If the regulatory database is loaded, and then updated, it may
be necessary to reload it. Add an nl80211 command to do this.
Note that this just reloads the database, it doesn't re-apply
the rules from it immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the current regulatory database is only about 4k big, and already
difficult to extend, we decided that overall it would be better to
get rid of the complications with CRDA and load the database into the
kernel directly, but in a new format that is extensible.
The new file format can be extended since it carries a length field
on all the structs that need to be extensible.
In order to be able to request firmware when the module initializes,
move cfg80211 from subsys_initcall() to the later fs_initcall(); the
firmware loader is at the same level but linked earlier, so it can
be called from there. Otherwise, when both the firmware loader and
cfg80211 are built-in, the request will crash the kernel. We also
need to be before device_initcall() so that cfg80211 is available
for devices when they initialize.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merging this brings in the timer_setup() change, which allows
me to apply Kees's mac80211 changes for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an event that indicates that a connection is authorized
(i.e. the 4 way handshake was performed by the driver). This event
should be sent by the driver after sending a connect/roamed event.
This is useful for networks that require 802.1X authentication.
In cases that the driver supports 4 way handshake offload, but the
802.1X authentication is managed by user space, the driver needs to
inform user space right after the 802.11 association was completed
so user space can initialize its 802.1X state machine etc.
However, it is also possible that the AP will choose to skip the
802.1X authentication (e.g. when PMKSA caching is used) and proceed
with the 4 way handshake immediately. In this case the driver needs
to inform user space that 802.1X authentication is no longer required
(e.g. to prevent user space from disconnecting since it did not get
any EAPOLs from the AP).
This is also useful for roaming, in which case it is possible that
the driver used the Fast Transition protocol so 802.1X is not
required.
Since there will now be a dedicated notification indicating that the
connection is authorized, the authorized flag can be removed from the
roamed event. Drivers can send the new port authorized event right
after sending the roamed event to indicate the new AP is already
authorized. This therefore reserves the old PORT_AUTHORIZED attribute.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to IEEE Std 802.11-2016 (16.2.3.4 Long PHY SIGNAL field) all of
the following rates are mandatory for a HR/DSSS PHY: 1 Mb/s, 2 Mb/s,
5.5 Mb/s and 11 Mb/s. Set IEEE80211_RATE_MANDATORY_B flag for all of these
instead of just 1 Mb/s to correctly reflect this.
Signed-off-by: Richard Schütz <rschuetz@uni-koblenz.de>
[johannes: use switch statement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The user space can now allow the kernel to associate to an AP that
requires MFP or that doesn't have MFP enabled in the same
NL80211_CMD_CONNECT command, by using a new NL80211_MFP_OPTIONAL flag.
The driver / firmware will decide whether to use it or not.
Include a feature bit to advertise support for NL80211_MFP_OPTIONAL.
This allows new user space to run on old kernels and know that it
cannot use the new attribute if it isn't supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function hasn't been used since the removal of iwmc3200wifi
in 2012. It also appears to have a bug when qos=True, since then
it'll copy uninitialized stack memory to the SKB.
Just remove the function entirely.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add Optimized Connectivity Experience (OCE) scan and capability flags.
Some of them unique to OCE and some are stand alone.
And add scan flags to enable/disable them.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When NL80211_ATTR_WIPHY_CHANNEL_TYPE is given, nl80211 would parse the
channel definition the old way, discarding NL80211_ATTR_CENTER_FREQ1,
NL80211_ATTR_CENTER_FREQ2 etc. However, it is possible that user space
added both NL80211_ATTR_WIPHY_CHANNEL_TYPE and NL80211_ATTR_CENTER_FREQ1
or NL80211_ATTR_CENTER_FREQ2 assuming that all settings would be honored.
In such a case, validate that NL80211_ATTR_CENTER_FREQ1 and
NL80211_ATTR_CENTER_FREQ2 values match the channel configuration,
as otherwise user space would assume that the desired configuration was
applied.
For example, when trying to start ap with
NL80211_ATTR_WIPHY_CHANNEL_TYPE = NL80211_CHAN_HT40MINUS,
NL80211_ATTR_WIPHY_FREQ = 5180 and NL80211_ATTR_CENTER_FREQ1 = 5250
without this fix, the ap will start on channel 36 (center_freq1 will be
corrected to 5180). With this fix, we will throw an error instead.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current ieee80211_ie_split() implementation doesn't
account for elements that are sub-elements of the
EXTENSION IE. To extend support to these IEs as well,
treat the WLAN_EID_EXTENSION ids in the %ids array
as indicating that the next id in the array is a
sub-element of the EXTENSION IE.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If TX rates are specified during mesh join, the channel must
also be specified. Check the channel pointer to avoid a null
pointer dereference if it isn't.
Reported-by: Jouni Malinen <j@w1.fi>
Fixes: 8564e38206 ("cfg80211: add checks for beacon rate, extend to mesh")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211_set_rekey_data() does not check if the required attributes
NL80211_REKEY_DATA_{REPLAY_CTR,KEK,KCK} are present when processing
NL80211_CMD_SET_REKEY_OFFLOAD request. This request can be issued by
users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attributes presence.
This patch is based on the patch by bo Zhang.
This fixes CVE-2017-12153.
References: https://bugzilla.redhat.com/show_bug.cgi?id=1491046
Fixes: e5497d766a ("cfg80211/nl80211: support GTK rekey offload")
Cc: <stable@vger.kernel.org> # v3.1-rc1
Reported-by: bo Zhang <zhangbo5891001@gmail.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Honor the NL80211_RRF_NO_HT40{MINUS,PLUS} flags in
reg_process_ht_flags_channel. Not doing so leads can lead
to a firmware assert in iwlwifi for example.
Fixes: b0d7aa5959 ("cfg80211: allow wiphy specific regdomain management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no HT/VHT capabilities in cfg80211_ap_settings::beacon_ies,
these should be looked for in beacon's tail instead.
Fixes: 66cd794e3c ("nl80211: add HT/VHT capabilities to AP parameters")
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----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=I8Qv
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-07-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
pull-request: mac80211 2017-07-07
Just got a set of fixes in from Jouni/QCA, all netlink validation
fixes. I assume they ran some kind of checker, but I don't know what
kind :)
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
validate_scan_freqs() retrieves frequencies from attributes
nested in the attribute NL80211_ATTR_SCAN_FREQUENCIES with
nla_get_u32(), which reads 4 bytes from each attribute
without validating the size of data received. Attributes
nested in NL80211_ATTR_SCAN_FREQUENCIES don't have an nla policy.
Validate size of each attribute before parsing to avoid potential buffer
overread.
Fixes: 2a51931192 ("cfg80211/nl80211: scanning (and mac80211 update to use it)")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Buffer overread may happen as nl80211_set_station() reads 4 bytes
from the attribute NL80211_ATTR_LOCAL_MESH_POWER_MODE without
validating the size of data received when userspace sends less
than 4 bytes of data with NL80211_ATTR_LOCAL_MESH_POWER_MODE.
Define nla_policy for NL80211_ATTR_LOCAL_MESH_POWER_MODE to avoid
the buffer overread.
Fixes: 3b1c5a5307 ("{cfg,nl}80211: mesh power mode primitives and userspace access")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nla policy checks for only maximum length of the attribute data when the
attribute type is NLA_BINARY. If userspace sends less data than
specified, cfg80211 may access illegal memory. When type is NLA_UNSPEC,
nla policy check ensures that userspace sends minimum specified length
number of bytes.
Remove type assignment to NLA_BINARY from nla_policy of
NL80211_NAN_FUNC_SERVICE_ID to make these NLA_UNSPEC and to make sure
minimum NL80211_NAN_FUNC_SERVICE_ID_LEN bytes are received from
userspace with NL80211_NAN_FUNC_SERVICE_ID.
Fixes: a442b761b2 ("cfg80211: add add_nan_func / del_nan_func")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nla policy checks for only maximum length of the attribute data
when the attribute type is NLA_BINARY. If userspace sends less
data than specified, the wireless drivers may access illegal
memory. When type is NLA_UNSPEC, nla policy check ensures that
userspace sends minimum specified length number of bytes.
Remove type assignment to NLA_BINARY from nla_policy of
NL80211_ATTR_PMKID to make this NLA_UNSPEC and to make sure minimum
WLAN_PMKID_LEN bytes are received from userspace with
NL80211_ATTR_PMKID.
Fixes: 67fbb16be6 ("nl80211: PMKSA caching support")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If NAN interface is created with NL80211_ATTR_SOCKET_OWNER, the socket
that is used to create the interface is used for all NAN operations and
reporting NAN events.
However, it turns out that sending commands and receiving events on
the same socket is not possible in a completely race-free way:
If the socket buffer is overflowed by the events, the command response
will not be sent. In that case the caller will block forever on recv.
Using non-blocking socket for commands is more complicated and still
the command response or ack may not be received.
So, keep unicasting NAN events to the interface creator, but allow
using a different socket for commands.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, struct iwreq isn't a proper subset of struct ifreq,
but is still handled by the same code path. Robert reported that
then applications may (randomly) fault if the struct iwreq they
pass happens to land within 8 bytes of the end of a mapping (the
struct is only 32 bytes, vs. struct ifreq's 40 bytes).
To fix this, pull out the code handling wireless extension ioctls
and copy only the smaller structure in this case.
This bug goes back a long time, I tracked that it was introduced
into mainline in 2.1.15, over 20 years ago!
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195869
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make it clear that we never use struct ifreq, cast from it
directly in the wext entrypoint and use struct iwreq from there
on. The next patch will remove the cast again and pass the
correct struct from the beginning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no longer any drivers (in the tree proper, I didn't
check all the staging drivers) that take WEXT ioctls through
this API, the only remaining ones that even have ndo_do_ioctl
are using it only for private ioctls.
Therefore, we can remove this call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that initiate roaming while being connected to a network that
uses 802.1X authentication need to inform user space if 802.1X
authentication is further required after roaming.
For example, when using the Fast transition protocol, roaming within
the mobility domain does not require new 802.1X authentication, but
roaming to another mobility domain does.
In addition, some drivers may not support 802.1X authentication
(so it has to be done in user space), while other drivers do.
Add a flag to the roaming notification to indicate if user space is
required to do 802.1X authentication after the roaming or not.
This flag will only be used for networks that use 802.1X
authentication. For networks that do not use 802.1X authentication it
is assumed that no further action is required from user space after
the roaming notification.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com reuse NL80211_ATTR_PORT_AUTHORIZED]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[rebase to apply w/o the flag in CONNECT]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API for setting the PMK to the driver. For FT support, allow
setting also the PMK-R0 Name.
This can be used by drivers that support 4-Way handshake offload
while IEEE802.1X authentication is managed by upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[arend.vanspriel@broadcom.com: add WANT_1X_4WAY_HS attribute]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X docs a bit to
say that the device may require it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let drivers advertise support for station-mode 4-way handshake
offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK flag.
Extend use of NL80211_ATTR_PMK attribute indicating it might be passed
as part of NL80211_CMD_CONNECT command, and contain the PSK (which is
the PMK, hence the name.)
The driver/device is assumed to handle the 4-way handshake by
itself in this case (including key derivations, etc.), instead
of relying on the supplicant.
This patch is somewhat based on this one (by Vladimir Kondratiev):
https://patchwork.kernel.org/patch/1309561/.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com rebase dealing with existing ATTR_PMK]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK docs to indicate
that this offload might be required]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This brings in commit 7a7c0a6438 ("mac80211: fix TX aggregation
start/stop callback race") to allow the follow-up cleanup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the case the channel should be switched to one requiring DFS we need
to make sure that userspace will handle radar events when they happen.
For AP mode this is assumed to be the case, as a manager like hostapd
is required. However IBSS and MESH modes can work without further
userspace assistance, so refuse to use DFS channels unless userspace
vouches that it handles DFS.
NOTE: Userspace should have already flagged support earlier during mesh
or IBSS setup. However, this information is not readily accessible
currently.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
[sw: style cleanups]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When joining a mesh network it is not guaranteed that userspace has a
daemon listening for radar events. This is however required for channels
requiring DFS. To flag that userspace will handle radar events, it needs
to set NL80211_ATTR_HANDLE_DFS.
This matches the current mechanism used for IBSS mode.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus reported hitting the bandwidth warning, but it is indeed
pretty useless - improve it by printing the rate configuration
and make it only warn once, for both warnings here.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh forwarding path checks for address extension mode to fetch
appropriate proxied address and MPP address. Existing condition
that looks for 6 address format is not strict enough so that
frames with improper values are processed and invalid entries
are added into MPP table. Fix that by adding a stricter check before
processing the packet.
Per IEEE Std 802.11s-2011 spec. Table 7-6g1 lists address extension
mode 0x3 as reserved one. And also Table Table 9-13 does not specify
0x3 as valid address field.
Fixes: 9b395bc3be ("mac80211: verify that skb data is present")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since groups 0 and 63 are invalid, we should check for those bits.
Note that the 802.11 spec specifies the *bit* order, but the CPU
doesn't care about bit order since it can't address bits, so it's
always treating BIT(0) as the lowest bit within a byte.
Reported-by: Jan Fuchs <jan.fuchs@lancom.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.
Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch allows for the scheduled scan request to specify matchsets
for specific BSSIDs.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[docs, netlink policy fix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to allocate a portid structure and then, for
each of those, walk the interfaces - we can just add a flag
to each interface and walk those directly. Due to padding in
the struct, we can even do it without any memory cost, and
it even simplifies the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When part of a bigger bandwidth (160 MHz) channel falls in DFS
channel range it is possible that the center frequency may not
necessarily be a radar channel. Remove the sanity check on channel
flag for IEEE80211_CHAN_RADAR in regulatory_propagate_dfs_state(),
this should fix the dfs state propagation for non-DFS center freq
which has DFS channels in it's bandwidth, should also fix unnecessary
WARN_ON() spam in regulatory_propagate_dfs_state().
Fixes: 8976672736 ("cfg80211: Share Channel DFS state across wiphys of same DFS domain")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rate_flg is of type 'enum nl80211_attrs', however it is assigned with
'enum nl80211_rate_info' values. Change the type of rate_flg accordingly.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__ieee80211_amsdu_copy_frag intentionally initializes a pointer to
array[-1] to increment it later to valid values. clang rightfully
generates an array-bounds warning on the initialization statement.
Initialize the pointer to array[0] and change the algorithm from
increment before to increment after consume.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-scheduled scan support in subsequent patch a request id
will be added. This patch add this request id to the scheduled
scan event messages. For now the request id will always be zero.
With multi-scheduled scan its value will inform user-space to which
scan the event relates.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the parsing of monitor flags and the MU-MIMO options.
This will allow adding more things cleanly in the future and
also allows setting the latter already when creating a monitor
interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg
Avraham Stern
Richard Schütz
Emmanuel Grumbach
Roee Zamir
Tova Mussai
Liad Kaufman
Vladis Dronov
Igor Mitsyanko
David S. Miller
Srinivas Dasari
Andrei Otcheretianski
Eliad Peller
Arend Van Spriel
Benjamin Berg
Rajkumar Manoharan
Vasanthakumar Thiagarajan
Matthias Kaehlcke