The device init is used to reset the accelerometer. Failure to reset
is not severe enough to stop loading the module or to resume from
hibernation. This patch relaxes failure to a warning and drops
output in case of success.
Cc: stable@kernel.org
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch add support for the MacBookAir3,1 and MacBookAir3,2 to the
applesmc driver.
[rydberg@euromail.se: minor cleanup]
Cc: stable@kernel.org
Signed-off-by: Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The owner field was removed from struct attribute in
6fd69dc578, so don't assign it anymore.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ltc4215 driver used the chip's "power good" status bit to provide
the power1_alarm file. This is wrong: the chip is really reporting the
status of one of the monitored voltages.
Change the sysfs file from power1_alarm to in2_min_alarm instead. This
matches the voltage that the chip is raising an alarm for.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Allow 1 as a valid div value as specified in the ADM1026 datasheet.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent setting fan_div from stomping on other fans that share the
same I2C register.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The manual fan speed control logic of the IT8721F is much different
from what older devices had. Update the code to properly support that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This commit fixes the following compile warnings.
From v2.6.37-rc2/m68k/m68k-allmodconfig, v2.6.37-rc2/powerpc/powerpc-randconfig:
drivers/hwmon/lis3lv02d_i2c.c:222: warning: 'lis3_i2c_runtime_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:231: warning: 'lis3_i2c_runtime_resume' defined but not used
Seen if CONFIG_PM_RUNTIME is not set.
From v2.6.37-rc2/sh4/sh-allyesconfig:
drivers/hwmon/lis3lv02d_i2c.c:191: warning: 'lis3lv02d_i2c_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:201: warning: 'lis3lv02d_i2c_resume' defined but not used
Seen if CONFIG_PM is set but CONFIG_PM_SLEEP is not.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch fixes the following compile warning.
drivers/hwmon/i5k_amb.c:500: warning: 'i5k_amb_ids' defined but not used
The warning is seen if the driver is built into the kernel (not as module).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In current implementation, the sysfs entries is not removed before return -ENODEV.
Creating the sysfs attribute should be the last thing done by the function,
after all the rest has been successful.
Otherwise there is a small window during which user-space can access the attribute
but the driver isn't ready to deal with the requests.
Fix it by moving sysfs_create_group to be the last thing done by the function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Return proper error if i2c_check_functionality reports
the adapter does not support the capability we need.
Also remove unneeded initialization for err variable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Joe Perches
Henrik Rydberg
Edgar Hucek
Maurus Cuelenaere
Linus Torvalds
Ira W. Snyder
Gabriele Gorla
Jean Delvare
Guenter Roeck
Hans J. Koch
Axel Lin