There is no need to disable/enable PLLA when switching to one of the
ULP modes. The PLLA consumers should take care of this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add ULP1 support for SAM9X60. In pm_suspend.S enable RC oscillator in
PMC if it is not enabled. At resume the state before suspend is
restored.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The SAMA5D2 NRST input signal is resynchronized with the SLCK clock and it
can take up to 2 SLCK cycles (about 90us) for the internal reset to be
effective. During this delay, the VDDCORE current consumption may still be
high (application-dependent) with the VDDCORE regulator already OFF. Under
such conditions, VDDCORE may operate below its operating range leading to
potential register corruption.
To prevent such situation, it is recommended to decrease significantly the
power consumption of the device once the voltage regulator is turned-off.
This can be achieved by operating the device at a much lower low frequency.
To solve this switch the master clock to slock clock just before writing
shutdown command to shutdown controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Suggested-by: Patrice Vilchez <patrice.vilchez@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the ULP1 mode, in order to achieve the lowest power consumption
with the system in retention mode and be able to resume on the wake
up events, all the clocks are shut off, inclusive the embedded 12MHz
RC oscillator, and the number of wake up sources is limited as well.
When the wake up event is asserted, the embedded 12MHz RC oscillator
restarts automatically.
The ULP1 (Ultra Low-power mode 1) is introduced by SAMA5D2.
The previous size of pm_suspend.o was 2148 bytes. With the addition of
ULP1 mode the new size of pm_suspend.o raised at 2456 bytes.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[claudiu.beznea@microchip.com: aligned with 4.18-rc1]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch to use ULP0 naming instead of slow clock naming for power modes, to
be as closed as possible to datasheet. This commit does the necessary
renaming and macro addition to be as close as possible to the namings
from [1].
[1] https://lore.kernel.org/lkml/1470650705-31418-3-git-send-email-wenyou.yang@atmel.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The sama5d2 has a mode were it is possible to cut power to the SoC while
keeping the RAM in self refresh.
Resuming from that mode needs support in the firmware/bootloader.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Add a missing bracket at the end of Anti's email
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The number of register we can safely pass to at91_pm_suspend_in_sram is
limited. Instead, pass the address to the at91_pm_data structure.
The offsets are automatically generated to avoid hardcoding them.
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
fncpy() requires that the source and the destination are both 8-byte
aligned.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: d94e688cae ("ARM: at91/pm: move the copying the sram function to the sram initialization phase")
Cc: <stable@vger.kernel.org> # 4.1+
Use the defines from atmel-mc.h instead of at91rm9200_sdramc.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
hardware.h is now mostyl unused, move the remaining declarations to pm.c and
remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the WFI instruction to make the cpu to the idle state.
In the meanwhile, disable the processor's clock.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the file name is renamed, rename the function name at91_slow_clock()
--> at91_pm_suspend_sram_fn(), rename the function handler's name at the
same time.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: little update of the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Because the sram function is used for both suspend to memory and the suspend
to standby mode, renaming is more elegant.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Claudiu Beznea
Wenyou Yang
Alexandre Belloni
Patrick Doyle