This driver doesn't appear to support vlan acceleration at
all. However, it does claim to support TSO and IP checksums
for vlan devices. Thus any configured vlan device would
end up passing down partial checksums or TSO frames.
The driver also uses the value from skb->protocol to
determine TSO and checksum offload information, but assumes
that skb->protocol holds the l3 protocol information.
As a result, vlan traffic with partial checksums or TSO
will fail those checks and TSO will not happen.
Fix this by using vlan_get_protocol() helper.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver claims that it can do TSO and IP checksums on vlan
devices and also allows user to control vlan acceleration offloading.
This makes it possible to push traffic to this driver that has TSO or
partial checksums set, but also have a non-accelearted vlan
header. In this case, the driver will fail to correctly
identify such traffic and will not correctly perform
segmentation and checksum calculation.
Fix this by using vlan_get_protocol() helper instead of
assuming skb->protocol always has this information.
CC: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information. This results
in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
CC: Rasesh Mody <rmody@brocade.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This will results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO support for vlans. It also allows a
user to control vlan acceleration offloading. As such, it is
possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information. This results
in corrupted frames sent on the wire. Corruptions include
incorrect IP total length and invalid IP checksum.
This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netdev_alloc_skb_ip_align() fails, subsequent code will
try to dereference an invalid pointer.
Continue to next descriptor on error.
While we're at it,
1. eliminate the chance of an endless loop, replace the main
loop with while(rx < budget)
2. use napi_complete() and remove the explicit napi_gro_flush()
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA memory should be synchronized before data is passed
to/from controller.
Add dma_sync_single_for_cpu(.., DMA_FROM_DEVICE) to RX path
and dma_sync_single_for_device(.., DMA_TO_DEVICE) to TX path.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() is used to make skbs out of existing RX ring memory
which is bad because the RX ring is allocated only once, on probe.
Memory corruption occur because said memory is reclaimed, i.e.
__kfree_skb() (and eventually put_page()).
Replace build_skb() with netdev_alloc_skb_ip_align() and use memcpy().
Remove SKB_DATA_ALIGN() from RX buffer size while we're at it.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69041
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX buffer length is not cleared on ndo_start_xmit().
Failing to do so can bug/hang the controller and
cause TX interrupts to stop altogether.
Remove the readl() and compute a new value for DESC1.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69031
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is follow-up to
da08143b85 ("vlan: more careful checksum features handling")
which introduced more careful feature intersection in vlan code,
taking into account that HW_CSUM should be considered superset
of IP_CSUM/IPV6_CSUM. The same is needed in netif_skb_features()
in order to avoid offloading mismatch warning when vlan is
created on top of a bond consisting of slaves supporting IP/IPv6
checksumming but not vlan Tx offloading.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Epoll on trace_pipe can sometimes hang in a weird case. If the ring buffer is
empty when we set waiters_pending but an event shows up exactly at that moment
we can miss being woken up by the ring buffers irq work. Since
ring_buffer_empty() is inherently racey we will sometimes think that the buffer
is not empty. So we don't get woken up and we don't think there are any events
even though there were some ready when we added the watch, which makes us hang.
This patch fixes this by making sure that we are actually on the wait list
before we set waiters_pending, and add a memory barrier to make sure
ring_buffer_empty() is going to be correct.
Link: http://lkml.kernel.org/p/1408989581-23727-1-git-send-email-jbacik@fb.com
Cc: stable@vger.kernel.org # 3.10+
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Enable more identifiers for the existing devices for Intel Braswell and
Cherryview.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is platform refusing to respond QR_EC when SCI_EVT isn't set
which is Acer Aspire V5-573G.
By disallowing QR_EC to be issued before the previous one has been
completed we are able to reduce the possibilities to trigger issues on
such platforms.
Note that this fix can only reduce the occurrence rate of this issue, but
this issue may still occur when such a platform doesn't clear SCI_EVT
before or immediately after completing the previous QR_EC transaction.
This patch cannot fix the CLEAR_ON_RESUME quirk which also relies on
the assumption that the platforms are able to respond even when SCI_EVT
isn't set.
But this patch is still useful as it can help to reduce the number of
scheduled QR_EC work items.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Reported-and-tested-by: Alexander Mezin <mezin.alexander@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a platform refusing to respond QR_EC when SCI_EVT isn't set
(Acer Aspire V5-573G).
Currently, we rely on the behaviour that the EC firmware can respond
something (for example, 0x00 to indicate "no outstanding events") to
QR_EC even when SCI_EVT is not set, but the reporter has complained
about AC/battery pluging/unpluging and video brightness change delay
on that platform.
This is because the work item that has issued QR_EC has to wait until
timeout in this case, and the _Qxx method evaluation work item queued
after QR_EC one is delayed.
It sounds reasonable to fix this issue by:
1. Implementing SCI_EVT sanity check before issuing QR_EC in the EC
driver's main state machine.
2. Moving QR_EC issuing out of the work queue used by _Qxx evaluation
to a seperate IRQ handling thread.
This patch fixes this issue using solution 1.
By disallowing QR_EC to be issued when SCI_EVT isn't set, we are able to
handle such platform in the EC driver's main state machine. This patch
enhances the state machine in this way to survive with such malfunctioning
EC firmware.
Note that this patch can also fix CLEAR_ON_RESUME quirk which also relies
on the assumption that the platforms are able to respond even when SCI_EVT
isn't set.
Fixes: c0d653412f ACPI / EC: Fix race condition in ec_transaction_completed()
Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Reported-and-tested-by: Alexander Mezin <mezin.alexander@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, notify callbacks for fixed button events are run from
interrupt context. That is not necessary and after commit 0bf6368ee8
(ACPI / button: Add ACPI Button event via netlink routine) it causes
netlink routines to be called from interrupt context which is not
correct.
Also, that is different from non-fixed device events (including
non-fixed button events) whose notify callbacks are all executed from
process context.
For the above reasons, make fixed button device notify callbacks run
in process context which will avoid the deadlock when using netlink
to report button events to user space.
Fixes: 0bf6368ee8 (ACPI / button: Add ACPI Button event via netlink routine)
Link: https://lkml.org/lkml/2014/8/21/606
Reported-by: Benjamin Block <bebl@mageta.org>
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
[rjw: Function names, subject and changelog.]
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We generally don't allow ACPI drivers to bind to ACPI device objects
that companion "physical" device objects are created for to avoid
situations in which two different drivers may attempt to handle one
device at the same time. Recent ACPI device enumeration rework
extended that approach to ACPI PNP devices by starting to use a scan
handler for enumerating them. However, we previously allowed ACPI
drivers to bind to ACPI device objects with existing PNP device
companions and changing that led to functional regressions on some
systems.
For this reason, add a special check for PNP devices in
acpi_device_probe() so that ACPI drivers can bind to ACPI device
objects having existing PNP device companions as before.
Fixes: eec15edbb0 (ACPI / PNP: use device ID list for PNPACPI device enumeration)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81511
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81971
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: Dirk Griesbach <spamthis@freenet.de>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.
My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.
In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.
So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
For device tree based booting, we need to use wake-up
interrupts like we already do for some omaps. This fixes
a PM regression on beagleboard compared to legacy booting.
Tested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel has never supported clk32g as a regulator since it is a clock
and not a regulator. Fortunately nothing actually references this node so
we can just remove it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When an alias for a clock already exists the warning is printed. For
every module with a main_clk defined, a clk alias for fck is added.
There are some components that have the same main_clk defined, so this
is a really normal situation.
For example the am33xx edma device has 4 components using the same main
clock. So there are three warnings in the boot log for this already
existing clock alias:
platform 49000000.edma: alias fck already exists
platform 49000000.edma: alias fck already exists
platform 49000000.edma: alias fck already exists
As this is only interesting for developers, this patch changes the
message to a debug message.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.
By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.
With this change, the following now works:
interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
Fixes: 6e58b8f1da ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 65b97cf6b8 introduced in v3.7 caused a regression
by using a reversed CS_MASK thus causing omap_calculate_ecc to
always fail. As the NAND base driver never checks for .calculate()'s
return value, the zeroed ECC values are used as is without showing
any error to the user. However, this won't work and the NAND device
won't be guarded by any error code.
Fix the issue by using the correct mask.
Code was tested on omap3beagle using the following procedure
- flash the primary bootloader (MLO) from the kernel to the first
NAND partition using nandwrite.
- boot the board from NAND. This utilizes OMAP ROM loader that
relies on 1-bit Hamming code ECC.
Fixes: 65b97cf6b8 (mtd: nand: omap2: handle nand on gpmc)
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was used
for NAND on this board.
Commit c06c527016 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So revert back to
using software ECC scheme.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d039197 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.
This defect can be observed on the following boards during legacy boot
-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Highlights:
- More fixes for read/write codepath regressions
- Sleeping while holding the inode lock
- Stricter enforcement of page contiguity when coalescing requests
- Fix up error handling in the page coalescing code
- Don't busy wait on SIGKILL in the file locking code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2wRt
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highlights:
- more fixes for read/write codepath regressions
* sleeping while holding the inode lock
* stricter enforcement of page contiguity when coalescing requests
* fix up error handling in the page coalescing code
- don't busy wait on SIGKILL in the file locking code"
* tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
nfs: can_coalesce_requests must enforce contiguity
nfs: disallow duplicate pages in pgio page vectors
nfs: don't sleep with inode lock in lock_and_join_requests
nfs: fix error handling in lock_and_join_requests
nfs: use blocking page_group_lock in add_request
nfs: fix nonblocking calls to nfs_page_group_lock
nfs: change nfs_page_group_lock argument
This is to properly put to NULL the ptp_clock while un-register the PTP support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the IPC bit into the GMAC control register
that must be done after the core initialization otherwise it will
not have any effect.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Confine SH_INTC to platforms that need it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QSyy
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH driver fix from Simon Horman:
"Confine SH_INTC to platforms that need it"
* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
sh: intc: Confine SH_INTC to platforms that need it
Pull MIPS fixes from Ralf Baechle:
"Pretty much all across the field so with this we should be in
reasonable shape for the upcoming -rc2"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: OCTEON: make get_system_type() thread-safe
MIPS: CPS: Initialize EVA before bringing up VPEs from secondary cores
MIPS: Malta: EVA: Rename 'eva_entry' to 'platform_eva_init'
MIPS: EVA: Add new EVA header
MIPS: scall64-o32: Fix indirect syscall detection
MIPS: syscall: Fix AUDIT value for O32 processes on MIPS64
MIPS: Loongson: Fix COP2 usage for preemptible kernel
MIPS: NL: Fix nlm_xlp_defconfig build error
MIPS: Remove race window in page fault handling
MIPS: Malta: Improve system memory detection for '{e, }memsize' >= 2G
MIPS: Alchemy: Fix db1200 PSC clock enablement
MIPS: BCM47XX: Fix reboot problem on BCM4705/BCM4785
MIPS: Remove duplicated include from numa.c
MIPS: Add common plat_irq_dispatch declaration
MIPS: MSP71xx: remove unused plat_irq_dispatch() argument
MIPS: GIC: Remove useless parens from GICBIS().
MIPS: perf: Mark pmu interupt IRQF_NO_THREAD
Code manipulating sysfs symlinks on adjacent net_devices(s)
currently doesn't take into account that devices potentially
belong to different namespaces.
This patch trying to fix an issue as follows:
- check for net_ns before creating / deleting symlink.
for now only netdev_adjacent_rename_links and
__netdev_adjacent_dev_remove are affected, afaics
__netdev_adjacent_dev_insert implies both net_devs
belong to the same namespace.
- Drop all existing symlinks to / from all adj_devs before
switching namespace and recreate them just after.
Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
separate trampolines had a design flaw with the interaction between
the function and function_graph tracers.
The main flaw was the simplification of the use of multiple tracers having
the same filter (like function and function_graph, that use the
set_ftrace_filter file to filter their code). The design assumed that the
two tracers could never run simultaneously as only one tracer can be
used at a time. The problem with this assumption was that the function
profiler could be implemented on top of the function graph tracer, and
the function profiler could run at the same time as the function tracer.
This caused the assumption to be broken and when ftrace detected this
failed assumpiton it would spit out a nasty warning and shut itself down.
Instead of using a single ftrace_ops that switches between the function
and function_graph callbacks, the two tracers can again use their own
ftrace_ops. But instead of having a complex hierarchy of ftrace_ops,
the filter fields are placed in its own structure and the ftrace_ops
can carefully use the same filter. This change took a bit to be able
to allow for this and currently only the global_ops can share the same
filter, but this new design can easily be modified to allow for any
ftrace_ops to share its filter with another ftrace_ops.
The first four patches deal with the change of allowing the ftrace_ops
to share the filter (and this needs to go to 3.16 as well).
The fifth patch fixes a bug that was also caused by the new changes
but only for archs other than x86, and only if those archs implement
a direct call to the function_graph tracer which they do not do yet
but will in the future. It does not need to go to stable, but needs
to be fixed before the other archs update their code to allow direct
calls to the function_graph trampoline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT+hqSAAoJEKQekfcNnQGulvcH/0O4NMXX4HH1dQlYgKEaSYxE
Nh8WdiewopF5iaeNvo+8Nzdq8D2k3KgMOqSlzJ4JVmzd7gjOBSGeKDfqFwR+IbTk
9LcaJJCI3oG3MEf6m7gZMdjKPKyxkeYHDtG7kRHo8z94eliV9pKC6fUnEWayQO3o
Kv6IBupdkF8ICAiKRae5Uo0c9wjZ9YP0bZS7fxI2hJw3h/NMFnhnhUL03URIx8e3
dqgpweYg+P3KPfp2Jz6safdJqLTPK9rqqhkZhylbDl7o78xEzRN7wCyB6Nak00xz
swRgsW6vFP7ci/YSNx+B6HCIf7NTm3WLDrrIhitNHcJUZwUMU3CRO9IJHGsTuEE=
=J5lZ
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull fix for ftrace function tracer/profiler conflict from Steven Rostedt:
"The rewrite of the ftrace code that makes it possible to allow for
separate trampolines had a design flaw with the interaction between
the function and function_graph tracers.
The main flaw was the simplification of the use of multiple tracers
having the same filter (like function and function_graph, that use the
set_ftrace_filter file to filter their code). The design assumed that
the two tracers could never run simultaneously as only one tracer can
be used at a time. The problem with this assumption was that the
function profiler could be implemented on top of the function graph
tracer, and the function profiler could run at the same time as the
function tracer. This caused the assumption to be broken and when
ftrace detected this failed assumpiton it would spit out a nasty
warning and shut itself down.
Instead of using a single ftrace_ops that switches between the
function and function_graph callbacks, the two tracers can again use
their own ftrace_ops. But instead of having a complex hierarchy of
ftrace_ops, the filter fields are placed in its own structure and the
ftrace_ops can carefully use the same filter. This change took a bit
to be able to allow for this and currently only the global_ops can
share the same filter, but this new design can easily be modified to
allow for any ftrace_ops to share its filter with another ftrace_ops.
The first four patches deal with the change of allowing the ftrace_ops
to share the filter (and this needs to go to 3.16 as well).
The fifth patch fixes a bug that was also caused by the new changes
but only for archs other than x86, and only if those archs implement a
direct call to the function_graph tracer which they do not do yet but
will in the future. It does not need to go to stable, but needs to be
fixed before the other archs update their code to allow direct calls
to the function_graph trampoline"
* tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Use current addr when converting to nop in __ftrace_replace_code()
ftrace: Fix function_profiler and function tracer together
ftrace: Fix up trampoline accounting with looping on hash ops
ftrace: Update all ftrace_ops for a ftrace_hash_ops update
ftrace: Allow ftrace_ops to use the hashes from other ops
Commit f8ec894945 allowed external callers
use slot dropping logic, unfortunately it also broke external users of
input_mt_is_used() as we stopped incrementing frame count unless input
device was set up to automatically drop unused slots.
Fixes: f8ec894945 ("Input: MT - make slot cleanup callable outside
mt_sync_frame()")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=83081
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This verifies to truncate any allocated blocks, offset[0], by inline_data.
Not figured out, but for making sure.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Upstream commit:
95d76acc75 ("x86, irq: Count legacy IRQs by legacy_pic->nr_legacy_irqs instead of NR_IRQS_LEGACY")
removed reserved interrupts for the platforms that do not have a legacy IOAPIC.
Which breaks the boot on Intel MID platforms such as Medfield:
BUG: unable to handle kernel NULL pointer dereference at 0000003a
IP: [<c107079a>] setup_irq+0xf/0x4d [ 0.000000] *pdpt = 0000000000000000 *pde = 9bbf32453167e510
The culprit is an uncoditional setting of IRQ2 which is used
as cascade IRQ on legacy platforms. It seems we have to check
if we have enough legacy IRQs reserved before we can call
setup_irq().
The fix adds such check in native_init_IRQ() and in setup_default_timer_irq().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Link: http://lkml.kernel.org/r/1405931920-12871-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The stick is not recognized.
This dongle uses r8188eu but usb-id is missing.
3.16.0
Signed-off-by: Holger Paradies <retabell@gmx.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NFC will leak buffer if send failed.
Use single exit point that does the freeing
Cc: stable@vger.kernel.org #3.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If connect request is queued (e.g. device in pg) set client state
to initializing, thus avoid preliminary exit in wait if current
state is disconnected.
This is regression from:
commit e4d8270e60
Author: Alexander Usyskin <alexander.usyskin@intel.com>
mei: set connecting state just upon connection request is sent to the fw
CC: stable@vger.kernel.org # 3.15+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the default EP max packet value as 8 bytes, because in the case
of low-speed, 'ep_mps' is not set. Thus, the default value of 'ep_mps'
should be considered for the case of low-speed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The roothub's index per controller is from 0, but the hub port index per hub
is from 1, this patch fixes "can't find device at roohub" problem for connecting
test fixture at roohub when do USB-IF Embedded Host High-Speed Electrical Test.
This patch is for v3.12+.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the PCI ID a BCM43217 without a sprom.
This devices was found on a Netgear R6250 attached to a BCM4708 ARM SoC.
bcma: bus1: Found chip with id 0xA8D1, rev 0x00 and package 0x08
bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0)
bcma: bus1: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x14, class 0x0)
b43-phy0: Broadcom 43217 WLAN found (core revision 30)
b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 17
b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 14, Version 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds one more ACPI ID of a Broadcom bluetooth chip.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit 174beab7d4 ("at76c50x-usb: Don't perform DMA from stack memory")
at76_delete_device() and usb_put_dev() are called both
if at76_init_new_device() fails in at76_probe().
But at76_delete_device() does usb_put_dev(priv->dev) itself
that means double usb_put_dev().
The patch avoids the problem by moving usb_put_dev() from
at76_delete_device() to at76_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vlad Yasevich
Jonas Jensen
Michal Kubeček
Josef Bacik
Alan Cox
Lv Zheng
Lan Tianyu
Rafael J. Wysocki
Tony Lindgren
Mark Brown
Markus Pargmann
Hans Wennborg
Nishanth Menon
Roger Quadros
Linus Torvalds
Giuseppe CAVALLARO
Alexander Y. Fomichev
Larry Finger
Dmitry Torokhov
Jaegeuk Kim
Andy Shevchenko
Holger Paradies
Alexander Usyskin
Jingoo Han
Peter Chen
Hauke Mehrtens
Mika Westerberg
Maks Naumov
Alexey Khoroshilov