Eventually, we'll want to wire cephfs up to use the change attribute
that the cluster tracks instead, but for now this is unneeded.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Ideally CEPH_CAP_FILE_SHARED should have been revoked before
postive dentry get dropped. But if something goes wrong, later
cached readdir may dereference the dropped dentry.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
file locks are tracked by inode's auth mds. dropping auth caps
is equivalent to releasing all file locks.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible that we create a cap snap while there is pending
vmtruncate (truncate hasn't been processed by worker thread).
We should truncate dirty pages beyond capsnap->size in that case.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written ...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In LSSNAP case, req->r_dentry is already set to snapdir dentry.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Current code does not update ceph_dentry_info::lease_session once
it is set. If auth mds of corresponding dentry changes, dentry lease
keeps in an invalid state.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The old 'approaching max_size' code expects MDS set max_size to
'2 * reported_size'. This is no longer true. The new code reports
file size when half of previous max_size increment has been used.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Current __ceph_setattr() can set inode's i_ctime to current_time(),
req->r_stamp or attr->ia_ctime. These time stamps may have minor
differences. It may cause potential problem.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Current cephfs client uses string to indicate start position of
readdir. The string is last entry of previous readdir reply.
This approach does not work for seeky readdir because we can
not easily convert the new postion to a string. For seeky readdir,
mds needs to return dentries from the beginning. Client keeps
retrying if the reply does not contain the dentry it wants.
In current version of ceph, mds sorts CDentry in its cache in
hash order. Client also uses dentry hash to compose dir postion.
For seeky readdir, if client passes the hash part of dir postion
to mds. mds can avoid replying useless dentries.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph_set_acl() calls __ceph_setattr() if the setacl operation needs
to modify inode's i_mode. __ceph_setattr() updates inode's i_mode,
then calls posix_acl_chmod().
The problem is that __ceph_setattr() calls posix_acl_chmod() before
sending the setattr request. The get_acl() call in posix_acl_chmod()
can trigger a getxattr request. The reply of the getxattr request
can restore inode's i_mode to its old value. The set_acl() call in
posix_acl_chmod() sees old value of inode's i_mode, so it calls
__ceph_setattr() again.
Cc: stable@vger.kernel.org # needs backporting for < 4.9
Link: http://tracker.ceph.com/issues/19688
Reported-by: Jerry Lee <leisurelysw24@gmail.com>
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Luis Henriques <lhenriques@suse.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Add a system call to make extended file information available, including
file creation and some attribute flags where available through the
underlying filesystem.
The getattr inode operation is altered to take two additional arguments: a
u32 request_mask and an unsigned int flags that indicate the
synchronisation mode. This change is propagated to the vfs_getattr*()
function.
Functions like vfs_stat() are now inline wrappers around new functions
vfs_statx() and vfs_statx_fd() to reduce stack usage.
========
OVERVIEW
========
The idea was initially proposed as a set of xattrs that could be retrieved
with getxattr(), but the general preference proved to be for a new syscall
with an extended stat structure.
A number of requests were gathered for features to be included. The
following have been included:
(1) Make the fields a consistent size on all arches and make them large.
(2) Spare space, request flags and information flags are provided for
future expansion.
(3) Better support for the y2038 problem [Arnd Bergmann] (tv_sec is an
__s64).
(4) Creation time: The SMB protocol carries the creation time, which could
be exported by Samba, which will in turn help CIFS make use of
FS-Cache as that can be used for coherency data (stx_btime).
This is also specified in NFSv4 as a recommended attribute and could
be exported by NFSD [Steve French].
(5) Lightweight stat: Ask for just those details of interest, and allow a
netfs (such as NFS) to approximate anything not of interest, possibly
without going to the server [Trond Myklebust, Ulrich Drepper, Andreas
Dilger] (AT_STATX_DONT_SYNC).
(6) Heavyweight stat: Force a netfs to go to the server, even if it thinks
its cached attributes are up to date [Trond Myklebust]
(AT_STATX_FORCE_SYNC).
And the following have been left out for future extension:
(7) Data version number: Could be used by userspace NFS servers [Aneesh
Kumar].
Can also be used to modify fill_post_wcc() in NFSD which retrieves
i_version directly, but has just called vfs_getattr(). It could get
it from the kstat struct if it used vfs_xgetattr() instead.
(There's disagreement on the exact semantics of a single field, since
not all filesystems do this the same way).
(8) BSD stat compatibility: Including more fields from the BSD stat such
as creation time (st_btime) and inode generation number (st_gen)
[Jeremy Allison, Bernd Schubert].
(9) Inode generation number: Useful for FUSE and userspace NFS servers
[Bernd Schubert].
(This was asked for but later deemed unnecessary with the
open-by-handle capability available and caused disagreement as to
whether it's a security hole or not).
(10) Extra coherency data may be useful in making backups [Andreas Dilger].
(No particular data were offered, but things like last backup
timestamp, the data version number and the DOS archive bit would come
into this category).
(11) Allow the filesystem to indicate what it can/cannot provide: A
filesystem can now say it doesn't support a standard stat feature if
that isn't available, so if, for instance, inode numbers or UIDs don't
exist or are fabricated locally...
(This requires a separate system call - I have an fsinfo() call idea
for this).
(12) Store a 16-byte volume ID in the superblock that can be returned in
struct xstat [Steve French].
(Deferred to fsinfo).
(13) Include granularity fields in the time data to indicate the
granularity of each of the times (NFSv4 time_delta) [Steve French].
(Deferred to fsinfo).
(14) FS_IOC_GETFLAGS value. These could be translated to BSD's st_flags.
Note that the Linux IOC flags are a mess and filesystems such as Ext4
define flags that aren't in linux/fs.h, so translation in the kernel
may be a necessity (or, possibly, we provide the filesystem type too).
(Some attributes are made available in stx_attributes, but the general
feeling was that the IOC flags were to ext[234]-specific and shouldn't
be exposed through statx this way).
(15) Mask of features available on file (eg: ACLs, seclabel) [Brad Boyer,
Michael Kerrisk].
(Deferred, probably to fsinfo. Finding out if there's an ACL or
seclabal might require extra filesystem operations).
(16) Femtosecond-resolution timestamps [Dave Chinner].
(A __reserved field has been left in the statx_timestamp struct for
this - if there proves to be a need).
(17) A set multiple attributes syscall to go with this.
===============
NEW SYSTEM CALL
===============
The new system call is:
int ret = statx(int dfd,
const char *filename,
unsigned int flags,
unsigned int mask,
struct statx *buffer);
The dfd, filename and flags parameters indicate the file to query, in a
similar way to fstatat(). There is no equivalent of lstat() as that can be
emulated with statx() by passing AT_SYMLINK_NOFOLLOW in flags. There is
also no equivalent of fstat() as that can be emulated by passing a NULL
filename to statx() with the fd of interest in dfd.
Whether or not statx() synchronises the attributes with the backing store
can be controlled by OR'ing a value into the flags argument (this typically
only affects network filesystems):
(1) AT_STATX_SYNC_AS_STAT tells statx() to behave as stat() does in this
respect.
(2) AT_STATX_FORCE_SYNC will require a network filesystem to synchronise
its attributes with the server - which might require data writeback to
occur to get the timestamps correct.
(3) AT_STATX_DONT_SYNC will suppress synchronisation with the server in a
network filesystem. The resulting values should be considered
approximate.
mask is a bitmask indicating the fields in struct statx that are of
interest to the caller. The user should set this to STATX_BASIC_STATS to
get the basic set returned by stat(). It should be noted that asking for
more information may entail extra I/O operations.
buffer points to the destination for the data. This must be 256 bytes in
size.
======================
MAIN ATTRIBUTES RECORD
======================
The following structures are defined in which to return the main attribute
set:
struct statx_timestamp {
__s64 tv_sec;
__s32 tv_nsec;
__s32 __reserved;
};
struct statx {
__u32 stx_mask;
__u32 stx_blksize;
__u64 stx_attributes;
__u32 stx_nlink;
__u32 stx_uid;
__u32 stx_gid;
__u16 stx_mode;
__u16 __spare0[1];
__u64 stx_ino;
__u64 stx_size;
__u64 stx_blocks;
__u64 __spare1[1];
struct statx_timestamp stx_atime;
struct statx_timestamp stx_btime;
struct statx_timestamp stx_ctime;
struct statx_timestamp stx_mtime;
__u32 stx_rdev_major;
__u32 stx_rdev_minor;
__u32 stx_dev_major;
__u32 stx_dev_minor;
__u64 __spare2[14];
};
The defined bits in request_mask and stx_mask are:
STATX_TYPE Want/got stx_mode & S_IFMT
STATX_MODE Want/got stx_mode & ~S_IFMT
STATX_NLINK Want/got stx_nlink
STATX_UID Want/got stx_uid
STATX_GID Want/got stx_gid
STATX_ATIME Want/got stx_atime{,_ns}
STATX_MTIME Want/got stx_mtime{,_ns}
STATX_CTIME Want/got stx_ctime{,_ns}
STATX_INO Want/got stx_ino
STATX_SIZE Want/got stx_size
STATX_BLOCKS Want/got stx_blocks
STATX_BASIC_STATS [The stuff in the normal stat struct]
STATX_BTIME Want/got stx_btime{,_ns}
STATX_ALL [All currently available stuff]
stx_btime is the file creation time, stx_mask is a bitmask indicating the
data provided and __spares*[] are where as-yet undefined fields can be
placed.
Time fields are structures with separate seconds and nanoseconds fields
plus a reserved field in case we want to add even finer resolution. Note
that times will be negative if before 1970; in such a case, the nanosecond
fields will also be negative if not zero.
The bits defined in the stx_attributes field convey information about a
file, how it is accessed, where it is and what it does. The following
attributes map to FS_*_FL flags and are the same numerical value:
STATX_ATTR_COMPRESSED File is compressed by the fs
STATX_ATTR_IMMUTABLE File is marked immutable
STATX_ATTR_APPEND File is append-only
STATX_ATTR_NODUMP File is not to be dumped
STATX_ATTR_ENCRYPTED File requires key to decrypt in fs
Within the kernel, the supported flags are listed by:
KSTAT_ATTR_FS_IOC_FLAGS
[Are any other IOC flags of sufficient general interest to be exposed
through this interface?]
New flags include:
STATX_ATTR_AUTOMOUNT Object is an automount trigger
These are for the use of GUI tools that might want to mark files specially,
depending on what they are.
Fields in struct statx come in a number of classes:
(0) stx_dev_*, stx_blksize.
These are local system information and are always available.
(1) stx_mode, stx_nlinks, stx_uid, stx_gid, stx_[amc]time, stx_ino,
stx_size, stx_blocks.
These will be returned whether the caller asks for them or not. The
corresponding bits in stx_mask will be set to indicate whether they
actually have valid values.
If the caller didn't ask for them, then they may be approximated. For
example, NFS won't waste any time updating them from the server,
unless as a byproduct of updating something requested.
If the values don't actually exist for the underlying object (such as
UID or GID on a DOS file), then the bit won't be set in the stx_mask,
even if the caller asked for the value. In such a case, the returned
value will be a fabrication.
Note that there are instances where the type might not be valid, for
instance Windows reparse points.
(2) stx_rdev_*.
This will be set only if stx_mode indicates we're looking at a
blockdev or a chardev, otherwise will be 0.
(3) stx_btime.
Similar to (1), except this will be set to 0 if it doesn't exist.
=======
TESTING
=======
The following test program can be used to test the statx system call:
samples/statx/test-statx.c
Just compile and run, passing it paths to the files you want to examine.
The file is built automatically if CONFIG_SAMPLES is enabled.
Here's some example output. Firstly, an NFS directory that crosses to
another FSID. Note that the AUTOMOUNT attribute is set because transiting
this directory will cause d_automount to be invoked by the VFS.
[root@andromeda ~]# /tmp/test-statx -A /warthog/data
statx(/warthog/data) = 0
results=7ff
Size: 4096 Blocks: 8 IO Block: 1048576 directory
Device: 00:26 Inode: 1703937 Links: 125
Access: (3777/drwxrwxrwx) Uid: 0 Gid: 4041
Access: 2016-11-24 09:02:12.219699527+0000
Modify: 2016-11-17 10:44:36.225653653+0000
Change: 2016-11-17 10:44:36.225653653+0000
Attributes: 0000000000001000 (-------- -------- -------- -------- -------- -------- ---m---- --------)
Secondly, the result of automounting on that directory.
[root@andromeda ~]# /tmp/test-statx /warthog/data
statx(/warthog/data) = 0
results=7ff
Size: 4096 Blocks: 8 IO Block: 1048576 directory
Device: 00:27 Inode: 2 Links: 125
Access: (3777/drwxrwxrwx) Uid: 0 Gid: 4041
Access: 2016-11-24 09:02:12.219699527+0000
Modify: 2016-11-17 10:44:36.225653653+0000
Change: 2016-11-17 10:44:36.225653653+0000
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- ask for a commit reply instead of an ack reply in
__ceph_pool_perm_get()
- don't ask for both ack and commit replies in ceph_sync_write()
- since just only one reply is requested now, i_unsafe_writes list
will always be empty -- kill ceph_sync_write_wait() and go back to
a standard ->evict_inode()
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
We don't really require that the parent be locked in order to update the
lease on a dentry. Lease info is protected by the d_lock. In the event
that the parent is not locked in ceph_fill_trace, and we have both
parent and target info, go ahead and update the dentry lease.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In a later patch, we're going to need to allow ceph_fill_trace to
update the dentry's lease when the parent is not locked. This is
potentially racy though -- by the time we get around to processing the
trace, the parent may have already changed.
Change update_dentry_lease to take a ceph_vino pointer and use that to
ensure that the dentry's parent still matches it before updating the
lease.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This if block updates the dentry lease even in the case where
the MDS didn't grant one.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
struct ceph_mds_request has an r_locked_dir pointer, which is set to
indicate the parent inode and that its i_rwsem is locked. In some
critical places, we need to be able to indicate the parent inode to the
request handling code, even when its i_rwsem may not be locked.
Most of the code that operates on r_locked_dir doesn't require that the
i_rwsem be locked. We only really need it to handle manipulation of the
dcache. The rest (filling of the inode, updating dentry leases, etc.)
already has its own locking.
Add a new r_req_flags bit that indicates whether the parent is locked
when doing the request, and rename the pointer to "r_parent". For now,
all the places that set r_parent also set this flag, but that will
change in a later patch.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Currently, we have a bunch of bool flags in struct ceph_mds_request. We
need more flags though, but each bool takes (at least) a byte. Those
add up over time.
Merge all of the existing bools in this struct into a single unsigned
long, and use the set/test/clear_bit macros to manipulate them. These
are atomic operations, but that is required here to prevent
load/modify/store races. The existing flags are protected by different
locks, so we can't rely on them for that purpose.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Just get it from r_session since that's what's always passed in.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Keeping around commented out code is just asking for it to bitrot and
makes viewing the code under cscope more confusing. If
we really need this, then we can revert this patch and put it under a
Kconfig option.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This removes the uses of ACCESS_ONCE in favor of READ_ONCE
Signed-off-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Yan, Zheng <zyan@redhat.com>
sparse says:
fs/ceph/inode.c:308:36: warning: incorrect type in argument 1 (different base types)
fs/ceph/inode.c:308:36: expected unsigned int [unsigned] [usertype] a
fs/ceph/inode.c:308:36: got restricted __le32 [usertype] frag
fs/ceph/inode.c:308:46: warning: incorrect type in argument 2 (different base types)
fs/ceph/inode.c:308:46: expected unsigned int [unsigned] [usertype] b
fs/ceph/inode.c:308:46: got restricted __le32 [usertype] frag
We need to convert these values to host-endian before calling the
comparator.
Fixes: a407846ef7 ("ceph: don't assume frag tree splits in mds reply are sorted")
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Pull partial readlink cleanups from Miklos Szeredi.
This is the uncontroversial part of the readlink cleanup patch-set that
simplifies the default readlink handling.
Miklos and Al are still discussing the rest of the series.
* git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
vfs: make generic_readlink() static
vfs: remove ".readlink = generic_readlink" assignments
vfs: default to generic_readlink()
vfs: replace calling i_op->readlink with vfs_readlink()
proc/self: use generic_readlink
ecryptfs: use vfs_get_link()
bad_inode: add missing i_op initializers
If .readlink == NULL implies generic_readlink().
Generated by:
to_del="\.readlink.*=.*generic_readlink"
for i in `git grep -l $to_del`; do sed -i "/$to_del"/d $i; done
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Pull more vfs updates from Al Viro:
">rename2() work from Miklos + current_time() from Deepa"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Replace current_fs_time() with current_time()
fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
fs: Replace CURRENT_TIME with current_time() for inode timestamps
fs: proc: Delete inode time initializations in proc_alloc_inode()
vfs: Add current_time() api
vfs: add note about i_op->rename changes to porting
fs: rename "rename2" i_op to "rename"
vfs: remove unused i_op->rename
fs: make remaining filesystems use .rename2
libfs: support RENAME_NOREPLACE in simple_rename()
fs: support RENAME_NOREPLACE for local filesystems
ncpfs: fix unused variable warning
Pull vfs xattr updates from Al Viro:
"xattr stuff from Andreas
This completes the switch to xattr_handler ->get()/->set() from
->getxattr/->setxattr/->removexattr"
* 'work.xattr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: Remove {get,set,remove}xattr inode operations
xattr: Stop calling {get,set,remove}xattr inode operations
vfs: Check for the IOP_XATTR flag in listxattr
xattr: Add __vfs_{get,set,remove}xattr helpers
libfs: Use IOP_XATTR flag for empty directory handling
vfs: Use IOP_XATTR flag for bad-inode handling
vfs: Add IOP_XATTR inode operations flag
vfs: Move xattr_resolve_name to the front of fs/xattr.c
ecryptfs: Switch to generic xattr handlers
sockfs: Get rid of getxattr iop
sockfs: getxattr: Fail with -EOPNOTSUPP for invalid attribute names
kernfs: Switch to generic xattr handlers
hfs: Switch to generic xattr handlers
jffs2: Remove jffs2_{get,set,remove}xattr macros
xattr: Remove unnecessary NULL attribute name check
These inode operations are no longer used; remove them.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
current_fs_time() uses struct super_block* as an argument.
As per Linus's suggestion, this is changed to take struct
inode* as a parameter instead. This is because the function
is primarily meant for vfs inode timestamps.
Also the function was renamed as per Arnd's suggestion.
Change all calls to current_fs_time() to use the new
current_time() function instead. current_fs_time() will be
deleted.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
inode_change_ok() will be resposible for clearing capabilities and IMA
extended attributes and as such will need dentry. Give it as an argument
to inode_change_ok() instead of an inode. Also rename inode_change_ok()
to setattr_prepare() to better relect that it does also some
modifications in addition to checks.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
To avoid clearing of capabilities or security related extended
attributes too early, inode_change_ok() will need to take dentry instead
of inode. ceph_setattr() has the dentry easily available but
__ceph_setattr() is also called from ceph_set_acl() where dentry is not
easily available. Luckily that call path does not need inode_change_ok()
to be called anyway. So reorganize functions a bit so that
inode_change_ok() is called only from paths where dentry is available.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
* RADOS namespace support in libceph and CephFS (Zheng Yan and myself).
The stopgaps added in 4.5 to deny access to inodes in namespaces are
removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature bit is now fully
supported.
* A large rework of the MDS cap flushing code (Zheng Yan).
* Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU.
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJXoKLJAAoJEEp/3jgCEfOLDTUIAIcctpKUiNBokc95mQaXYl34
j7lPIaD0/Ur7JPt4nMdtlywYJYSVV2c+SglHztj/+fv0G4bWbLVEFRruh9SwKIci
PzttcmycIAqSn1f5gBZwyQbGuffd/F0EnBj7fFjcukt01i3s1ZQ7t4XtLGtAV0Ts
aIfFtx9SqWig57Z1OZqNgnhnOoh6IqNbic3FL5Hvdl5N5pFbBcQho6Vzoa5O1osH
URG6RmCcO4nykfSoxiivE7UZ+CImsXHkRD7rupBuIjqjZ8wvmZqQF5qxnkb9Dw2F
IkNhrHkTSIiv4EsNPLAETTnFSozrL1nEykKr2FBW+ti8nxNcav+8FgVapqLvFIw=
=gQ0/
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client
Pull Ceph updates from Ilya Dryomov:
"The highlights are:
- RADOS namespace support in libceph and CephFS (Zheng Yan and
myself). The stopgaps added in 4.5 to deny access to inodes in
namespaces are removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature
bit is now fully supported
- A large rework of the MDS cap flushing code (Zheng Yan)
- Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue"
* tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client: (34 commits)
ceph: fix symbol versioning for ceph_monc_do_statfs
ceph: Correctly return NXIO errors from ceph_llseek
ceph: Mark the file cache as unreclaimable
ceph: optimize cap flush waiting
ceph: cleanup ceph_flush_snaps()
ceph: kick cap flushes before sending other cap message
ceph: introduce an inode flag to indicates if snapflush is needed
ceph: avoid sending duplicated cap flush message
ceph: unify cap flush and snapcap flush
ceph: use list instead of rbtree to track cap flushes
ceph: update types of some local varibles
ceph: include 'follows' of pending snapflush in cap reconnect message
ceph: update cap reconnect message to version 3
ceph: mount non-default filesystem by name
libceph: fsmap.user subscription support
ceph: handle LOOKUP_RCU in ceph_d_revalidate
ceph: allow dentry_lease_is_valid to work under RCU walk
ceph: clear d_fsinfo pointer under d_lock
ceph: remove ceph_mdsc_lease_release
ceph: don't use ->d_time
...
We don't have requirement of searching cap flush by TID. In most cases,
we just need to know TID of the oldest cap flush. List is ideal for this
usage.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
This patch adds codes that decode pool namespace information in
cap message and request reply. Pool namespace is saved in i_layout,
it will be passed to libceph when doing read/write.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Add pool namesapce pointer to struct ceph_file_layout and struct
ceph_object_locator. Pool namespace is used by when mapping object
to PG, it's also used when composing OSD request.
The namespace pointer in struct ceph_file_layout is RCU protected.
So libceph can read namespace without taking lock.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
[idryomov@gmail.com: ceph_oloc_destroy(), misc minor changes]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Define new ceph_file_layout structure and rename old ceph_file_layout
to ceph_file_layout_legacy. This is preparation for adding namespace
to ceph_file_layout structure.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
We always mixed in the parent pointer into the dentry name hash, but we
did it late at lookup time. It turns out that we can simplify that
lookup-time action by salting the hash with the parent pointer early
instead of late.
A few other users of our string hashes also wanted to mix in their own
pointers into the hash, and those are updated to use the same mechanism.
Hash users that don't have any particular initial salt can just use the
NULL pointer as a no-salt.
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull Ceph updates from Sage Weil:
"This changeset has a few main parts:
- Ilya has finished a huge refactoring effort to sync up the
client-side logic in libceph with the user-space client code, which
has evolved significantly over the last couple years, with lots of
additional behaviors (e.g., how requests are handled when cluster
is full and transitions from full to non-full).
This structure of the code is more closely aligned with userspace
now such that it will be much easier to maintain going forward when
behavior changes take place. There are some locking improvements
bundled in as well.
- Zheng adds multi-filesystem support (multiple namespaces within the
same Ceph cluster)
- Zheng has changed the readdir offsets and directory enumeration so
that dentry offsets are hash-based and therefore stable across
directory fragmentation events on the MDS.
- Zheng has a smorgasbord of bug fixes across fs/ceph"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (71 commits)
ceph: fix wake_up_session_cb()
ceph: don't use truncate_pagecache() to invalidate read cache
ceph: SetPageError() for writeback pages if writepages fails
ceph: handle interrupted ceph_writepage()
ceph: make ceph_update_writeable_page() uninterruptible
libceph: make ceph_osdc_wait_request() uninterruptible
ceph: handle -EAGAIN returned by ceph_update_writeable_page()
ceph: make fault/page_mkwrite return VM_FAULT_OOM for -ENOMEM
ceph: block non-fatal signals for fault/page_mkwrite
ceph: make logical calculation functions return bool
ceph: tolerate bad i_size for symlink inode
ceph: improve fragtree change detection
ceph: keep leaf frag when updating fragtree
ceph: fix dir_auth check in ceph_fill_dirfrag()
ceph: don't assume frag tree splits in mds reply are sorted
ceph: fix inode reference leak
ceph: using hash value to compose dentry offset
ceph: don't forbid marking directory complete after forward seek
ceph: record 'offset' for each entry of readdir result
ceph: define 'end/complete' in readdir reply as bit flags
...
truncate_pagecache() drops dirty pages, it's dangerous to use it
to invalidate read cache. Besides, we shouldn't start invalidating
read cache while there are buffer writers. Because buffer writers
may add dirty pages later.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Jeff Layton
Yan, Zheng
Greg Kroah-Hartman
Markus Elfring
David Howells
Ilya Dryomov
Seraphime Kirkovski
Linus Torvalds
Al Viro
Miklos Szeredi
Andreas Gruenbacher
Deepa Dinamani
Jan Kara