Daniel Borkmann says:
====================
pull-request: bpf-next 2019-12-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 127 non-merge commits during the last 17 day(s) which contain
a total of 110 files changed, 6901 insertions(+), 2721 deletions(-).
There are three merge conflicts. Conflicts and resolution looks as follows:
1) Merge conflict in net/bpf/test_run.c:
There was a tree-wide cleanup c593642c8b ("treewide: Use sizeof_field() macro")
which gets in the way with b590cb5f80 ("bpf: Switch to offsetofend in
BPF_PROG_TEST_RUN"):
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, priority) +
sizeof_field(struct __sk_buff, priority),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, priority),
>>>>>>> 7c8dce4b16
There are a few occasions that look similar to this. Always take the chunk with
offsetofend(). Note that there is one where the fields differ in here:
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, tstamp) +
sizeof_field(struct __sk_buff, tstamp),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, gso_segs),
>>>>>>> 7c8dce4b16
Just take the one with offsetofend() /and/ gso_segs. Latter is correct due to
850a88cc40 ("bpf: Expose __sk_buff wire_len/gso_segs to BPF_PROG_TEST_RUN").
2) Merge conflict in arch/riscv/net/bpf_jit_comp.c:
(I'm keeping Bjorn in Cc here for a double-check in case I got it wrong.)
<<<<<<< HEAD
if (is_13b_check(off, insn))
return -1;
emit(rv_blt(tcc, RV_REG_ZERO, off >> 1), ctx);
=======
emit_branch(BPF_JSLT, RV_REG_T1, RV_REG_ZERO, off, ctx);
>>>>>>> 7c8dce4b16
Result should look like:
emit_branch(BPF_JSLT, tcc, RV_REG_ZERO, off, ctx);
3) Merge conflict in arch/riscv/include/asm/pgtable.h:
<<<<<<< HEAD
=======
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
#define vmemmap ((struct page *)VMEMMAP_START)
>>>>>>> 7c8dce4b16
Only take the BPF_* defines from there and move them higher up in the
same file. Remove the rest from the chunk. The VMALLOC_* etc defines
got moved via 01f52e16b8 ("riscv: define vmemmap before pfn_to_page
calls"). Result:
[...]
#define __S101 PAGE_READ_EXEC
#define __S110 PAGE_SHARED_EXEC
#define __S111 PAGE_SHARED_EXEC
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
[...]
Let me know if there are any other issues.
Anyway, the main changes are:
1) Extend bpftool to produce a struct (aka "skeleton") tailored and specific
to a provided BPF object file. This provides an alternative, simplified API
compared to standard libbpf interaction. Also, add libbpf extern variable
resolution for .kconfig section to import Kconfig data, from Andrii Nakryiko.
2) Add BPF dispatcher for XDP which is a mechanism to avoid indirect calls by
generating a branch funnel as discussed back in bpfconf'19 at LSF/MM. Also,
add various BPF riscv JIT improvements, from Björn Töpel.
3) Extend bpftool to allow matching BPF programs and maps by name,
from Paul Chaignon.
4) Support for replacing cgroup BPF programs attached with BPF_F_ALLOW_MULTI
flag for allowing updates without service interruption, from Andrey Ignatov.
5) Cleanup and simplification of ring access functions for AF_XDP with a
bonus of 0-5% performance improvement, from Magnus Karlsson.
6) Enable BPF JITs for x86-64 and arm64 by default. Also, final version of
audit support for BPF, from Daniel Borkmann and latter with Jiri Olsa.
7) Move and extend test_select_reuseport into BPF program tests under
BPF selftests, from Jakub Sitnicki.
8) Various BPF sample improvements for xdpsock for customizing parameters
to set up and benchmark AF_XDP, from Jay Jayatheerthan.
9) Improve libbpf to provide a ulimit hint on permission denied errors.
Also change XDP sample programs to attach in driver mode by default,
from Toke Høiland-Jørgensen.
10) Extend BPF test infrastructure to allow changing skb mark from tc BPF
programs, from Nikita V. Shirokov.
11) Optimize prologue code sequence in BPF arm32 JIT, from Russell King.
12) Fix xdp_redirect_cpu BPF sample to manually attach to tracepoints after
libbpf conversion, from Jesper Dangaard Brouer.
13) Minor misc improvements from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes. Upon closer analysis, it turns out that precise scalar
value tracking is missing a few precision markings for unknown scalars:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 0
1: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (35) if r0 >= 0xf72e goto pc+0
--> only follow fallthrough
2: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
2: (35) if r0 >= 0x80fe0000 goto pc+0
--> only follow fallthrough
3: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
3: (14) w0 -= -536870912
4: R0_w=invP536870912 R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (0f) r1 += r0
5: R0_w=invP536870912 R1_w=inv(id=0) R10=fp0
5: (55) if r1 != 0x104c1500 goto pc+0
--> push other branch for later analysis
R0_w=invP536870912 R1_w=inv273421568 R10=fp0
6: R0_w=invP536870912 R1_w=inv273421568 R10=fp0
6: (b7) r0 = 0
7: R0=invP0 R1=inv273421568 R10=fp0
7: (76) if w1 s>= 0xffffff00 goto pc+3
--> only follow goto
11: R0=invP0 R1=inv273421568 R10=fp0
11: (95) exit
6: R0_w=invP536870912 R1_w=inv(id=0) R10=fp0
6: (b7) r0 = 0
propagating r0
7: safe
processed 11 insns [...]
In the analysis of the second path coming after the successful exit above,
the path is being pruned at line 7. Pruning analysis found that both r0 are
precise P0 and both R1 are non-precise scalars and given prior path with
R1 as non-precise scalar succeeded, this one is therefore safe as well.
However, problem is that given condition at insn 7 in the first run, we only
followed goto and didn't push the other branch for later analysis, we've
never walked the few insns in there and therefore dead-code sanitation
rewrites it as goto pc-1, causing the hang depending on the skb address
hitting these conditions. The issue is that R1 should have been marked as
precise as well such that pruning enforces range check and conluded that new
R1 is not in range of old R1. In insn 4, we mark R1 (skb) as unknown scalar
via __mark_reg_unbounded() but not mark_reg_unbounded() and therefore
regs->precise remains as false.
Back in b5dc0163d8 ("bpf: precise scalar_value tracking"), this was not
the case since marking out of __mark_reg_unbounded() had this covered as well.
Once in both are set as precise in 4 as they should have been, we conclude
that given R1 was in prior fall-through path 0x104c1500 and now is completely
unknown, the check at insn 7 concludes that we need to continue walking.
Analysis after the fix:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 0
1: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (35) if r0 >= 0xf72e goto pc+0
2: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
2: (35) if r0 >= 0x80fe0000 goto pc+0
3: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
3: (14) w0 -= -536870912
4: R0_w=invP536870912 R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (0f) r1 += r0
5: R0_w=invP536870912 R1_w=invP(id=0) R10=fp0
5: (55) if r1 != 0x104c1500 goto pc+0
R0_w=invP536870912 R1_w=invP273421568 R10=fp0
6: R0_w=invP536870912 R1_w=invP273421568 R10=fp0
6: (b7) r0 = 0
7: R0=invP0 R1=invP273421568 R10=fp0
7: (76) if w1 s>= 0xffffff00 goto pc+3
11: R0=invP0 R1=invP273421568 R10=fp0
11: (95) exit
6: R0_w=invP536870912 R1_w=invP(id=0) R10=fp0
6: (b7) r0 = 0
7: R0_w=invP0 R1_w=invP(id=0) R10=fp0
7: (76) if w1 s>= 0xffffff00 goto pc+3
R0_w=invP0 R1_w=invP(id=0) R10=fp0
8: R0_w=invP0 R1_w=invP(id=0) R10=fp0
8: (a5) if r0 < 0x2007002a goto pc+0
9: R0_w=invP0 R1_w=invP(id=0) R10=fp0
9: (57) r0 &= -16316416
10: R0_w=invP0 R1_w=invP(id=0) R10=fp0
10: (a6) if w0 < 0x1201 goto pc+0
11: R0_w=invP0 R1_w=invP(id=0) R10=fp0
11: (95) exit
11: R0=invP0 R1=invP(id=0) R10=fp0
11: (95) exit
processed 16 insns [...]
Fixes: 6754172c20 ("bpf: fix precision tracking in presence of bpf2bpf calls")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191222223740.25297-1-daniel@iogearbox.net
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
The common use-case in production is to have multiple cgroup-bpf
programs per attach type that cover multiple use-cases. Such programs
are attached with BPF_F_ALLOW_MULTI and can be maintained by different
people.
Order of programs usually matters, for example imagine two egress
programs: the first one drops packets and the second one counts packets.
If they're swapped the result of counting program will be different.
It brings operational challenges with updating cgroup-bpf program(s)
attached with BPF_F_ALLOW_MULTI since there is no way to replace a
program:
* One way to update is to detach all programs first and then attach the
new version(s) again in the right order. This introduces an
interruption in the work a program is doing and may not be acceptable
(e.g. if it's egress firewall);
* Another way is attach the new version of a program first and only then
detach the old version. This introduces the time interval when two
versions of same program are working, what may not be acceptable if a
program is not idempotent. It also imposes additional burden on
program developers to make sure that two versions of their program can
co-exist.
Solve the problem by introducing a "replace" mode in BPF_PROG_ATTACH
command for cgroup-bpf programs being attached with BPF_F_ALLOW_MULTI
flag. This mode is enabled by newly introduced BPF_F_REPLACE attach flag
and bpf_attr.replace_bpf_fd attribute to pass fd of the old program to
replace
That way user can replace any program among those attached with
BPF_F_ALLOW_MULTI flag without the problems described above.
Details of the new API:
* If BPF_F_REPLACE is set but replace_bpf_fd doesn't have valid
descriptor of BPF program, BPF_PROG_ATTACH will return corresponding
error (EINVAL or EBADF).
* If replace_bpf_fd has valid descriptor of BPF program but such a
program is not attached to specified cgroup, BPF_PROG_ATTACH will
return ENOENT.
BPF_F_REPLACE is introduced to make the user intent clear, since
replace_bpf_fd alone can't be used for this (its default value, 0, is a
valid fd). BPF_F_REPLACE also makes it possible to extend the API in the
future (e.g. add BPF_F_BEFORE and BPF_F_AFTER if needed).
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Narkyiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/30cd850044a0057bdfcaaf154b7d2f39850ba813.1576741281.git.rdna@fb.com
__cgroup_bpf_attach has a lot of identical code to handle two scenarios:
BPF_F_ALLOW_MULTI is set and unset.
Simplify it by splitting the two main steps:
* First, the decision is made whether a new bpf_prog_list entry should
be allocated or existing entry should be reused for the new program.
This decision is saved in replace_pl pointer;
* Next, replace_pl pointer is used to handle both possible states of
BPF_F_ALLOW_MULTI flag (set / unset) instead of doing similar work for
them separately.
This splitting, in turn, allows to make further simplifications:
* The check for attaching same program twice in BPF_F_ALLOW_MULTI mode
can be done before allocating cgroup storage, so that if user tries to
attach same program twice no alloc/free happens as it was before;
* pl_was_allocated becomes redundant so it's removed.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/c6193db6fe630797110b0d3ff06c125d093b834c.1576741281.git.rdna@fb.com
The cpumap flush list is used to track entries that need to flushed
from via the xdp_do_flush_map() function. This list used to be
per-map, but there is really no reason for that. Instead make the
flush list global for all devmaps, which simplifies __cpu_map_flush()
and cpu_map_alloc().
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20191219061006.21980-7-bjorn.topel@gmail.com
The devmap flush list is used to track entries that need to flushed
from via the xdp_do_flush_map() function. This list used to be
per-map, but there is really no reason for that. Instead make the
flush list global for all devmaps, which simplifies __dev_map_flush()
and dev_map_init_map().
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20191219061006.21980-6-bjorn.topel@gmail.com
The xskmap flush list is used to track entries that need to flushed
from via the xdp_do_flush_map() function. This list used to be
per-map, but there is really no reason for that. Instead make the
flush list global for all xskmaps, which simplifies __xsk_map_flush()
and xsk_map_alloc().
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20191219061006.21980-5-bjorn.topel@gmail.com
After the RCU flavor consolidation [1], call_rcu() and
synchronize_rcu() waits for preempt-disable regions (NAPI) in addition
to the read-side critical sections. As a result of this, the cleanup
code in cpumap can be simplified
* There is no longer a need to flush in __cpu_map_entry_free, since we
know that this has been done when the call_rcu() callback is
triggered.
* When freeing the map, there is no need to explicitly wait for a
flush. It's guaranteed to be done after the synchronize_rcu() call
in cpu_map_free().
[1] https://lwn.net/Articles/777036/
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20191219061006.21980-3-bjorn.topel@gmail.com
After the RCU flavor consolidation [1], call_rcu() and
synchronize_rcu() waits for preempt-disable regions (NAPI) in addition
to the read-side critical sections. As a result of this, the cleanup
code in devmap can be simplified
* There is no longer a need to flush in __dev_map_entry_free, since we
know that this has been done when the call_rcu() callback is
triggered.
* When freeing the map, there is no need to explicitly wait for a
flush. It's guaranteed to be done after the synchronize_rcu() call
in dev_map_free(). The rcu_barrier() is still needed, so that the
map is not freed prior the elements.
[1] https://lwn.net/Articles/777036/
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20191219061006.21980-2-bjorn.topel@gmail.com
While testing Cilium with /unreleased/ Linus' tree under BPF-based NodePort
implementation, I noticed a strange BPF SNAT engine behavior from time to
time. In some cases it would do the correct SNAT/DNAT service translation,
but at a random point in time it would just stop and perform an unexpected
translation after SYN, SYN/ACK and stack would send a RST back. While initially
assuming that there is some sort of a race condition in BPF code, adding
trace_printk()s for debugging purposes at some point seemed to have resolved
the issue auto-magically.
Digging deeper on this Heisenbug and reducing the trace_printk() calls to
an absolute minimum, it turns out that a single call would suffice to
trigger / not trigger the seen RST issue, even though the logic of the
program itself remains unchanged. Turns out the single call changed verifier
pruning behavior to get everything to work. Reconstructing a minimal test
case, the incorrect JIT dump looked as follows:
# bpftool p d j i 11346
0xffffffffc0cba96c:
[...]
21: movzbq 0x30(%rdi),%rax
26: cmp $0xd,%rax
2a: je 0x000000000000003a
2c: xor %edx,%edx
2e: movabs $0xffff89cc74e85800,%rsi
38: jmp 0x0000000000000049
3a: mov $0x2,%edx
3f: movabs $0xffff89cc74e85800,%rsi
49: mov -0x224(%rbp),%eax
4f: cmp $0x20,%eax
52: ja 0x0000000000000062
54: add $0x1,%eax
57: mov %eax,-0x224(%rbp)
5d: jmpq 0xffffffffffff6911
62: mov $0x1,%eax
[...]
Hence, unexpectedly, JIT emitted a direct jump even though retpoline based
one would have been needed since in line 2c and 3a we have different slot
keys in BPF reg r3. Verifier log of the test case reveals what happened:
0: (b7) r0 = 14
1: (73) *(u8 *)(r1 +48) = r0
2: (71) r0 = *(u8 *)(r1 +48)
3: (15) if r0 == 0xd goto pc+4
R0_w=inv(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (b7) r3 = 0
5: (18) r2 = 0xffff89cc74d54a00
7: (05) goto pc+3
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
from 3 to 8: R0_w=inv13 R1=ctx(id=0,off=0,imm=0) R10=fp0
8: (b7) r3 = 2
9: (18) r2 = 0xffff89cc74d54a00
11: safe
processed 13 insns (limit 1000000) [...]
Second branch is pruned by verifier since considered safe, but issue is that
record_func_key() couldn't have seen the index in line 3a and therefore
decided that emitting a direct jump at this location was okay.
Fix this by reusing our backtracking logic for precise scalar verification
in order to prevent pruning on the slot key. This means verifier will track
content of r3 all the way backwards and only prune if both scalars were
unknown in state equivalence check and therefore poisoned in the first place
in record_func_key(). The range is [x,x] in record_func_key() case since
the slot always would have to be constant immediate. Correct verification
after fix:
0: (b7) r0 = 14
1: (73) *(u8 *)(r1 +48) = r0
2: (71) r0 = *(u8 *)(r1 +48)
3: (15) if r0 == 0xd goto pc+4
R0_w=invP(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (b7) r3 = 0
5: (18) r2 = 0x0
7: (05) goto pc+3
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
from 3 to 8: R0_w=invP13 R1=ctx(id=0,off=0,imm=0) R10=fp0
8: (b7) r3 = 2
9: (18) r2 = 0x0
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
processed 15 insns (limit 1000000) [...]
And correct corresponding JIT dump:
# bpftool p d j i 11
0xffffffffc0dc34c4:
[...]
21: movzbq 0x30(%rdi),%rax
26: cmp $0xd,%rax
2a: je 0x000000000000003a
2c: xor %edx,%edx
2e: movabs $0xffff9928b4c02200,%rsi
38: jmp 0x0000000000000049
3a: mov $0x2,%edx
3f: movabs $0xffff9928b4c02200,%rsi
49: cmp $0x4,%rdx
4d: jae 0x0000000000000093
4f: and $0x3,%edx
52: mov %edx,%edx
54: cmp %edx,0x24(%rsi)
57: jbe 0x0000000000000093
59: mov -0x224(%rbp),%eax
5f: cmp $0x20,%eax
62: ja 0x0000000000000093
64: add $0x1,%eax
67: mov %eax,-0x224(%rbp)
6d: mov 0x110(%rsi,%rdx,8),%rax
75: test %rax,%rax
78: je 0x0000000000000093
7a: mov 0x30(%rax),%rax
7e: add $0x19,%rax
82: callq 0x000000000000008e
87: pause
89: lfence
8c: jmp 0x0000000000000087
8e: mov %rax,(%rsp)
92: retq
93: mov $0x1,%eax
[...]
Also explicitly adding explicit env->allow_ptr_leaks to fixup_bpf_calls() since
backtracking is enabled under former (direct jumps as well, but use different
test). In case of only tracking different map pointers as in c93552c443 ("bpf:
properly enforce index mask to prevent out-of-bounds speculation"), pruning
cannot make such short-cuts, neither if there are paths with scalar and non-scalar
types as r3. mark_chain_precision() is only needed after we know that
register_is_const(). If it was not the case, we already poison the key on first
path and non-const key in later paths are not matching the scalar range in regsafe()
either. Cilium NodePort testing passes fine as well now. Note, released kernels
not affected.
Fixes: d2e4c1e6c2 ("bpf: Constant map key tracking for prog array pokes")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/ac43ffdeb7386c5bd688761ed266f3722bb39823.1576789878.git.daniel@iogearbox.net
The two callers of bpf_prog_realloc - bpf_patch_insn_single and
bpf_migrate_filter dereference the struct fp_old, before passing
it to the function. Thus assertion to check fp_old is unnecessary
and can be removed.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191219175735.19231-1-pakki001@umn.edu
Recently noticed that we're tracking programs related to local storage maps
through their prog pointer. This is a wrong assumption since the prog pointer
can still change throughout the verification process, for example, whenever
bpf_patch_insn_single() is called.
Therefore, the prog pointer that was assigned via bpf_cgroup_storage_assign()
is not guaranteed to be the same as we pass in bpf_cgroup_storage_release()
and the map would therefore remain in busy state forever. Fix this by using
the prog's aux pointer which is stable throughout verification and beyond.
Fixes: de9cbbaadb ("bpf: introduce cgroup storage maps")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/1471c69eca3022218666f909bc927a92388fd09e.1576580332.git.daniel@iogearbox.net
Commit da765a2f59 ("bpf: Add poke dependency tracking for prog array
maps") wrongly assumed that in case of prog load errors, we're cleaning
up all program tracking via bpf_free_used_maps().
However, it can happen that we're still at the point where we didn't copy
map pointers into the prog's aux section such that env->prog->aux->used_maps
is still zero, running into a UAF. In such case, the verifier has similar
release_maps() helper that drops references to used maps from its env.
Consolidate the release code into __bpf_free_used_maps() and call it from
all sides to fix it.
Fixes: da765a2f59 ("bpf: Add poke dependency tracking for prog array maps")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/1c2909484ca524ae9f55109b06f22b6213e76376.1576514756.git.daniel@iogearbox.net
This commit adds a BPF dispatcher for XDP. The dispatcher is updated
from the XDP control-path, dev_xdp_install(), and used when an XDP
program is run via bpf_prog_run_xdp().
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191213175112.30208-4-bjorn.topel@gmail.com
The BPF dispatcher is a multi-way branch code generator, mainly
targeted for XDP programs. When an XDP program is executed via the
bpf_prog_run_xdp(), it is invoked via an indirect call. The indirect
call has a substantial performance impact, when retpolines are
enabled. The dispatcher transform indirect calls to direct calls, and
therefore avoids the retpoline. The dispatcher is generated using the
BPF JIT, and relies on text poking provided by bpf_arch_text_poke().
The dispatcher hijacks a trampoline function it via the __fentry__ nop
of the trampoline. One dispatcher instance currently supports up to 64
dispatch points. A user creates a dispatcher with its corresponding
trampoline with the DEFINE_BPF_DISPATCHER macro.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191213175112.30208-3-bjorn.topel@gmail.com
Refactor the image allocation in the BPF trampoline code into a
separate function, so it can be shared with the BPF dispatcher in
upcoming commits.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191213175112.30208-2-bjorn.topel@gmail.com
After Spectre 2 fix via 290af86629 ("bpf: introduce BPF_JIT_ALWAYS_ON
config") most major distros use BPF_JIT_ALWAYS_ON configuration these days
which compiles out the BPF interpreter entirely and always enables the
JIT. Also given recent fix in e1608f3fa8 ("bpf: Avoid setting bpf insns
pages read-only when prog is jited"), we additionally avoid fragmenting
the direct map for the BPF insns pages sitting in the general data heap
since they are not used during execution. Latter is only needed when run
through the interpreter.
Since both x86 and arm64 JITs have seen a lot of exposure over the years,
are generally most up to date and maintained, there is more downside in
!BPF_JIT_ALWAYS_ON configurations to have the interpreter enabled by default
rather than the JIT. Add a ARCH_WANT_DEFAULT_BPF_JIT config which archs can
use to set the bpf_jit_{enable,kallsyms} to 1. Back in the days the
bpf_jit_kallsyms knob was set to 0 by default since major distros still
had /proc/kallsyms addresses exposed to unprivileged user space which is
not the case anymore. Hence both knobs are set via BPF_JIT_DEFAULT_ON which
is set to 'y' in case of BPF_JIT_ALWAYS_ON or ARCH_WANT_DEFAULT_BPF_JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/f78ad24795c2966efcc2ee19025fa3459f622185.1575903816.git.daniel@iogearbox.net
Make BPF trampoline attach its generated assembly code to kernel functions via
register_ftrace_direct() API. It helps ftrace-based tracers co-exist with BPF
trampoline on the same kernel function. It also switches attaching logic from
arch specific text_poke to generic ftrace that is available on many
architectures. text_poke is still necessary for bpf-to-bpf attach and for
bpf_tail_call optimization.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191209000114.1876138-3-ast@kernel.org
Allow for audit messages to be emitted upon BPF program load and
unload for having a timeline of events. The load itself is in
syscall context, so additional info about the process initiating
the BPF prog creation can be logged and later directly correlated
to the unload event.
The only info really needed from BPF side is the globally unique
prog ID where then audit user space tooling can query / dump all
info needed about the specific BPF program right upon load event
and enrich the record, thus these changes needed here can be kept
small and non-intrusive to the core.
Raw example output:
# auditctl -D
# auditctl -a always,exit -F arch=x86_64 -S bpf
# ausearch --start recent -m 1334
...
----
time->Wed Nov 27 16:04:13 2019
type=PROCTITLE msg=audit(1574867053.120:84664): proctitle="./bpf"
type=SYSCALL msg=audit(1574867053.120:84664): arch=c000003e syscall=321 \
success=yes exit=3 a0=5 a1=7ffea484fbe0 a2=70 a3=0 items=0 ppid=7477 \
pid=12698 auid=1001 uid=1001 gid=1001 euid=1001 suid=1001 fsuid=1001 \
egid=1001 sgid=1001 fsgid=1001 tty=pts2 ses=4 comm="bpf" \
exe="/home/jolsa/auditd/audit-testsuite/tests/bpf/bpf" \
subj=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023 key=(null)
type=UNKNOWN[1334] msg=audit(1574867053.120:84664): prog-id=76 op=LOAD
----
time->Wed Nov 27 16:04:13 2019
type=UNKNOWN[1334] msg=audit(1574867053.120:84665): prog-id=76 op=UNLOAD
...
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Co-developed-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Link: https://lore.kernel.org/bpf/20191206214934.11319-1-jolsa@kernel.org
Building with -Werror showed another failure:
kernel/bpf/btf.c: In function 'btf_get_prog_ctx_type.isra.31':
kernel/bpf/btf.c:3508:63: error: array subscript 0 is above array bounds of 'u8[0]' {aka 'unsigned char[0]'} [-Werror=array-bounds]
ctx_type = btf_type_member(conv_struct) + bpf_ctx_convert_map[prog_type] * 2;
I don't actually understand why the array is empty, but a similar
fix has addressed a related problem, so I suppose we can do the
same thing here.
Fixes: ce27709b81 ("bpf: Fix build in minimal configurations")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191210203553.2941035-1-arnd@arndb.de
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Pull networking fixes from David Miller:
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
For jited bpf program, if the subprogram count is 1, i.e.,
there is no callees in the program, prog->aux->func will be NULL
and prog->bpf_func points to image address of the program.
If there is more than one subprogram, prog->aux->func is populated,
and subprogram 0 can be accessed through either prog->bpf_func or
prog->aux->func[0]. Other subprograms should be accessed through
prog->aux->func[subprog_id].
This patch fixed a bug in check_attach_btf_id(), where
prog->aux->func[subprog_id] is used to access any subprogram which
caused a segfault like below:
[79162.619208] BUG: kernel NULL pointer dereference, address:
0000000000000000
......
[79162.634255] Call Trace:
[79162.634974] ? _cond_resched+0x15/0x30
[79162.635686] ? kmem_cache_alloc_trace+0x162/0x220
[79162.636398] ? selinux_bpf_prog_alloc+0x1f/0x60
[79162.637111] bpf_prog_load+0x3de/0x690
[79162.637809] __do_sys_bpf+0x105/0x1740
[79162.638488] do_syscall_64+0x5b/0x180
[79162.639147] entry_SYSCALL_64_after_hwframe+0x44/0xa9
......
Fixes: 5b92a28aae ("bpf: Support attaching tracing BPF program to other BPF programs")
Reported-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191205010606.177774-1-yhs@fb.com
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
Daniel Borkmann says:
====================
pull-request: bpf 2019-12-02
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 6 day(s) which contain
a total of 10 files changed, 60 insertions(+), 51 deletions(-).
The main changes are:
1) Fix vmlinux BTF generation for binutils pre v2.25, from Stanislav Fomichev.
2) Fix libbpf global variable relocation to take symbol's st_value offset
into account, from Andrii Nakryiko.
3) Fix libbpf build on powerpc where check_abi target fails due to different
readelf output format, from Aurelien Jarno.
4) Don't set BPF insns RO for the case when they are JITed in order to avoid
fragmenting the direct map, from Daniel Borkmann.
5) Fix static checker warning in btf_distill_func_proto() as well as a build
error due to empty enum when BPF is compiled out, from Alexei Starovoitov.
6) Fix up generation of bpf_helper_defs.h for perf, from Arnaldo Carvalho de Melo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some kconfigs can have BPF enabled without a single valid program type.
In such configurations the build will fail with:
./kernel/bpf/btf.c:3466:1: error: empty enum is invalid
Fix it by adding unused value to the enum.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/bpf/20191128043508.2346723-1-ast@kernel.org
kernel/bpf/btf.c:4023 btf_distill_func_proto()
error: potentially dereferencing uninitialized 't'.
kernel/bpf/btf.c
4012 nargs = btf_type_vlen(func);
4013 if (nargs >= MAX_BPF_FUNC_ARGS) {
4014 bpf_log(log,
4015 "The function %s has %d arguments. Too many.\n",
4016 tname, nargs);
4017 return -EINVAL;
4018 }
4019 ret = __get_type_size(btf, func->type, &t);
^^
t isn't initialized for the first -EINVAL return
This is unlikely path, since BTF should have been validated at this point.
Fix it by returning 'void' BTF.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191126230106.237179-1-ast@kernel.org
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:
- Dynamic tick (nohz) updates, perhaps most notably changes to force
the tick on when needed due to lengthy in-kernel execution on CPUs
on which RCU is waiting.
- Linux-kernel memory consistency model updates.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Documentation updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
security/safesetid: Replace rcu_swap_protected() with rcu_replace_pointer()
net/sched: Replace rcu_swap_protected() with rcu_replace_pointer()
net/netfilter: Replace rcu_swap_protected() with rcu_replace_pointer()
net/core: Replace rcu_swap_protected() with rcu_replace_pointer()
bpf/cgroup: Replace rcu_swap_protected() with rcu_replace_pointer()
fs/afs: Replace rcu_swap_protected() with rcu_replace_pointer()
drivers/scsi: Replace rcu_swap_protected() with rcu_replace_pointer()
drm/i915: Replace rcu_swap_protected() with rcu_replace_pointer()
x86/kvm/pmu: Replace rcu_swap_protected() with rcu_replace_pointer()
rcu: Upgrade rcu_swap_protected() to rcu_replace_pointer()
rcu: Suppress levelspread uninitialized messages
rcu: Fix uninitialized variable in nocb_gp_wait()
rcu: Update descriptions for rcu_future_grace_period tracepoint
rcu: Update descriptions for rcu_nocb_wake tracepoint
rcu: Remove obsolete descriptions for rcu_barrier tracepoint
rcu: Ensure that ->rcu_urgent_qs is set before resched IPI
workqueue: Convert for_each_wq to use built-in list check
rcu: Several rcu_segcblist functions can be static
rcu: Remove unused function hlist_bl_del_init_rcu()
Documentation: Rename rcu_node_context_switch() to rcu_note_context_switch()
...
Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:
1) Support alternative names for network devices, from Jiri Pirko.
2) Introduce per-netns netdev notifiers, also from Jiri Pirko.
3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.
4) Allow compiling out the TLS TOE code, from Jakub Kicinski.
5) Add several new tracepoints to the kTLS code, also from Jakub.
6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.
7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.
8) Add XDP support to mvneta driver, from Lorenzo Bianconi.
9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.
10) PTP support for aquantia chips, from Egor Pomozov.
11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.
12) Add smart nagle to tipc, from Jon Maloy.
13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.
14) Add a flow mask cache to OVS, from Tonghao Zhang.
15) Add XDP support to ice driver, from Maciej Fijalkowski.
16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.
17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.
18) Support it in stmmac driver too, from Jose Abreu.
19) Support TIPC encryption and auth, from Tuong Lien.
20) Introduce BPF trampolines, from Alexei Starovoitov.
21) Make page_pool API more numa friendly, from Saeed Mahameed.
22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.
23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...
Pull cgroup updates from Tejun Heo:
"There are several notable changes here:
- Single thread migrating itself has been optimized so that it
doesn't need threadgroup rwsem anymore.
- Freezer optimization to avoid unnecessary frozen state changes.
- cgroup ID unification so that cgroup fs ino is the only unique ID
used for the cgroup and can be used to directly look up live
cgroups through filehandle interface on 64bit ino archs. On 32bit
archs, cgroup fs ino is still the only ID in use but it is only
unique when combined with gen.
- selftest and other changes"
* 'for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (24 commits)
writeback: fix -Wformat compilation warnings
docs: cgroup: mm: Fix spelling of "list"
cgroup: fix incorrect WARN_ON_ONCE() in cgroup_setup_root()
cgroup: use cgrp->kn->id as the cgroup ID
kernfs: use 64bit inos if ino_t is 64bit
kernfs: implement custom exportfs ops and fid type
kernfs: combine ino/id lookup functions into kernfs_find_and_get_node_by_id()
kernfs: convert kernfs_node->id from union kernfs_node_id to u64
kernfs: kernfs_find_and_get_node_by_ino() should only look up activated nodes
kernfs: use dumber locking for kernfs_find_and_get_node_by_ino()
netprio: use css ID instead of cgroup ID
writeback: use ino_t for inodes in tracepoints
kernfs: fix ino wrap-around detection
kselftests: cgroup: Avoid the reuse of fd after it is deallocated
cgroup: freezer: don't change task and cgroups status unnecessarily
cgroup: use cgroup->last_bstat instead of cgroup->bstat_pending for consistency
cgroup: remove cgroup_enable_task_cg_lists() optimization
cgroup: pids: use atomic64_t for pids->limit
selftests: cgroup: Run test_core under interfering stress
selftests: cgroup: Add task migration tests
...
Given that we have BPF_MOD_NOP_TO_{CALL,JUMP}, BPF_MOD_{CALL,JUMP}_TO_NOP
and BPF_MOD_{CALL,JUMP}_TO_{CALL,JUMP} poke types and that we also pass in
old_addr as well as new_addr, it's a bit redundant and unnecessarily
complicates __bpf_arch_text_poke() itself since we can derive the same from
the *_addr that were passed in. Hence simplify and use BPF_MOD_{CALL,JUMP}
as types which also allows to clean up call-sites.
In addition to that, __bpf_arch_text_poke() currently verifies that text
matches expected old_insn before we invoke text_poke_bp(). Also add a check
on new_insn and skip rewrite if it already matches. Reason why this is rather
useful is that it avoids making any special casing in prog_array_map_poke_run()
when old and new prog were NULL and has the benefit that also for this case
we perform a check on text whether it really matches our expectations.
Suggested-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/fcb00a2b0b288d6c73de4ef58116a821c8fe8f2f.1574555798.git.daniel@iogearbox.net
Add tracking of constant keys into tail call maps. The signature of
bpf_tail_call_proto is that arg1 is ctx, arg2 map pointer and arg3
is a index key. The direct call approach for tail calls can be enabled
if the verifier asserted that for all branches leading to the tail call
helper invocation, the map pointer and index key were both constant
and the same.
Tracking of map pointers we already do from prior work via c93552c443
("bpf: properly enforce index mask to prevent out-of-bounds speculation")
and 09772d92cd ("bpf: avoid retpoline for lookup/update/ delete calls
on maps").
Given the tail call map index key is not on stack but directly in the
register, we can add similar tracking approach and later in fixup_bpf_calls()
add a poke descriptor to the progs poke_tab with the relevant information
for the JITing phase.
We internally reuse insn->imm for the rewritten BPF_JMP | BPF_TAIL_CALL
instruction in order to point into the prog's poke_tab, and keep insn->imm
as 0 as indicator that current indirect tail call emission must be used.
Note that publishing to the tracker must happen at the end of fixup_bpf_calls()
since adding elements to the poke_tab reallocates its memory, so we need
to wait until its in final state.
Future work can generalize and add similar approach to optimize plain
array map lookups. Difference there is that we need to look into the key
value that sits on stack. For clarity in bpf_insn_aux_data, map_state
has been renamed into map_ptr_state, so we get map_{ptr,key}_state as
trackers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/e8db37f6b2ae60402fa40216c96738ee9b316c32.1574452833.git.daniel@iogearbox.net
This work adds program tracking to prog array maps. This is needed such
that upon prog array updates/deletions we can fix up all programs which
make use of this tail call map. We add ops->map_poke_{un,}track()
helpers to maps to maintain the list of programs and ops->map_poke_run()
for triggering the actual update.
bpf_array_aux is extended to contain the list head and poke_mutex in
order to serialize program patching during updates/deletions.
bpf_free_used_maps() will untrack the program shortly before dropping
the reference to the map. For clearing out the prog array once all urefs
are dropped we need to use schedule_work() to have a sleepable context.
The prog_array_map_poke_run() is triggered during updates/deletions and
walks the maintained prog list. It checks in their poke_tabs whether the
map and key is matching and runs the actual bpf_arch_text_poke() for
patching in the nop or new jmp location. Depending on the type of update,
we use one of BPF_MOD_{NOP_TO_JUMP,JUMP_TO_NOP,JUMP_TO_JUMP}.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1fb364bb3c565b3e415d5ea348f036ff379e779d.1574452833.git.daniel@iogearbox.net
Add initial poke table data structures and management to the BPF
prog that can later be used by JITs. Also add an instance of poke
specific data for tail call maps; plan for later work is to extend
this also for BPF static keys.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1db285ec2ea4207ee0455b3f8e191a4fc58b9ade.1574452833.git.daniel@iogearbox.net
We're going to extend this with further information which is only
relevant for prog array at this point. Given this info is not used
in critical path, move it into its own structure such that the main
array map structure can be kept on diet.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/b9ddccdb0f6f7026489ee955f16c96381e1e7238.1574452833.git.daniel@iogearbox.net
We later on are going to need a sleepable context as opposed to plain
RCU callback in order to untrack programs we need to poke at runtime
and tracking as well as image update is performed under mutex.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/09823b1d5262876e9b83a8e75df04cf0467357a4.1574452833.git.daniel@iogearbox.net
With latest llvm (trunk https://github.com/llvm/llvm-project),
test_progs, which has +alu32 enabled, failed for strobemeta.o.
The verifier output looks like below with edit to replace large
decimal numbers with hex ones.
193: (85) call bpf_probe_read_user_str#114
R0=inv(id=0)
194: (26) if w0 > 0x1 goto pc+4
R0_w=inv(id=0,umax_value=0xffffffff00000001)
195: (6b) *(u16 *)(r7 +80) = r0
196: (bc) w6 = w0
R6_w=inv(id=0,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
197: (67) r6 <<= 32
R6_w=inv(id=0,smax_value=0x7fffffff00000000,umax_value=0xffffffff00000000,
var_off=(0x0; 0xffffffff00000000))
198: (77) r6 >>= 32
R6=inv(id=0,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
...
201: (79) r8 = *(u64 *)(r10 -416)
R8_w=map_value(id=0,off=40,ks=4,vs=13872,imm=0)
202: (0f) r8 += r6
R8_w=map_value(id=0,off=40,ks=4,vs=13872,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
203: (07) r8 += 9696
R8_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
...
255: (bf) r1 = r8
R1_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
...
257: (85) call bpf_probe_read_user_str#114
R1 unbounded memory access, make sure to bounds check any array access into a map
The value range for register r6 at insn 198 should be really just 0/1.
The umax_value=0xffffffff caused later verification failure.
After jmp instructions, the current verifier already tried to use just
obtained information to get better register range. The current mechanism is
for 64bit register only. This patch implemented to tighten the range
for 32bit sub-registers after jmp32 instructions.
With the patch, we have the below range ranges for the
above code sequence:
193: (85) call bpf_probe_read_user_str#114
R0=inv(id=0)
194: (26) if w0 > 0x1 goto pc+4
R0_w=inv(id=0,smax_value=0x7fffffff00000001,umax_value=0xffffffff00000001,
var_off=(0x0; 0xffffffff00000001))
195: (6b) *(u16 *)(r7 +80) = r0
196: (bc) w6 = w0
R6_w=inv(id=0,umax_value=0xffffffff,var_off=(0x0; 0x1))
197: (67) r6 <<= 32
R6_w=inv(id=0,umax_value=0x100000000,var_off=(0x0; 0x100000000))
198: (77) r6 >>= 32
R6=inv(id=0,umax_value=1,var_off=(0x0; 0x1))
...
201: (79) r8 = *(u64 *)(r10 -416)
R8_w=map_value(id=0,off=40,ks=4,vs=13872,imm=0)
202: (0f) r8 += r6
R8_w=map_value(id=0,off=40,ks=4,vs=13872,umax_value=1,var_off=(0x0; 0x1))
203: (07) r8 += 9696
R8_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=1,var_off=(0x0; 0x1))
...
255: (bf) r1 = r8
R1_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=1,var_off=(0x0; 0x1))
...
257: (85) call bpf_probe_read_user_str#114
...
At insn 194, the register R0 has better var_off.mask and smax_value.
Especially, the var_off.mask ensures later lshift and rshift
maintains proper value range.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191121170650.449030-1-yhs@fb.com
Tetsuo pointed out that it was not only the device unregister hook that was
broken for devmap_hash types, it was also cleanup on map free. So better
fix this as well.
While we're at it, there's no reason to allocate the netdev_map array for
DEVMAP_HASH, so skip that and adjust the cost accordingly.
Fixes: 6f9d451ab1 ("xdp: Add devmap_hash map type for looking up devices by hashed index")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20191121133612.430414-1-toke@redhat.com
This commit reverts commit 91e6015b08 ("bpf: Emit audit messages
upon successful prog load and unload") and its follow up commit
7599a896f2 ("audit: Move audit_log_task declaration under
CONFIG_AUDITSYSCALL") as requested by Paul Moore. The change needs
close review on linux-audit, tests etc.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca74886c433:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Given we recently extended the original bpf_map_area_alloc() helper in
commit fc9702273e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"),
we need to apply the same logic as in ff1c08e1f7 ("bpf: Change size
to u64 for bpf_map_{area_alloc, charge_init}()"). To avoid conflicts,
extend it for bpf-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Allow for audit messages to be emitted upon BPF program load and
unload for having a timeline of events. The load itself is in
syscall context, so additional info about the process initiating
the BPF prog creation can be logged and later directly correlated
to the unload event.
The only info really needed from BPF side is the globally unique
prog ID where then audit user space tooling can query / dump all
info needed about the specific BPF program right upon load event
and enrich the record, thus these changes needed here can be kept
small and non-intrusive to the core.
Raw example output:
# auditctl -D
# auditctl -a always,exit -F arch=x86_64 -S bpf
# ausearch --start recent -m 1334
[...]
----
time->Wed Nov 20 12:45:51 2019
type=PROCTITLE msg=audit(1574271951.590:8974): proctitle="./test_verifier"
type=SYSCALL msg=audit(1574271951.590:8974): arch=c000003e syscall=321 success=yes exit=14 a0=5 a1=7ffe2d923e80 a2=78 a3=0 items=0 ppid=742 pid=949 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=pts0 ses=2 comm="test_verifier" exe="/root/bpf-next/tools/testing/selftests/bpf/test_verifier" subj=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023 key=(null)
type=UNKNOWN[1334] msg=audit(1574271951.590:8974): auid=0 uid=0 gid=0 ses=2 subj=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023 pid=949 comm="test_verifier" exe="/root/bpf-next/tools/testing/selftests/bpf/test_verifier" prog-id=3260 event=LOAD
----
time->Wed Nov 20 12:45:51 2019
type=UNKNOWN[1334] msg=audit(1574271951.590:8975): prog-id=3260 event=UNLOAD
----
[...]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191120213816.8186-1-jolsa@kernel.org
Fix sparse warning:
kernel/bpf/arraymap.c:481:5: warning:
symbol 'array_map_mmap' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191119142113.15388-1-yuehaibing@huawei.com
Add ability to memory-map contents of BPF array map. This is extremely useful
for working with BPF global data from userspace programs. It allows to avoid
typical bpf_map_{lookup,update}_elem operations, improving both performance
and usability.
There had to be special considerations for map freezing, to avoid having
writable memory view into a frozen map. To solve this issue, map freezing and
mmap-ing is happening under mutex now:
- if map is already frozen, no writable mapping is allowed;
- if map has writable memory mappings active (accounted in map->writecnt),
map freezing will keep failing with -EBUSY;
- once number of writable memory mappings drops to zero, map freezing can be
performed again.
Only non-per-CPU plain arrays are supported right now. Maps with spinlocks
can't be memory mapped either.
For BPF_F_MMAPABLE array, memory allocation has to be done through vmalloc()
to be mmap()'able. We also need to make sure that array data memory is
page-sized and page-aligned, so we over-allocate memory in such a way that
struct bpf_array is at the end of a single page of memory with array->value
being aligned with the start of the second page. On deallocation we need to
accomodate this memory arrangement to free vmalloc()'ed memory correctly.
One important consideration regarding how memory-mapping subsystem functions.
Memory-mapping subsystem provides few optional callbacks, among them open()
and close(). close() is called for each memory region that is unmapped, so
that users can decrease their reference counters and free up resources, if
necessary. open() is *almost* symmetrical: it's called for each memory region
that is being mapped, **except** the very first one. So bpf_map_mmap does
initial refcnt bump, while open() will do any extra ones after that. Thus
number of close() calls is equal to number of open() calls plus one more.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-4-andriin@fb.com
David S. Miller
Daniel Borkmann
Linus Torvalds
Andrey Ignatov
Björn Töpel
Aditya Pakki
Alexei Starovoitov
Arnd Bergmann
Pankaj Bharadiya
Yonghong Song
Toke Høiland-Jørgensen
Jakub Kicinski
YueHaibing
Andrii Nakryiko