Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert a thinko in commit d2f119fe319528da8c76a1107459d6f478cbf28c:
When knodemgrd starts, it needs to sleep until host->generation was
incremented above its initial value of 0. My wrong logic caused it to
start sending requests when the bus wasn't completely ready. Seen as
"AT dma reset ctx=0, aborting transmission" messages in 2.6.19-rc1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
nodemgr_resume_ne was iterating over nodemgr_ud_class.children without
protection by nodemgr_ud_class.subsys.rwsem.
FIXME:
Shouldn't we rather use class->sem there, not class->subsys.rwsem?
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
nodemgr_update_pdrv grabbed an rw semaphore (as reader) which was
already taken by its caller's caller, nodemgr_probe_ne (as reader too).
Reported by Miles Lane, call path pointed out by Arjan van de Ven.
FIXME:
Shouldn't we rather use class->sem there, not class->subsys.rwsem?
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch reduces the size of struct hpsb_host and also removes
semaphores from ieee1394_transactions.c. On i386, struct hpsb_host
shrinks from 10656 bytes to 6688 bytes. This is accomplished by
- using a single wait_queue for hpsb_get_tlabel instead of many
instances of semaphores,
- using a single lock to serialize access to all tlabel pools (the
protected code regions are small, i.e. lock contention very low),
- omitting the sysfs attribute tlabels_allocations.
Drawback: In the rare case that a process needs to sleep because all
transaction labels for the node are temporarily exhausted, it is also
woken up if a tlabel for a different node became free, checks for an
available tlabel, and is put to sleep again. The check is not costly
and the situation occurs extremely rarely. (Tlabels are typically
only exhausted if there was no context switch to the khpsbpkt thread
which recycles tlables.) Therefore the benefit of reduced tpool size
outweighs this drawback.
The sysfs attributes tlabels_free and tlabels_mask are not compiled
anymore unless CONFIG_IEEE1394_VERBOSEDEBUG is set.
The by far biggest member of struct hpsb_host, the struct csr_control
csr (5272 bytes on i386), is now placed at the end of struct hpsb_host.
Note, hpsb_get_tlabel calls the macro wait_event_interruptible with a
condition argument which has a side effect (allocation of a tlabel and
manipulation of the packet). This side effect happens only if the
condition is true. The patch relies on wait_event_interruptible not
evaluating the condition again after it became true.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Another trivial sem2mutex conversion.
Side note: nodemgr_serialize's purpose, when introduced in linux1394's
revision 529 in July 2002, was to protect several data structures which
are now largely handled by or together with Linux' driver core and are
now protected by the LDM's own mechanisms. It may very well be possible
to remove this mutex now. But fully parallelized node scanning is on
our long-term TODO list anyway; the mutex will certainly go away then.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Convert nodemgr's host thread from kernel_thread to kthread and its
sleep/restart mechanism from a counting semaphore to a schedule()/
wake_up_process() scheme.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Nodemgr's ignore_drivers variable is exposed as a module load parameter
(therefore also as a sysfs attribute below /sys/module) and additionally
as an attribute below /sys/bus/ieee1394. Since the latter is writable,
make the former writable too.
Note, the bus's attribute ignore_drivers is only relevant to newly added
units, not to present or suspended or resuming units. Those have their
own attribute ignore_driver.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
nodemgr.c::fw_set_rescan() is used to re-run the driver core over
nodemgr's representation of unit directories in order to initiate
protocol driver probes. It is initiated via write access to one of
nodemgr's sysfs attributes. The purpose is to attach drivers to
units after switching a unit's ignore_driver attribute from 1 to 0.
It is not really necessary to fork a kernel_thread for this job. The
call to kernel_thread() can be eliminated to avoid the deprecated API
and to simplify the code a bit.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Remove unnecessary includes, add missing includes.
Use forward type declarations for some structs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
If ieee1394.h::IEEE1394_SPEED_MAX is bigger than the actual speed of an
1394b host adapter and the speed to another 1394b node was probed, a
bigger speed than actually used was kept in host->speed[n]. The only
resulting problem so far was sbp2 displaying bogus values in the syslog,
e.g. S3200 for actual S800 connections if IEEE1394_SPEED_MAX was S3200.
But other high-level drivers which access this field could get into more
trouble. (Eth1394 is the only other in-tree driver which does so. It
seems it is not affected.)
Nodemgr now clips this value according to the host adapter's link speed.
A pointer expression in nodemgr_check_speed is also changed for clarity.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Also revert patch "frv: ieee1394 is borken on frv", as it no longer is.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the following types of hardware:
+ nodes that have a link speed < PHY speed
+ 1394b PHYs that are less than S800 capable
+ 1394b/1394a adapter cable between two 1394b PHYs
Also, S1600 and S3200 are now supported if IEEE1394_SPEED_MAX is raised.
A probing function is added to nodemgr's config ROM fetching routine
which adjusts the allowable speed if an access problem was encountered.
Pros and Cons of the approach:
+ minimum code footprint to support this less widely used hardware
+ nearly no overhead for unaffected hardware
- ineffective before nodemgr began to read the ROM of affected nodes
- ineffective if ieee1394 is loaded with disable_nodemgr=1
The speed map CSRs which are published to the bus are not touched by the
patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Hakan Ardo <hakan@debian.org>
Cc: Calculex <linux@calculex.com>
Cc: Robert J. Kosinski <robk@cmcherald.com>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some old 1394-1995 SBP-2 bridges would hang if they received a broadcast write
request to BROADCAST_CHANNEL before the config ROM was read. Affected devices
include Datafab MD2-FW2 2.5" HDD and SmartDisk VST FWCDRW-V8 portable CD writer.
The write request is now directed to specific nodes instead of being broadcast
to all nodes at once, and it is only performed if a previous read request at
this register succeeded.
Fixes an old interoperability problem which was perceived as a 2.6.14-specific
regression: http://marc.theaimsgroup.com/?t=113190586800003
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
(cherry picked from 61c7f775ca commit)
After initializing an IEEE 1394 host, broadcast a resume packet. This makes
remote nodes visible which suspended their ports while the host was down.
Such nodes had to be unplugged and replugged in order to be recognized.
Motorola DCT6200 cable reciever was affected, probably other devices too.
http://marc.theaimsgroup.com/?t=113202715800001
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
(cherry picked from 14c0fa243b commit)
After a bus reset, let nodemgr call high-level update hooks first for nodes
which do not need to be probed. The main benefit is for a bus with more
than one SBP-2 device: SBP-2 reconnects will be performed before SBP-2
logins, thus have a much higher chance to succeed, and their SCSI devices
will not be blocked much longer than necessary. This was demonstrated for
Linux 2.4 by Dave Cinege a while ago.
A better approach would be to perform time-consuming probes in parallel by a
subthread. I actually plan to implement this for sbp2 but it may take a
while to get that done and tested. Until then, this tweak is a huge
improvement for users with multiple SBP-2 devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Some old 1394-1995 SBP-2 bridges would hang if they received a broadcast write
request to BROADCAST_CHANNEL before the config ROM was read. Affected devices
include Datafab MD2-FW2 2.5" HDD and SmartDisk VST FWCDRW-V8 portable CD writer.
The write request is now directed to specific nodes instead of being broadcast
to all nodes at once, and it is only performed if a previous read request at
this register succeeded.
Fixes an old interoperability problem which was perceived as a 2.6.14-specific
regression: http://marc.theaimsgroup.com/?t=113190586800003
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Introduce new macros related to phy packets and use them in ieee1394_core and
nodemgr.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
After initializing an IEEE 1394 host, broadcast a resume packet. This makes
remote nodes visible which suspended their ports while the host was down.
Such nodes had to be unplugged and replugged in order to be recognized.
Motorola DCT6200 cable reciever was affected, probably other devices too.
http://marc.theaimsgroup.com/?t=113202715800001
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Skip a superfluous pause that occured when the config ROM of a node was
scanned unsuccessfully. This also occurs if a node without link wrongly
enables its "link active" self ID flag. A GWCTech 6-port hub does this.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Units were not detected if the local IRM performed a bus reset. ("The root
node is not cycle master capable; selecting a new root node and resetting...",
often seen with iPods and other SBP-2 devices). Rearrange the order of IRM
duties and node scanning. TODO: Audit the ROM caching and parsing code for
underlying issues.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lots of this patch is trivial code cleanups (static vars were being
intialized to 0, etc).
There's also some fixes for ISO transmits (max buffer handling).
Aswell, we have a few fixes to disable IRM capabilites correctly. We've
also disabled, by default some generally unused EXPORT symbols for the
sake of cleanliness in the kernel. However, instead of removing them
completely, we felt it necessary to have a config option that allowed
them to be enabled for the many projects outside of the main kernel tree
that use our API for driver development.
The primary reason for this patch is to revert a MODE6->MODE10 RBC
conversion patch from the SCSI maintainers. The new conversions handled
directly in the scsi layer do not seem to work for SBP2. This patch
reverts to our old working code so that users can enjoy using Firewire
disks and dvd drives again.
We are working with the SCSI maintainers to resolve this issue outside
of the main kernel tree. We'll merge the patch once the SCSI layer's
handling of the MODE10 conversion is working for us.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes redundant NULL pointer checks before kfree() in all of
drivers/ieee1394/
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Nigel Cunningham
Stefan Richter
Jörn Engel
Ben Collins
Jody McIntyre
Kay Sievers
Russell King
Jody McIntyre
Olaf Hering
Ben Collins
Christoph Lameter
Yani Ioannou
gregkh@suse.de
Linus Torvalds