According to the DP specification the disparity of the first symbol
should always be negative. It is therefore safe to assume that panels
will conform to that and therefore parameterizing this field should
never be necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of HBLANK and VBLANK symbols can be computed at runtime so
that they can be set appropriately depending on the video mode and DP
link.
These values are used by the packet generation logic to determine how
many audio samples can be transferred during the blanking intervals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The currently hardcoded link parameters don't work on all eDP panels, so
compute the parameters at runtime depending on the mode and panel type
to allow the driver to cope with a wider variety of panels.
Note that the number of bits per pixel of the panel is still hardcoded,
but this can be addressed in a separate patch.
This is largely based on a patch by Stéphane Marchesin but the algorithm
was largely rewritten to be more readable and concise.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lanes are powered up in decreasing order. Power them down in increasing
order for consistency.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The comment above mentions link A/B but this isn't what the code does,
so let's fix that.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code currently rounds up the clock to the next MHZ, which is
rounding up a 69.5MHz clock to 70MHz on my machine. This in turn
prevents the display from syncing. Removing this rounding fixes eDP
for me.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Other output drivers set up debugfs slightly differently. Bring the SOR
driver in line with those for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Removing only the root directory will fail when there are still files in
it. Instead of manually removing all files, remove the whole directory
recursively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Doing so allows the hotplug events generated by the connector to be
properly handled by the DRM poll helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Calling the drm_helper_hpd_irq_event() helper can sleep, so instead of
invoking it directly from the interrupt handler, schedule a work queue
and run it from there.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable hardware cursor support on Tegra124. Earlier generations support
the hardware cursor to some degree as well, but not in a way that can be
generically exposed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core can now cope with drivers that don't have an associated
struct drm_bus, so the host1x implementation is no longer useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
With the recent addition of the drm_set_unique() function, devices can
now be registered without requiring a drm_bus. Add a brief description
to the DRM docbook to show how that can be achieved.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Describe how devices are registered using the drm_*_init() functions.
Adding this to docbook requires a largish set of changes to the comments
in drm_{pci,usb,platform}.c since they are doxygen-style rather than
proper kernel-doc and therefore mess with the docbook generation.
While at it, mark usage of drm_put_dev() as discouraged in favour of
calling drm_dev_unregister() and drm_dev_unref() directly.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a helper function that allows drivers to statically set the unique
name of the device. This will allow platform and USB drivers to get rid
of their DRM bus implementations and directly use drm_dev_alloc() and
drm_dev_register().
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The internal host1x_{,un}register_client() functions can potentially be
confused with public the host1x_client_{,un}register() functions.
Rename them to host1x_{add,del}_client() to remove some of the possible
confusion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 is mostly backwards-compatible with Tegra114. However, Tegra124
supports a few more features (e.g. interlacing, ...). Introduce a new
compatible string and TMDS tables to cope with these differences.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Accessing the CRC debugfs file will hang the system if the SOR is not
enabled, so make sure that it is stays enabled until the CRC has been
read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In some cases the pixel clock used to not be correct, which is why it
had to be recomputed. It turns out that the reason why it wasn't correct
is that it was used wrongly. If used correctly there's not need for the
recomputation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The shift clock divider is highly dependent on the type of output, so
push computation of it down into the output drivers. The old code used
to work merely by accident.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Program the shift clock divider in tegra_crtc_setup_clk() since that's
where the divider is computed, so passing it around can be avoided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assert the DSI controller's reset when the driver is unloaded to reduce
power consumption and to put the controller into a known state for
subsequent driver reloads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
To prevent the enable or disable operations to potentially be run
multiple times, add guards to return early when the output is already
in the targetted state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The packet sequencer needs to be programmed depending on the video mode
of the attached peripheral. Add support for non-burst video modes with
sync events (as opposed to sync pulses) and select either sequence
depending on the video mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI controllers are powered by a (typically 1.2V) regulator. Usually
this is always on, so there was no need to support enabling or disabling
it thus far. But in order not to consume any power when DSI is inactive,
give the driver a chance to enable or disable the supply as needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A bunch of registers are initialized to 0 upon during driver probe. It
turns out that none of these are actually needed, so they can simply be
dropped.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The pixel format enumeration values used by the Tegra DSI controller
don't match those defined by the DSI framework. Make sure to convert
them to the internal format before writing it to the register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
For some reason when the PW*_ENABLE and PM*_ENABLE fields are cleared
during disable, the HDMI output stops working properly. Resetting and
initializing doesn't help.
Comment out those accesses for now until it has been determined what to
do about them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Disable LVDS mode according to register documentation. It seems like
this has no effect on the operation of HDMI, but it's probably a good
idea to do this anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reflects the power-up sequence as described in the documentation,
but it doesn't seem to be strictly necessary to get HDMI to work.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clocks are never enabled or disabled in atomic context, so we can use
the clk_prepare_enable() and clk_disable_unprepare() helpers instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The generic Tegra output code already sets up the clocks properly, so
there's no need to do it again when the HDMI output is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Revert commit 18ebc0f404 "drm/tegra: hdmi: Enable VDD earlier for
hotplug/DDC" and instead add a new supply for the +5V pin on the HDMI
connector.
The vdd-supply property refers to the regulator that supplies the
AVDD_HDMI input on Tegra, rather than the +5V HDMI connector pin. This
was never a problem before, because all boards had that pin hooked up to
a regulator that was always on. Starting with Dalmore and continuing
with Venice2, the +5V pin is controllable via a GPIO. For reasons
unknown, the GPIO ended up as the controlling GPIO of the AVDD_HDMI
supply in the Dalmore and Venice2 DTS files. But that's not correct.
Instead, a separate supply must be introduced so that the +5V pin can be
controlled separately from the supplies that feed the HDMI block within
Tegra.
A new hdmi-supply property is introduced that takes the place of the
vdd-supply and vdd-supply is only enabled when HDMI is enabled rather
than all the time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Setting the bits in this register is dependent on the output type driven
by the display controller. All output drivers already set these properly
so there is no need to do it here again.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_dc_format() and tegra_dc_setup_window() functions are only
used internally by the display controller driver. Move them upwards in
order to make them static and get rid of the function prototypes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
V_DIRECTION is the name of the field in the documentation, so use that
for consistency. Also add the H_DIRECTION field for completeness.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR allows the computation of a 32 bit CRC of the content that it
transmits. This functionality is exposed via debugfs and is useful to
verify proper operation of the SOR.
Signed-off-by: Thierry Reding <treding@nvidia.com>
YUYV is UYVY with swapped bytes. Luckily the Tegra DC hardware can swap
bytes during scan-out, so supporting YUYV is simply a matter of writing
the correct value to the byteswap register.
This patch modifies tegra_dc_format() to return the byte swap parameter
via an output parameter in addition to returning the pixel format. Many
other formats can potentially be supported in a similar way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove extern keyword from function prototypes since it isn't needed and
drop an unnecessary forward declaration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thierry Reding
Stéphane Marchesin
Rob Clark
Dave Airlie