The device driver must allocate memory for IUCV buffers with GFP_DMA,
because IUCV cannot address memory above 2GB (31bit addresses only).
Because the IUCV ignores the higher bits of the address, sending and
receiving IUCV data with this driver might cause memory corruptions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Before you can read or write from the i6300esb memeory mapped registers,
you need to unlock these. This is done by writing the magic numbers 0x80
and 0x86 to the reload register. The size of the reload register is 32bit
though.
Also binary 11 is hex 0x03 and not 0x11.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This hooks up the ->set_affinity() for the INTC controllers, which can be
done as just a simple copy of the cpumask. The enable/disable paths
already handle SMP register strides, so we just test the affinity mask in
these paths to determine which strides to skip over.
The early enable/disable path happens prior to the IRQs being registered,
so we have no affinity mask established at that point, in which case we
just default to CPU_MASK_ALL. This is left as it is to permit the force
enable/disable code to retain existing semantics.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
msi-laptop uses rfkill*() interfaces so it should depend on RFKILL.
msi-laptop.c:(.text+0x1fcd1b): undefined reference to `rfkill_alloc'
msi-laptop.c:(.text+0x1fcd76): undefined reference to `rfkill_register'
msi-laptop.c:(.text+0x1fcdc8): undefined reference to `rfkill_destroy'
msi-laptop.c:(.text+0x1fcdd9): undefined reference to `rfkill_unregister'
This repairs "msi-laptop: Detect 3G device exists by standard ec command",
which is in some gregkh tree.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Detect 3G device exists by standard ec command. Driver will not create the threeg sysfs
file and threeg rfkill interface if there have no internal 3G device in MSI notebook/netbook.
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the resume method for set the load SCM flag after system reusme.
Without this patch, the wifi function key on SCM model will back to BIOS
control mode then confuse with the userland software control.
e.g. MSI N034
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some MSI 3G netbook only have one fn key to control Wlan/Bluetooth/3G,
those netbook will load the SCM (windows app) to disable the original
Wlan/Bluetooth control by BIOS when user press fn key, then control
Wlan/Bluetooth/3G by SCM (software control by OS). Without SCM, user
cann't on/off 3G module on those 3G netbook.
On Linux, msi-laptop driver will do the same thing to disable the
original BIOS control, then might need use HAL or other userland
application to do the software control that simulate with SCM.
e.g. MSI N034 netbook
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add threeg sysfs file for support query 3G state by standard 66/62 ec
command, the MSI standard ec interface supported this feature.
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Suppport standard ec 66/62 command on MSI notebook and nebook. MSI
netbook and notebook already support 66/62 command, so, add new
get_state function, and put the old model to non-standard model, but
driver still support those old model.
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the future, we are going to be changing the lock type for struct
device (once we get the lockdep infrastructure properly worked out) To
make that changeover easier, and to possibly burry the lock in a
different part of struct device, let's create some functions to lock and
unlock a device so that no out-of-core code needs to be changed in the
future.
This patch creates the device_lock/unlock/trylock() functions, and
converts all in-tree users to them.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alex Chiang <achiang@hp.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: CHENG Renquan <rqcheng@smu.edu.sg>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After merging the final tree, today's linux-next build (powerpc
allyesconfig) failed like this:
drivers/pci/pci-sysfs.c: In function 'pci_create_legacy_files':
drivers/pci/pci-sysfs.c:645: error: lvalue required as unary '&' operand
drivers/pci/pci-sysfs.c:658: error: lvalue required as unary '&' operand
Caused by commit "sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on
dynamic attributes" interacting with commit "sysfs: Use one lockdep
class per sysfs attribute") both from the driver-core tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't open code the renaming of symlinks in sysfs
instead use the new helper function sysfs_rename_link
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are the non-static sysfs attributes that exist on
my test machine. Fix them to use sysfs_attr_init or
sysfs_bin_attr_init as appropriate. It simply requires
making a sysfs attribute present to see this. So this
is a little bit tedious but otherwise not too bad.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function name must be followed by a space, hypen, space, and a
short description.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ben Nizette, the author of this driver, told me in a private mail that this
project has been cancelled. He suggested to remove the driver for now, and
will come back with a new version should the hardware really exist.
This patch completely removes the driver.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Two trivial fixes for the Userspace IO Kconfig file:
1) uio_sercos3 is a PCI driver, so let it depend on PCI.
2) "default n" under UIO_PCI_GENERIC is luxury since it is already the default.
Acked-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Userspace IO driver for netX-based fieldbus cards by
Hilscher (see http://www.hilscher.com). ATM, cifX and comX cards are
supported. The userspace part for this driver is provided by Hilscher
and should come with the card.
The driver is in use for several months now and has been tested by
people at Hilscher and Linutronix.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to cfag12864bfb_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avuton Olrich <avuton@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to omap24xxcam_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to omap_hdq_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to omap_i2c_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: chandra shekhar <x0044955@ti.com>
Cc: Jason P Marini <jason.marini@gmail.com>
Cc: Syed Mohammed Khasim <x0khasim@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to hp_wmi_bios_setup is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Frans Pop <elendil@planet.nl>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to a probe callback is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Alberto Mardegan <mardy@users.sourceforge.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andriy Skulysh <askulysh@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Frans Pop <elendil@planet.nl>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Helge Deller <deller@gmx.de>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ian Molton <spyro@f2s.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Kaj-Michael Lang <milang@tal.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: linux-fbdev-devel@lists.sourceforge.net
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Vincent Sanders <vince@simtec.co.uk>
Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: James Simmons <jsimmons@infradead.org>
Acked-by: Peter Jones <pjones@redhat.com>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to a probe callback is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Cc: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: peter fuerst <post@pfrst.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a warning on several pxa based machines:
arch/arm/mach-pxa/ssp.c:475: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Vikram Dhillon <dhillonv10@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These should be sysdev attributes, not class attributes. This patch
should resolve the problem.
Thanks to Stephen Rothwell for pointing out the problem.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Constify struct kset_uevent_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
base.h is used by base drivers for sharing internal structures.
Turns out firmware_class does not depend on it at all so remove it.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No longer fall back to "add" and warn, but always require a valid
action-string written to the "uevent" file.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No recent mainstream system uses the /sbin/hotplug fork-bomb any more.
Disable it by default to reflect how it is used these days.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All major distros enable devtmpfs on recent systems, so remove
the EXPERIMENTAL flag, and make the description a bit more instructive.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before unlinking the inode, reset the current permissions of possible
references like hardlinks, so granted permissions can not be retained
across the device lifetime by creating hardlinks, in the unusual case
that there is a user-writable directory on the same filesystem.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert some drivers who export a single string as class attribute
to the new class_attr_string functions. This removes redundant
code all over.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several drivers just export a static string as class attributes.
Use the new extensible attribute support to define a simple
CLASS_ATTR_STRING() macro for this.
This will allow to remove code from drivers in followon patches.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This attribute is really a sysdev_class attribute, not a plain class attribute.
They are identical in layout currently, but this might not always be
the case.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert the node driver to sysdev_class attribute arrays. This
greatly cleans up the code and remove a lot of code.
Saves ~150 bytes of code on x86-64.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use sysdev_class attribute arrays in node driver
Convert the node driver to sysdev_class attribute arrays. This
greatly cleans up the code and remove a lot of code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a attribute array that is automatically registered and unregistered
to struct sysdev_class. This is similar to what struct class has.
A lot of drivers add list of attributes, so it's better to do
this easily in the common sysdev layer.
This adds a new field to struct sysdev_class. I audited the
whole tree and there are no dynamically allocated sysdev classes,
so this is fully compatible.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using the new attribute argument convert the cpu driver class attributes
to carry the node state. Then use a shared function to do what a lot of
individual functions did before.
This eliminates an ugly macro.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using the new attribute argument convert the node driver class
attributes to carry the node state. Then use a shared function to do
what a lot of individual functions did before.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
Similar to sysdev_attributes and normal attributes.
This is a tree-wide sweep, converting everything in one go.
No functional changes in this patch other than passing the new
argument everywhere.
Tested on x86, the non x86 parts are uncompiled.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many legacy-style module create singleton platform devices themselves,
along with corresponding platform driver. Instead of replicating error
handling code in all such drivers, provide a helper that allocates and
registers a single platform device and a driver and binds them together.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is creating several devices in cuse class concurrently and with
CONFIG_SYSFS_DEPRECATED turned off, it triggers the following oops.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000038
IP: [<ffffffff81158b0a>] sysfs_addrm_start+0x4a/0xf0
PGD 75bb067 PUD 75be067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/system/cpu/cpu7/topology/core_siblings
CPU 1
Modules linked in: cuse fuse
Pid: 4737, comm: osspd Not tainted 2.6.31-work #77
RIP: 0010:[<ffffffff81158b0a>] [<ffffffff81158b0a>] sysfs_addrm_start+0x4a/0xf0
RSP: 0018:ffff88000042f8f8 EFLAGS: 00010296
RAX: ffff88000042ffd8 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff880007eef660 RDI: 0000000000000001
RBP: ffff88000042f918 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: ffffffff81158b0a R12: ffff88000042f928
R13: 00000000fffffff4 R14: 0000000000000000 R15: ffff88000042f9a0
FS: 00007fe93905a950(0000) GS:ffff880008600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000038 CR3: 00000000077c9000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process osspd (pid: 4737, threadinfo ffff88000042e000, task ffff880007eef040)
Stack:
ffff880005da10e8 0000000011cc8d6e ffff88000042f928 ffff880003d28a28
<0> ffff88000042f988 ffffffff811592d7 0000000000000000 0000000000000000
<0> 0000000000000000 0000000000000000 ffff88000042f958 0000000011cc8d6e
Call Trace:
[<ffffffff811592d7>] create_dir+0x67/0xe0
[<ffffffff811593a8>] sysfs_create_dir+0x58/0xb0
[<ffffffff8128ca7c>] ? kobject_add_internal+0xcc/0x220
[<ffffffff812942e1>] ? vsnprintf+0x3c1/0xb90
[<ffffffff8128cab7>] kobject_add_internal+0x107/0x220
[<ffffffff8128cd37>] kobject_add_varg+0x47/0x80
[<ffffffff8128ce53>] kobject_add+0x53/0x90
[<ffffffff81357d84>] device_add+0xd4/0x690
[<ffffffff81356c2b>] ? dev_set_name+0x4b/0x70
[<ffffffffa001a884>] cuse_process_init_reply+0x2b4/0x420 [cuse]
...
The problem is that kobject_add_internal() first adds a kobject to the
kset and then try to create sysfs directory for it. If the creation
fails, it remove the kobject from the kset. get_device_parent()
accesses class_dirs kset while only holding class_dirs.list_lock to
see whether the cuse class dir exists. But when it exists, it may not
have finished initialization yet or may fail and get removed soon. In
the above case, the former happened so the second one ends up trying
to create subdirectory under NULL sysfs_dirent.
Fix it by grabbing a mutex in get_device_parent().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Colin Guthrie <cguthrie@mandriva.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console:
virtio: console: Use better variable names for fill_queue operation
virtio: console: Fix type of 'len' as unsigned int
* 'for-linus/i2c' of git://git.fluff.org/bjdooks/linux:
i2c: Add support for Xilinx XPS IIC Bus Interface
i2c: omap: Add support for 16-bit registers
i2c-pnx: fix setting start/stop condition
powerpc: doc/dts-bindings: update doc of FSL I2C bindings
i2c-mpc: add support for the MPC512x processors from Freescale
i2c-mpc: rename "setclock" initialization functions to "setup"
i2c-mpc: use __devinit[data] for initialization functions and data
i2c/imx: don't add probe function to the driver struct
i2c: Add support for Ux500/Nomadik I2C controller
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: Convert sh to use read/update_persistent_clock
sh: Move PMB debugfs entry initialization to later stage
sh: Fix up flush_cache_vmap() on SMP.
sh: fix up MMU reset with variable PMB mapping sizes.
sh: establish PMB mappings for NUMA nodes.
sh: check for existing mappings for bolted PMB entries.
sh: fixed virt/phys mapping helpers for PMB.
sh: make pmb iomapping configurable.
sh: reworked dynamic PMB mapping.
sh: Fix up cpumask_of_pcibus() for the NUMA build.
serial: sh-sci: Tidy up build warnings.
sh: Fix up ctrl_read/write stragglers in migor setup.
serial: sh-sci: Add DMA support.
dmaengine: shdma: extend .device_terminate_all() to record partial transfer
sh: merge sh7722 and sh7724 DMA register definitions
sh: activate runtime PM for dmaengine on sh7722 and sh7724
dmaengine: shdma: add runtime PM support.
dmaengine: shdma: separate DMA headers.
dmaengine: shdma: convert to platform device resources
dmaengine: shdma: fix DMA error handling.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: use __ratelimit in unaligned.c
parisc: Convert to read/update_persistent_clock
parisc: Simplify param.h by including <asm-generic/param.h>
parisc: drop unnecessary cast in __ldcw_align() macro
parisc: add strict copy size checks (v2)
parisc: remove trailing space in messages
parisc: ditto sys_accept4
parisc: wire up sys_recvmmsg
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Provide generic subsystem-level callbacks
PM / Runtime: Document power.runtime_auto and related functions
If we were unable to detect a PHY on any of the MDIO bus id we tried instead of
bailing out with -ENODEV, assume the MAC is connected to a switch and use MDIO
bus 0. This unbreaks quite a lot of devices out there whose switch cannot be
detected.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite what the comment above CPMAC_SKB_SIZE says, the hardware also
needs to account for the FCS length in a received frame. This patch fix
the receiving of 802.1q frames which have 4 more bytes. While at it
unhardcode the definition and use the one from if_vlan.h.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one removes trailing whitespace in pegasus.h and more importantly
adds new Pegasus compatible device.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the call to kcalloc() fails then we should return -ENOMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"skb" is alway non-null here, but even if it were null the check isn't
needed because dev_kfree_skb() can handle it.
This eliminates a smatch warning about dereferencing a variable before
checking that it is non-null.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix a race at the end of NAPI processing in ks8695_poll() function.
Signed-off-by:Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a reference to regs-sys.h got missed in the reorganisation of
the Samsung platform headers targetted for 2.6.34.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for the Xilinx XPS IIC Bus Interface.
The driver uses the dynamic mode, supporting to put several
I2C messages in the FIFO to reduce the number of interrupts.
It has the same feature as ocores, it can be passed a list
of devices that will be added when the bus is probed.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The current i2c-omap driver is set up for 32-bit registers, which
corresponds to most OMAP devices. However, OMAP730/850 based
devices use a 16-bit register size.
This change modifies the driver to perform a runtime CPU type check
to determine the register sizes, and uses a bit shift of either 1
or 2 bits to compute the proper register sizes for all registers.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The start/stop condtions are set in different places repetedly in the i2c-pnx
driver. Beside in i2c_pnx_start and i2c_pnx_stop the start/stop bit are also
set during the transfer of a i2c message in the master_xmit/rcv calls. This is
wrong since we can't set the start/stop condition during the transaction of a
single message any way. As a matter of fact, the driver will sometimes set both
the start and the stop bits at one time. This can be easily reproduced by
sending a simple read request like e.g
struct i2c_msg msgs[] = {
{ addr, 0, 1, buf },
{ addr, I2C_M_RD, offset, buf }
};
While processing the first message the i2c_pnx_master_xmit will set both the
start_bit and the stop_bit, which will eventually confuse the slave.
Fixed by remove setting start/stop condition from the transmit routines.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As I2C interrupts must be enabled for the MPC512x by the setup function
as well, "fsl,preserve-clocking" is handled in a slighly different way.
Also, the old settings are now reported calling dev_dbg(). For the
MPC512x the clock setup function of the MPC52xx can be re-used.
Furthermore, the Kconfig help has been updated and corrected.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
To prepare support for the MPC512x processors from Freescale the
"setclock" initialization functions have been renamed to "setup"
because I2C interrupts must be enabled for the MPC512x by this
function as well.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
"__devinit[data]" has not yet been used for all initialization functions
and data. To avoid truncating lines, the struct "mpc_i2c_match_data" has
been renamed to "mpc_i2c_data", which is even the better name.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Having a pointer to the probe function is unnecessary when using
platform_driver_probe and yields a section mismatch warning after
removing the white list entry "*driver" for
{ .data$, .data.rel$ } -> { .init.* } mismatches in modpost.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds support for ST-Ericsson's I2C block found
in Ux500 and Nomadik 8815 platforms.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch fixes a build failure[1], by adding the missing semaphore.h include
References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2234322/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.
Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert i2c-isch to platform_device for the lpc mfd core to add it at probe
time.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.
Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the state of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM8350 interrupt infrastructure hooked
up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
New function twl4030_remove_script(u8 flags) takes a script type as
defined in twl.h and prevents any script already loaded in that position
from running. This is accomplished by programming SEQ_ADD_* to 0x3f,
the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags.
(Future) users of this function include OMAP board files for machines
facing a race condition between sleep and warm reset.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM
processors. While at it, make CONFIG_TMIO_MMC depend on
CONFIG_MFD_SH_MOBILE_SDHI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add MMC_CAP_MMC_HIGHSPEED support to the sh_mobile_sdhi
driver. Also, remove type cast and FIXME comment.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the chip default but it's possible the bootloader or OTP
will have been configured to a different mode (eg, to provide
feedback during startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wm831x_gpio_direction_output() ignored the state passed into it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds cell->disable() calls to the tmio-mmc
probe() error handling and the remove() function.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch changes the tmio_mmc driver to wait 100ms
before checking the card detect status. This type of
delay is quite common among mmc drivers, it seems that
most hardware platforms need to give the hardware some
time to settle before checking card availabilty.
Hotplug is half-broken without this patch on the sh7724
Ecovec board. Hot insertion seems ok but eject is never
detected without this patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On SuperH platforms the SDHI controller does not produce any command IRQs after
a completed IO. This leads to card-detect interrupts staying disabled. Do not
disable card-detect interrupts on DATA IRQs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add base address for generic slave ID0, ID1, ID2
and introduced one more entry to align RTC module number between
twl4030 and twl6030
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to
use only the external HW resistor >=470 Ohm for the assured
functionality in HS mode.
While testing the I2C in High Speed mode, it was discovered that
without a proper pull-up resistor, there is data corruption during
multi-byte transfer. RTC(time_set) test case was used for testing.
From the analysis done, it was concluded that ideally we need a
pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for
assured performance in HS mode.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Intel Poulsbo (SCH) chipset LPC bridge controller contains several
functions. Creating and MFD driver for the LPC bridge controller allows
simultaneous use of SMBus and GPIO interfaces on the SCH.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For ACPI based systems, we should check for ACPI conflicts when adding the
platform devices. The test will always succeed for non ACPI platforms.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Change the typo CONFIG_INPUT_TWL4030_PWBUTTON_MODULE in the
twl_has_pwrbutton definition to CONFIG_INPUT_TWL4030_PWRBUTTON_MODULE.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of
mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the
touchscreen driver of 88pm860x since IRQ handling is changed.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes wrong goto statement for error handling on probe.
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use i2c_dummy in 88pm860x driver to avoid using static in probe function.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8925 is a PMIC that contains charger component
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8925 is a PMIC that contains RTC component.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update thread irq handler. Simply the interface of using thread irq.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update I2C driver in order to fit all of three I2C components in max8925.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Variable remap was incorrectly referencing remap_off for the remap_sleep
case when configuring TWL4030 power scripts.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8994 is a highly integrated ultra low power audio hub CODEC.
Since it includes on-board regulators and GPIOs it is represented
as a multi-function device, though the overwhelming majority of
the functionality is provided by the ASoC CODEC driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
htc-i2cpld should depend on GPIOLIB, otherwise there are many
build errors:
drivers/mfd/htc-i2cpld.c:50: error: field 'chip_out' has incomplete type
drivers/mfd/htc-i2cpld.c:54: error: field 'chip_in' has incomplete type
drivers/mfd/htc-i2cpld.c:243: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:243: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:278: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:278: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:282: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:282: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:315: error: dereferencing pointer to incomplete type
drivers/mfd/htc-i2cpld.c:322: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:322: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:467+: error: dereferencing pointer to incomplete type [19X]
drivers/mfd/htc-i2cpld.c:490: error: implicit declaration of function 'gpiochip_add'
drivers/mfd/htc-i2cpld.c:504: error: implicit declaration of function 'gpiochip_remove'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TWL4030_BCI_BATTERY config option originates from a patch to the
omap git tree. However inclusion in linux was seemingly rejected and
the functionality nears inclusion under a different name so this
removes the bits of the old version that made it into the mainline
kernel again.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes the aged and unreachable debugfs code in the AB3100
OTP driver so that it's (A) reachable and (B) works. Bug detected
in parallell by Christoph Egger using VAMOS and Robert P. J. Day
by his kernel scanning script.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This reintroduces the entropy sampling of the AB3100 IRQ as the
IRQF_SAMPLE_RANDOM is going out according to the feature removal
schedule. I'm trying to do this the right way then, so CC:ing some
random people for a quick review. We add entropy for interrupt
events in the AB3100 which are truly random in nature, like
external cables being connected, voltages on batteries dropping
below certain ranges, ADC triggers or overheating.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Robin Getz <rgetz@blackfin.uclinux.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This change introduces a driver for the HTC PLD chip found
on some smartphones, such as the HTC Wizard and HTC Herald.
It works through the I2C bus and acts as a GPIO extender.
Specifically:
* it can have several sub-devices, each with its own I2C
address
* Each sub-device provides 8 output and 8 input pins
* The chip attaches to one GPIO to signal when any of the
input GPIOs change -- at which point all chips must be
scanned for changes
This driver implements the GPIOs throught the kernel's
GPIO and IRQ framework. This allows any GPIO-servicing
drivers to operate on htcpld pins, such as the gpio-keys
and gpio-leds drivers.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add subdevs in MAX8925. MAX8925 includes regulator, backlight and touch
components.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Basic Max8925 support, which is a power management IC from Maxim
Semiconductor.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the support 88PM8607 A0/A1 stepping. There's some register
definition changes in B0 stepping. It can make software more efficient.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable touchscreen driver for the 88pm860x multi function core.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable led sub device in Marvell 88PM860x. Two LED arrays can be supported.
Each LED array can be used for R,G,B leds.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
At most, three backlight device can be supported in 88pm860x driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM860x is a complex PMIC device. It contains touch, charger, sound, rtc,
backlight, led, and so on.
Host communicates to 88PM860x by I2C bus. Use thread irq to support this
usage case.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename 88PM8607 to 88PM860X in both Makefile and Kconfig under mfd directory.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM8606 and 88PM8607 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according to
requirement.
There's some logic tightly linked between these two chips. For example, USB
charger driver needs to access both chips by I2C interface.
Now share one driver to these two devices. Only one I2C client is identified
in platform init data. If another chip is also used, user should mark it in
companion_addr field of platform init data. Then driver could create another
I2C client for the companion chip.
All I2C operations are accessed by 860x-i2c driver. In order to support both
I2C client address, the read/write API is changed in below.
reg_read(client, offset)
reg_write(client, offset, data)
The benefit is that client drivers only need one kind of read/write API. I2C
and MFD driver can be shared in both 8606 and 8607.
Since API is changed, update API in 8607 regulator driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Create 88pm8607-i2c driver to support all I2C operation of 88PM8607.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This converts the AB3100 core MFD driver to use a threaded
interrupt handler instead of the explicit top/bottom-half
construction with a workqueue. This saves some code and make it
more similar to other modern MFD drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The headphone detect and charger are using the IRQ numbers so need
to take account of irq_base with the genirq conversion. I obviously
picked the wrong system for initial testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq implementation does not allow modules to implement irq_chips
so the conversion of WM8350 to genirq means we can no longer allow the
driver to be built as a module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This gives us use of the diagnostic facilities genirq provides and
will allow implementation of interrupt support for the WM8350 GPIOs.
Stub functions are provided to ease the transition of the individual
drivers, probably after additional work to pass the IRQ numbers via
the struct devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Unlike the wm8350-custom code genirq nests enable and disable calls
so we can't just unconditionally mask or unmask the interrupt,
we need to remember the state we set and only mask or unmask when
there is a real change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The structure t7l66xb should not be freed before the subsequent references
to its fields in the arguments to clk_put. Furthermore, this structure is
allocated near the beginning of the function, and a goto to the label
err_noirq appears after a successful allocation, so it would seem that the
kfree should be moved down below this label.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e;
identifier f;
iterator I;
statement S;
@@
*kfree(x);
... when != &x
when != x = e
when != I(x,...) S
*x->f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Use resource_size() for ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use resource_size() for ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The requested memory region is smaller than the actual ioremap().
Use resource_size() to get the correct size.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The recent rework of /proc/bus/usb/devices polling support made
this structure unused so let's remove it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit a069c266ae.
It turns ou that not only was it missing a case (XFS) that needed it,
but perhaps more importantly, people sometimes want to enable new
modules that they hadn't had enabled before, and if such a module uses
list_sort(), it can't easily be inserted any more.
So rather than add a "select LIST_SORT" to the XFS case, just leave it
compiled in. It's not all _that_ big, after all, and the inconvenience
isn't worth it.
Requested-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Don Mullis <don.mullis@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Making this instance static exposes the code to SMP races, etc.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Platform device drivers can use the .shutdown method to handle soft
shutdown's instead of reboot_notifier's.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Upgrade the upstream driver from 2.0.0.0 to 2.1.2.1.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When IO is completed with underrun and with good SCSI status, check if
the transferred bytes against scsi_cmnd->underflow, which is set to
minimum number of bytes that must be transferred for this command, if
is less than required minimum, complete the IO with DID_ERROR.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
MS module did not invoke fdmi offline in all cases,
call fdmi offline when ms module receives a port offline,
so that fdmi offline is from one place in the ms module.
Make changes to handle 10G speed in the conversion routine.
Replaced the usage of bfa_adapter_attr_s struct with specific API's.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modified the portstats get/clear logic for port physical/FCoE/QoS stats.
Added more stats to FC
Fixed some issues with FCoE stats collection.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_ioc_attr_s is a big structure and some times could cause
stack overflow if defined locally, so add specific APIs that
are needed to replace the use of ioc_attr local var.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Rename pport structures to fcport in BFA FCS, to resolve confusion
about the port structures in the firmware, and make sure the SG page
is setup correctly.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently BFA was not checking for IOC down condition when issuing
getstats/clearstats
Add check to see if IOC is operational, before issuing
getstats/clearstats.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use dummy interrupt handlers till chip initialization is complete.
Install real interrupt handlers after chip initialization.
Also removed msix installation code in bfa_iocfc_init().
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed the issue of not acknowledging the command queue
full-to-non-full interrupt. Implemented separate acknowledging
functions for different ASIC and interrupt mode.
Fixed the case of missing CPE interrupt by always processing the
pending requests in the completion path.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ioc_recover failed to work in fcmode.
Fixed the code to initialize the ioc_regs.err_set during the
notify_hbfail.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace enum types with int and rearrange the fields to fix some
alignment issue.
Local var ioc_attr is causing the stack to overflow, so removed the
usage of the local ioc_attr var and now invoking an API to return the
ioc_type.
Fix some AEN issues.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Introduce a link notification state machine to handle next incoming
link events while the current event is being delivered to the driver.
When the event has been processed by the driver, the link notification
state machine will queue the next event (if there is any) to the
driver.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Made FCS authentication related changes to state machines and header
files.
Made changes in FCS state machines to handle the case when secret
string is NULL.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Changed PCI VPD to incorporate specific OEM vendors.
Added FCoE specific interrupt latency and delay params.
Added some variables needed by FIP 2.0.
Added some new logging and tracing definitions.
Added reserved members to make the structures (IOC, IOCFC) 64bit aligned.
Changed the module identifiers, as some files were moved.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Copy fpma MAC when requested by user space application. Added FPMA
mac address to the lport attributes structure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Make sure that in direct attach mode, we do not query the name server
after a target is marked offline.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace bfa_assert() with bfa_sm_fault() to get unhandled events for
debugging.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for faster IOC recovery after failure.
Split bfa_ioc.c into three files:
bfa_ioc.c: Common code shared between crossbow and catapult ASIC's.
bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and
interrupt related routines.
bfa_ioc_ct.c: Code specific to the catapult, reg mapping and
interrupt related routines.
Fix to make sure IOC reinitialize's properly on enable request -
update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd
timeout.
Makefile changes to support the 2 newly added files bfa_ioc_cb.c and
bfa_ioc_ct.c.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The caller of usbfs_conn_disc_event() in some cases (but not always)
already holds usbfs_mutex, so trying to protect the event counter with
that lock causes nasty deadlocks.
The problem was introduced by commit 554f76962d ("USB: Remove BKL from
poll()") when the BLK protection was turned into using the mutex instead.
So fix this by using an atomic variable instead. And while we're at it,
get rid of the atrocious naming of said variable and the waitqueue it is
associated with.
This also cleans up the unnecessary locking in the poll routine, since
the whole point of how the pollwait table works is that you can just add
yourself to the waiting list, and then check the condition you're
waiting for afterwards - avoiding all races.
It also gets rid of the unnecessary dynamic allocation of the device
status that just contained a single word. We should use f_version for
this, as Dmitry Torokhov points out. That simplifies everything
further.
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are subsystems whose power management callbacks only need to
invoke the callbacks provided by device drivers. Still, their system
sleep PM callbacks should play well with the runtime PM callbacks,
so that devices suspended at run time can be left in that state for
a system sleep transition.
Provide a set of generic PM callbacks for such subsystems and
define convenience macros for populating dev_pm_ops structures.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm raid1: fix deadlock when suspending failed device
dm: eliminate some holes data structures
dm ioctl: introduce flag indicating uevent was generated
dm: free dm_io before bio_endio not after
dm table: remove unused dm_get_device range parameters
dm ioctl: only issue uevent on resume if state changed
dm raid1: always return error if all legs fail
dm mpath: refactor pg_init
dm mpath: wait for pg_init completion when suspending
dm mpath: hold io until all pg_inits completed
dm mpath: avoid storing private suspended state
dm: document when snapshot has finished merging
dm table: remove dm_get from dm_table_get_md
dm mpath: skip activate_path for failed paths
dm mpath: pass struct pgpath to pg init done
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (23 commits)
hwmon: Remove the deprecated adt7473 driver
hwmon: Fix off-by-one kind values
hwmon: (tmp421) Fix temperature conversions
hwmon: (tmp421) Restore missing inputs
hwmon: Driver for Andigilog aSC7621 family monitoring chips
hwmon: (adt7411) Improve locking
hwmon: Add driver for ADT7411 voltage and temperature sensor
hwmon: (w83793) Add watchdog functionality
hwmon: (g760a) Make rpm_from_cnt static
hwmon: (it87) Validate auto pwm settings
hwmon: (it87) Add support for old automatic fan speed control
hwmon: (it87) Drop dead web links in documentation
hwmon: (it87) Add an entry in MAINTAINERS
hwmon: (it87) Use strict_strtol instead of simple_strtol
hwmon: (it87) Fix many checkpatch errors and warnings
hwmon: (it87) Add support for beep on alarm
hwmon: (it87) Create vid attributes by group
hwmon: (it87) Refactor attributes creation and removal
hwmon: (it87) Expose the PWM/temperature mappings
hwmon: (it87) Display fan outputs in automatic mode as such
...
* git://git.infradead.org/ubi-2.6:
UBI: add write checking
UBI: simplify debugging return codes
UBI: fix attaching error path
UBI: support attaching by MTD character device name
UBI: mark few variables as __initdata
The cs5535-gpio driver's get() function was returning the output value.
This means that the GPIO pins would never work as an input, even if
configured as an input.
The driver should return the READ_BACK value, which is the sensed line
value. To make that work when the direction is 'output', INPUT_ENABLE
needs to be set.
In addition, the driver was not disabling OUTPUT_ENABLE when the direction
is set to 'input'. That would cause the GPIO to continue to drive the pin
if the direction was ever set to output.
This issue was noticed when attempting to use the gpiolib driver to read
an external input. I had previously been using the char/cs5535-gpio
driver.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org> [2.6.33.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders controlled by the pca953x driver are able to
report changes on the input pins through an *INT pin.
This patch implements the irq_chip functionality (edge detection only).
The driver has been tested on an Arcom Zeus.
[akpm@linux-foundation.org: the compiler does inlining for us nowadays]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce support for triggering interrupts on both rising and falling
edge.
This feature requires version 3 or newer of the IP, a version check is
done when triggering on both edges is requested.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpio_request() without initial configuration of the GPIO is normally
useless, introduce gpio_request_one() together with GPIOF_ flags for
input/output direction and initial output level.
gpio_{request,free}_array() for multiple GPIOs.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the MAX7300-I2C variant of the MAX7301-SPI version. Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part. The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The else part of the if statement is indented but does not have braces
around it. It clearly should since it uses clk_enable and clk_disable
which are supposed to balance.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is to protect from interrupt handlers using an unregistered rtc
device.
To assert that the reset irq is considered now before the rtc is
registered the corresponding status is checked before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver for the mc13783 rtc needs to know if the TODA irq is pending.
Instead of tracking in the rtc driver if the irq is enabled provide that
information, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mc13783_ackirq, mc13783_unmask and mc13783_mask are deprecated, use the
drop in replacements with the nicer names.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the source file group these functions together.
The mc13783 header file provides fallback implementations for the old
names to prevent build failures. When all users of the old names are
fixed to use the new names these can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The idr should be destroyed when the module is unloaded. Found with
kmemleak.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning of
the declaration specifiers in a declaration is an obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memset should be given the size of the structure, not the size of the
pointer.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
expression E;
@@
memset(x, E, sizeof(
+ *
x))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function pcf2123_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix issue with rtc device not getting unregistered in probe error path.
Use the devres managed resource functions in the probe routine to cleanup
the error path.
Use sysfs_{create/remove}_group to add/remove the sysfs files.
Reduces the text size by 132 bytes, increases data by 12 bytes:
text data bss dec hex filename
- 937 124 0 1061 425 rtc-ep93xx.o
+ 805 136 0 941 3ad rtc-ep93xx.o
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Free pdata before exit. Found by cppcheck.
[yuasa@linux-mips.org: add missing iounmap()]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the xen support drivers are displayed in the main Device Drivers
menu of the config tools instead of in their own sub-menu, so move them to
their own sub-menu, like the rest of the driver world uses.
This keeps the main Device Drivers menu from becoming messy.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
warning: symbol 'vgacon_text_mode_force' was not declared. Should it be static?
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BuraphaLinux reported that we will trigger a mm warning when we
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=65536, this is because mm cann't
allocate so many pages. We should limit the range of
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE, don't give a user any chance to
trigger that.
Reported-by: BuraphaLinux Server <buraphalinuxserver@gmail.com>
Tested-by: BuraphaLinux Server <buraphalinuxserver@gmail.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While testing an ADC121S021 in an embedded board with a S3C2142 SoC (ARM
core), I have found that the 'adcxx' driver does not handle correctly
single channel ADCs from this chip family. For single channel chips you
must only issue one read transfer for correct measurement.
Signed-off-by: Jose Miguel Goncalves <jose.goncalves@inov.pt>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This card reader doesn't advertise, however DMA works well. Probably
windows SDHCI driver assumes that all readers support DMA and thus we see
that bug.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Norbert Preining <preining@logic.at>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() accepts a pointer to any location in the page so we do not
need the subtraction and cast.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to manage features and differences on a per-cpu basis. As several
cpus share the same mci revision, this patch aggregates cpus that have the
same IP revision in one defined constant. We use the
at91mci_is_mci1rev2xx() funtion name not to mess with newer Atmel sd/mmc
IP called "MCI2". _rev2 naming could have been confusing...
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the datasheets AT91SAM9261 does not support SDIO interrupts,
and AT91SAM9260/9263 have an erratum requiring 4bit mode while using slot
B for the interrupt to work.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is setting some max_ variables for the IO elevator, so the
elevator will put requests for large data blocks to the driver. This is
critical for
a) speed
and
b) wear leveling of the flash chip controller: Otherwise the controller
will treat the SD card badly with millions of single 4 KByte write
commands. This will lead to a shorter life time for the SD cards.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the read to use the DMA buffer as well. The old code was doing
double-buffering DMA with the PDC; no way to make it work. Replace it
with a single-PDC approach. It also simplify things removing the need for
a pre_dma_read() function.
[nicolas.ferre@atmel.com coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TX DMA buffer is allocated only once, because the
allocation/deallocation of the buffer for EACH chunk of data is
time-consuming and prone to memory fragmentation.
Using a coherent DMA buffer avoids extra data cache calls.
[nicolas.ferre@atmel.com: coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two timeout errors, one for slow SDHC cards and one for slow users
while inserting SD cards.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes two pointer errors, one which leads to memory overwrites if used
with large chunks of data.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero. As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin. Which of course will fail and makes the driver
unusable
Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin. This patch restores that behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And bring them back to 4-bit mode during resume.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards may suspend while keeping function interrupts active
especially in the powered suspend case. Upon resume we need to kick the
SDIO interrupt thread to check for pending interrupts and to restart card
IRQ detection at the host controller level.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid
sending CMD3/5/7 on a resume where power has been maintained, because the
8686 will refuse to respond to them and the MMC stack will give up on the
card.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested with an XO v1.5 from OLPC.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series provides the core changes needed to allow SDIO cards to
remain powered and active while the host system is suspended, and let them
wake up the host system when needed. This is used to implement
wake-on-lan with SDIO wireless cards at the moment. Patches to add that
support to the libertas driver will be posted separately.
This patch:
Some SDIO cards have the ability to keep on running autonomously when the
host system is suspended, and wake it up when needed. This however
requires that the host controller preserve power to the card, and
configure itself appropriately for wake-up.
There is however 4 layers of abstractions involved: the host controller
driver, the MMC core code, the SDIO card management code, and the actual
SDIO function driver. To make things simple and manageable, host drivers
must advertise their PM capabilities with a feature bitmask, then function
drivers can query and set those features from their suspend method. Then
each layer in the suspend call chain is expected to act upon those bits
accordingly.
[akpm@linux-foundation.org: fix typo in comment]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sdhci_set_adma_desc() is using byte-writes to write data in a specified
order into memory. Change to using __le16 for the two byte and __le32 for
the four byte cases and use the cpu_to_{le16,le32} to do the conversion
before writing.
This will reduce the size of the code and the number of writes as we no
longer need to chop the data up before writing.
As an example on ARM S3C64XX SoC, in little-endian configuration:
000000d4 <sdhci_set_adma_desc>:
- d8: e1a0c423 lsr ip, r3, #8
- dc: e1a0ec21 lsr lr, r1, #24
- e0: e1a04821 lsr r4, r1, #16
- e4: e1a05421 lsr r5, r1, #8
- e8: e1a06442 asr r6, r2, #8
- ec: e5c0c001 strb ip, [r0, #1]
- f0: e5c0e007 strb lr, [r0, #7]
- f4: e5c04006 strb r4, [r0, #6]
- f8: e5c05005 strb r5, [r0, #5]
- fc: e5c01004 strb r1, [r0, #4]
- 100: e5c06003 strb r6, [r0, #3]
- 104: e5c02002 strb r2, [r0, #2]
- 108: e5c03000 strb r3, [r0]
+ d4: e5801004 str r1, [r0, #4]
+ d8: e1c030b0 strh r3, [r0]
+ dc: e1c020b2 strh r2, [r0, #2]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to write the ADMA descriptor into memory is repeated several
times throughout sdhci_adma_table_pre, and thus should be moved into a
common function. This will also be useful if the patch to make the write
more efficient is accepted.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards expect byte transfers not to exceed the configured block
transfer size. Add a quirk to that effect.
Patches to make use of this quirk will be sent separately.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hardcoded value doesn't really work for all cards.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The host/Kconfig file is only included when MMC is selected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local sg variable is only used with BF54x code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This prevents those without an Atmel chip having a line in kernel
configuration which says "Atmel SD/MMC Driver" without any option.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 8bit MMC cards. The controller data width is configurable
depending on the wires setting in the platform data structure.
MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM.
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Build list_sort() only for configs that need it -- those that don't save
~581 bytes (i386).
Signed-off-by: Don Mullis <don.mullis@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add adds a debugfs interface and additional failure modes to LKDTM to
provide similar functionality to the provoke-crash driver submitted here:
http://lwn.net/Articles/371208/
Crashes can now be induced either through module parameters (as before)
or through the debugfs interface as in provoke-crash.
The patch also provides a new "direct" interface, where KPROBES are not
used, i.e., the crash is invoked directly upon write to the debugfs
file. When built without KPROBES configured, only this mode is available.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Cc: M. Mohan Kumar <mohan@in.ibm.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable priv is initialized twice to the same (side effect-free)
expression. Drop one initialization.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the CS5535 MFGPT hrtimer kconfig option to be with the other MFGPT
options. This makes it easier to find and also removes it from the main
"Device Drivers" menu, where it should not have been.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder struct menu_device to remove 8 bytes of padding on 64 bit builds.
Size drops from 136 to 128 bytes, so possibly needing one fewer cache
lines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A memmap is a directory in sysfs which includes 3 text files: start, end
and type. For example:
start: 0x100000
end: 0x7e7b1cff
type: System RAM
Interface firmware_map_add was not called explicitly. Remove it and add
function firmware_map_add_hotplug as hotplug interface of memmap.
Each memory entry has a memmap in sysfs, When we hot-add new memory, sysfs
does not export memmap entry for it. We add a call in function add_memory
to function firmware_map_add_hotplug.
Add a new function add_sysfs_fw_map_entry() to create memmap entry, it
will be called when initialize memmap and hot-add memory.
[akpm@linux-foundation.org: un-kernedoc a no longer kerneldoc comment]
Signed-off-by: Shaohui Zheng <shaohui.zheng@intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use of get_irq_chip_data() et al. requires including linux/irq.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch corrects author and copyright notices following the split-up of
the GE Fanuc joint venture.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It's possible that the platform is not allowing reboot via TCO timer
expiration.
Also, differentiate between not finding a chipset that has TCO, and the case
where TCO is present but the driver fails to initialize for some reason.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Clean-up driver:
* make release the reverse of probe so that both are consistent
* add WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS ioctls.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver adds support for the max63{69,70,71,72,73,74} family of
watchdog timer chips.
It has been tested on an Arcom Zeus (max6369).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Technologic Systems TS-72xx SBCs have external glue logic
CPLD which includes watchdog timer. This driver implements
kernel support for that.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
To prevent deadlock, bios in the hold list should be flushed before
dm_rh_stop_recovery() is called in mirror_suspend().
The recovery can't start because there are pending bios and therefore
dm_rh_stop_recovery deadlocks.
When there are pending bios in the hold list, the recovery waits for
the completion of the bios after recovery_count is acquired.
The recovery_count is released when the recovery finished, however,
the bios in the hold list are processed after dm_rh_stop_recovery() in
mirror_presuspend(). dm_rh_stop_recovery() also acquires recovery_count,
then deadlock occurs.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Eliminate a 4-byte hole in 'struct dm_io_memory' by moving 'offset' above the
'ptr' to which it applies (size reduced from 24 to 16 bytes). And by
association, 1-4 byte hole is eliminated in 'struct dm_io_request' (size
reduced from 56 to 48 bytes).
Eliminate all 6 4-byte holes and 1 cache-line in 'struct dm_snapshot' (size
reduced from 392 to 368 bytes).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Set a new DM_UEVENT_GENERATED_FLAG when returning from ioctls to
indicate that a uevent was actually generated. This tells the userspace
caller that it may need to wait for the event to be processed.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Free the dm_io structure before calling bio_endio() instead of after it,
to ensure that the io_pool containing it is not referenced after it is
freed.
This partially fixes a problem described here
https://www.redhat.com/archives/dm-devel/2010-February/msg00109.html
thread 1:
bio_endio(bio, io_error);
/* scheduling happens */
thread 2:
close the device
remove the device
thread 1:
free_io(md, io);
Thread 2, when removing the device, sees non-empty md->io_pool (because the
io hasn't been freed by thread 1 yet) and may crash with BUG in mempool_free.
Thread 1 may also crash, when freeing into a nonexisting mempool.
To fix this we must make sure that bio_endio() is the last call and
the md structure is not accessed afterwards.
There is another bio_endio in process_barrier, but it is called from the thread
and the thread is destroyed prior to freeing the mempools, so this call is
not affected by the bug.
A similar bug exists with module unloads - the module may be unloaded
immediately after bio_endio - but that is more difficult to fix.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove unused parameters(start and len) of dm_get_device()
and fix the callers.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Only issue a uevent on a resume if the state of the device changed,
i.e. if it was suspended and/or its table was replaced.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If all mirror legs fail, always return an error instead of holding the
bio, even if the handle_errors option was set. At present it is the
responsibility of the driver underneath us to deal with retries,
multipath etc.
The patch adds the bio to the failures list instead of holding it
directly. do_failures tests first if all legs failed and, if so,
returns the bio with -EIO. If any leg is still alive and handle_errors
is set, do_failures calls hold_bio.
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch pulls the pg_init path activation code out of
process_queued_ios() into a new function.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When suspending the device we must wait for all I/O to complete, but
pg-init may be still in progress even after flushing the workqueue
for kmpath_handlerd in multipath_postsuspend.
This patch waits for pg-init completion correctly in
multipath_postsuspend().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
m->queue_io is set to block processing I/Os, and it needs to be kept
while pg-init, which issues multiple path activations, is in progress.
But m->queue is cleared when a path activation completes without error
in pg_init_done(), even while other path activations are in progress.
That may cause undesired -EIO on paths which are not complete activation.
This patch fixes that by not clearing m->queue_io until all path
activations complete.
(Before the hardware handlers were moved into the SCSI layer, pg_init
only used one path.)
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'suspended' flag in struct multipath was introduced to check whether
the multipath target is in suspended state, but the same check is
done through dm_suspended() now, so remove the flag and related code.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the dm_get() in dm_table_get_md() because dm_table_get_md() could
be called from presuspend/postsuspend, which are called while
mapped_device is in DMF_FREEING state, where dm_get() is not allowed.
Justification for that is the lifetime of both objects: As far as the
current dm design/implementation, mapped_device is never freed while
targets are doing something, because dm core waits for targets to become
quiet in dm_put() using presuspend/postsuspend. So targets should be
able to touch mapped_device without holding reference count of the
mapped_device, and we should allow targets to touch mapped_device even
if it is in DMF_FREEING state.
Backgrounds:
I'm trying to remove the multipath internal queue, since dm core now has
a generic queue for request-based dm. In the patch-set, the multipath
target wants to request dm core to start/stop queue. One of such
start/stop requests can happen during postsuspend() while the target
waits for pg-init to complete, because the target stops queue when
starting pg-init and tries to restart it when completing pg-init. Since
queue belongs to mapped_device, it involves calling dm_table_get_md()
and dm_put(). On the other hand, postsuspend() is called in dm_put()
for mapped_device which is in DMF_FREEING state, and that triggers
BUG_ON(DMF_FREEING) in the 2nd dm_put().
I had tried to solve this problem by changing only multipath not to
touch mapped_device which is in DMF_FREEING state, but I couldn't and I
came up with a question why we need dm_get() in dm_table_get_md().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds two minor fixes while processing device mapper path activation.
Skip failed paths while calling activate_path. If the path is already failed
then activate_path will fail for sure. We don't have to call in that case. In
some case this might cause prolonged retries unnecessarily.
Change the misleading message if the path being activated fails with SCSI_DH_NOSYS.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes some unnecessary argument casting. There is no
functional change with this patch.
Passes 'struct pgpath' through to pg_init_done() instead of the enclosed
'struct dm_path'.
Tested the changes with LSI storage..
CC: Chandra Seetharaman <chandra.seetharaman@us.ibm.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make the run-time power management of PCI devices be inactive by
default by calling pm_runtime_forbid() for each PCI device during its
initialization. This setting may be overriden by the user space with
the help of the /sys/devices/.../power/control interface.
That's necessary to avoid breakage on systems where ACPI-based
wake-up is known to fail for some devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently s2io is dumping debug messages using the interface name
before it was allocated, showing a message like the following:
s2io: eth%d: Ring Mem PHY: 0x7ef80000
s2io: s2io_reset: Resetting XFrame card eth%d
This patch just fixes it, printing the pci bus information for
the card instead of the interface name.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when receiving a particular type of NFS v2 UDP traffic, the hardware could
DMA some bad data and then hang, possibly corrupting memory.
Disable the NFS parsing in this hardware, verified to fix the bug.
Originally reported and reproduced by RedHat's Neil Horman
CC: nhorman@tuxdriver.com
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The typhoon driver was incorrectly using smp_wmb() to order memory
accesses against IO to the NIC in a few instances. Use wmb() instead,
which is required to actually order between memory types.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Brown <davidb@quicinc.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (33 commits)
quota: stop using QUOTA_OK / NO_QUOTA
dquot: cleanup dquot initialize routine
dquot: move dquot initialization responsibility into the filesystem
dquot: cleanup dquot drop routine
dquot: move dquot drop responsibility into the filesystem
dquot: cleanup dquot transfer routine
dquot: move dquot transfer responsibility into the filesystem
dquot: cleanup inode allocation / freeing routines
dquot: cleanup space allocation / freeing routines
ext3: add writepage sanity checks
ext3: Truncate allocated blocks if direct IO write fails to update i_size
quota: Properly invalidate caches even for filesystems with blocksize < pagesize
quota: generalize quota transfer interface
quota: sb_quota state flags cleanup
jbd: Delay discarding buffers in journal_unmap_buffer
ext3: quota_write cross block boundary behaviour
quota: drop permission checks from xfs_fs_set_xstate/xfs_fs_set_xquota
quota: split out compat_sys_quotactl support from quota.c
quota: split out netlink notification support from quota.c
quota: remove invalid optimization from quota_sync_all
...
Fixed trivial conflicts in fs/namei.c and fs/ufs/inode.c
adt7473 driver is obsoleted by adt7475 driver. And it is scheduled
to be removed in Feb 2010.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Recent changes on the I2C front have left off-by-one array indexes in
3 hwmon drivers. Fix them.
Faulty commit:
e5e9f44c2 i2c: Drop I2C_CLIENT_INSMOD_2 to 8
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
The low bits of temperature registers are status bits, they must be
masked out before converting the register values to temperatures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
An off-by-one error caused some inputs to not be created by the driver
when they should. TMP421 gets only one input instead of two, TMP422
gets two instead of three, etc. Fix the bug by listing explicitly the
number of inputs each device has.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
Hwmon driver for Andigilog aSC7621 family monitoring chips.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add proper locking for the cached variables. Also get rid of
ref_is_vdd, which became obsolete.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add basic support for the ADT7411. Reads out all conversion results (via I2C,
SPI yet missing) and allows some on-the-fly configuration. Tested with a
custom board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add watchdog functionality to the Winbond W83793 driver.
Signed-off-by: Sven Anders <anders@anduras.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function rpm_from_cnt is only used internally so it can be made
static. Make it inline while we're here, for performance reasons
(although hopefully gcc would figure out by itself...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Before switching to automatic fan control mode, make sure that all the
trip points make sense. Otherwise, the control loop could lead to
weird fan behavior.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the automatic fan speed control interface as
implemented by IT8705F chips up to revision F and IT8712F chips up to
revision G. This implementation fits very well in our standard sysfs
interface.
I implemented the old and not the new interface because the only chip
I have at hand is an old one, and the new interface is more difficult
to map to the standard sysfs interface. Adding support later should be
possible though, if someone with a supported chip is interested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix 20 errors and 11 warnings reported by the checkpatch script. The
remainining errors would require more work. The remaining warnings
will be addressed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT87xxF chips support beeping on alarm, if properly wired and
configured. There is one control bit for each input type (temperature,
fan, voltage.) Let the user see and change them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only VID-related attributes are left in it87_attributes_opt, so we
might as well rename it to it87_attributes_vid and use this group to
create all attributes at once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a lot of code redundancy in the creation of the fan and
pwm attributes. Move these attributes to arrays so that the code can
be simplified.
This in turns makes the attributes removal code larger, so move it to
a separate function that can be called in both the standard removal
case and the error path during probing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the user read the PWM-to-temperature mappings. Until the trip
points are also exposed, this is essentially a way to know how the
BIOS has set things up. The ability to change the settings will be
added later, together with the trip points.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't yet support automatic fan control. Let it at
least tell the user when a fan output is in automatic mode. Also let
the user switch from automatic mode (possibly set by the BIOS) to
manual mode and back without losing the settings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested successfully with an ADM1032 chip on its evaluation board. It
should work fine with all other chips as well.
At this point this is more of a proof-of-concept, we don't do anything
terribly useful on SMBus alert: we simply log the event. But this could
later evolve into libsensors signaling so that user-space applications
can take an appropriate action.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
Restore the chip configuration when unloading the driver. This ensures
we don't leave the chip running if it was initially stopped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This chips is found on several Zotac Ion ITX boards, amongst others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: MC Matti <mcmatti17@googlemail.com>
Cc: Manuel Lamotte-Schubert <mls@pronego.com>
Process out and in prox events for Graphire and Tablet PC devices
in the same loop to simplify the data parsing logic.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Get rid of the transfer dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.
Rename the now static low-level dquot_transfer helper to __dquot_transfer
and vfs_dq_transfer to dquot_transfer to have a consistent namespace,
and make the new dquot_transfer return a normal negative errno value
which all callers expect.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
The wireless core made a number of api changes that caused
the winbond driver to break. This patch fixes those errors by
making the needed changes to the driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were a number of patches that went into Linus's
tree already that conflicted with other changes in the
staging branch. This merge resolves those merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6: (49 commits)
drivers/ide: Fix continuation line formats
ide: fixed section mismatch warning in cmd640.c
ide: ide_timing_compute() fixup
ide: make ide_get_best_pio_mode() static
via82cxxx: use ->pio_mode value to determine pair device speed
tx493xide: use ->pio_mode value to determine pair device speed
siimage: use ->pio_mode value to determine pair device speed
palm_bk3710: use ->pio_mode value to determine pair device speed
it821x: use ->pio_mode value to determine pair device speed
cs5536: use ->pio_mode value to determine pair device speed
cs5535: use ->pio_mode value to determine pair device speed
cmd64x: fix handling of address setup timings
amd74xx: use ->pio_mode value to determine pair device speed
alim15x3: fix handling of UDMA enable bit
alim15x3: fix handling of DMA timings
alim15x3: fix handling of command timings
alim15x3: fix handling of address setup timings
ide-timings: use ->pio_mode value to determine fastest PIO speed
ide: change ->set_dma_mode method parameters
ide: change ->set_pio_mode method parameters
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
init: Open /dev/console from rootfs
mqueue: fix typo "failues" -> "failures"
mqueue: only set error codes if they are really necessary
mqueue: simplify do_open() error handling
mqueue: apply mathematics distributivity on mq_bytes calculation
mqueue: remove unneeded info->messages initialization
mqueue: fix mq_open() file descriptor leak on user-space processes
fix race in d_splice_alias()
set S_DEAD on unlink() and non-directory rename() victims
vfs: add NOFOLLOW flag to umount(2)
get rid of ->mnt_parent in tomoyo/realpath
hppfs can use existing proc_mnt, no need for do_kern_mount() in there
Mirror MS_KERNMOUNT in ->mnt_flags
get rid of useless vfsmount_lock use in put_mnt_ns()
Take vfsmount_lock to fs/internal.h
get rid of insanity with namespace roots in tomoyo
take check for new events in namespace (guts of mounts_poll()) to namespace.c
Don't mess with generic_permission() under ->d_lock in hpfs
sanitize const/signedness for udf
nilfs: sanitize const/signedness in dealing with ->d_name.name
...
Fix up fairly trivial (famous last words...) conflicts in
drivers/infiniband/core/uverbs_main.c and security/tomoyo/realpath.c
Turns out that multiple people sent pretty much the same patch
for the same staging drivers. Commit these in two different
branches and merge them together to get a more complete coverage
of the cleanup and properly credit everyone for the work that they
did.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/battery-2.6:
power_supply: bq27x00: fix voltage and current units
power_supply: bq27x00: add status and time properties
power_supply: bq27x00: add BQ27500 support
power_supply: bq27x00: fix temperature conversion
power_supply: bq27x00: remove unused struct fields
power_supply: bq27x00: remove double endian swap
da9030_battery: fix spelling in comment
wm97xx_battery: Clean up some warnings
This fixes some code style issues about assignments in if conditions.
Signed-off-by: Chihau Chau <chihau@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes some code style issues like to add one space after a while or
switch statement and before a open parenthesis '(', and to include KERN_
facility level in the printk() functions.
Signed-off-by: Chihau Chau <chihau@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: do not initialise externals to 0 or NULL
+int comedi_num_legacy_minors = 0;
WARNING: braces {} are not necessary for single statement blocks
+ if (s->subdev_flags & SDF_CMD_READ) {
+ kill_fasync(&dev->async_queue, SIGIO, POLL_IN);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (s->subdev_flags & SDF_CMD_WRITE) {
+ kill_fasync(&dev->async_queue, SIGIO, POLL_OUT);
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_labpc.c file that fixes suspect code indent for
conditional statements found by the checkpatch.pl tool
Signed-off-by: Stewart Robertson <stewart_r@aliencamel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_labpc.c file that fixes up all the brace
warnings found by the checkpatch.pl tool
Signed-off-by: Maurice Dawson <mauricedawson2699@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_labpc.c file that fixes up a brace warning
found by the checkpatch.pl tool
Signed-off-by: Maurice Dawson <mauricedawson2699@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_labpc.c file that fixes up a brace warning
found by the checkpatch.pl tool.
Signed-off-by: Maurice Dawson <maurice2699@btinternet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes some coding style issues like include KERN_ facility levels
in some printk() and one trailing whitespace error.
Signed-off-by: Chihau Chau <chihau@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes some code style issues like else staments after the close
braces '}' and to use __func__ instead of __FUNCTION__.
Signed-off-by: Chihau Chau <chihau@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes all the errors and the majority of the warnings found with
checkpatch.pl script in hfa384x.h, following Gábor Stefanik hints
Signed-off-by: Alessandro Ghedini <al3xbio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes some coding style issues like to use __func__ instead
__FUNCTION__, "foo *bar" instead "foo* bar" and a initial comment with
"/* */" instead "//"
Signed-off-by: Chihau Chau <chihau@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_660x.c file that fixes up the brace and 80
character issues found by the checkpatch tool
Signed-off-by: Graham M Howe <gmhowe@btopenworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_65xx.c file that fixes up a brace
warning found by the checkpatch.pl tool
Signed-off-by: Graham M Howe <gmhowe@btopenworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the pcmad comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a line over 80 characters and a brace warnings.
Signed-off-by: Chihau Chau <chihau@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (27 commits)
Regulators: wm8400 - cleanup platform driver data handling
Regulators: wm8994 - clean up driver data after removal
Regulators: wm831x-xxx - clean up driver data after removal
Regulators: pcap-regulator - clean up driver data after removal
Regulators: max8660 - annotate probe and remove methods
Regulators: max1586 - annotate probe and remove methods
Regulators: lp3971 - fail if platform data was not supplied
Regulators: tps6507x-regulator - mark probe method as __devinit
Regulators: tps65023-regulator - mark probe method as __devinit
Regulators: twl-regulator - mark probe function as __devinit
Regulators: fixed - annotate probe and remove methods
Regulators: ab3100 - fix probe and remove annotations
Regulators: virtual - use sysfs attribute groups
twl6030: regulator: Configure STATE register instead of REMAP
regulator: Provide optional dummy regulator for consumers
regulator: Assume regulators are enabled if they don't report anything
regulator: Convert fixed voltage regulator to use enable_time()
regulator: Add WM8994 regulator support
regulator: enable max8649 regulator driver
regulator: trivial: fix typos in user-visible Kconfig text
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (151 commits)
vga_switcheroo: disable default y by new rules.
drm/nouveau: fix *staging* driver build with switcheroo off.
drm/radeon: fix typo in Makefile
vga_switcheroo: fix build on platforms with no ACPI
drm/radeon: Fix printf type warning in 64bit system.
drm/radeon/kms: bump the KMS version number for square tiling support.
vga_switcheroo: initial implementation (v15)
drm/radeon/kms: do not disable audio engine twice
Revert "drm/radeon/kms: disable HDMI audio for now on rv710/rv730"
drm/radeon/kms: do not preset audio stuff and start timer when not using audio
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
...
Fixed trivial conflicts in drivers/gpu/vga/Kconfig
My previous patch (655ffee284) added locking in
a bad way. Because rndis_set_oid can sleep, there is need to prepare multicast
addresses into local buffer under netif_addr_lock first, then call
rndis_set_oid outside. This caused reorganizing of the whole function.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
bfad.c & bfad_drv.h:
* Created a kernel thread from pci_probe that does the bfad start
operations after BFA init done on a firmware mismatch.
* The kernel thread on a fw mismatch waits for an event from IOC
call back and is woken up from bfa_cb_init() on BFA init success.
* In normal cases of no firmware mismatch this thread is terminated
in pci_probe.
bfa_fcs_lport.c, fabric.c, fcs_lport.h & vport.c:
* Split the lport init to attach time and init time code, so that
proper config attributes are set after firmware mismatch.
bfa_iocfc.c:
* Handle an IOC timer issue, where the IOC timer would expire before
the init completion and send Init fail event to the driver,
however IOC init continues and completes successfully at the later
stage. The bfa and driver were not handling this kind of deferred
init completion.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Brocade CNA currently supports only 190 vports (instead of 191),
since there are only 192 unicast cam entries reserved for FCoE.
Brocade CNA has a total of 256 unicast cam entries (192 FCoE + 64 LL)
192 cam entries = 1 burned in mac + 1 baseport FPMA mac + 190 vport
FPMA macs.
Made changes to the code to support only 190 vports.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Split bfa_fcs_init() into bfa_fcs_attach() and bfa_fcs_init().
Removed empty function definitions in FCS modules
Modified driver to call bfa_fcs_attach() and bfa_fcs_init() as needed.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added a FCS function to be called during driver init, to set the FDMI
Driver parameter.
fdmi.c: Created a disabled state when fdmi is disabled.
bfad.c:
* Added fdmi_enable driver parameter.
* Added support to call bfa_fcs_set_fdmi_param() to initialize fcs
fdmi setting.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_intr.c: Enable new halt interrupt in BFA.
bfi_ctreg.h: Expose new halt interrupt bit definition to host.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_ioc.c:
- Enable IOC auto-recovery by default.
- When CNA is in FC mode, return IOC type as FC (not FCoE)
bfa_iocfc.c:
- Set fcmode before pci initialization/setup.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear virtual links was not propagated upwards to bfa from fw.
This resulted in HBA and switch being in an inconsistent state.
So defined a new LPS event for clear virtual link on a vport,
and also now clear virtual link on a baseport, is sent as a
link down event from the fw.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added separate MSI-X module parameters to selectively
enable / disable MSI-X interrupts for both Brocade HBA and CNA's.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
queue restart tasklets need to be stopped after napi handlers are stopped
since the latter can restart them. So stop them after stopping napi.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit a3bc1f11e9 ("gianfar: Revive SKB
recycling") gianfar driver sooner or later stops transmitting any
packets on SMP machines.
start_xmit() prepares new skb for transmitting, generally it does
three things:
1. sets up all BDs (marks them ready to send), except the first one.
2. stores skb into tx_queue->tx_skbuff so that clean_tx_ring()
would cleanup it later.
3. sets up the first BD, i.e. marks it ready.
Here is what clean_tx_ring() does:
1. reads skbs from tx_queue->tx_skbuff
2. checks if the *last* BD is ready. If it's still ready [to send]
then it it isn't transmitted, so clean_tx_ring() returns.
Otherwise it actually cleanups BDs. All is OK.
Now, if there is just one BD, code flow:
- start_xmit(): stores skb into tx_skbuff. Note that the first BD
(which is also the last one) isn't marked as ready, yet.
- clean_tx_ring(): sees that skb is not null, *and* its lstatus
says that it is NOT ready (like if BD was sent), so it cleans
it up (bad!)
- start_xmit(): marks BD as ready [to send], but it's too late.
We can fix this simply by reordering lstatus/tx_skbuff writes.
Reported-by: Martyn Welch <martyn.welch@ge.com>
Bisected-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Martyn Welch <martyn.welch@ge.com>
Cc: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Cc: Stable <stable@vger.kernel.org> [2.6.33]
Signed-off-by: David S. Miller <davem@davemloft.net>
r8169 needs certain writes to be visible to other CPUs or the NIC before
touching the hardware, but was using smp_wmb() which is only required to
order cacheable memory access. Switch to wmb() which is required to
order both cacheable and non-cacheable memory.
Noticed by Catalin Marinas and Paul Mackerras.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to keep track of the number of buffers added to a vq. Use
nr_added_bufs instead of 'ret'.
Also, the users of fill_queue() overloaded a local 'err' variable to
check the numbers of buffers allocated. Use nr_added_bufs instead of
err.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
We declare 'len' as int type but it should be 'unsigned int', as
get_buf() wants it to be.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
If the calling convention of ->timer_fn() and ->cleanup_fn() are unified
across hardware versions we can drop parameters to ioat_init_channel() and
unify ioat_is_dma_complete() implementations.
Both ->timer_fn() and ->cleanup_fn() are modified to expect a struct
dma_chan pointer.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The hardware automatically disables further interrupts after each event
until rearmed. This allows a delay to be injected between the occurence
of the interrupt and the running of the cleanup routine. The delay is
scaled by the descriptor backlog and then written to the INTRDELAY
register which specifies the number of microseconds to hold off
interrupt delivery after an interrupt event occurs. According to
powertop this reduces the interrupt rate from ~5000 intr/s to ~150
intr/s per without affecting throughput (simple dd to a raid6 array).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since ioat_cleanup_preamble() and the update of the last completed
descriptor are not synchronized there is a chance that two cleanup threads
can see descriptors to clean. If the first cleans up all pending
descriptors then the second will trigger the BUG_ON.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 9c1390a923ddb6fba1cf9d7440743369140c6d8a replaced
all u_int's with u32 and u_long's with u64. Unfortunately, a u_long
is still only 32-bits so they should have been replaced with u32 also.
This can be verified by the register definitions in dt3155_io.h. It
specifically states that the memory mapped registers are 32-bit.
Fix this by changing all the u64 to u32.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
+#include <asm/io.h>
WARNING: braces {} are not necessary for any arm of this statement
+ if (dev->driver) {
[...]
+ } else {
[...]
WARNING: braces {} are not necessary for single statement blocks
+ if (insn->insn == INSN_READ) {
+ data[0] = (new_data[1] >> (chan - base_bitfield_channel)) & 1;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (async->prealloc_buf && async->prealloc_bufsz == new_size) {
+ return 0;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (async->buf_page_list[i].virt_addr == NULL) {
+ break;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if ((int)(async->buf_write_alloc_count + nbytes - free_end) > 0) {
+ nbytes = free_end - async->buf_write_alloc_count;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if ((int)(async->buf_write_alloc_count + nbytes - free_end) > 0) {
+ nbytes = 0;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (async->buf_write_ptr >= async->prealloc_bufsz) {
+ async->buf_write_ptr %= async->prealloc_bufsz;
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: do not use C99 // comments
+ volatile u_char radioModule;// shows EEPROM, can be overridden at 0x111
ERROR: do not use C99 // comments
+ volatile u_char defaultChannelSet; // shows EEProm, can be overriiden at 0x10A
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: space prohibited between function name and open parenthesis '('
+void MD4Init (MD4_CTX *);
WARNING: space prohibited between function name and open parenthesis '('
+void MD4Update (MD4_CTX *, u8 *, UINT);
WARNING: space prohibited between function name and open parenthesis '('
+void MD4Final (u8 [16], MD4_CTX *);
ERROR: do not use C99 // comments
+#endif //__MD4_H__
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: trailing whitespace
+ * Copyright (C) 1998 Elmer.Joandi@ut.ee, +37-255-13500^I$
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
+#include <asm/io.h>
ERROR: do not use C99 // comments
+//#define ARLAN_DEBUGGING 1
ERROR: "foo * bar" should be "foo *bar"
+extern int arlan_command(struct net_device * dev, int command);
ERROR: trailing whitespace
+ $
ERROR: trailing whitespace
+#define IFDEBUG( L ) if ( (L) & arlan_debug ) $
ERROR: space prohibited after that open parenthesis '('
+#define IFDEBUG( L ) if ( (L) & arlan_debug )
ERROR: space prohibited before that close parenthesis ')'
+#define IFDEBUG( L ) if ( (L) & arlan_debug )
ERROR: trailing whitespace
+#define ARLAN_FAKE_HDR_LEN 12 $
ERROR: space required after that ',' (ctx:VxV)
+ #define ARLAN_DEBUG(a,b) printk(KERN_DEBUG a, b)
^
ERROR: trailing whitespace
+^I#define ARLAN_DEBUG(a,b) $
ERROR: space required after that ',' (ctx:VxV)
+ #define ARLAN_DEBUG(a,b)
^
ERROR: open brace '{' following struct go on the same line
+struct arlan_shmem
+{
ERROR: trailing whitespace
+ /* Header Signature */ $
ERROR: trailing whitespace
+ $
ERROR: trailing whitespace
+ $
ERROR: trailing whitespace
+ $
ERROR: trailing whitespace
+ $
ERROR: trailing whitespace
+ int systemId; $
ERROR: open brace '{' following struct go on the same line
+struct TxParam
+{
ERROR: "foo * bar" should be "foo *bar"
+ struct arlan_shmem __iomem * card;
ERROR: "foo * bar" should be "foo *bar"
+ struct arlan_shmem * conf;
ERROR: trailing whitespace
+ struct arlan_conf_stru * Conf;^I $
ERROR: "foo * bar" should be "foo *bar"
+ struct arlan_conf_stru * Conf;
ERROR: trailing whitespace
+ $
ERROR: space required after that ',' (ctx:VxV)
+#define READSHM(to,from,atype) {\
^
ERROR: space required after that ',' (ctx:VxV)
+#define READSHM(to,from,atype) {\
^
ERROR: space required after that ',' (ctx:VxO)
+ memcpy_fromio(&(tmp),&(from),sizeof(atype));\
^
ERROR: space required before that '&' (ctx:OxV)
+ memcpy_fromio(&(tmp),&(from),sizeof(atype));\
^
ERROR: space required after that ',' (ctx:VxV)
+ memcpy_fromio(&(tmp),&(from),sizeof(atype));\
^
ERROR: space required after that ',' (ctx:VxV)
+#define READSHMEM(from,atype)\
^
ERROR: space required after that ',' (ctx:VxV)
+#define WRITESHM(to,from,atype) \
^
ERROR: space required after that ',' (ctx:VxV)
+#define WRITESHM(to,from,atype) \
^
ERROR: space required after that ',' (ctx:VxO)
+ memcpy_toio(&(to),&tmpSHM,sizeof(atype));\
^
ERROR: space required before that '&' (ctx:OxV)
+ memcpy_toio(&(to),&tmpSHM,sizeof(atype));\
^
ERROR: space required after that ',' (ctx:VxV)
+ memcpy_toio(&(to),&tmpSHM,sizeof(atype));\
^
ERROR: space required after that ',' (ctx:VxV)
+#define DEBUGSHM(levelSHM,stringSHM,stuff,atype) \
^
ERROR: space required after that ',' (ctx:VxV)
+#define DEBUGSHM(levelSHM,stringSHM,stuff,atype) \
^
ERROR: space required after that ',' (ctx:VxV)
+#define DEBUGSHM(levelSHM,stringSHM,stuff,atype) \
^
ERROR: space required after that ',' (ctx:VxO)
+ memcpy_fromio(&tmpSHM,&(stuff),sizeof(atype));\
^
ERROR: space required before that '&' (ctx:OxV)
+ memcpy_fromio(&tmpSHM,&(stuff),sizeof(atype));\
^
ERROR: space required after that ',' (ctx:VxV)
+ memcpy_fromio(&tmpSHM,&(stuff),sizeof(atype));\
^
ERROR: space required after that ',' (ctx:VxV)
+ IFDEBUG(levelSHM) printk(stringSHM,tmpSHM);\
^
ERROR: space required after that ',' (ctx:VxO)
+ writeb(val,&(to))
^
ERROR: space required before that '&' (ctx:OxV)
+ writeb(val,&(to))
^
ERROR: space required after that ',' (ctx:VxO)
+ writew(val,&(to))
^
ERROR: space required before that '&' (ctx:OxV)
+ writew(val,&(to))
^
ERROR: space required after that ',' (ctx:VxO)
+ writel(val,&(to))
^
ERROR: space required before that '&' (ctx:OxV)
+ writel(val,&(to))
^
ERROR: space prohibited after that open parenthesis '('
+ ( ( READSHMB(((struct arlan_private *)netdev_priv(dev))->card->registrationMode) > 0) && \
ERROR: space prohibited after that open parenthesis '('
+ ( READSHMB(((struct arlan_private *)netdev_priv(dev))->card->registrationStatus) == 0) )
ERROR: space prohibited before that close parenthesis ')'
+ ( READSHMB(((struct arlan_private *)netdev_priv(dev))->card->registrationStatus) == 0) )
ERROR: code indent should use tabs where possible
+ ^IREADSHMB(((struct arlan_private *)netdev_priv(dev))->card->cntrlRegImage)$
ERROR: space required before the open brace '{'
+#define writeControlRegister(dev, v){\
ERROR: space required after that ',' (ctx:WxV)
+ WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->cntrlRegImage ,((v) &0xF) );\
^
ERROR: need consistent spacing around '&' (ctx:WxV)
+ WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->cntrlRegImage ,((v) &0xF) );\
^
ERROR: space prohibited before that close parenthesis ')'
+ WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->cntrlRegImage ,((v) &0xF) );\
ERROR: space required after that ',' (ctx:WxV)
+ WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->controlRegister ,(v) );}
^
ERROR: space required after that ';' (ctx:VxV)
+ WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->controlRegister ,(v) );}
^
ERROR: space prohibited before that close parenthesis ')'
+ WRITESHMB(((struct arlan_private *)netdev_priv(dev))->card->controlRegister ,(v) );}
WARNING: suspect code indent for conditional statements (3, 6)
+ if (cr & ARLAN_CHANNEL_ATTENTION){ \
+ writeControlRegister(dev, (cr & ~ARLAN_CHANNEL_ATTENTION));\
ERROR: space required before the open brace '{'
+ if (cr & ARLAN_CHANNEL_ATTENTION){ \
ERROR: space required after that close brace '}'
+ }else \
ERROR: space required before the open brace '{'
+#define clearChannelAttention(dev){ \
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_CHANNEL_ATTENTION);}
^
ERROR: space required after that ';' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_CHANNEL_ATTENTION);}
^
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_RESET);}
^
ERROR: space required after that ';' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_RESET);}
^
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_RESET);}
^
ERROR: space required after that ';' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_RESET);}
^
ERROR: space required before the open brace '{'
+#define setInterruptEnable(dev){\
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_INTERRUPT_ENABLE) ;}
^
ERROR: space required after that ';' (ctx:WxV)
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_INTERRUPT_ENABLE) ;}
^
ERROR: space required before the open brace '{'
+#define clearInterruptEnable(dev){\
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_INTERRUPT_ENABLE) ;}
^
ERROR: space required after that ';' (ctx:WxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_INTERRUPT_ENABLE) ;}
^
ERROR: space required before the open brace '{'
+#define setClearInterrupt(dev){\
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_CLEAR_INTERRUPT) ;}
^
ERROR: space required after that ';' (ctx:WxV)
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_CLEAR_INTERRUPT) ;}
^
ERROR: space required before the open brace '{'
+#define clearClearInterrupt(dev){\
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_CLEAR_INTERRUPT);}
^
ERROR: space required after that ';' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_CLEAR_INTERRUPT);}
^
ERROR: space required before the open brace '{'
+#define setPowerOff(dev){\
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) | (ARLAN_POWER && ARLAN_ACCESS));\
^
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_ACCESS);}
^
ERROR: space required after that ';' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_ACCESS);}
^
ERROR: space required before the open brace '{'
+#define setPowerOn(dev){\
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~(ARLAN_POWER)); }
^
ERROR: space required before the open brace '{'
+#define arlan_lock_card_access(dev){\
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_ACCESS);}
^
ERROR: space required after that ';' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) & ~ARLAN_ACCESS);}
^
ERROR: space required before the open brace '{'
+#define arlan_unlock_card_access(dev){\
ERROR: trailing whitespace
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_ACCESS ); } $
ERROR: space required after that ',' (ctx:VxV)
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_ACCESS ); }
^
ERROR: space prohibited before that close parenthesis ')'
+ writeControlRegister(dev,readControlRegister(dev) | ARLAN_ACCESS ); }
ERROR: trailing whitespace
+ $
ERROR: trailing whitespace
+ $
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: code indent should use tabs where possible
+ 0 = [-10,10]$
ERROR: code indent should use tabs where possible
+ 0 = [-10,10]$
WARNING: braces {} are not necessary for single statement blocks
+ if (stat & (DT_S_COMPOSITE_ERROR | DT_S_READY)) {
+ return stat;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (stat & DT_S_COMPOSITE_ERROR) {
+ return stat;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (stat & DT_S_READY) {
+ return 0;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (stat & DT_S_COMPOSITE_ERROR) {
+ return stat;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (stat & DT_S_READY) {
+ return 0;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (!(stat & DT_S_READY)) {
+ printk("dt2801: !ready in dt2801_writecmd(), ignoring\n");
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (!timeout) {
+ printk("dt2801: timeout 1 status=0x%02x\n", stat);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (!timeout) {
+ printk("dt2801: timeout 2 status=0x%02x\n", stat);
+ }
WARNING: braces {} are not necessary for any arm of this statement
+ if (stat == -ETIME) {
[...]
+ } else {
[...]
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for any arm of this statement
+ if (data[0] == COMEDI_OUTPUT) {
[...]
+ } else {
[...]
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for single statement blocks
+ if (fifo_empty) {
+ break;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (irq) {
+ printk(", irq %u", irq);
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: Macros with complex values should be enclosed in parenthesis
+#define N_WORDS 3000*64
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: do not initialise statics to 0 or NULL
+static unsigned int ui_Temp = 0;
WARNING: braces {} are not necessary for any arm of this statement
+ if (data[1]) {
[...]
+ } else
[...]
WARNING: braces {} are not necessary for single statement blocks
+ for (i = 0; i < devpriv->ui_AiNbrofChannels; i++) {
+ devpriv->ui_AiChannelList[i] = data[4 + i];
+ }
ERROR: that open brace { should be on the previous line
+ } else /* EOC */
+ {
WARNING: braces {} are not necessary for any arm of this statement
+ if (data[1]) {
[...]
+ } else {
[...]
ERROR: that open brace { should be on the previous line
+ if (insn->unused[0] == 222) /* second insn read */
+ {
WARNING: braces {} are not necessary for single statement blocks
+ for (i = 0; i < insn->n; i++) {
+ data[i] = devpriv->ui_AiReadData[i];
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (cmd->start_src != TRIG_NOW && cmd->start_src != TRIG_EXT) {
+ err++;
+ }
ERROR: that open brace { should be on the previous line
+ if (cmd->scan_begin_src == TRIG_TIMER) /* Test Delay timing */
+ {
ERROR: that open brace { should be on the previous line
+ if (cmd->convert_src == TRIG_TIMER) /* Test Acquisition timing */
+ {
WARNING: braces {} are not necessary for any arm of this statement
+ if (cmd->stop_src == TRIG_COUNT) {
[...]
+ } else {
[...]
WARNING: braces {} are not necessary for single statement blocks
+ if (devpriv->b_ExttrigEnable == APCI3120_ENABLE) {
+ i_APCI3120_ExttrigEnable(dev); /* activate EXT trigger */
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (dmalen0 > (devpriv->ui_AiDataLength)) {
+ dmalen0 = devpriv->ui_AiDataLength;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (dmalen1 > (devpriv->ui_AiDataLength)) {
+ dmalen1 = devpriv->ui_AiDataLength;
+ }
WARNING: braces {} are not necessary for any arm of this statement
+ if (CR_RANGE(chanlist[i]) < APCI3120_BIPOLAR_RANGES) {
[...]
+ } else {
[...]
ERROR: that open brace { should be on the previous line
+ if (devpriv->b_EocEosInterrupt == APCI3120_ENABLE) /* enable this in without DMA ??? */
+ {
ERROR: that open brace { should be on the previous line
+ if (data[0] == APCI3120_TIMER) /* initialize timer */
+ {
ERROR: that open brace { should be on the previous line
+ } else /* Initialize Watch dog */
+ {
ERROR: that open brace { should be on the previous line
+ if (data[0] == 2) /* write new value */
+ {
ERROR: that open brace { should be on the previous line
+ if (devpriv->b_Timer2Mode == APCI3120_TIMER) /* start timer */
+ {
ERROR: that open brace { should be on the previous line
+ } else /* start watch dog */
+ {
ERROR: that open brace { should be on the previous line
+ if (devpriv->b_Timer2Mode == APCI3120_TIMER) /* start timer */
+ {
ERROR: that open brace { should be on the previous line
+ } else /* Read watch dog status */
+ {
WARNING: braces {} are not necessary for single statement blocks
+ if (!devpriv->b_OutputMemoryStatus) {
+ ui_Temp = 0;
+
+ } /* if(!devpriv->b_OutputMemoryStatus ) */
ERROR: code indent should use tabs where possible
+ data[0] Value to be written$
ERROR: code indent should use tabs where possible
+ data[1] :1 Set digital o/p ON$
ERROR: code indent should use tabs where possible
+ data[1] 2 Set digital o/p OFF with memory ON$
ERROR: that open brace { should be on the previous line
+ if (ui_Range) /* if 1 then unipolar */
+ {
ERROR: that open brace { should be on the previous line
+ } else /* if 0 then bipolar */
+ {
ERROR: that open brace { should be on the previous line
+ do /* Waiting of DA_READY BIT */
+ {
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: code indent should use tabs where possible
+ NONE$
ERROR: do not initialise statics to 0 or NULL
+static struct pcmcia_device *cur_dev = NULL;
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for single statement blocks
+ if (dev->iobase) {
+ comedi_pci_disable(devpriv->pci_dev);
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for any arm of this statement
+ if (it->options[2]) {
[...]
+ } else {
[...]
WARNING: braces {} are not necessary for single statement blocks
+ if (devpriv->registers) {
+ comedi_pci_disable(devpriv->pci_dev);
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for any arm of this statement
+ if (thisboard->has_dio) {
[...]
+ } else {
[...]
WARNING: braces {} are not necessary for single statement blocks
+ if (devpriv->BADR0) {
+ comedi_pci_disable(devpriv->pci_dev);
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for single statement blocks
+ if (devpriv->dio_reg_base) {
+ comedi_pci_disable(devpriv->pci_dev);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ for (i = 0; i < thisboard->n_8255; i++) {
+ subdev_8255_cleanup(dev, dev->subdevices + i);
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for single statement blocks
+ if (devpriv->dac) {
+ comedi_pci_disable(devpriv->pci_dev);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (inw_p(devpriv->dac + DACALIBRATION1) & SERIAL_OUT_BIT) {
+ value |= 1 << (value_width - i);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ for (i = 0; i < max_num_caldacs; i++) {
+ cal2_bits |= DESELECT_CALDAC_BIT(i);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ for (i = 0; i < max_num_caldacs; i++) {
+ cal2_bits |= DESELECT_CALDAC_BIT(i);
+ }
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: "foo * bar" should be "foo *bar"
+ uint8_t * data);
WARNING: braces {} are not necessary for single statement blocks
+ if (devpriv->s5933_config) {
+ comedi_pci_disable(devpriv->pci_dev);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (cmd->stop_src == TRIG_COUNT) {
+ devpriv->count = cmd->chanlist_len * cmd->stop_arg;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (cmd->stop_src == TRIG_COUNT) {
+ devpriv->ao_count = cmd->chanlist_len * cmd->stop_arg;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (cmd->stop_src == TRIG_COUNT) {
+ devpriv->ao_count -= num_points;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (dev->attached == 0) {
+ return IRQ_NONE;
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if ((status & (INT | EOAI | LADFUL | DAHFI | DAEMI)) == 0) {
+ comedi_error(dev, "spurious interrupt");
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (status & (DAHFI | DAEMI)) {
+ handle_ao_interrupt(dev, status);
+ }
WARNING: braces {} are not necessary for single statement blocks
+ if (async->cmd.stop_src == TRIG_COUNT) {
+ devpriv->ao_count -= num_points;
+ }
ERROR: "foo * bar" should be "foo *bar"
+ uint8_t * data)
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: do not initialise externals to 0 or NULL
+unsigned int ui_InterruptStatus = 0;
WARNING: braces {} are not necessary for single statement blocks
+ else {
+ outl(0x6, devpriv->iobase + APCI1032_DIGITAL_IP_IRQ);
+ } /* else if(data[1] == ADDIDATA_OR) */
WARNING: braces {} are not necessary for single statement blocks
+ if (data[1] == 1) {
+ *data = ui_InterruptStatus;
+ } /* if(data[1]==1) */
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: code indent should use tabs where possible
+ const struct comedi_lrange *pr_AiRangelist;^I/* rangelist for A/D */$
ERROR: code indent should use tabs where possible
+ const struct comedi_lrange *pr_AoRangelist;^I/* rangelist for D/A */$
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: braces {} are not necessary for any arm of this statement
+ if (i_Counter == 0) {
[...]
+ } else {
[...]
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL isn't anymore present into these files thus it is no necessary still include smp_lock.h.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
according to 'linux device drivers',
ENOENT, ECONNRESET, ESHUTDOWN are not real transmission errors.
also, a little cosmetics.
Signed-off-by: Florian Schilhabel <florian.c.schilhabel@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because the Firmware is loaded from RTL8192SU/rtl8192sfw.bin,
it it save, to remove it from r8192SU_HWImg.c
Signed-off-by: Florian Schilhabel <florian.c.schilhabel@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes some RT-triggered compile errors and typos.
Signed-off-by: Sven-Thorsten Dietrich <sdietrich@novell.com>
Acked-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does following improvements:
1. Follow kernel style for comments
2. Reorganize code for readability improvement
3. Use PCI helper macros
4. Use __devinit, __devexit, __devexit_p at necessary places
5. Mark functions and data as static when it is not exported
Signed-off-by: Ameya Palande <2ameya@gmail.com>
Cc: Naren Sankar <nsankar@broadcom.com>
Cc: Jarod Wilson <jarod@wilsonet.com>
Cc: Scott Davilla <davilla@4pi.com>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the prism2usb.c that fixes one line which was over
the 80 character limit by wrapping it to a new line and removes a
commented out configuration for a ZyDAS ZD1201 device since support for
this device with this driver is now deprecated.
Signed-off-by: Jim Dog <jimdog@northern-indymedia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sparse warns that:
drivers/staging/pohmelfs/inode.c:1797: warning: initialization from incompatible pointer type
so fix pohmelfs_write_inode() to have the expected parameters.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix prism2fw.c printk format warning:
drivers/staging/wlan-ng/prism2fw.c:209: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The rtl8192* drivers in staging use semaphores, so they need
to #include <linux/semaphore.h>.
(similar to staging-rtl8187se-needs-semaphore.h.patch)
drivers/staging/rtl8192e/ieee80211/ieee80211.h:2038: error: field 'ips_sem' has incomplete type
drivers/staging/rtl8192e/ieee80211/ieee80211.h:2249: error: field 'wx_sem' has incomplete type
drivers/staging/rtl8192e/ieee80211/ieee80211.h:2250: error: field 'scan_sem' has incomplete type
drivers/staging/rtl8192e/ieee80211/ieee80211_softmac.c:442: error: implicit declaration of function 'down'
drivers/staging/rtl8192e/ieee80211/ieee80211_softmac.c:500: error: implicit declaration of function 'up'
drivers/staging/rtl8192e/ieee80 211/ieee80211_softmac.c:3165: error: implicit declaration of function 'sema_init'
drivers/staging/rtl8192su/ieee80211/ieee80211.h:1330: error: field 'wx_sem' has incomplete type
drivers/staging/rtl8192su/ieee80211/ieee80211.h:1331: error: field 'scan_sem' has incomplete type
drivers/staging/rtl8192u/ieee80211/ieee80211.h:2010: error: field 'wx_sem' has incomplete type
drivers/staging/rtl8192u/ieee80211/ieee80211.h:2011: error: field 'scan_sem' has incomplete type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increased timeout for digital output dma loading, due to report of it
being too short for some hardware.
Signed-off-by: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the amplc_pc236 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the amplc_dio200 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the aio_iiro_16 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_labpc.c file that fixes the brace warnings and
comments over 80 characters found by the checkpatch.pl tool. Some code
still goes over 80 characters because I didn't know what to do with it.
Signed-off-by: Stewart Robertson <stewart_r@aliencamel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that batman-adv does not process packets before its
initialization is complete. Some sanity checks added to the receiver
function.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
skb_share_check() returns NULL if it can't allocate more memory but
it still frees the skbuff.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vis code takes a copy of the data inside the skbuf if it is interesting
for us, so we always need to release the skbuf.
Reported-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the bug discovered by Marek Lindner which did not allow
turning on the vis-server before an interface has been added. With this
patch we are using a global atomic variable for activating and
deactiating the vis-server-mode, which can be used before
inserting an interface.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes a variable that became obsolete since the skb handling
replaced the packet handling thread.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The routing code has 2 sections which warn about ttl exceeded. The
corresponding warnings were identical which makes it hard to debug. In
addition, batman-adv does not need to warn about ttl exceeded in case
we encountered an echo request as this is commonly used to generate
traceroute graphs.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As in other parts of batman-adv, we should not lock while sending a packet but
keep the lock held for as short as possible. Additionally, we should check
whether the interface is active, otherwise batman_if->net_dev might not be
available ...
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code which uses the raw packet sockets was removed. The only related
dependencies are the skb and netdev handling code. This is provided by
NET in Kconfig.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Staticise a number of functions which aren't exported outside their
source files, and also add a __user annotation for the buffer in
iio_event_chrdev_read().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the ni_daq_700.c file that fixes up brace and 80 character warnings
found by the checkpatch.pl tool
Signed-off-by: Graham M Howe <gman.1352@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
VMIVME-7805 board has a special control register that has to be used in
order to activate the VME bus access via the Universe II bridge.
This control register also handles endianess convertion.
Signed-off-by: Arthur Benilov <arthur.benilov@iba-group.com>
Signed-off-by: Vincent Bossier <vincent.bossier@iba-group.com>
Acked-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For VME device I/O operations on master windows the user driver tends
to use kern_buf buffer array which is not allocated. This causes an error
when reading from master window device files.
Signed-off-by: Arthur Benilov <arthur.benilov@iba-group.com>
Signed-off-by: Vincent Bossier <vincent.bossier@iba-group.com>
Acked-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When requesting slave resources A16 addressing mode flag is used to find
available windows. Since the ca91cx42 bridge only supports two A16 slave windows
but four are requested, the driver fails to initialize. The flag has been
changed to A24, which is supported by all slave windows.
Signed-off-by: Arthur Benilov <arthur.benilov@iba-group.com>
Signed-off-by: Vincent Bossier <vincent.bossier@iba-group.com>
Acked-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the code from the drivers that we are not going to implement before
submitting for review.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for Master Read-Modify-Write cycles on the ca91cx42.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ca91cx42 driver currently incorrectly handles master windows, setting
and retrieving the sizing parameters incorrectly. Also, in the slave window
handling, it uses an incorrectly set variable.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the DMA controller in the ca91cx42 bridge.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vme_master_resource structure contains an item called "pci_resource".
Rename to make bus agnostic.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At the moment the vme bridge drivers are written in a way that only
allows them to support one bridge at a time. Modify the drivers to
enable more than one bridge to be present per board.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check the directions in which the DMA controller is expected to operate
before giving control of a resource.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects author email addresses and Copyright notices as a
result of the split up of the GE Fanuc joint venture.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rtl8187se needs to include semaphore.h to prevent build errors:
drivers/staging/rtl8187se/ieee80211/ieee80211.h:1004: error: field 'wx_sem' has incomplete type
drivers/staging/rtl8187se/ieee80211/ieee80211.h:1005: error: field 'scan_sem' has incomplete type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Specify Kconfig dependencies, and include warnings for building as a module
udlfb is dependent on FB_DEFERRED_IO, FB_SYS_*, and FB_MODE_HELPERS
Because many kernels do not include defio (which cannot be built
as a module), yet users want to be able to build udlfb as a module later,
udlfb has ifdefs and these dependency warnings to help udlfb build with or
without certain dependencies, but also print warnings for any lost function.
Even though this kind of flexibility isn't common, we've gotten feedback
from a significant portion of users that they were frustrated without it.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for fbdev mmap clients who don't send damage ioctls
Because DisplayLink devices are out on the other end of usb, their
"framebuffer" is just normal system memory. So memory mapped writes
don't automatically trigger anything. So up to this point, standard
fbdev clients who rely on mmap() will get an unchanging screen.
This patch makes udlfb a client of Jaya Kumar's defio framework - which sets
up page fault triggers, and those faults are accumulated and sent to udlfb
on a defferred basis, to process as damage notifications for the framebuffer.
Because this involves more overhead than a notification directly from
the application (e.g. just passing on X DAMAGE extension notifications),
a sysfs attribute is provided by udlfb to control defio support.
/sys/class/graphics/fb*/use_defio - writing a "0" to this file before
calling mmap() causes defio to not be initialized - instead udlfb
will rely on getting damage notifications directly through the damage ioctl.
There are unsolved rendering problems with defio (horizontal dead regions
on framebuffer, that accumulate over time) which still needs a fix.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework rendering for improved performance
Approx 10-20% gain avg across several "benchmarks": x11perf, gtkperf, glxgears
Moves from a single pre-alloc'd urb protected by a long-held mutex
To a list of (4) pre-alloc'd urbs which can be dispatched asynchonously
Improved rendering algorithm to hardware with lower CPU consumption,
fewer system memory accesses, and slightly higher compression.
Better scalability to multiple processors, especially with
multiple framebuffers active.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework probe to use refcounts and std functions
Because the different parts of the driver (usb, fbdev) tear down
in different orders, the driver previously could crash accessing
data that had already been freed. Refcounting system used to handle.
Reworked probe to make use of refcounts, set mode using std fbops,
and set up sysfs and pre-allocated urbs.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add sysfs controls for edid and performance metrics
There are 8 new files exposed in /sys/class/graphics/fb*
edid - returns 128 byte edid blog, suitable for parsing with parse-edid
metrics_bytes_identical
metrics_bytes_rendered
metrics_bytes_sent
metrics_cpu_kcycles_used
metrics_misc
and metrics_reset, which resets all perf metrics to zero
The 6 perf metrics are of type atomic_t.
So these metrics return precise results for short benchmarks, but
any test approx a minute or longer runtime may roll over.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move to more consistent naming scheme
All udlfb functions start with udlfb_
All functions for udlfb's fbdev interface start with udlfb_ops_
All functinos for udlfb's usb interface start with udlfb_usb_
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add functions to pre-allocate and free usb bulk urbs for core render path.
Udlfb currently allocates a single urb, guarded by a mutex, that is a key
bottleneck. Because udlfb sends so much data, preallocation is most efficient.
Functions will be used by new rendering functions in later patches.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reorganize the location of a few things to be closer to related code
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eliminate checkpatch.pl warnings and errors so later patches in series are clean
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the RTL8187SE, the variable priv->rf_chip is always RF_ZEBRA4
and priv->RegThreeWireMode is always HW_THREE_WIRE_SI. Remove these
2 variables.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanups as suggested by checkpatch.pl utiltiy.
.o's from before and after cleanup have matching SHA1s.
Signed-off-by: Svenne Krap <svenne@krap.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to ni_atmio.c file to fix up bracing style problems
found by checkpatch.pl tool
Signed-off-by: Graham M Howe <gman.1352@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's clear from the indent levels and the context that there are supposed to
be curly braces here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current driver does not follow the state of the RF switch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TODO list includes switching this driver to use the common EEPROM
routines in EEPROM_93CX.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested by: Bernhard Schiffner <bernhard@schiffner-limbach.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed parenthesis from return statements,
split up assignment and if condition
Signed-off-by: Jochen Maes <jochen.maes@sejo.be>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the rti800 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add suspend and resume functions (which are currently stubs
returning -ENOSYS)
Signed-off-by: Mark Allyn <mark.a.allyn@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provides a better explanation of what this
driver is for in the Kconfig file
Signed-off-by: Mark Allyn <mark.a.allyn@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renames the directory in which the driver files
are located; again for clarity.
Signed-off-by: Mark Allyn <mark.a.allyn@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch renames rar_driver to rar_register to clarifiy and differentiate
from rar_handler that will be submitted later
Signed-off-by: Mark Allyn <mark.a.allyn@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that Mimio has a userspace solution for this product using
libusb, and the in-kernel driver is just getting in the way now and
causing problems. So they have asked that the in-kernel driver be
removed. As the staging driver wasn't quite working anyway, and Mimio
supports their libusb solution for all distros, I am removing the
in-kernel driver.
The libusb solution can be downloaded from:
http://www.mimio.com/downloads/mimio_studio_software/linux.asp
Cc: <mwilder@cs.nmsu.edu>
Cc: Phil Hannent <phil@hannent.co.uk>
Cc: Marc Rousseau <Marc.Rousseau@mimio.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes up the sparse and coding style issues found in the
dt3155_io.c file.
No code is changed, only formatting and removing unused code.
Cc: Scott Smedley <ss@aao.gov.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes almost all checkpatch issues in the ni_pcidio comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the rti802 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the dt2815 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the r8180_93cx6.c file that fixes up spacing issue
warnings found by the checkpatch.pl tool
Signed-off-by: Tim Schofield <tim@weberpafrica.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch to the comedi_fops.c file fixes a brace warning found by the checkpatch.pl tool
Signed-off-by: Paul Elms <paul@uprocera.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes all of the brace style warnings found by the
checkpatch.pl tool
Signed-off-by: Tony Burrows <tony@tonyburrows.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove iw_handle_def private initialisations as they are no longer need
these.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
String constants that are continued on subsequent lines with \
are not good.
Fixed a "is tryied" / tried typo
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the adq12b comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the fl512 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the ni_65xx comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the ni_670x comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the ni_660x comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the poc comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the pcm3730 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes all checkpatch issues in the pcm3724 comedi driver.
Signed-off-by: Benjamin Adolphi <b.adolphi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, we crash (issue BUG_ON) if backing swap
disk size is zero. This can happen is user specified
an extended partition or simply a bad disk as backing
swap. A crash is really an unpleasant surprise to user
for such trivial problems.
Now, we check for this condition and simply fail device
initialization if this is the case.
Additional cleanups:
* use static for all functions
* remove extra newline between functions
* memset backing_swap_name to NULL on device reset
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ramzswap_free_page() already handles the case for zero filled
pages. So, remove redundant logic for the same in ramzswap_write().
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, we return 0 if create_device() fails and 1 otherwise.
Now, proper error code is returned from create_device() and the
same is propagated as module error code from ramzswap_init().
Also added some cleanups for ramzswap_init(), improving function
structure.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ramzswap block size needs to be set equal to PAGE_SIZE to
avoid receiving any unaligned block I/O requests (happens
due to readahead logic during swapon). These unaligned
accesses produce unnecessary I/O errors, scaring users.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we flush block device before freeing all metadata
during reset ioctl.
Signed-off-by: Nitin Gupta <ngupta@vflar.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
64-bit stats corruption was observed when ramzswap was
used on SMP systems. To prevent this, use separate spinlock
to protect these stats.
Also, replace stat_*() with rzs_stat*() to avoid possible
conflict with core kernel code.
Eventually, these will be converted to per-cpu counters
if this driver finds use on large scale systems and this
locking is found to affect scalability.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup the driver and fix a faulty if statement.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested by: Bernhard Schiffner <bernhard@schiffner-limbach.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the dead uncompiled code in usbip_common.c
Signed-off-by: Himanshu Chauhan <himanshu@symmetricore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This completes the structures within the txmac block so we can now
propogate a name change and type removal up a layer and clean up TXMAC as
well
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is another one we don't really need to do much to get rid of
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only used for one trivial thing so turn that into something trivial instead
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have lots of tiny files right now that could be one
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This completes the typedef clean up of the rx specific structures, although
there is plenty do on field names and the like
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the subtypes are sane so just turn it into something struct and linux
like
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the proper pointer types for the higher level pointers to the rx_status
object and kill casts
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So kill off the top level type and turn it into a struct
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the contents of this type are now clean, so kill the top level type
as well
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The contents of MMC_t are clean so kill off the MMC_t typedef
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the contents are clean so kill off the top level typedefs
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have a clean struct of this now so turn the top level typedefs into a
struct
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is another set of flags as typedef that can be cleaned up.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up the typdef for fbr_desc itself so we know it is done
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is only used meaningfully as a definition, we never mask and fetch the
bits apart
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is another 10 bit value with the high bits clear, and where the
type doesn't get used anywhere properly anyway
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add necessary include to fix build on PowerPC
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I removed a misplace semicolon. It is clear from the indentation that
TxPwrTracking87SE() was only supposed to be called if CheckTxPwrTracking()
returned true.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When originally introduced into staging, these drivers had custom
firmware-loading code which checked a version number and CRC at the
end of each blob. This reintroduces those checks, using crc-ccitt
instead of custom code.
The removed firmware will be added to the linux-firmware.git
repository.
Based on work by Darren Salt <linux@youmustbejoking.demon.co.uk>.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-By: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These functions do not modify the data they are passed.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Regardless of the condition, the branches executed the same code
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Regardless of the condition, the branches execute the same code
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For AI command testing, the driver does not need to range-check the
length of the channel list as the comedi core has already checked it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check the channel list is valid in step 5 of the AI command test.
Split function check_and_setup_channel_list() in two. Also, remove
unnecessary chanlist_len tests in step 3 of the AI command test as the
comedi core has already checked it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For multi-channel AI commands, the interrupt handler is missing code to
switch to the next channel. Add some (untested) code to handle this.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hendrik Brueckner
Wim Van Sebroeck
Paul Mundt
Randy Dunlap
Lee, Chun-Yi
Greg Kroah-Hartman
Stephen Rothwell
Eric W. Biederman
Johannes Berg
Ben Hutchings
Hans J. Koch
John Ogness
Uwe Kleine-König
Emese Revfy
Luis R. Rodriguez
Kay Sievers
Andi Kleen
Dmitry Torokhov
Tejun Heo
Linus Torvalds
Florian Fainelli
Petko Manolov
Dan Carpenter
Figo.zhang
Mark Brown
Ben Dooks
Richard Röjfors
Cory Maccarrone
Luotao Fu
Wolfgang Grandegger
srinidhi kasagar
Peter Huewe
Samuel Ortiz
Denis Turischev
Mike Turquette
Magnus Damm
Yusuke Goda
Guennadi Liakhovetski
Balaji T K
Moiz Sonasath
Eduardo Valentin
Haojian Zhuang
Joonyoung Shim
Christoph Egger
Linus Walleij
Julia Lawall
H Hartley Sweeten
Andrew Morton
Krishna Gudipati
Frans Pop
Rafael J. Wysocki
Ben Gardner
Marc Zyngier
Eric Miao
Wolfram Sang
James Hogan
Aaro Koskinen
Tobias Klauser
Alexander Beregalov
Thiago Farina
Amerigo Wang
José Miguel Gonçalves
Joe Perches
Vasily Khoruzhick
Nicolas Ferre
Wolfgang Muees
Lars-Peter Clausen
Daniel Drake
Nicolas Pitre
Chris Ball
Bing Zhao
Cliff Cai
Mike Frysinger
Vipin Bhandari
Maxim Levitsky
Don Mullis
Simon Kagstrom
Thadeu Lima de Souza Cascardo
Richard Kennedy
Akinobu Mita
David Miller
Martyn Welch
Naga Chumbalkar
Mika Westerberg
Takahiro Yasui
Mike Snitzer
Peter Rajnoha
Mikulas Patocka
Nikanth Karthikesan
Kiyoshi Ueda
Moger, Babu
Breno Leitao
Jesse Brandeburg
David Dillow
David Brown
Jean Delvare
George Joseph
Sven Anders
Ping Cheng
Christoph Hellwig
Chihau Chau
Andrew Elwell
Andrea Gelmini
Stewart Robertson
Maurice Dawson
Maurice Dawson
Alessandro Ghedini
Graham M Howe
Benjamin Adolphi
Jiri Pirko
Divy Le Ray
Anton Vorontsov
Amit Shah
Dan Williams
d binderman
Alessio Igor Bogani
Florian Schilhabel
Sven-Thorsten Dietrich
Ameya Palande
Jim Dog
Sylvain Trias
Frank Mori Hess
OGAWA Hirofumi
Marek Lindner
Andrew Lunn
Linus Luessing
Simon Wunderlich
Sven Eckelmann
Arthur Benilov
Martyn Welch
Bernie Thompson
Larry Finger
Svenne Krap
Jochen Maes
Mark Allyn
Yong Zhang
Tim Schofield
Paul Elms
tony burrows
Nitin Gupta
Himanshu
Alan Cox
Dave Airlie
Roel Kluin
Ian Abbott