The device-managed allocation API doesn't work well with the life-cycle
of device objects. Since ports have device objects allocated within, it
can lead to situations where these devices need to stay around until
after their parent pad controller has been unbound from its driver. The
device-managed memory allocated for the port objects will, however, get
freed when the pad controller unbinds from the driver. This can cause
use-after-free errors down the road.
Note that the device is deleted as part of the driver unbind operation,
so there isn't much that can be done with it after that point, but the
memory still needs to stay around to ensure none of the references are
invalidated.
One situation where this arises is when a VBUS supply is associated with
a USB 2 or 3 port. When that supply is released using regulator_put() an
SRCU call will queue the release of the device link connecting the port
and the regulator after a grace period. This means that the regulator is
going to keep on to the last reference of the port device even after the
pad controller driver was unbound (which is when the memory backing the
port device is freed).
Fix this by allocating port objects using non-device-managed memory. Add
release callbacks for these objects so that their memory gets freed when
the last reference goes away. This decouples the port devices' lifetime
from the "active" lifetime of the pad controller (i.e. the time during
which the pad controller driver owns the device).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Devices are created for each port of the XUSB pad controller. Each USB 2
and USB 3 port can potentially have an associated VBUS power supply that
needs to be removed when the device is removed.
Since port devices never bind to a driver, the driver core will not get
to perform the cleanup of device-managed resources that usually happens
on driver unbind.
Now, the driver core will also perform device-managed resource cleanup
for driver-less devices when they are released. However, when a device
link is created between the regulator and the port device, as part of
regulator_get(), the regulator takes a reference to the port device and
prevents it from being released unless regulator_put() is called, which
will never happen.
Avoid this by using the non-device-managed API and manually releasing
the regulator reference when the port is unregistered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Deferred probe is an expected return value for tegra_fuse_readl().
Given that the driver deals with it properly, there's no need to
output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As xusb-tegra186.c will be reused for Tegra194, it would be good to
protect Tegra186 soc data with CONFIG_ARCH_TEGRA_186_SOC. This commit
also reshuffles Tegra186 soc data single CONFIG_ARCH_TEGRA_186_SOC
will be sufficient.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on UTMI phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.
Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Thierry Reding
Jon Hunter
JC Kuo
Nagarjuna Kristam