This adds Kconfig options for the Tegra30 AHUB and I2S controller, and
updates the Tegra+WM8903 machine driver Kconfig to select those.
Includes a squashed bugfix from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This provides an ASoC DAI interface for Tegra 30's I2S controller.
Includes a squashed bugfix from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AHUB (Audio Hub) is a mux/crossbar which links all audio-related
devices except the HDA controller on Tegra30. The devices include the
DMA FIFOs, DAM (Digital Audio Mixers), I2S controllers, and SPDIF
controller. Audio data may be routed between these devices in various
combinations as required by board design/application.
Includes a squashed bugfix from Nikesh Oswal <noswal@nvidia.com>
Includes squashed bugfixes from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Recent list discussions concluded that drivers should not be calling
of_have_populated_dt(), and hence of_have_populated_dt() should not be
exported. Use a different mechanism to detect DT vs. non-DT boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra30 has some additional clocks that need to be manipulated, names
some clocks differently, runs PLLs at different base rates, etc. The
utility code needs to handle this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize the audio clock tree appropriately for some reasonable rate.
This makes sure the PLLs etc. are actually programmed to something
reasonable when the audio driver is loaded.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename Tegra20-specific Kconfig variables, module filenames, all internal
symbol names, clocks, and platform devices, to reflect the fact the DAS
and I2S drivers are for a specific HW version.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename these files so they include a specific hardware version in their
filenames. The contents is only touched minimally so that git's rename
tracking operates correctly; renaming all symbols in the files results
in a diff so large that the rename detection fails.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without this, the Tegra20 drivers can be built into a kernel that's
built only for Tegra30.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAS, I2S, and SPDIF Kconfig options are intended to be selected by
the Kconfig options for ASoC machine drivers. As such, they don't need
to be user-visible themselves. Drop the description from the DAS variable
to achieve this. I2S and SPDIF already don't have a description.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clk_enable/disable() already reference count the enable calls, so there's
no need for the callers to do the same.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAS, I2S, and SPDIF drivers are Tegra20-specific. Group these
together so that when Tegra30-specific equivalents are added later, the
file ordering makes sense.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is mainly for symmetry with a future Tegra30 driver, where the
equivalent of the DAS (the AHUB) is useful separately from the I2S driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ERROR: trailing whitespace
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indent with TABs to be consistent with the rest of the file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These include aren't needed, and some of the files are about to be
renamed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously, the ASoC 'platform' (PCM/DMA) object was instantiated via a
platform_device. This didn't represent the hardware well, since there
was no separate hardware associated with this platform_device; it was a
virtual device with sole purpose to call snd_soc_register_platform().
This mechanism required all board files to register this device, and all
ASoC machine drivers to create and register this device when booting
using device tree.
This change removes the platform_device completely. Each Tegra DAI now
registers the ASoC 'platform' itself. Machine drivers are adjusted for
the new 'platform' name.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix comment indentation to clear checkpatch errors in a later patch.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following warning:
sound/soc/tegra/tegra_alc5632.c: In function 'tegra_alc5632_asoc_init':
sound/soc/tegra/tegra_alc5632.c:118:6: warning: unused variable 'ret' [-Wunused-variable]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALC5632 codec supports digital microphone. This patch adds DAPM widget.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All DAPM routes are configured via device tree, and there is no need in
DAPM route structures in board file.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is adding device tree support of headset autodetection on PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements device tree support for Tegra boards with ALC5632
codec.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a follow up on 53dea36c70 which fixes the other affected
pcm engines.
Description from 53dea36c70c1857:
Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.
Without this patch I was seeing null-pointer dereferenc in atmel-pcm.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver is parameterized in two ways:
a) Platform data, which supplies the set of GPIOs used by the driver.
These GPIOs can now be parsed out of device tree.
b) Machine-specific DAPM route arrays embedded into the ASoC machine
driver itself. Historically, the driver picks the appropriate array
to use using machine_is_*(). The driver now requires this array to
be parsed from device tree when instantiated through device tree,
using the core ASoC support for this parsing.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At this stage only Toshiba AC100/Dynabook supported.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move DAS routing setup into the DAS driver itself. This removes the need
to duplicate this in each machine driver, of which we'll soon have three.
An added advantage is that the machine drivers no longer call the Tegra20-
specific DAS functions by name, so the machine driver no longer needs to
be split up into Tegra20 and Tegra30 versions.
If individual machine drivers need a different routing setup to this
default, they can still call the DAS functions to set that up.
Long-term, DAS will be a codec driver, and user-space will be able to
control its routing, possibly within constraints that the machine driver
sets up. Configuring the DAS routing from the DAS driver is a very slight
move in that direction.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the module_platform_driver() macro which makes
the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also rename it to MICBIAS to reflect the pin name and help any out of tree
users notice the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Set card.fully_routed to request the ASoC core calculated unused codec
pins, and call snd_soc_dapm_nc_pin() for them. Remove the open-coded
calls.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set card.fully_routed to request the ASoC core calculated unused codec
pins, and call snd_soc_dapm_nc_pin() for them. Remove the open-coded
calls.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When devices are instantiated from device-tree, pdev->id is set to -1.
Rework the driver so it doesn't depend on the ID.
Tegra I2S instantiated from board files are configured with pdev
name "tegra-i2s" and ID 0 or 1. The driver core then names the
device "tegra-i2s.0" or "tegra-i2s.1". This is not changing.
When a device is instantiated from device-tree, it will have
pdev->name="" and pdev->id=-1. For this reason, the pdev->id value is
not something we can rely on.
This patch doesn't actually change any names though:
When a device is instantiated from device-tree, the overall device name
will be "${unit_address}.${node_name}". This causes issues such as
clk_get() failures due to lack of a device-name match. To solve that,
AUXDATA was invented, to force a specific device name, thus allowing
dev_name() to return the same as the non-device-tree case. Tegra
currently uses AUXDATA for the I2S controllers. Eventually, AUXDATA will
go away, most likely replaced by phandle-based references within the
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_driver saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_driver saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_drive saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This removes potentially machine-specific routing knowledge from the
I2S driverinto the machine drivers, which is better equipped to know
what the appropriate routing configuration is.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_drive saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes the following sparse warnings:
sound/soc/tegra/tegra_das.c:215:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_das.c:237:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_pcm.c:370:32: warning: symbol 'tegra_pcm_platform' was not declared. Should it be static?
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.
OMAP drivers are omitted as I know Peter already has patches for them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Board file support for Ventana is not yet mainlined, and probably won't
ever be given the move to Device-Tree. Consequently, the Ventana entry
is being removed from arch/arm/tools/mach-types in the next merge window,
since it was registered over a year ago.
This will also remove function machine_is_ventana(), which is used by
the ASoC Tegra WM8903 machine driver. This will cause compilation
failures. Drop Ventana support to resolve this.
Hopefully, in the not-too-distant future, tegra_wm8903.c will be able to
configure itself from Device-Tree, and hence we'll be able to re-instate
Ventana support just by creating a .dts file for the board.
Also note that Aebl support is in a similar boat. However, that board
isn't scheduled for deprecation for at least another 5 months, and
perhaps we will have completely removed non-Device-Tree support from
tegra_wm8903.c by then and/or adjusted mach-types policy.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two issues were preventing module snd-soc-tegra-wm8903.ko from being
removed and re-inserted:
a) The speaker-enable GPIO is hosted by the WM8903 chip. This GPIO must
be freed before snd_soc_unregister_card() is called, because that
triggers wm8903.c:wm8903_remove(), which calls gpiochip_remove(), which
then fails if any of the GPIOs are in use. To solve this, free all GPIOs
first, so the code doesn't care where they come from.
b) We need to call snd_soc_jack_free_gpios() to match the call to
snd_soc_jack_add_gpios() during initialization. Without this, the
call to snd_soc_jack_add_gpios() fails during any subsequent modprobe
and initialization, since the GPIO and IRQ are already registered. In
turn, this causes the headphone state not to be monitored, so the
headphone is assumed not to be plugged in, and the audio path to it is
never enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all PCM devices have all sub-streams. Specifically, the SPDIF driver
only supports playback and hence has no capture substream. Check whether
a substream exists before dereferencing it, when de-allocating DMA
buffers in tegra_pcm_deallocate_dma_buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This is a minimal driver for the Tegra SPDIF controller.
In hardware, the SPDIF output signal is always routed to any active HDMI
display controllers, and may also be routed to external pins on Tegra
using the pinmux.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The clock needed by the I2S driver is associated with the I2S device name
in the standard fashion. Hence, use clk_get(dev) instead of clk_get_sys(clk_name).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The I2S controller needs a clock to respond to register writes. Without
this, register writes will at worst hang the CPU. In practice, I've only
observed writes being dropped.
Luckily, the dropped register writes historically had no effect:
TEGRA_I2S_TIMING: The value we wrote was the reset default.
TEGRA_I2S_FIFO_SCR: The default was for the FIFOs to request more data
when one slot was empty. The requested value was for the FIFOs to request
when four slots were empty. The DMA controller in the mainline kernel is
configured to burst a single entry at a time into the FIFO, hence there
was no issue. The only negative effect was on bus efficiency losses due
to an increased number of arbitration attempts.
However, in various non-upstream changes, the DMA controller now bursts
four entries at a time into the FIFO. If there is only space for one
entry, the data is simply dropped. In practice, this resulted in 3/4 of
samples being dropped, and playback at 4x the expected rate and pitch.
By fixing the clocking issue, this is solved.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.
Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We want the default state of the HP_MUTE signal to be asserted, so that
the headphones are muted before the first audio playback. Without this,
the headphones are left unmuted until shortly after the first audio
playback completes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The prototype of the inline dummy version of tegra_i2s_debug_add
was not consistent with the real version.
Reported-by: Rhyland-Klein <rklein@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There needs to be a strong reason for overriding the Kconfig default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
CONFIG_SND_SOC_TEGRA_WM8903 is useful for many Tegra boards. To avoid the
ASoC tegra/Kconfig enumerating them all, instead have the Tegra machine
Kconfig select MACH_HAS_SND_SOC_TEGRA_WM8903 where appropriate, and have
SND_SOC_TEGRA_WM8903 depend on this.
[Redid ASoC diff so it applies. -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace calls to a variety of registration functions by updating
struct snd_soc_card snd_soc_tegra_wm8903 to directly point at the
various control/widget/map tables instead. The ASoC core now
performs any required registration based on these data fields.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Card widgets are created in the card's DAPM context, not any codec's DAPM
context. Hence, w->codec==NULL. Instead, find the card from the widget
through the DAPM context of the widget, not the codec of the widget.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only the clock programming code needs to know whether the clocks changed,
and that is encapsulated within tegra_asoc_utils_set_rate(). The machine
driver's call to snd_soc_dai_set_sysclk(codec_dai, ...) is safe
irrespective of whether the clocks changed.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the driver is not initialized/registered, nothing should be touching
these fields anyway, so there's no point clearing them out.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This machine driver is a platform driver, and hence will only be
instantiated on the correct machines. Hence, there is no need to
check the current machine during probe.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Ventana is identical to Harmony.
* Seaboard, Kaen, and Aebl are all pretty similar, mainly with slightly
different sets of GPIOs, and slightly different WM8903 pin connectivity.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Storing the struct in an array makes the assignments to the GPIO member a
little non-obvious, and is pointless when there's only a single GPIO.
(I thought I fixed this during the review cycle when first submitting this
driver, but I guess I overlooked that)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The previous commit renames SND_TEGRA_SOC_HARMONY to SND_TEGRA_SOC_WM8903.
While we're breaking people's .config files, rename all Tegra/SOC-related
Kconfig variables to be more consistent with at least the core codec
variables. Note that there exist machines that name their variables both
ways.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Soon, this machine driver will be updated to handle a number of Tegra boards
using the WM8903 codec. Rename the file in advance to reflect this.
Fix the content of tegra_wm8903.c to match the rename; replace references
to Harmony board with something more generic.
* s/struct tegra_harmony/struct tegra_wm8903/
* s/harmony/machine/ # variable name
* Similar rename for some functions
* Similar comment fix
* Similar MODULE_DESCRIPTION fix
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Soon, this machine driver will be updated to handle a number of Tegra boards
using the WM8903 codec. Rename the platform device in advance to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The audio driver will soon support more than just the Tegra Harmony board.
Rename the platform data header file and data type to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC machine drivers that are their own platform_driver (as opposed to
those using the soc-audio platform_driver) need to explicitly set up
power-management operation callbacks.
To avoid cut/paste, snd_soc_pm_ops also needs to be exported.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
tegra_dma_allocate_channel() returns NULL on errors, not an error pointer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The utilities will be required by every machine driver. Including the
utility object directly into every machine driver causes a build failure
if the modules are actually built into the kernel, since each will define
the symbols exported by the utility file. Solve this by moving the
utility object into a separate module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the appropriate MODULE_ALIAS in place, the audio modules will be
automatically loaded; there is no longer a need for manual modprobes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Harmony has both an external mic (a regular mic jack) and an internal mic
(a 0.1" two-pin header on the board).
The external mic is connected to the WM8903's IN1L pin, and is supported
by the current driver.
The internal mic is connected to the WM8903's IN1R pin, and is not supported
by the current driver.
It appears that no Harmony systems were shipped with any internal mic
connected; users were expected to provide their own. This makes the
internal mic connection less interesting.
The WM8903's Mic Bias signal is used for both of these mics. For each mic,
a GPIO drives a transistor which gates whether the mic bias signal is
actively connected to that mic, or isolated from it.
The dual use of the mic bias for both mics makes a general-purpose complete
implementation of mic detection using the mic bias complex. So, for
simplicity, the internal mic is currently ignored by the driver.
This patch configures the relevant GPIOs to enable the mic bias connection
to the external mic, and disable the mic bias connection to the internal
mic. Note that in practice, this is the default state if these GPIOs aren't
configured.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Add jack definition for mic jack
* Request wm8903 to enable mic detection
* Force mic bias on, since it's required for mic detection
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It causes noisy -codecs to appear in things like .codec_name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
gpio_set_value* should accept logic values not just 0 or 1. The WM8903 GPIO
driver has been fixed to work this way, so remove the redundant !!
previously required when it didn't accept values >1.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead, have the machine driver provide storage for the utility data
somehow.
For Harmony in particular, store this within struct tegra_harmony, itself
referenced by snd_soc_card's drvdata.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indent with TABs not spaces.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DAPM widget definitions for the internal speaker paths. Currently, this
path is always enabled while playback is active.
Add code to control the speaker amplifier GPIO.
The GPIO is requested during _init, since that's the first time it is
guaranteed that the WM8903 module is loaded, probed, and hence has exported
its GPIO chip.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously, snd-soc-tegra-harmony internally instantiated a platform device
object whenever the module was loaded. Instead, switch to a more typical model
where arch/arm/mach-tegra defines a platform device, and snd-soc-tegra-harmony
acts as a driver for such a platform device.
Define a new struct tegra_harmony to store driver data in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this change, I can capture from a microphone plugged into the
mic jack on Harmony (after unmuting Left Input PGA, and maybe turning
up the gain there too).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
That config variable doesn't exist in the mainline kernel, and hence
the dependency shouldn't either.
In linux-tegra-2.6.36, the dependency did exist to avoid a conflict with
the old non-ALSA Tegra I2S driver. However, this isn't and won't be
upstreamed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A recent discussion on linux-arm-kernel noted that the value returned by
clk_get_sys is an opaque token, and not strictly a pointer; it is
meaningful only to the clock API, clients should not dereference the value,
and the clock API must accept any non-IS_ERR value it returned.
Hence, only IS_ERR is appropriate to interpret the result, not
IS_ERR_OR_NULL.
I checked that clk_get_sys in both ASoC's for-next and Tegra's for-next
do behave as described; NULL is not returned in the case of error.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Everything else is using snd_soc_ so we should use it here too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many portions of Tegra ASoC machine drivers will be similar or identical.
To avoid cut/paste, this file will act as a repository for all that common
code. For now, it solely includes code to reprogram the audio PLL for
44.1KHz- vs. 48KHz-based sample rates.
Signed-Off-By: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This provides an ASoC DAI interface for Tegra's I2S controller.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This provides an ASoC platform driver that manages Tegra's APB DMA
controller.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAS (Digital Audio Switch) is a mux/crossbar which sits between
the DACs (Digital Audio Controllers) and the DAPs (Digital Audio
Ports). Audio data may be routed between DACs and DAPs in various
combinations as required by board design/application.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren
Stephen Warren
Leon Romanovsky
Joachim Eastwood
Axel Lin
Mark Brown
Lars-Peter Clausen
Paul Gortmaker
Olof Johansson
Liam Girdwood
Mike Rapoport