2711_CLOCK_EMMC2 support")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200730182619.23246-1-nsaenzjulienne@suse.de
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The function __clk_get_flags has not been used since the April 2019
commit a348f05361 ("ARM: omap2+: hwmod: drop CLK_IS_BASIC
flag usage"). Other uses were removed in June 2015, eg by
commit 98d8a60ecc ("clk: Convert __clk_get_flags() to
clk_hw_get_flags()"), which shows how clk_hw_get_flags can easily
be used instead.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1596272022-14173-1-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CONFIG_IOMEM does not exist. The correct symbol to depend on is
CONFIG_HAS_IOMEM.
Fixes: 1e7468bd9d ("clk: Specify IOMEM dependency for HSDK pll driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200803084835.21838-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Need to merge this up to get the IOMEM dependency patch on top that is
broken and fixed in the next commit.
* clk-fixes:
clk: Specify IOMEM dependency for HSDK pll driver
clk: AST2600: Add mux for EMMC clock
clk: mvebu: ARMADA_AP_CPU_CLK needs to select ARMADA_AP_CP_HELPER
The kernel test robot points out two harmless warnings in the
mmp clk drivers:
drivers/clk/mmp/clk-pxa168.c:68:13: warning: no previous prototype for 'pxa168_clk_init' [-Wmissing-prototypes]
drivers/clk/mmp/clk-pxa910.c:66:13: warning: no previous prototype for 'pxa910_clk_init' [-Wmissing-prototypes]
Fix these by including corresponding header file.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200729113456.4072290-1-arnd@arndb.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This allows to clock the cores with 1 GHz, 500 MHz and 250 MHz.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200610113837.27117-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200713032143.21362-1-vulab@iscas.ac.cn
Acked-by: Barry Song <baohua@kernel.org>
Fixes: 7bf21bc81f ("clk: sirf: re-arch to make the codes support both prima2 and atlas6")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Power Management Controller (PMC) can override the PLLM clock settings,
including the enable-state. Although PMC could only act as a second level
gate, meaning that PLLM needs to be enabled by the Clock and Reset
Controller (CaR) anyways if we want it to be enabled. Hence, when PLLM is
overridden by PMC, it needs to be enabled by CaR and ungated by PMC in
order to be functional. Please note that this patch doesn't fix any known
problem, and thus, it's merely a minor improvement.
Link: https://lore.kernel.org/linux-arm-kernel/20191210120909.GA2703785@ulmo/T/
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200709172057.13951-1-digetx@gmail.com
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add functions for calculat the rate of REFCLK, which is needed by
USB PHY in Ingenic X1000 SoC.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-4-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Reformat the code (add one level of indentation before the values),
to align the code in the macro definition section.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new functions to "jz4780_otg_phy_ops" to enable or disable the
USB PHY in the JZ4780 SoC.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The RTC unit in the Ingenic SoCs has two clock sources, one
is from an external 32.768kHz clock, and the other is from an
external 24MHz/48MHz main clock that is divided by 512. The
choice of these two clocks is controlled by the ERCS bit in
the OPCR register. The RNG unit will also use this clock.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200725051136.58220-4-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add missing halt_check, hwcg_reg and hwcg_bit properties.
These were likely omitted when porting the driver upstream.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200726111215.22361-9-konradybcio@gmail.com
Fixes: f2a76a2955 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This will be required in order to support the
modem upstream.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200726111215.22361-2-konradybcio@gmail.com
Fixes: f2a76a2955 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Low Power Audio subsystem clocks are required for Audio client
to be able to request for the clocks and power domains.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1595606878-2664-5-git-send-email-tdas@codeaurora.org
[sboyd@kernel.org: Drop unused ret in probe function]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the RETAIN_FF_ENABLE feature which enables the
usage of retention registers. These registers maintain their
state after disabling and re-enabling a GDSC.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1595606878-2664-2-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Douglas Anderson
Krzysztof Kozlowski
Geert Uytterhoeven
Lad Prabhakar
Yejune Deng
Biju Das
Jacopo Mondi
Arnd Bergmann
Manivannan Sadhasivam
Naveen Yadav
Michael Walle
Dong Aisheng
Johan Jonker
Xu Wang
Colin Ian King
Sivaram Nair
Neil Armstrong
Thara Gopinath
Sylwester Nawrocki
Kevin Hilman
Nicolin Chen
Tony Lindgren
Dmitry Baryshkov
Jerome Brunet
Lukas Bulwahn
Stephen Boyd
Dan Carpenter
Zou Wei
Dmitry Osipenko
Srinivas Kandagatla
Taniya Das
Peng Fan
Abel Vesa
Tom Rix
Robin Murphy
Wolfram Sang
Joe Perches
Linus Torvalds
Claudiu Beznea
Paul Cercueil
Navid Emamdoost
Lubomir Rintel
Rikard Falkeborn
Serge Semin
Zhao Qiang
Lars-Peter Clausen
Jonathan Marek
Konrad Dybcio
Julia Lawall
Wang Qing
Fabien Parent
Hanks Chen
Olof Johansson
Tero Kristo
Liu Shixin
Dinh Nguyen
YueHaibing
Hoegeun Kwon
Marek Szyprowski
Stephen Boyd
Jason Yan
Elaine Zhang
Fabio Estevam
Thierry Reding
Yoshihiro Shimoda
Jonathan Neuschäfer
Jing Xiangfeng
Sumera Priyadarsini
Maxime Ripard
Jacky Bai
Stefan Agner
Jernej Skrabec
Yangtao Li
Anson Huang
Nathan Chancellor
Christophe JAILLET
Akshu Agrawal
Nicolas Saenz Julienne
Lars Povlsen
Michael Krummsdorf
周琰杰 (Zhou Yanjie)
Gustavo A. R. Silva