Size of be_nic_res_desc structure is incorrect. Fix it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"First Bluetooth fixes to 3.12, it includes:
* 3 patches to add device id for 3 new hardwares.
* 2 patches from Johan to fix the rfkill behaviour during setup stage
* a small clean up in the rfcomm TTY code that fixes a potential racy
condition (by Gianluca Anzolin)
* 2 fixes to proper set encryption key size and security level in the
peripheral role of Bluetooth LE devices. (by Andre Guedes)
* a fix for dealing devices where pairing is not necessary, we were keeping
the Bluetooth ACL connection alive for too much time. (by Syam Sidhardhan)"
Also, I fixed-up an curly-brace indentation problem in the Bluetooth
code while merging. On top of that...
Alexey Khoroshilov brings a p54usb fix to avoid a resource leak when
request_firmware_nowait fails.
Amitkumar Karwar fixes a firmware hang caused by too much header data
being appended for USB devices using the mwifiex driver.
Arend van Spriel provides three fixes: a brcmfmac fix to relocate some
driver code outside of an .init section; a scheduling while atomic
fix for bcma; and, another scheduling while atomic fix for brcmsmac.
Bing Zhao offers a pair of mwifiex fixes: a code change to avoid
firmware timeouts on USB; and a fix for a NULL pointer dereference.
Christian Lamparter adds a device ID to p54usb.
Felix Fietkau implements a quartet of small ath9k fixes, including
a locking fix, a list management fix, a fix to properly mark a stale
buffer, and an aggregate buffering fix.
Larry Finger champions a data alignment fix to make rtlwifi work
better with ARM builds.
Solomon Peachy reverts an earlier interrupt handling fix for cw1200
and replaces it with a new threaded oneshot irq handler implementation.
Sujith Manoharan fixes an ath9k regression by reverting an earlier
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver is used on PowerPC which don't provide writel_relaxed(). This
breaks the c2k and prpmc2800 default configurations. To fix the build,
turn the calls to writel_relaxed() into writel(). The impacts for ARM
should be minimal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some functions and variables are only used if the configuration selects
HAVE_CLK. Protect them with a corresponding #ifdef CONFIG_HAVE_CLK block
to avoid compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[wsa: added marker to #endif]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit d16933b339 "i2c: s3c2410: Move
location of clk_prepare_enable() call in probe function" refactored
clk_enable and clk_disable calls yet neglected to remove the
clk_disable_unprepare call in the module's remove().
It helps remove warnings on an arndale during unbind:
echo 12c90000.i2c > /sys/bus/platform/devices/12c90000.i2c/driver/unbind
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:842 clk_disable+0x18/0x24()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Not tainted 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c4a64>] (clk_disable+0x18/0x24)
[<c02c4a64>] (clk_disable+0x18/0x24) from [<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70)
[<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a6 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:751 clk_unprepare+0x14/0x1c()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Tainted: G W 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c5834>] (clk_unprepare+0x14/0x1c)
[<c02c5834>] (clk_unprepare+0x14/0x1c) from [<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70)
[<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a7 ]---
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Recent movement of all configurations of pin in the single call of
pin_config_set(), it is aborting configuration if BIAS_PULL_PIN_DEFAULT
is selected as return of configuration.
The original idea was to just avoid any update on register for pull up/down
configuration if this option is selected.
Fixing this by just bypassing any register update for BIAS_PULL_PIN_DEFAULT
and continuing the remaining configuration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As documented in Application Note SWPA117 v2.1(NDA), LDO override has a
requirement that when switching from Bias active + override active
mode(FBB/RBB) to Bypass(nominal) mode, LDO reset must be performed
*after* LDO transitions to Bypass(nominal) mode.
The same rule in reverse applies when switching from a ABB bypass mode
to ABB enabled - LDO override *must* be performed prior to transition to
required ABB mode, if we do not do that, the same glitch takes place.
Currently while transitioning to ABB bypass, we reset the LDO overide
prior to the transition which causes a few milliseconds where ABB LDO
voltage could go all the way to 800mV(based on SoC process node),
during this period, the delta voltage between VDD rail and VBB rail
could cause the system to improperly function.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Values of pins in table s5pv210 bank are incorrect. This patch correct values.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise we may try to start transfers immediately and then fail to
runtime resume the device causing us not to have clocks enabled.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Conflicts:
drivers/spi/spi-s3c64xx.c
coccicheck shows:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment
Fix each of them with a *a = *b;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.
A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.
v2: fix post increment bug in return
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.
This allows for clean up of the return types that were previously
converted to int.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches clean up a loop flow.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, we should be using
foo = alloc(...)
if (!foo)
return -ENOMEM;
return 0;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add back 82580 loopback tests to ethtool.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the datasheet for Micron n25q256a (N25Q256A13ESF40F) 4-byte
addressing mode should be entered as follows:
<quote>
To enter or exit the 4-byte address mode, the WRITE ENABLE command
must be executed to set the write enable latch bit to 1. (Note: The
WRITE ENABLE command must NOT be executed on the N25Q256A83ESF40x and
N25Q256A83E1240x devices.) S# must be driven LOW. The effect of the
command is immediate; after the command has been executed, the write
enable latch bit is cleared to 0.
</quote>
Micron's portable way to perform this for all types of Micron flash
is to first issue a write enable, then switch the addressing mode
followed by a write disable to avoid leaving the flash in a write-
able state.
Signed-off-by: Elie De Brauwer <eliedebrauwer@email.com>
[Brian: reworked a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes a memory leak in the ONFI support code for detecting the
required ECC levels from this commit:
commit 6dcbe0cdd8
Author: Huang Shijie <b32955@freescale.com>
Date: Wed May 22 10:28:27 2013 +0800
mtd: get the ECC info from the Extended Parameter Page
In the success case, we never freed the 'ep' buffer.
Also, this fixes an oversight in the same commit where we (harmlessly)
freed the NULL pointer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
devm_clk_get() is used so there is no reason to explicitly
call clk_put() in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bunch of failure exits in ffs_fs_mount() with
seriously broken recovery logics. Most of that appears to stem
from misunderstanding of the ->kill_sb() semantics; unlike
->put_super() it is called for *all* superblocks of given type,
no matter how (in)complete the setup had been. ->put_super()
is called only if ->s_root is not NULL; any failure prior to
setting ->s_root will have the call of ->put_super() skipped.
->kill_sb(), OTOH, awaits every superblock that has come from
sget().
Current behaviour of ffs_fs_mount():
We have struct ffs_sb_fill_data data on stack there. We do
ffs_dev = functionfs_acquire_dev_callback(dev_name);
and store that in data.private_data. Then we call mount_nodev(),
passing it ffs_sb_fill() as a callback. That will either fail
outright, or manage to call ffs_sb_fill(). There we allocate an
instance of struct ffs_data, slap the value of ffs_dev (picked
from data.private_data) into ffs->private_data and overwrite
data.private_data by storing ffs into an overlapping member
(data.ffs_data). Then we store ffs into sb->s_fs_info and attempt
to set the rest of the things up (root inode, root dentry, then
create /ep0 there). Any of those might fail. Should that
happen, we get ffs_fs_kill_sb() called before mount_nodev()
returns. If mount_nodev() fails for any reason whatsoever,
we proceed to
functionfs_release_dev_callback(data.ffs_data);
That's broken in a lot of ways. Suppose the thing has failed in
allocation of e.g. root inode or dentry. We have
functionfs_release_dev_callback(ffs);
ffs_data_put(ffs);
done by ffs_fs_kill_sb() (ffs accessed via sb->s_fs_info), followed by
functionfs_release_dev_callback(ffs);
from ffs_fs_mount() (via data.ffs_data). Note that the second
functionfs_release_dev_callback() has every chance to be done to freed memory.
Suppose we fail *before* root inode allocation. What happens then?
ffs_fs_kill_sb() doesn't do anything to ffs (it's either not called at all,
or it doesn't have a pointer to ffs stored in sb->s_fs_info). And
functionfs_release_dev_callback(data.ffs_data);
is called by ffs_fs_mount(), but here we are in nasal daemon country - we
are reading from a member of union we'd never stored into. In practice,
we'll get what we used to store into the overlapping field, i.e. ffs_dev.
And then we get screwed, since we treat it (struct gfs_ffs_obj * in
disguise, returned by functionfs_acquire_dev_callback()) as struct
ffs_data *, pick what would've been ffs_data ->private_data from it
(*well* past the actual end of the struct gfs_ffs_obj - struct ffs_data
is much bigger) and poke in whatever it points to.
FWIW, there's a minor leak on top of all that in case if ffs_sb_fill()
fails on kstrdup() - ffs is obviously forgotten.
The thing is, there is no point in playing all those games with union.
Just allocate and initialize ffs_data *before* calling mount_nodev() and
pass a pointer to it via data.ffs_data. And once it's stored in
sb->s_fs_info, clear data.ffs_data, so that ffs_fs_mount() knows that
it doesn't need to kill the sucker manually - from that point on
we'll have it done by ->kill_sb().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: stable <stable@vger.kernel.org> # 3.3+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put_device(dev) at the bottom of the loop of device_shutdown
may result in the dev being cleaned up. In device_create_release,
the dev is kfreed.
However, device_shutdown attempts to use the dev pointer again after
put_device by referring to dev->parent.
Copy the parent pointer instead to avoid this condition.
This bug was found on Chromium OS's chromeos-3.8, which is based on v3.8.11.
See bug report : https://code.google.com/p/chromium/issues/detail?id=297842
This can easily be reproduced when shutting down with
hidraw devices that report battery condition.
Two examples are the HP Bluetooth Mouse X4000b and the Apple Magic Mouse.
For example, with the magic mouse :
The dev in question is "hidraw0"
dev->parent is "magicmouse"
In the course of the shutdown for this device, the input event cleanup calls
a put on hidraw0, decrementing its reference count.
When we finally get to put_device(dev) in device_shutdown, kobject_cleanup
is called and device_create_release does kfree(dev).
dev->parent is no longer valid, and we may crash in
put_device(dev->parent).
This change should be applied on any kernel with this change :
d1c6c030fc
Cc: stable@vger.kernel.org
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 666b9adc80 terminated vmbus
version negotiation incorrectly. We need to terminate the version
negotiation only if the current negotiation were to timeout.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <ohering@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not correctly negotiate the version numbers for the util
driver when hosted on earlier hosts. The version numbers presented by this
driver were not compatible with the version numbers supported by Windows Server
2008. Fix this problem.
I would like to thank Olaf Hering (ohering@suse.com) for identifying the problem.
Reported-by: Olaf Hering <ohering@suse.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unset init_clients_timer and amthif_stall_timers
in mei_reset in order to cancel timer ticking and hence
avoid recursive reset calls.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bus layer omitted check for client state transition while waiting
for read completion
The client state transition may occur for example as result
of firmware initiated reset
Add mei_cl_is_transitioning wrapper to reduce the code
repetition.:
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. u8 counters are prone to hard to detect overflow:
make them unsigned long to match bit_ functions argument type
2. don't check me_clients_num for negativity, it is unsigned.
3. init all the me client counters from one place
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).
Peter Boström noticed and reported the bug.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For controller versions greater than 1.6, setting ULPI_PHY_CLK_SEL
bit when USB_EN bit is already set causes instability issues with
PHY_CLK_VLD bit. So USB_EN is set only for IP controller version
below 1.6 before setting ULPI_PHY_CLK_SEL bit
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses platform_driver_probe() to obtain platform data
if any. However, that function is placed in the .init section so
it must be called upon driver module initialization.
The problem was reported by Fenguang Wu resulting in a kernel
oops because the .init section was already freed.
[ 48.966342] Switched to clocksource tsc
[ 48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[ 48.970851] BUG: unable to handle kernel paging request at ffffffff82196446
[ 48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163
[ 48.970957] Oops: 0011 [#1]
[ 48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23
[ 48.970957] Workqueue: events brcmf_driver_init
[ 48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000
[ 48.970957] RIP: 0010:[<ffffffff82196446>] [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP: 0000:ffff8800001d5d40 EFLAGS: 00000286
[ 48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000
[ 48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0
[ 48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002
[ 48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0
[ 48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300
[ 48.970957] FS: 0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000
[ 48.970957] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0
[ 48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[ 48.970957] Stack:
[ 48.970957] ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9
[ 48.970957] ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8
[ 48.970957] 0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000
[ 48.970957] Call Trace:
[ 48.970957] [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70
[ 48.970957] [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10
[ 48.970957] [<ffffffff81073dc5>] process_one_work+0x1d5/0x480
[ 48.970957] [<ffffffff81073d68>] ? process_one_work+0x178/0x480
[ 48.970957] [<ffffffff81074188>] worker_thread+0x118/0x3a0
[ 48.970957] [<ffffffff81074070>] ? process_one_work+0x480/0x480
[ 48.970957] [<ffffffff8107aa17>] kthread+0xe7/0xf0
[ 48.970957] [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
[ 48.970957] RIP [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP <ffff8800001d5d40>
[ 48.970957] CR2: ffffffff82196446
[ 48.970957] ---[ end trace 62980817cd525f14 ]---
Cc: <stable@vger.kernel.org> # 3.10.x, 3.11.x
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
[ 2.883807] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000048
[ 2.883813] IP: [<ffffffff815a65e0>] pfifo_fast_enqueue+0x90/0x90
[ 2.883834] CPU: 1 PID: 3220 Comm: kworker/u8:90 Not tainted
3.11.1-monotone-l0 #6
[ 2.883834] Hardware name: Microsoft Corporation Surface with
Windows 8 Pro/Surface with Windows 8 Pro,
BIOS 1.03.0450 03/29/2013
On Surface Pro, suspend to ram gives a NULL pointer dereference in
pfifo_fast_enqueue(). The stack trace reveals that the offending
call is clearing carrier in mwifiex_usb suspend handler.
Since commit 1499d9f "mwifiex: don't drop carrier flag over suspend"
has removed the carrier flag handling over suspend/resume in SDIO
and PCIe drivers, I'm removing it in USB driver too. This also fixes
the bug for Surface Pro.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
We have 4 bytes of interface header for packets delivered to SDIO
and PCIe, but not for USB interface.
In Tx AMSDU case, currently 4 bytes of garbage data is unnecessarily
appended for USB packets. This sometimes leads to a firmware hang,
because it may not interpret the data packet correctly.
Problem is fixed by removing this redundant headroom for USB.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added USB ID for Corega WLUSB2GTST USB adapter.
Cc: <stable@vger.kernel.org>
Reported-by: Joerg Kalisch <the_force@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This supercedes the older patch ("cw1200: Don't perform SPI transfers in
interrupt context") that badly attempted to fix this problem.
This is a far simpler solution, which has the added benefit of
actually working.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit aec8e88c94.
This solution turned out to cause interrupt delivery problems, and
rather than trying to fix this approach, it has been scrapped in favor
of an alternative (and far simpler) implementation.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For pcie8897, the hs_cfg cancel command (0xe5) times out when host
comes out of suspend. This is caused by an incompleted host sleep
handshake between driver and firmware.
Like SDIO interface, PCIe also needs to go through firmware power
save events to complete the handshake for host sleep configuration.
Only USB interface doesn't require power save events for hs_cfg.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.
Reported-by: Jason Andrews <jasona@cadence.com>
Tested-by: Jason Andrews <jasona@cadence.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevents race conditions when un-aggregated frames are pending in the
driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If request_firmware_nowait() fails in p54u_load_firmware(),
p54u_load_firmware_cb is not called and no one decrements usb_dev refcnt.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When .release_buffered_frames was implemented, only A-MPDU packets were
buffered internally. Now that this has changed, the BUF_AMPDU flag needs
to be checked before calling ath_tx_addto_baw
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Optimize LNA check" tried
to use the "rs_firstaggr" flag to optimize the LNA
combining algorithm when processing subframes in
an A-MPDU. This doesn't appear to work well in practice,
so revert it and use the old method of relying on
"rs_moreaggr".
Cc: stable@vger.kernel.org # 3.11
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This might trip up tx completion processing, although the condition that
triggers this should not (yet) occur in practice.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a regression from commit
"ath9k: shrink a few data structures by reordering fields"
When cloning a buffer, the stale flag (part of bf_state now) needs to be
reset after copying the state to prevent tx processing hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After reports from Chris and Josh Boyer of a rare crash in applesmc,
Guenter pointed at the initialization problem fixed below. The patch
has not been verified to fix the crash, but should be applied
regardless.
Reported-by: <jwboyer@fedoraproject.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
of_get_display_timing(s) use of_find_node_by_name
to get child node, this is incorrect, of_get_child_by_name
should be used instead. The patch fixes it.
Small typo is also corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
udev has this nice feature of creating "dead" /dev/<node> device-nodes if
it finds a devnode:<node> modalias. Once the node is accessed, the kernel
automatically loads the module that provides the node. However, this
requires udev to know the major:minor code to use for the node. This
feature was introduced by:
commit 578454ff7e
Author: Kay Sievers <kay.sievers@vrfy.org>
Date: Thu May 20 18:07:20 2010 +0200
driver core: add devname module aliases to allow module on-demand auto-loading
However, uhid uses dynamic minor numbers so this doesn't actually work. We
need to load uhid to know which minor it's going to use.
Hence, allocate a static minor (just like uinput does) and we're good
to go.
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix to return -EINVAL when virtual vertical size smaller than real
instead of 0, as done elsewhere in this function. Also remove dup code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The nice thing about devm_* is that the driver doesn't need to free the
resources but the driver core takes care about that. This also
simplifies the error path quite a bit and removes the wrong check for a
clock pointer being NULL.
Russell King - ARM Linux <linux@arm.linux.org.uk>:
"And this patch also fixes the above: disabling/unpreparing _after_ putting
the thing - which was quite silly... :)"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI-CM driver uses the backlight class so needs to build depend on it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 'e7f3880cd9b98c5bf9391ae7acdec82b75403776'
tty: Fix recursive deadlock in tty_perform_flush()
introduced a regression where tcflush() does not generate
SIGTTOU for background process groups.
Make sure ioctl(TCFLSH) calls tty_check_change() when
invoked from the line discipline.
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the STI driver by setting cpu_possible_mask to make EMEV2
SMP work as expected together with the ARM broadcast timer.
This breakage was introduced by:
f7db706 ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real hardware clock-event
Without this fix SMP operation is broken on EMEV2 since no
broadcast timer interrupts trigger on the secondary CPU cores.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Trying to read data from the Pegasus Technologies NoteTaker (0e20:0101)
[1] with the Windows App (EasyNote) works natively but fails when
Windows is running under KVM (and the USB device handed to KVM).
The reason is a USB control message
usb 4-2.2: control urb: bRequestType=22 bRequest=09 wValue=0200 wIndex=0001 wLength=0008
This goes to endpoint address 0x01 (wIndex); however, endpoint address
0x01 does not exist. There is an endpoint 0x81 though (same number,
but other direction); the app may have meant that endpoint instead.
The kernel thus rejects the IO and thus we see the failure.
Apparently, Linux is more strict here than Windows ... we can't change
the Win app easily, so that's a problem.
It seems that the Win app/driver is buggy here and the driver does not
behave fully according to the USB HID class spec that it claims to
belong to. The device seems to happily deal with that though (and
seems to not really care about this value much).
So the question is whether the Linux kernel should filter here.
Rejecting has the risk that somewhat non-compliant userspace apps/
drivers (most likely in a virtual machine) are prevented from working.
Not rejecting has the risk of confusing an overly sensitive device with
such a transfer. Given the fact that Windows does not filter it makes
this risk rather small though.
The patch makes the kernel more tolerant: If the endpoint address in
wIndex does not exist, but an endpoint with toggled direction bit does,
it will let the transfer through. (It does NOT change the message.)
With attached patch, the app in Windows in KVM works.
usb 4-2.2: check_ctrlrecip: process 13073 (qemu-kvm) requesting ep 01 but needs 81
I suspect this will mostly affect apps in virtual environments; as on
Linux the apps would have been adapted to the stricter handling of the
kernel. I have done that for mine[2].
[1] http://www.pegatech.com/
[2] https://sourceforge.net/projects/notetakerpen/
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It needs to free ci->hw_bank.regmap explicitly since it is not managed
resource.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clocksource devices provided by DT can be disabled (status != "okay").
Instead of registering clocksource drivers for disabled nodes, respect
the device's status by skiping disabled nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Some variants of Exynos MCT, namely exynos4210-mct at the moment, use
normal, shared interrupts for local timers. This means that each
interrupt must have correct affinity set to fire only on CPU
corresponding to given local timer.
However after recent conversion of clocksource drivers to not use the
local timer API for local timer initialization any more, the point of
time when local timers get initialized changed and irq_set_affinity()
fails because the CPU is not marked as online yet.
This patch fixes this by moving the call to irq_set_affinity() to
CPU_ONLINE notification, so the affinity is being set when the CPU goes
online.
This fixes a regression introduced by commit
ee98d27df6 ARM: EXYNOS4: Divorce mct from local timer API
which rendered all Exynos4210 based boards unbootable due to
failing irq_set_affinity() making local timers inoperatible.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This commit:
573145f08c
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
replaced a call to the driver's timer initialization by a call to
clocksource_of_init(). However, it failed to select CONFIG_CLKSRC_OF.
Fix this by selecting CONFIG_CLKSRC_OF for Armada370/XP machines.
Without this change the kernel is stuck at: 'Calibrating delay loop...'.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in ohci-hcd. The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does. Rather, it
depends on the hardware adding completed TDs to a "done queue". Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place. As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.
To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired). Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way. If so, it gives back the next URB right away.
This should be applied to all kernels containing commit 815fa7b917
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in uhci-hcd. It should be
applied to all kernels containing commit c44b225077 (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it. As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set. I don't have any way to test this change,
unfortunately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit b5dc0d10 (drm/imx: kill firstopen callback) the following probe
failure is seen:
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] Initialized imx-drm 1.0.0 20120507 on minor 0
imx-ldb ldb.10: adding encoder failed with -16
imx-ldb: probe of ldb.10 failed with error -16
imx-ipuv3 2400000.ipu: IPUv3H probed
imx-ipuv3 2800000.ipu: IPUv3H probed
imx-ipuv3-crtc imx-ipuv3-crtc.0: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.0 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.1: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.1 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.2: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.2 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.3: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.3 failed with error -16
The reason for the probe failure is that now 'imxdrm->references' is incremented
early in imx_drm_driver_load(), so the following checks in imx_drm_add_crtc()
and imx_drm_add_encoder():
if (imxdrm->references) {
ret = -EBUSY;
goto err_busy;
}
,will always fail.
Instead of manually keeping the references in the imx-drm driver, let's use
drm->open_count.
After this patch, lvds panel is functional on a mx6qsabrelite board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't allow entry to iwctl_siwencodeext if device not open.
This fixes a race condition where wpa supplicant/network manager
enters the function when the device is already closed.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt6656 is prone to resetting on the usb bus.
It seems there is a race condition and wpa supplicant is
trying to open the device via iw_handlers before its actually
closed at a stage that the buffers are being removed.
The device is longer considered open when the
buffers are being removed. So move ~DEVICE_FLAGS_OPENED
flag to before freeing the device buffers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be race condition that the device is ndo_start_xmit
at a point where the device is closing and apTD is NULL resulting
in dead lock.
Add a NULL check to apTD and return NULL to calling functions.
This is more likely on 64 bit systems.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking the return of dev_alloc_skb as stated in the following bug: https://bugzilla.kernel.org/show_bug.cgi?id=60411
Signed-off-by: Iker Pedrosa <ikerpedrosam@gmail.com>
Reported-by: RUC_Soft_Sec rucsoftsec@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix PV spinlocks triggering jump_label code bug
- Remove extraneous code in the tpm front driver
- Fix ballooning out of pages when non-preemptible
- Fix deadlock when using a 32-bit initial domain with large amount of memory.
- Add xen_nopvpsin parameter to the documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQvzCAAoJEFjIrFwIi8fJyCIIAMENABapdLhrOiRdQ1Y7T5v1
4bogPDLwpVxHzwo/vnHcNpl35/dUZrC6wQa51Bkoqq0V8o1XmjFy3SY/EBGjEAvw
hh4qxGY0p0NNi6hKrWC8mH9u2TcluZGm1uecabkXUhl9mrAB5oBsfJdbBZ5N69gO
QXXt0j7Xwv1APwH86T0e1Lz+lulhdw2ItXP4osYkEbRYNSaaGnuwsd0Jxcb4DeMk
qhKgP7QMn3C7zDDaapJo1axeYQRBNEtv5M8+0wwMleX4yX1+IBRZeQTsRfMr7RB/
8FhssWiH15xU6Gmzgi/VR8xhTEIbQh5GWsVReGf6pqIYSxGSYTvvyhm0bVRH4JI=
=c+7u
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes and one update to the kernel-paramters.txt documentation.
- Fix PV spinlocks triggering jump_label code bug
- Remove extraneous code in the tpm front driver
- Fix ballooning out of pages when non-preemptible
- Fix deadlock when using a 32-bit initial domain with large amount
of memory
- Add xen_nopvpsin parameter to the documentation"
* tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/spinlock: Document the xen_nopvspin parameter.
xen/p2m: check MFN is in range before using the m2p table
xen/balloon: don't alloc page while non-preemptible
xen: Do not enable spinlocks before jump_label_init() has executed
tpm: xen-tpmfront: Remove the locality sysfs attribute
tpm: xen-tpmfront: Fix default durations
In
commit 81e49f8114
Author: Glauber Costa <glommer@openvz.org>
Date: Wed Aug 28 10:18:13 2013 +1000
i915: bail out earlier when shrinker cannot acquire mutex
SHRINK_STOP was added to tell the core shrinker code to bail out and
go to the next shrinker since the i915 shrinker couldn't acquire
required locks. But the SHRINK_STOP return code was added to the
->count_objects callback and not the ->scan_objects callback as it
should have been, resulting in tons of dmesg noise like
shrink_slab: i915_gem_inactive_scan+0x0/0x9c negative objects to delete nr=-xxxxxxxxx
Fix discusssed with Dave Chinner.
References: http://www.spinics.net/lists/intel-gfx/msg33597.html
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Glauber Costa <glommer@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning target
to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps fix
a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but relatively
little memory. To responsibly select a smaller value users should use
the new nr_bios tracepoint info (via commit 75afb352 "block: Add nr_bios
to block_rq_remap tracepoint") to determine the peak number of bios
their workloads create.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMVHAAoJEMUj8QotnQNaOXgIAJS6/XJKMoHfiDJ9M+XD34rZ
Uyr9TEnubX3DKCRBiY23MUcCQn3fx6BjCGv5/c8L4jQFIuLyDi2yatqpwXcbGSJh
G/S/y6u0Axek+ew7TS80OFop4nblW6MoKnoh9/4N55Ofa+1WvKM4ERUGjHGbauyS
TxmLQPToCFPLYRIOZ+imd6hQuIZ1+FFdJFvi7kY9O6Llx2sLD6fWi1iruBd/Da2H
ByMX3biGN45mSpcBzRbSC/FkJ9CRIvT9n82BDPS0o3Tllt8NaVlEDaovB7h4ncc0
bFuT2Z3Q38B9uZ8Lj0bqdGzv3kXMLCkLo6WhWjyUt84hmDPAzRpBwt60jUqWyZs=
=bjVp
-----END PGP SIGNATURE-----
Merge tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning
target to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps
fix a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but
relatively little memory. To responsibly select a smaller value users
should use the new nr_bios tracepoint info (via commit 75afb352
"block: Add nr_bios to block_rq_remap tracepoint") to determine the
peak number of bios their workloads create"
* tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: add reserved_bio_based_ios module parameter
dm: add reserved_rq_based_ios module parameter
dm: lower bio-based mempool reservation
dm thin: do not expose non-zero discard limits if discards disabled
dm mpath: disable WRITE SAME if it fails
dm-snapshot: fix performance degradation due to small hash size
dm snapshot: workaround for a false positive lockdep warning
dm stats: fix possible counter corruption on 32-bit systems
dm mpath: do not fail path on -ENOSPC
In gadget mode, musb->is_active should be set only when connected to the
host. musb_g_reset() already takes care of it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
My old @it.uu.se email address is going away, so update relevant
files to point to my @gmail.com address instead. In sata_promise.c
just delete the address, people can get it from MAINTAINERS.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If 'dvfs_info' is NULL (due to devm_kzalloc failure) the failure
error message would try to dereference it. Use 'pdev' instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_get() can be called from external drivers which might not be aware if
cpufreq driver is registered or not. And so we should actually check if cpufreq
driver is registered or not and also if cpufreq is active or disabled, at the
beginning of cpufreq_get().
Otherwise call to lock_policy_rwsem_read() might hit BUG_ON(!policy).
Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the hw supports intel_pstate and acpi_cpufreq, intel_pstate will
get loaded first.
acpi_cpufreq_init() will call acpi_cpufreq_early_init()
and that will allocate perf data and init those perf data in ACPI core,
(that will cover all CPUs). But later it will free them as
cpufreq_register_driver(acpi_cpufreq) will fail as intel_pstate is
already registered
Use cpufreq_get_current_driver() to check if we can skip the
acpi_cpufreq loading.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes the issues indicated by the test results that
ipmi_msg_handler() is invoked in atomic context.
BUG: scheduling while atomic: kipmi0/18933/0x10000100
Modules linked in: ipmi_si acpi_ipmi ...
CPU: 3 PID: 18933 Comm: kipmi0 Tainted: G AW 3.10.0-rc7+ #2
Hardware name: QCI QSSC-S4R/QSSC-S4R, BIOS QSSC-S4R.QCI.01.00.0027.070120100606 07/01/2010
ffff8838245eea00 ffff88103fc63c98 ffffffff814c4a1e ffff88103fc63ca8
ffffffff814bfbab ffff88103fc63d28 ffffffff814c73e0 ffff88103933cbd4
0000000000000096 ffff88103fc63ce8 ffff88102f618000 ffff881035c01fd8
Call Trace:
<IRQ> [<ffffffff814c4a1e>] dump_stack+0x19/0x1b
[<ffffffff814bfbab>] __schedule_bug+0x46/0x54
[<ffffffff814c73e0>] __schedule+0x83/0x59c
[<ffffffff81058853>] __cond_resched+0x22/0x2d
[<ffffffff814c794b>] _cond_resched+0x14/0x1d
[<ffffffff814c6d82>] mutex_lock+0x11/0x32
[<ffffffff8101e1e9>] ? __default_send_IPI_dest_field.constprop.0+0x53/0x58
[<ffffffffa09e3f9c>] ipmi_msg_handler+0x23/0x166 [ipmi_si]
[<ffffffff812bf6e4>] deliver_response+0x55/0x5a
[<ffffffff812c0fd4>] handle_new_recv_msgs+0xb67/0xc65
[<ffffffff81007ad1>] ? read_tsc+0x9/0x19
[<ffffffff814c8620>] ? _raw_spin_lock_irq+0xa/0xc
[<ffffffffa09e1128>] ipmi_thread+0x5c/0x146 [ipmi_si]
...
Also Tony Camuso says:
We were getting occasional "Scheduling while atomic" call traces
during boot on some systems. Problem was first seen on a Cisco C210
but we were able to reproduce it on a Cisco c220m3. Setting
CONFIG_LOCKDEP and LOCKDEP_SUPPORT to 'y' exposed a lockdep around
tx_msg_lock in acpi_ipmi.c struct acpi_ipmi_device.
=================================
[ INFO: inconsistent lock state ]
2.6.32-415.el6.x86_64-debug-splck #1
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/3/17 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&ipmi_device->tx_msg_lock){+.?...}, at: [<ffffffff81337a27>] ipmi_msg_handler+0x71/0x126
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810ba11c>] __lock_acquire+0x63c/0x1570
[<ffffffff810bb0f4>] lock_acquire+0xa4/0x120
[<ffffffff815581cc>] __mutex_lock_common+0x4c/0x400
[<ffffffff815586ea>] mutex_lock_nested+0x4a/0x60
[<ffffffff8133789d>] acpi_ipmi_space_handler+0x11b/0x234
[<ffffffff81321c62>] acpi_ev_address_space_dispatch+0x170/0x1be
The fix implemented by this change has been tested by Tony:
Tested the patch in a boot loop with lockdep debug enabled and never
saw the problem in over 400 reboots.
Reported-and-tested-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge fixes from Andrew Morton:
"Bunch of fixes.
And a reversion of mhocko's "Soft limit rework" patch series. This is
actually your fault for opening the merge window when I was off racing ;)
I didn't read the email thread before sending everything off.
Johannes Weiner raised significant issues:
http://www.spinics.net/lists/cgroups/msg08813.html
and we agreed to back it all out"
I clearly need to be more aware of Andrew's racing schedule.
* akpm:
MAINTAINERS: update mach-bcm related email address
checkpatch: make extern in .h prototypes quieter
cciss: fix info leak in cciss_ioctl32_passthru()
cpqarray: fix info leak in ida_locked_ioctl()
kernel/reboot.c: re-enable the function of variable reboot_default
audit: fix endless wait in audit_log_start()
revert "memcg, vmscan: integrate soft reclaim tighter with zone shrinking code"
revert "memcg: get rid of soft-limit tree infrastructure"
revert "vmscan, memcg: do softlimit reclaim also for targeted reclaim"
revert "memcg: enhance memcg iterator to support predicates"
revert "memcg: track children in soft limit excess to improve soft limit"
revert "memcg, vmscan: do not attempt soft limit reclaim if it would not scan anything"
revert "memcg: track all children over limit in the root"
revert "memcg, vmscan: do not fall into reclaim-all pass too quickly"
fs/ocfs2/super.c: use a bigger nodestr in ocfs2_dismount_volume
watchdog: update watchdog_thresh properly
watchdog: update watchdog attributes atomically
The arg64 struct has a hole after ->buf_size which isn't cleared. Or if
any of the calls to copy_from_user() fail then that would cause an
information leak as well.
This was assigned CVE-2013-2147.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pciinfo struct has a two byte hole after ->dev_fn so stack
information could be leaked to the user.
This was assigned CVE-2013-2147.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge bcache fixes from Kent Overstreet:
"There's fixes for _three_ different data corruption bugs, all of which
were found by users hitting them in the wild.
The first one isn't bcache specific - in 3.11 bcache was switched to
the bio_copy_data in fs/bio.c, and that's when the bug in that code
was discovered, but it's also used by raid1 and pktcdvd. (That was my
code too, so the bug's doubly embarassing given that it was or
should've been just a cut and paste from bcache code. Dunno what
happened there).
Most of these (all the non data corruption bugs, actually) were ready
before the merge window and have been sitting in Jens' tree, but I
don't know what's been up with him lately..."
* emailed patches from Kent Overstreet <kmo@daterainc.com>:
bcache: Fix flushes in writeback mode
bcache: Fix for handling overlapping extents when reading in a btree node
bcache: Fix a shrinker deadlock
bcache: Fix a dumb CPU spinning bug in writeback
bcache: Fix a flush/fua performance bug
bcache: Fix a writeback performance regression
bcache: Correct printf()-style format length modifier
bcache: Fix for when no journal entries are found
bcache: Strip endline when writing the label through sysfs
bcache: Fix a dumb journal discard bug
block: Fix bio_copy_data()
In writeback mode, when we get a cache flush we need to make sure we
issue a flush to the backing device.
The code for sending down an extra flush was wrong - by cloning the bio
we were probably getting flags that didn't make sense for a bare flush,
and also the old code was firing for FUA bios, for which we don't need
to send a flush to the backing device.
This was causing data corruption somehow - the mechanism was never
determined, but this patch fixes it for the users that were seeing it.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
btree_sort_fixup() was overly clever, because it was trying to avoid
pulling a key off the btree iterator in more than one place.
This led to a really obscure bug where we'd break early from the loop in
btree_sort_fixup() if the current key overlapped with keys in more than
one older set, and the next key it overlapped with was zero size.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GFP_NOIO means we could be getting called recursively - mca_alloc() ->
mca_data_alloc() - definitely can't use mutex_lock(bucket_lock) then.
Whoops.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bch_journal_meta() was missing the flush to make the journal write
actually go down (instead of waiting up to journal_delay_ms)...
Whoops
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background writeback works by scanning the btree for dirty data and
adding those keys into a fixed size buffer, then for each dirty key in
the keybuf writing it to the backing device.
When read_dirty() finishes and it's time to scan for more dirty data, we
need to wait for the outstanding writeback IO to finish - they still
take up slots in the keybuf (so that foreground writes can check for
them to avoid races) - without that wait, we'll continually rescan when
we'll be able to add at most a key or two to the keybuf, and that takes
locks that starves foreground IO. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix
drivers/md/bcache/btree.c: In function ‘bch_btree_node_read’:
drivers/md/bcache/btree.c:259: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 3 has type ‘size_t’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The journal replay code didn't handle this case, causing it to go into
an infinite loop...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sysfs attributes with unusual characters have crappy failure modes
in Squeeze (udev 164); later versions of udev are unaffected.
This should make these characters more unusual.
Signed-off-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
That switch statement was obviously wrong, leading to some sort of weird
spinning on rare occasion with discards enabled...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_balloon_scratch_page() disables preemption so we cannot call
alloc_page() in between get/put_balloon_scratch_page(). Shuffle bits
around in decrease_reservation() to avoid this.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Upon deeper review it was agreed to remove the driver-unique
'locality' sysfs attribute before it is present in a released
kernel.
The attribute was introduced in e2683957fb
during the 3.12 merge window, so this patch needs to go in before
3.12 is released.
The hope is to have a well defined locality API that all the other
locality aware drivers can use, perhaps in 3.13.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
All the default durations were being set to 10 minutes which is
way too long for the timeouts. Normal values for the longest
duration are around 5 mins, and short duration ar around .5s.
Further, these are just the default, tpm_get_timeouts will set
them to values from the TPM (or throw an error).
Just remove them.
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This regression has been introduced in
commit 9f11a9e4e5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 13 00:54:58 2013 +0200
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
Ville brough up the idea that this is just the pipe A quirk gone
wrong.
Note that after resume the bios might or might not have enabled pipe A
already. We have a bit of magic to make sure that on resume we set up
a decent mode for pipe A, but I fear if I just smash pipe A to always
on we'd enable it in a bogus state and hang the hw. Hence the
readback.
v2: Clarify the logic a bit as suggested by Chris. Also amend the
commit message to clarify why we don't unconditionally enable the
pipe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66462
References: https://lkml.org/lkml/2013/8/26/238
Cc: Meelis Roos <mroos@ut.ee>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use |= instead of = as suggested by Chris.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The native TV encoder has it's own flags to adjust sync modes and
enabled interlaced modes which are totally irrelevant for the adjusted
mode. This worked out nicely since the input modes used by both the
load detect code and reported in the ->get_modes callbacks all have no
flags set, and we also don't fill out any of them in the ->get_config
callback.
This changed with the additional sanitation done with
commit 2960bc9cce
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Jul 30 13:36:32 2013 +0300
drm/i915: make user mode sync polarity setting explicit
sinc now the "no flags at all" state wouldn't fit through core code
any more. So fix this up again by explicitly clearing the flags in the
->compute_config callback.
Aside: We have zero checking in place to make sure that the requested
mode is indeed the right input mode we want for the selected TV mode.
So we'll happily fall over if userspace tries to pull us. But that's
definitely work for a different patch series. So just add a FIXME
comment for now.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no clear cut rules or specs for the retry interval, as there
are many factors that affect overall response time. Increase the
interval, and even more so on branch devices which may have limited i2c
bit rates.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=60263
Tested-by: Nicolas Suzor <nic@suzor.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix a bug that was introduced in commit c4c11dd160 ("drm/i2c: tda998x:
add video and audio input configuration") when Sebastian cleaned up my
original patch. Without this being fixed, audio is muted when the
display is turned off, never to be re-enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Darren Etheridge <detheridge@ti.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also changed a log message to indicate that memory was not allocated
instead of memory not available!
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing ULL when calculating the amount of vram
leads to an overflow when the amount of vram is >= 4G.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When dpm was merged, I added a new asic struct for
rv6xx, but it never got properly updated when the
hdmi callbacks were added due to the two patch sets
being developed in parallel.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69729
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
In my patch c194992cbe ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.
If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]
This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.
This patch should be backported to 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In
commit edc3d8848d
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 23 13:55:35 2013 +0300
drm/i915: avoid big kmallocs on reading error state
we introduce a two-pass mechanism for splitting long strings being
formatted into the error-state. The first pass finds the length, and the
second pass emits the right portion of the string into the accumulation
buffer. Unfortunately we use the same va_list for both passes, resulting
in the second pass reading garbage off the end of the argument list. As
the two passes are only used for boundaries between read() calls, the
corruption is only rarely seen.
This fixes the root cause behind
commit baf27f9b17
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Jun 29 23:26:50 2013 +0100
drm/i915: Break up the large vsnprintf() in print_error_buffers()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set SEL control urbs cannot be sent to a device in unconfigured state.
This patch adds a check in usb_req_set_sel() to ensure the usb device's
state is USB_STATE_CONFIGURED.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699
Signed-off-by: Florian Wolter <wolly84@web.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).
Wait until firmware ack is written before unlocking channel
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.
This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.
Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are a number of small staging tree and iio driver fixes. Nothing major,
just lots of little things.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJAdRIACgkQMUfUDdst+ymS6QCfYTqZCbIvEbdSmkbaVFkMDsoE
J4gAoKeQAL9ltn1fh65XDKlQSwLJaML3
=USmd
-----END PGP SIGNATURE-----
Merge tag 'staging-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are a number of small staging tree and iio driver fixes. Nothing
major, just lots of little things"
* tag 'staging-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
iio:buffer_cb: Add missing iio_buffer_init()
iio: Prevent race between IIO chardev opening and IIO device free
iio: fix: Keep a reference to the IIO device for open file descriptors
iio: Stop sampling when the device is removed
iio: Fix crash when scan_bytes is computed with active_scan_mask == NULL
iio: Fix mcp4725 dev-to-indio_dev conversion in suspend/resume
iio: Fix bma180 dev-to-indio_dev conversion in suspend/resume
iio: Fix tmp006 dev-to-indio_dev conversion in suspend/resume
iio: iio_device_add_event_sysfs() bugfix
staging: iio: ade7854-spi: Fix return value
staging:iio:hmc5843: Fix measurement conversion
iio: isl29018: Fix uninitialized value
staging:iio:dummy fix kfifo_buf kconfig dependency issue if kfifo modular and buffer enabled for built in dummy driver.
iio: at91: fix adc_clk overflow
staging: line6: add bounds check in snd_toneport_source_put()
Staging: comedi: Fix dependencies for drivers misclassified as PCI
staging: r8188eu: Adjust RX gain
staging: r8188eu: Fix smatch warning in core/rtw_ieee80211.
staging: r8188eu: Fix smatch error in core/rtw_mlme_ext.c
staging: r8188eu: Fix Smatch off-by-one warning in hal/rtl8188e_hal_init.c
...
Here are a number of small USB fixes for 3.12-rc2.
One is a revert of a EHCI change that isn't quite ready for 3.12. Others are
minor things, gadget fixes, Kconfig fixes, and some quirks and documentation
updates.
All have been in linux-next for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJAapIACgkQMUfUDdst+yksHQCfeYJVtsWa5aG1OgLGmVC7HzGW
SNMAniUFk9Cg9AazfBNfURsfuucEmv6w
=kf93
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 3.12-rc2.
One is a revert of a EHCI change that isn't quite ready for 3.12.
Others are minor things, gadget fixes, Kconfig fixes, and some quirks
and documentation updates.
All have been in linux-next for a bit"
* tag 'usb-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: pl2303: distinguish between original and cloned HX chips
USB: Faraday fotg210: fix email addresses
USB: fix typo in usb serial simple driver Kconfig
Revert "USB: EHCI: support running URB giveback in tasklet context"
usb: s3c-hsotg: do not disconnect gadget when receiving ErlySusp intr
usb: s3c-hsotg: fix unregistration function
usb: gadget: f_mass_storage: reset endpoint driver data when disabled
usb: host: fsl-mph-dr-of: Staticize local symbols
usb: gadget: f_eem: Staticize eem_alloc
usb: gadget: f_ecm: Staticize ecm_alloc
usb: phy: omap-usb3: Fix return value
usb: dwc3: gadget: avoid memory leak when failing to allocate all eps
usb: dwc3: remove extcon dependency
usb: gadget: add '__ref' for rndis_config_register() and cdc_config_register()
usb: dwc3: pci: add support for BayTrail
usb: gadget: cdc2: fix conversion to new interface of f_ecm
usb: gadget: fix a bug and a WARN_ON in dummy-hcd
usb: gadget: mv_u3d_core: fix violation of locking discipline in mv_u3d_ep_disable()
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
and 04bf3011 ("regulator: Support driver probe deferral") this driver
might return -EPROBE_DEFER if a gpio_request or regulator_get fails.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
this driver might return -EPROBE_DEFER if a gpio_request fails.
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Starting with UVD3 message and feedback buffers have their
own 256MB segment, so no need to force them into VRAM any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The tests are only usable if the acceleration engines have
been successfully initialized.
Based on an initial patch from: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Allow user to change the number of IOs that are reserved by
bio-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_bio_based_ios
The default value is RESERVED_BIO_BASED_IOS (16). The maximum allowed
value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_bio_based_ios() for use by DM targets and core
code. Switch to sizing dm-io's mempool and bioset using DM core's
configurable 'reserved_bio_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios
The default value is RESERVED_REQUEST_BASED_IOS (256). The maximum
allowed value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code. Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Bio-based device mapper processing doesn't need larger mempools (like
request-based DM does), so lower the number of reserved entries for
bio-based operation. 16 was already used for bio-based DM's bioset
but mistakenly wasn't used for it's _io_cache.
Formalize difference between bio-based and request-based defaults by
introducing RESERVED_BIO_BASED_IOS and RESERVED_REQUEST_BASED_IOS.
(based on older code from Mikulas Patocka)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Fix issue where the block layer would stack the discard limits of the
pool's data device even if the "ignore_discard" pool feature was
specified.
The pool and thin device(s) still had discards disabled because the
QUEUE_FLAG_DISCARD request_queue flag wasn't set. But to avoid user
confusion when "ignore_discard" is used: both the pool device and the
thin device(s) have zeroes for all discard limits.
Also, always set discard_zeroes_data_unsupported in targets because they
should never advertise the 'discard_zeroes_data' capability (even if the
pool's data device supports it).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
This is a partial revert of c6cf7777a3.
We need to take into account the clk voltage dependencies of the
board. Not doing so can lead to stability issues on certain
boards if the clks exceed the levels in the dep tables.
DPM already takes that into account, so for optimal performance,
use DPM.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds a helper function to fetch the max clock
from the voltage clock dependecy tables. Clocks above that
level tend to be unstable and will require additional driver
tweaks in order to work properly.
This patch implemented the helper function to fetch the max clocks
from the dependency tables. The following patches implement the
per-asic clock filtering.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I missed this when I fixed up this file.
Noticed-by: Mathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the linear range settings in commit 5ff26a14c3
"regulator: wm831x-ldo: Convert to use linear ranges".
For wm831x_gp_ldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xe:
volt = 0.9-1.6V in 50mV steps
sel <= 0x1f:
volt = 1.7-3.3V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
For wm831x_aldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xc:
volt = 1-1.6V in 50mV steps
sel <= 0x1f
volt = 1.7-3.5V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The some platforms (e.g., ARM) initializes their clocks as
late_initcalls for some unknown reason. So make sure
random_int_secret_init() is run after all of the late_initcalls are
run.
Cc: stable@vger.kernel.org
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
sizeof() is already size_t so there is no need to cast here. Generally,
casting inside the min() macro instead of using min_t() is considered
bad style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Have pinconf_dbg_config_write() return a ssize_t. This fixes the following
compilation warning:
drivers/pinctrl/pinconf.c:617:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/pinctrl/pinconf.c:617:2: warning: (near initialization for ‘pinconf_dbg_pinconfig_fops.write’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
- some small fixes for msm and exynos
- a regression revert affecting nouveau users with old userspace
- intel pageflip deadlock and gpu hang fixes, hsw modesetting hangs
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
Revert "drm: mark context support as a legacy subsystem"
drm/i915: Don't enable the cursor on a disable pipe
drm/i915: do not update cursor in crtc mode set
drm/exynos: fix return value check in lowlevel_buffer_allocate()
drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
drm/exynos: Fix address space warning in exynos_drm_buf.c
drm/exynos: Remove redundant OF dependency
drm/msm: drop unnecessary set_need_resched()
drm/i915: kill set_need_resched
drm/msm: fix potential NULL pointer dereference
drm/i915/dvo: set crtc timings again for panel fixed modes
drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
drm/msm: workaround for missing irq
drm/msm: return -EBUSY if bo still active
drm/msm: fix return value check in ERR_PTR()
drm/msm: fix cmdstream size check
drm/msm: hangcheck harder
drm/msm: handle read vs write fences
drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
drm/i915: Use proper print format for debug prints
...
Commit a1bc260bb5 ("gpio: clean up
gpio-ranges documentation") deprecated the #gpio-range-cells property.
Replace its usage with a hardcoded value in the gpio-rcar driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ben Hutchings says:
====================
Daniel Pieczko fixed two bugs in reset handling that particularly
affected the new SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make sure to properly initialize the IIO buffer data structure.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set the IIO device as the parent for the character device
We need to make sure that the IIO device is not freed while the character device
exists, otherwise the freeing of the IIO device might race against the file open
callback. Do this by setting the character device's parent to the IIO device,
this will cause the character device to grab a reference to the IIO device and
only release it once the character device itself has been removed.
Also move the registration of the character device before the registration of
the IIO device to avoid the (rather theoretical case) that the IIO device is
already freed again before we can add the character device and grab a reference
to the IIO device.
We also need to move the call to cdev_del() from iio_dev_release() to
iio_device_unregister() (where it should have been in the first place anyway) to
avoid a reference cycle. As iio_dev_release() is only called once all reference
are dropped, but the character device holds a reference to the IIO device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make sure that the IIO device is not freed while we still have file descriptors
for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make sure to stop sampling when the device is removed, otherwise it will
continue to sample forever.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
if device has available_scan_masks set and the buffer is enabled without
any scan_elements enabled, in a NULL pointer is dereferenced in iio_compute_scan_bytes()
[ 18.993713] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 19.002593] pgd = debd4000
[ 19.005432] [00000000] *pgd=9ebc0831, *pte=00000000, *ppte=00000000
[ 19.012329] Internal error: Oops: 17 [#1] PREEMPT ARM
[ 19.017639] Modules linked in:
[ 19.020843] CPU: 0 Not tainted (3.9.11-00036-g75c888a-dirty #207)
[ 19.027587] PC is at _find_first_bit_le+0xc/0x2c
[ 19.032440] LR is at iio_compute_scan_bytes+0x2c/0xf4
[ 19.037719] pc : [<c021dc60>] lr : [<c03198d0>] psr: 200d0013
[ 19.037719] sp : debd9ed0 ip : 00000000 fp : 000802bc
[ 19.049713] r10: 00000000 r9 : 00000000 r8 : deb67250
[ 19.055206] r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : deb67000
[ 19.062011] r3 : de96ec00 r2 : 00000000 r1 : 00000004 r0 : 00000000
[ 19.068847] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 19.076324] Control: 10c5387d Table: 9ebd4019 DAC: 00000015
problem is the rollback code in iio_update_buffers(), old_mask may be NULL (e.g. on first
call)
I'm not too confident about the fix; works for me...
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
dev_to_iio_dev() is a false friend
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8EeE
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
* tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: return EEXIST instead of EBUSY for second registering
PCI / ACPI / PM: Clear pme_poll for devices in D3cold on wakeup
ARM: shmobile: change dev_id to cpu0 while registering cpu clock
ARM: i.MX: change dev_id to cpu0 while registering cpu clock
cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device
cpufreq: cpufreq-cpu0: assign cpu_dev correctly to cpu0 device
cpufreq: unlock correct rwsem while updating policy->cpu
cpufreq: Clear policy->cpus bits in __cpufreq_remove_dev_finish()
This fixes module loading for vhost-scsi, and tweaks locking in vhost core
a bit. Both of these are not exactly release blockers but it's early
in the cycle so I think it's a good idea to apply them now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSOWVbAAoJECgfDbjSjVRp10UIALB3nkEdmhC011ld+7xgVxMt
hB5gN1Uw3nhZOxOd1t+udHERSuZWw2CjkGRetpLHPh22bMHpHIb++Y0FvNGG9kIY
RRSrBuFupPTCpLlsI8bkCx1uqO8VpZiKwEh1h9SxmqWmuGIJgno1ZnVhMx+fTwmn
Av4ERtc3LrzR4RgaZqYLBf/6Ed+ElZzwi6xNvwV6rrN9oKZR2pRJSSvkJkDQzwN7
lRdHZJrtwd5KyMoUdPmSoafwCZnrjGIwYQpXq3jpvePAYF1Ot6p/+r/M1BaEHR7N
eUfMp4ItCXZubrUeiXuqlX/dPCq+DtQePoO86OyviVS7URlHEpAkOu2hPpi8m5M=
=I209
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost updates from Michael Tsirkin:
"vhost: minor changes on top of 3.12-rc1
This fixes module loading for vhost-scsi, and tweaks locking in vhost
core a bit. Both of these are not exactly release blockers but it's
early in the cycle so I think it's a good idea to apply them now"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-scsi: whitespace tweak
vhost/scsi: use vmalloc for order-10 allocation
vhost: wake up worker outside spin_lock
Prevent NULL pointer dereference in case when radeon_ring_fini() did it's job.
Reading of r100_cp_ring_info and radeon_ring_gfx debugfs entries will lead to a KP if ring buffer was deallocated, e.g. on failed ring test.
Seen on PA-RISC machine having "radeon: ring test failed (scratch(0x8504)=0xCAFEDEAD)" issue.
v2: agd5f: add some parens around ring->ready check
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There are multiple valid values, not just 0 or 1. Required
to properly support 2D tiling in the userspace drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The old implementation was heavy on str* functions and sprintf calls.
This version is more manual, but faster.
Profiling just the printing of a 3 char CAN-id resulted in 60 instructions
for the manual method and over 2000 for the sprintf method. Bear in
mind the profiling was done against libc and not the kernel sprintf.
Together with this rewrite an issue with sending and receiving of RTR frames
has been fixed by Oliver for the cases that the DLC is not zero.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locking is needed, since the the internal buffer for the CAN frames is
changed during the wakeup call. This could cause buffer inconsistencies
under high loads, especially for the outgoing short CAN packet skbuffs.
The needed locks led to deadlocks before commit
"5ede52538ee2b2202d9dff5b06c33bfde421e6e4 tty: Remove extra wakeup from pty
write() path", which removed the direct callback to the wakeup function from the
tty layer.
As slcan.c is based on slip.c the issue in the original code is fixed, too.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx and rx urbs are not deallocated if something goes wrong in peak_usb_start().
The patch fixes error handling to deallocate all the resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The string is encoded from the MSB to the LSB of the register.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the user has forced the driver to use the internal GPU gart
rather than AGP on an AGP card, force the buffers to vram
as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Cc: stable@vger.kernel.org
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSO8JQAAoJEAi3KVZQDZAe660IAJV2Zqc/iMxmRJLCPoFnSpGd
uFsthQx0e+OGVW+KowykPve2p6RxOqol2wR1IvgMlkCPFBtUGhGkEeXvJ1wenS9H
JNEtG7fU6AAiaw9dfS6OJtPMxQK3yTSjkVcuaNi0Ds/q99ja9ZYR6RPYzqe8kQME
k9dX3OGNzm+nI7BKheVYcB4zmxBfCtSHzBe2tdwK6mdoki9Qdt4FY4LosXwQHt4d
5BjHGLLgbOp/fCrztgYD4ZiuuJekXz51OP1ut2giIdlakgW0DIRCRadyLyyZMH7S
Wrl636TaYAdh/jXu00mTZIj13K0NDXcERjemjb7O16LFB0fAIz+DYXVVM2nB1iE=
=B2UP
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper, mvebu fixes for v3.12:
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
* tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu:
ARM: kirkwood: Fix address of second XOR engine
ARM: mvebu: Add clock properties to Armada XP timer node
ARM: mvebu: Add the reference 25 MHz fixed-clock to Armada XP
ARM: Kirkwood: Add missing DT reg property to cpu@0
bus: mvebu: add missing of_node_put() to fix reference leak
ARM: mvebu: add missing of_node_put() to fix reference leak
Signed-off-by: Olof Johansson <olof@lixom.net>
The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Scheduling a reset following an MC reboot event before waiting for
reboot to complete results in a race that can lead to a state where
must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have
been destroyed during the MC reboot.
To avoid MC errors when trying to remove VIs that do not exist, wait
for the MC reboot to complete before scheduling the reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Workaround the SCSI layer's problematic WRITE SAME heuristics by
disabling WRITE SAME in the DM multipath device's queue_limits if an
underlying device disabled it.
The WRITE SAME heuristics, with both the original commit 5db44863b6
("[SCSI] sd: Implement support for WRITE SAME") and the updated commit
66c28f971 ("[SCSI] sd: Update WRITE SAME heuristics"), default to enabling
WRITE SAME(10) even without successfully determining it is supported.
After the first failed WRITE SAME the SCSI layer will disable WRITE SAME
for the device (by setting sdkp->device->no_write_same which results in
'max_write_same_sectors' in device's queue_limits to be set to 0).
When a device is stacked ontop of such a SCSI device any changes to that
SCSI device's queue_limits do not automatically propagate up the stack.
As such, a DM multipath device will not have its WRITE SAME support
disabled. This causes the block layer to continue to issue WRITE SAME
requests to the mpath device which causes paths to fail and (if mpath IO
isn't configured to queue when no paths are available) it will result in
actual IO errors to the upper layers.
This fix doesn't help configurations that have additional devices
stacked ontop of the mpath device (e.g. LVM created linear DM devices
ontop). A proper fix that restacks all the queue_limits from the bottom
of the device stack up will need to be explored if SCSI will continue to
use this model of optimistically allowing op codes and then disabling
them after they fail for the first time.
Before this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: failing WRITE SAME IO with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
device-mapper: multipath: Failing path 8:112.
end_request: I/O error, dev dm-6, sector 4616
dm-6: WRITE SAME failed. Manually zeroing.
end_request: I/O error, dev dm-6, sector 4616
end_request: I/O error, dev dm-6, sector 5640
end_request: I/O error, dev dm-6, sector 6664
end_request: I/O error, dev dm-6, sector 7688
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
end_request: I/O error, dev dm-6, sector 524296
Aborting journal on device dm-6-8.
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
33553920
After this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: WRITE SAME I/O failed with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
0
It should be noted that WRITE SAME support wasn't enabled in DM
multipath until v3.10.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
LVM2, since version 2.02.96, creates origin with zero size, then loads
the snapshot driver and then loads the origin. Consequently, the
snapshot driver sees the origin size zero and sets the hash size to the
lower bound 64. Such small hash table causes performance degradation.
This patch changes it so that the hash size is determined by the size of
snapshot volume, not minimum of origin and snapshot size. It doesn't
make sense to set the snapshot size significantly larger than the origin
size, so we do not need to take origin size into account when
calculating the hash size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The kernel reports a lockdep warning if a snapshot is invalidated because
it runs out of space.
The lockdep warning was triggered by commit 0976dfc1d0
("workqueue: Catch more locking problems with flush_work()") in v3.5.
The warning is false positive. The real cause for the warning is that
the lockdep engine treats different instances of md->lock as a single
lock.
This patch is a workaround - we use flush_workqueue instead of flush_work.
This code path is not performance sensitive (it is called only on
initialization or invalidation), thus it doesn't matter that we flush the
whole workqueue.
The real fix for the problem would be to teach the lockdep engine to treat
different instances of md->lock as separate locks.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.5+
* pm-cpufreq:
cpufreq: return EEXIST instead of EBUSY for second registering
ARM: shmobile: change dev_id to cpu0 while registering cpu clock
ARM: i.MX: change dev_id to cpu0 while registering cpu clock
cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device
cpufreq: cpufreq-cpu0: assign cpu_dev correctly to cpu0 device
cpufreq: unlock correct rwsem while updating policy->cpu
cpufreq: Clear policy->cpus bits in __cpufreq_remove_dev_finish()
A set of fixes for ARM platforms for 3.12. Among them:
- A fix for build breakage in the MTD subsystem for some PXA devices.
David Woodhouse has this patch in his for-next branch but has not been
responding to our requests to send it up so here it is.
I should have amended the commit message to describe the build failure for
CONFIG_OF=n setups, but forgot and now it's down in the stack of commits.
- Added device-tree for the BeagleBone Black. Turns out people have been
using the older "regualar" bone DT for the newer boards, and there's
risk of damaging hardware that way.
- Misc DT and regular fixes for OMAP.
- Fix to make the ST-Ericsson "snowball" boards boot with
multi_v7_defconfig, and enable one of the ST-E reference boards on the
same config.
- Kconfig cleanup for u300 to hide submenus when the platform isn't
enabled.
- Enable ARM_ATAG_DTB_COMPAT to let firmware override command
line when booting with an appended devicetree on non-DT-enabled
firmware (needed to boot snowball).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I14p
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes for ARM platforms for 3.12. Among them:
- A fix for build breakage in the MTD subsystem for some PXA devices.
David Woodhouse has this patch in his for-next branch but has not
been responding to our requests to send it up so here it is. I
should have amended the commit message to describe the build
failure for CONFIG_OF=n setups, but forgot and now it's down in the
stack of commits.
- Added device-tree for the BeagleBone Black. Turns out people have
been using the older "regualar" bone DT for the newer boards, and
there's risk of damaging hardware that way.
- Misc DT and regular fixes for OMAP.
- Fix to make the ST-Ericsson "snowball" boards boot with
multi_v7_defconfig, and enable one of the ST-E reference boards on
the same config.
- Kconfig cleanup for u300 to hide submenus when the platform isn't
enabled.
- Enable ARM_ATAG_DTB_COMPAT to let firmware override command line
when booting with an appended devicetree on non-DT-enabled firmware
(needed to boot snowball)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: multi_v7: add HREFv60 to multi_v7 defconfig
ARM: OMAP2+: mux: fix trivial typo in name
ARM: OMAP4 SMP: Corrected a typo fucntions to functions
ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionally
mailbox: remove unnecessary platform_set_drvdata()
ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=y
ARM: OMAP: fix return value check in omap_device_build_from_dt()
ARM: OMAP4: Fix clock_get error for GPMC during boot
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
ARM: u300: hide submenus
ARM: dts: igep00x0: Add pinmux configuration for MCBSP2
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard
mtd: nand: pxa3xx: Remove unneeded ifdef CONFIG_OF
ARM: multi_v7_defconfig: enable ARM_ATAG_DTB_COMPAT
ARM: ux500: disable outer cache debug
ARM: dts: OMAP5: fix ocp2scp DTS data
ARM: dts: OMAP5: fix reg property size
ARM: dts: am335x-bone*: add DT for BeagleBone Black
ARM: dts: omap3-beagle-xm: fix string error in compatible property
...
A couple small msm fixes. Plus drop of set_need_resched().
* 'msm-fixes-3.12' of git://people.freedesktop.org/~robclark/linux:
drm/msm: drop unnecessary set_need_resched()
drm/msm: fix potential NULL pointer dereference
drm/msm: workaround for missing irq
drm/msm: return -EBUSY if bo still active
drm/msm: fix return value check in ERR_PTR()
drm/msm: fix cmdstream size check
drm/msm: hangcheck harder
drm/msm: handle read vs write fences
Just small fixes, and code cleanups.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: fix return value check in lowlevel_buffer_allocate()
drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
drm/exynos: Fix address space warning in exynos_drm_buf.c
drm/exynos: Remove redundant OF dependency
Some more dealock fixes around pageflips and gpu hangs, fixes for hsw hangs
when doing modesets/dpms. And a few minor things to rectify issues with our
modeset state tracking which the checker spotted.
* tag 'drm-intel-fixes-2013-09-19' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Don't enable the cursor on a disable pipe
drm/i915: do not update cursor in crtc mode set
drm/i915: kill set_need_resched
drm/i915/dvo: set crtc timings again for panel fixed modes
drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
drm/i915: Use proper print format for debug prints
drm/i915: fix wait_for_pending_flips vs gpu hang deadlock
drm/i915: Track pfit enable state separately from size
On systems that support intel_pstate, acpi_cpufreq fails to load, and
udev keeps trying until trace gets filled up and kernel crashes.
The root cause is driver return ret from cpufreq_register_driver(),
because when some other driver takes over before, it will return
EBUSY and then udev will keep trying ...
cpufreq_register_driver() should return EEXIST instead so that the
system can boot without appending intel_pstate=disable and still use
intel_pstate.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 7c510133d9.
Well looks like not enough digging was done, libdrm_nouveau before 2.4.33
used contexts,
292da616fe1f936ca78a3fa8e1b1b19883e343b6 nouveau: pull in major libdrm rewrite
got rid of them,
Reported-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 448bd85 (PCI/PM: add PCIe runtime D3cold support) added a
piece of code to pci_acpi_wake_dev() causing that function to behave
in a special way for devices in D3cold (so that their configuration
registers are not accessed before those devices are resumed).
However, it didn't take the clearing of the pme_poll flag into
account. That has to be done for all devices, even if they are in
D3cold, or pci_pme_list_scan() will not know that wakeup has been
signaled for the device and will poll its PME Status bit
unnecessarily.
Fix the problem by moving the clearing of the pme_poll flag in
pci_acpi_wake_dev() before the code introduced by commit 448bd85.
Reported-and-tested-by: David E. Box <david.e.box@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.6+ <stable@vger.kernel.org> # 3.6+
Pull networking fixes from David Miller:
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
This bug was introduced by commit
7a163bfb7c ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 136d8f377e broke the skge driver.
Note this part of the patch:
+ if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(nskb);
+ goto resubmit;
+ }
+
pci_unmap_single(skge->hw->pdev,
dma_unmap_addr(e, mapaddr),
dma_unmap_len(e, maplen),
PCI_DMA_FROMDEVICE);
skb = e->skb;
prefetch(skb->data);
- skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.
This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.
For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.
With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
- Minor updates and fixes to the Octeon ethernet driver in staging
- A fix to VGA_MAP_MEM() for 64 bit platforms
- Fix a workaround for 74K/1074K processors
- The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a
a file with a name ending in \n. I think this may have been caused
by a git bug with with patches sent by email
- A build fix for VGA console on BCM1480-based systems
- Fix PCI device access via "/sys/bus/pci/.../resource0" or similar
work for Alchemy platforms
- Fix potential data leak on MIPS R5 cores. This doesn't add proper
support for any R5 features, just ensures a kernel without such
support will be secure to run
- Adding a macros for the CP0 Config5 register to be used by the R5 fix
- Make get_cycles() actually return something useful where possible
This also requires a preparatory patch for performance sake
- Fix a warning about the use of smp_processor_id() in preemptible
code. Again this includes a preparatory patch adding the
infrastructure to be used by the actual patch
- Finally remove pointless one-line comment
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix invalid symbolic link file
MIPS: PCI: pci-bcm1480: Include missing vt.h header
MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
MIPS: Add MIPS R5 config5 register.
MIPS: PCI: Use pci_resource_to_user to map pci memory space properly
MIPS: 74K/1074K: Correct erratum workaround.
MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
MIPS: Remove useless comment about kprobe from arch/mips/Makefile
MIPS: Fix VGA_MAP_MEM macro.
MIPS: Reimplement get_cycles().
MIPS: Optimize current_cpu_type() for better code.
MIPS: Fix accessing to per-cpu data when flushing the cache
MIPS: Provide nice way to access boot CPU's data.
staging: octeon-ethernet: rgmii: enable interrupts that we can handle
staging: octeon-ethernet: remove skb alloc failure warnings
staging: octeon-ethernet: make dropped packets to consume NAPI budget
Pull ceph fixes from Sage Weil:
"These fix several bugs with RBD from 3.11 that didn't get tested in
time for the merge window: some error handling, a use-after-free, and
a sequencing issue when unmapping and image races with a notify
operation.
There is also a patch fixing a problem with the new ceph + fscache
code that just went in"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
fscache: check consistency does not decrement refcount
rbd: fix error handling from rbd_snap_name()
rbd: ignore unmapped snapshots that no longer exist
rbd: fix use-after free of rbd_dev->disk
rbd: make rbd_obj_notify_ack() synchronous
rbd: complete notifies before cleaning up osd_client and rbd_dev
libceph: add function to ensure notifies are complete
As per datasheet, voltage range for LDOs are as follows:
0000 = 0.9V
...(50mV steps)
01111 = 1.65V
10000 = 1.8V
... (100mV stepns)
11111 = 3.3V
So, there is no selector for 1.65V to 1.8V.
Correcting the range for max_uV for selector between 0 to 15.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver cannot be built as a module, so having a MODULE_ALIAS() isn't
useful.
While at it, fix a small typo in the file header comment and make the
module description string consistent with those for earlier Tegra SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have a bug with omapdrm, where omapdrm calls dispc's pm_runtime
function in atomic context, and dispc's pm_runtime is not marked as
irq_safe:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:952
Dispc's runtime PM callbacks are irq safe, so we can just set the
irq_safe flag to fix the issue.
However, in the long term, I'd rather have omapdrm manage the runtime PM
calls in a better way. Calling get/put for every small operation that
touches the dispc registers is very inefficient. It'd be better and
cleaner to have clear "in-use" and "not-in-use" states for dispc, so
that we don't need to do register context restore for small operations,
only to turn dispc off right afterwards.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While using HDMI connector driver with sil9022 encoder
came across issue where connector driver is probed first.
This resulted in error. A deffered probe solved this.
Most connector drivers need a encoder driver as their
video source. This patch ensures we do a probe defferal
if video source is not present for connector drivers.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull drm radeon/nouveau/core fixes from Dave Airlie:
"Mostly radeon fixes, with some nouveau bios parser, ttm fix and a fix
for AST driver"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
drm/fb-helper: don't sleep for screen unblank when an oops is in progress
drm, ttm Fix uninitialized warning
drm/ttm: fix the tt_populated check in ttm_tt_destroy()
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
drm/radeon: avoid UVD corruptions on AGP cards
drm/radeon: fix panel scaling with eDP and LVDS bridges
drm/radeon/dpm: rework auto performance level enable
drm/radeon: Fix hmdi typo
drm/radeon/dpm/rs780: fix force_performance state for same sclks
drm/radeon/dpm/rs780: don't enable sclk scaling if not required
drm/radeon/dpm/rs780: add some sanity checking to sclk scaling
drm/radeon/dpm/rs780: use drm_mode_vrefresh()
drm/udl: rip out set_need_resched
drm/ast: fix the ast open key function
drm/radeon/dpm: add bapm callback for kb/kv
drm/radeon/dpm: add bapm callback for trinity
drm/radeon/dpm: add infrastructure to properly handle bapm
...
Otherwise the system will burn even brighter and worse, leave the user
wondering what's going on exactly.
Since we already have a panic handler which will (try) to restore the
entire fbdev console mode, we can just bail out. Inspired by a patch from
Konstantin Khlebnikov. The callchain leading to this, cut&pasted from
Konstantin's original patch:
callstack:
panic()
bust_spinlocks(1)
unblank_screen()
vc->vc_sw->con_blank()
fbcon_blank()
fb_blank()
info->fbops->fb_blank()
drm_fb_helper_blank()
drm_fb_helper_dpms()
drm_modeset_lock_all()
mutex_lock(&dev->mode_config.mutex)
Note that the entire locking in the fb helper around panic/sysrq and kdbg
is ... non-existant. So we have a decent change of blowing up
everything. But since reworking this ties in with funny concepts like the
fbdev notifier chain or the impressive things which happen around
console_lock while oopsing, I'll leave that as an exercise for braver
souls than me.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit cdc58d602d "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.
This patch fixes the wrong assignment to cpu_dev.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit f837a9b5ab "cpufreq: cpufreq-cpu0:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.
This patch fixes the wrong assignment to cpu_dev.
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix uninitialized warning.
drivers/gpu/drm/ttm/ttm_object.c: In function ‘ttm_base_object_lookup’:
drivers/gpu/drm/ttm/ttm_object.c:213:10: error: ‘base’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
kref_put(&base->refcount, ttm_release_base);
^
drivers/gpu/drm/ttm/ttm_object.c:221:26: note: ‘base’ was declared here
struct ttm_base_object *base;
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After a vmalloc failure in ttm_dma_tt_alloc_page_directory(),
ttm_dma_tt_init() will call ttm_tt_destroy() to cleanup, and end up
inside the driver's unpopulate() hook when populate() has never yet
been called.
On nouveau, the first issue to be hit because of this is that
dma_address[] may be a NULL pointer. After working around this,
ttm_pool_unpopulate() may potentially hit the same issue with
the pages[] array.
It seems to make more sense to avoid calling unpopulate on already
unpopulated TTMs than to add checks to all the implementations.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@vger.kernel.org
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A couple of bios parser fixes (one for ancient chips, another for new ones - important in Optimus configs). Another to make sure KMS is enabled on certain Optimus configs, and a TTM failure path fix.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
a few trivial typo fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=HQjo
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren, fixes for 3.12-rc1:
OMAP fixes for build warnings and cpuidle, and a few trivial typo fixes.
* tag 'omap-for-v3.12/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: mux: fix trivial typo in name
ARM: OMAP4 SMP: Corrected a typo fucntions to functions
ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionally
mailbox: remove unnecessary platform_set_drvdata()
ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=y
ARM: OMAP: fix return value check in omap_device_build_from_dt()
ARM: OMAP4: Fix clock_get error for GPMC during boot
Signed-off-by: Olof Johansson <olof@lixom.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ade7854_probe can fail. Return the value obtained from it
instead of 0 (success).
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Barry Song <21cnbao@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
recently broken, cd6fe06588
staging:iio:hmc5843: Use i2c_smbus_read_word_swapped()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The lux_uscale value is not initialized at probe. The value will be
uninitialized unless a value is written to it through the iio channel interface.
This fixes that.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65998
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This only occurs in the unlikely event that the example driver is built
in whilst the buffer implementation is not.
Solved by switching from a depends on to a select for this particular case.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The adc_clk variable is currently defined using a 32-bits unsigned integer,
which will overflow under some very valid range of operations.
Such overflow will occur if, for example, the parent clock is set to a
20MHz frequency and the ADC startup time is larger than 215ns.
To fix this, introduce an intermediate variable holding the clock rate
in kHz.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There was a deliberate race condition in dm_stat_for_entry() to avoid the
overhead of disabling and enabling interrupts. The race could result in
some events not being counted on 64-bit architectures.
However, on 32-bit architectures, operations on long long variables are
not atomic, so the race condition could cause the counter to jump by 2^32.
Such jumps could be disruptive, so we need to do proper locking on 32-bit
architectures.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Alasdair G. Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Since ENOSPC is a target-side error, dm-mpath should just pass the error
information to upper layer instead of retrying itself with path failover.
Otherwise it will end up failing all paths down while path checkers find
all paths ok.
ENOSPC can now be returned from SCSI device after commit a9d6ceb8
("[SCSI] return ENOSPC on thin provisioning failure").
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add of_node_put to properly decrement the refcount when we are
done using a given node.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
drivers/bus/mvebu-mbus.c
commit 104a43edb2
cnic: Use CHIP_NUM macros from bnx2x.h
changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not. There is another place in cnic that is still using
the old method to determine if FCoE is supported or not. The 2 methods
may not yield the same result after the network interface is brought down
and up. This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.
The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro. As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b9871bcfd2
bnx2x: VF RSS support - PF side
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Move the crtc active checks to intel_crtc_cursor_{set,move} to
avoid confusing people during modeset
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor is disabled before crtc mode set in crtc disable (and we
assert this is the case), and enabled afterwards in crtc enable. Do not
update it in crtc mode set.
On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Add note about HSW hangs - vsyrjala
Cc: stable@vger.kernel.org
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from v3.10 (probably commit f91e2590410b: "tty: Signal
foreground group processes in hangup") disassociate_ctty() sends SIGCONT
if tty && on_exit. This breaks LSB test-suite, in particular test8 in
_exit.c and test40 in sigcon5.c.
Put the "!on_exit" check back to restore the old behaviour.
Review by Peter Hurley:
"Yes, this regression was introduced by me in that commit. The effect
of the regression is that ptys will receive a SIGCONT when, in similar
circumstances, ttys would not.
The fact that two test vectors accidentally tripped over this
regression suggests that some other apps may as well.
Thanks for catching this"
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Karel Srot <ksrot@redhat.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit afbd8bae9c
vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
ip link add vxlan1 type vxlan id 100
creates the following fdb entry
00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent
This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.
Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code looks like this:
WARN_ON(lock_policy_rwsem_write(cpu));
update_policy_cpu(policy, new_cpu);
unlock_policy_rwsem_write(cpu);
{lock|unlock}_policy_rwsem_write(cpu) takes/releases policy->cpu's rwsem.
Because cpu is changing with the call to update_policy_cpu(), the
unlock_policy_rwsem_write() will release the incorrect lock.
The right solution would be to release the same lock as was taken earlier. Also
update_policy_cpu() was also called from cpufreq_add_dev() without any locks and
so its better if we move this locking to inside update_policy_cpu().
This patch fixes a regression introduced in 3.12 by commit f9ba680d23
(cpufreq: Extract the handover of policy cpu to a helper function).
Reported-and-tested-by: Jon Medhurst<tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This broke after a recent change "cedb70a cpufreq: Split __cpufreq_remove_dev()
into two parts" from Srivatsa.
Consider a scenario where we have two CPUs in a policy (0 & 1) and we are
removing CPU 1. On the call to __cpufreq_remove_dev_prepare() we have cleared 1
from policy->cpus and now on a call to __cpufreq_remove_dev_finish() we read
cpumask_weight of policy->cpus, which will come as 1 and this code will behave
as if we are removing the last CPU from policy :)
Fix it by clearing the CPU mask in __cpufreq_remove_dev_finish() instead of
__cpufreq_remove_dev_prepare().
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=51X+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.12-rc2
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
As vhost scsi device struct is large, if the device is
created on a busy system, kzalloc() might fail, so this patch does a
fallback to vzalloc().
As vmalloc() adds overhead on data-path, add __GFP_REPEAT
to kzalloc() flags to do this fallback only when really needed.
Reviewed-by: Asias He <asias@redhat.com>
Reported-by: Dan Aloni <alonid@stratoscale.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Right after the musb_hdrc driver is loaded, the otg default state
is a_idle, and Mode=Host, which are set by musb_host_setup().
This causes the following kernel message during musb gadget
enumeration.
CAUTION: musb: Babble Interrupt Occurred
This patch sets the otg default state to b_idle, and its Mode to
Peripheral.
It has been validated on TI AM335x GP EVM USB0 port with g_zero.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 40d5e0905a,
'n_tty: Fix EOF push handling' introduced a subtle state
change error wrt EOF push handling when the termios is
changed from non-canonical to canonical mode.
Reset line_start to the current read_tail index, not 0.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused tty-reference from dma-rx path which was left after the
recent tty-port conversions.
Also remove a redundant port initialisation while at it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tty_kref leak when tty_buffer_request room fails in dma-rx path.
Note that the tty ref isn't really needed anymore, but as the leak has
always been there, fixing it before removing should makes it easier to
backport the fix.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tty-kref leak introduced by commit 384e301e ("pch_uart: fix a
deadlock when pch_uart as console") which never put its tty reference.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Prolific, several (unauthorized) cheap and less functional
clones of the PL2303HX chip are in circulation. [1]
I've had the chance to test such a cloned device and it turned out that
it doesn't support any baud rates above 115200 baud (original: 6 Mbaud)
It also doesn't support the divisior based baud rate encoding method,
so no continuous baud rate adjustment is possible.
Nevertheless, these devices have been working (unintentionally) with
the driver up to commit 61fa8d694b ("pl2303: also use the divisor based
baud rate encoding method for baud rates < 115200 with HX chips"), and
this commit broke support for them.
Fortunately, it is pretty simple to distinguish between the original
and the cloned HX chips, so I've added a check and an extra chip type
to keep the clones working.
The same check is used by the latest Prolific Windows driver, so it
should be solid.
[1] http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the MODULE_AUTHOR field of the Faraday OTG drivers to reflect
current maintainers email address.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ajit Khaparde
David S. Miller
John W. Linville
Linus Torvalds
Chew, Chiau Ee
Thierry Reding
Kim Phillips
Laxman Dewangan
Nishanth Menon
Mateusz Krawczuk
Mark Brown
Jesse Brandeburg
Todd Fujinaka
Elie De Brauwer
Brian Norris
Wei Yongjun
Rafael J. Wysocki
Larry Finger
David Cohen
Shengzhou Liu
Al Viro
Benson Leung
K. Y. Srinivasan
Alexander Usyskin
Tomas Winkler
Roger Luethi
Ramneek Mehresh
Arend van Spriel
Bing Zhao
Amitkumar Karwar
Christian Lamparter
Solomon Peachy
Felix Fietkau
Alexey Khoroshilov
Sujith Manoharan
Marek Vasut
Henrik Rydberg
Andrzej Hajda
David Herrmann
Uwe Kleine-König
Peter Hurley
Magnus Damm
Kurt Garloff
Geert Uytterhoeven
Peter Chen
Sebastian Hesselbarth
Tomasz Figa
Jean Pihet
Alan Stern
Fabio Estevam
Malcolm Priestley
Iker Pedrosa
Thomas Meyer
Daniel Vetter
Bin Liu
Mikael Pettersson
Hanjun Guo
Alex Deucher
Sachin Kamat
Viresh Kumar
Yinghai Lu
Lv Zheng
Dan Carpenter
Kent Overstreet
Gabriel de Perthuis
David Vrabel
Jason Gunthorpe
Jani Nikula
Russell King
malahal@us.ibm.com
Mikulas Patocka
Joerg Roedel
Chris Wilson
Xenia Ragiadakou
Florian Wolter
Sarah Sharp
Mathias Nyman
Ken O'Brien
Ariel Elior
Yuval Mintz
Eilon Greenstein
Johan Hovold
Christian König
Mike Snitzer
Axel Lin
Theodore Ts'o
Vincent Stehlé
Yaniv Rosner
Laurent Pinchart
Guennadi Liakhovetski
Lars-Peter Clausen
Peter Meerwald
Alex Ivanov
Michel Dänzer
Andre Naujoks
Olof Johansson
Daniel Pieczko
Dave Airlie
Nikolay Aleksandrov
Ansis Atteka
Paul Durrant
Tomi Valkeinen
Sathya Prakash M R
Sudeep KarkadaNagesha
Prarit Bhargava
Ben Skeggs
Jingoo Han
Lukasz Czerwinski
Derek Basehore
Jonathan Cameron
Josh Wu
Jun'ichi Nomura
Jisheng Zhang
Michael Chan
Ville Syrjälä
Oleg Nesterov
Sridhar Samudrala
Avinash Kumar
Eric W. Biederman
Greg Kroah-Hartman
Michael S. Tsirkin
Frank Schäfer
Dave Jones