Add iio map to allow power driver to read out values as a consumer.
This approach does not block later addition of devicetree support
which would be helpful if there is an in-kernel consumer for AIN0/1.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently the for-loop that scans for the optimial adc_period iterates
through all the possible adc_period levels because the exit logic in
the loop is inverted. I believe the comparison should be swapped and
the continue replaced with a break to exit the loop at the correct
point.
Addresses-Coverity: ("Continue has no effect")
Fixes: e08e19c331 ("iio:adc: add iio driver for Palmas (twl6035/7) gpadc")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210730071651.17394-1-colin.king@canonical.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The datasheets have the following note for the conversion time
specification: "This parameter is specified by design and/or
characterization and it is not tested in production."
Parts have been seen that require more time to do 14-bit conversions for
the relative humidity channel. The result is ENXIO due to the address
phase of a transfer not getting an ACK.
Delay an additional 1 ms per conversion to allow for additional margin.
Fixes: 4839367d99 ("iio: humidity: add HDC100x support")
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Link: https://lore.kernel.org/r/20210614141820.2034827-1-chris.lesiak@licor.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With CONFIG_SPI=y and CONFIG_I2C=m, building fxls8962af into vmlinux
causes a link error against the I2C module:
aarch64-linux-ld: drivers/iio/accel/fxls8962af-core.o: in function `fxls8962af_fifo_flush':
fxls8962af-core.c:(.text+0x3a0): undefined reference to `i2c_verify_client'
Work around it by adding a Kconfig dependency that forces the SPI driver
to be a loadable module whenever I2C is a module.
Fixes: af959b7b96 ("iio: accel: fxls8962af: fix errata bug E3 - I2C burst reads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721151330.2176653-1-arnd@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set reset pin direction to output as the reset pin needs to be an active
low output pin.
Co-developed-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Antti Keränen <detegr@rbx.email>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Fixes: ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
Link: https://lore.kernel.org/r/20210708095425.13295-1-detegr@rbx.email
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.
Fixes: e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of IIO and staging driver patches for 5.14-rc1.
Loads of IIO driver updates and additions in here, the shortlog has the
full details.
For the staging side, we moved a few drivers out of staging, and deleted
the kpc2000 drivers as the original developer asked us to because no one
was working on them anymore.
Also in here are loads of coding style cleanups due to different intern
projects focusing on the staging tree to try to get experience doing
kernel development.
All of these have been in the linux-next tree for a while with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM50w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZ4wCeK/JreZijlAy0O5Gq1equvRx1jJoAoJmmt7UY
bx6qpcmUM7c53cMXr/kh
=6suo
-----END PGP SIGNATURE-----
Merge tag 'staging-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big set of IIO and staging driver patches for 5.14-rc1.
Loads of IIO driver updates and additions in here, the shortlog has
the full details.
For the staging side, we moved a few drivers out of staging, and
deleted the kpc2000 drivers as the original developer asked us to
because no one was working on them anymore.
Also in here are loads of coding style cleanups due to different
intern projects focusing on the staging tree to try to get experience
doing kernel development.
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'staging-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (744 commits)
staging: hi6421-spmi-pmic: cleanup some macros
staging: hi6421-spmi-pmic: change identation of a table
staging: hi6421-spmi-pmic: change a return code
staging: hi6421-spmi-pmic: better name IRQs
staging: hi6421-spmi-pmic: use devm_request_threaded_irq()
staging: hisilicon,hi6421-spmi-pmic.yaml: cleanup descriptions
spmi: hisi-spmi-controller: move driver from staging
phy: phy-hi3670-usb3: move driver from staging into phy
staging: rtl8188eu: remove include/rtw_debug.h header
staging: rtl8188eu: remove GlobalDebugLevel variable
staging: rtl8188eu: remove DRIVER_PREFIX preprocessor definition
staging: rtl8188eu: remove RT_TRACE macro
staging: rtl8188eu: remove all RT_TRACE calls from hal/rtl8188eu_recv.c
staging: rtl8188eu: remove all RT_TRACE calls from hal/hal_intf.c
staging: rtl8188eu: remove all RT_TRACE calls from hal/rtl8188eu_xmit.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_xmit.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_pwrctrl.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_recv.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_ioctl_set.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_ieee80211.c
...
This KUnit update for Linux 5.14-rc1 consists of fixes and features:
-- add support for skipped tests
-- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
-- add gnu_printf specifiers
-- add kunit_shutdown
-- add unit test for filtering suites by names
-- convert lib/test_list_sort.c to use KUnit
-- code organization moving default config to tools/testing/kunit
-- refactor of internal parser input handling
-- cleanups and updates to documentation
-- code cleanup related to casts
-----BEGIN PGP SIGNATURE-----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=5QAv
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit update from Shuah Khan:
"Fixes and features:
- add support for skipped tests
- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
- add gnu_printf specifiers
- add kunit_shutdown
- add unit test for filtering suites by names
- convert lib/test_list_sort.c to use KUnit
- code organization moving default config to tools/testing/kunit
- refactor of internal parser input handling
- cleanups and updates to documentation
- code cleanup related to casts"
* tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
kunit: add unit test for filtering suites by names
kasan: test: make use of kunit_skip()
kunit: test: Add example tests which are always skipped
kunit: tool: Support skipped tests in kunit_tool
kunit: Support skipped tests
thunderbolt: test: Reinstate a few casts of bitfields
kunit: tool: internal refactor of parser input handling
lib/test: convert lib/test_list_sort.c to use KUnit
kunit: introduce kunit_kmalloc_array/kunit_kcalloc() helpers
kunit: Remove the unused all_tests.config
kunit: Move default config from arch/um -> tools/testing/kunit
kunit: arch/um/configs: Enable KUNIT_ALL_TESTS by default
kunit: Add gnu_printf specifiers
lib/cmdline_kunit: Remove a cast which are no-longer required
kernel/sysctl-test: Remove some casts which are no-longer required
thunderbolt: test: Remove some casts which are no longer required
mmc: sdhci-of-aspeed: Remove some unnecessary casts from KUnit tests
iio: Remove a cast in iio-test-format which is no longer required
device property: Remove some casts in property-entry-test
Documentation: kunit: Clean up some string casts in examples
...
KUnit's EXPECT macros no longer typecheck as stringently, so casting the
result of strcmp() is now unnecessary.
Signed-off-by: David Gow <davidgow@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Allocating an IRQ is conditional to the IRQ existence, but freeing it
was not. If no IRQ was allocate, the driver would still try to free
IRQ 0. Add the missing checks.
This fixes the following trace when the driver is removed:
[ 100.667788] Trying to free already-free IRQ 0
[ 100.667793] WARNING: CPU: 0 PID: 2315 at kernel/irq/manage.c:1826 free_irq+0x1fd/0x370
...
[ 100.667914] Call Trace:
[ 100.667920] tcs3472_remove+0x3a/0x90 [tcs3472]
[ 100.667927] i2c_device_remove+0x2b/0xa0
Signed-off-by: frank zago <frank@zago.net>
Link: https://lore.kernel.org/r/20210427022017.19314-2-frank@zago.net
Fixes: 9d2f715d59 ("iio: light: tcs3472: support out-of-threshold events")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is quite strange that BMA222 and BMA222E have very close, yet
subtly different values in their scale tables. Comparing the datasheets
this is simply because the "Resolution" for the different measurement
ranges are documented with different precision.
For example, for +-2g the BMA222 datasheet [1] suggests a resolution
of 15.6 mg/LSB, while the BMA222E datasheet [2] suggests 15.63 mg/LSB.
Actually, there is no need to rely on the resolution given by the Bosch
datasheets. The resolution and scale can be calculated more consistently
and accurately using the range (e.g. +-2g) and the channel size (e.g. 8 bits).
Distributing 4g (-2g to 2g) over 8 bits results in an exact resolution
of (4g / 2^8) = 15.625 mg/LSB which is the same value as in both datasheets,
just slightly more accurate. Multiplying g = 9.80665 m/s^2 we get a more
accurate value for the IIO scale table.
Generalizing this we can calculate the scale tables more accurately using
(range / 2^bits) * g * 10^6 (because of IIO_VAL_INT_PLUS_MICRO).
Document this and make the scale tables more consistent and accurate
for all the variants using that formula. Now the scale tables for
BMA222 and BMA222E are consistent and probably slightly more accurate.
[1]: https://media.digikey.com/pdf/Data%20Sheets/Bosch/BMA222.pdf
[2]: https://www.mouser.com/datasheet/2/783/BST-BMA222E-DS004-06-1021076.pdf
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gnail.com>
Link: https://lore.kernel.org/r/20210611182442.1971-1-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
General driver churn doesn't always include updates of header includes.
Manual review of the output of the include-what-you-use checker lead to the
following cleanup. Hopefuly this brings things back to a good state for the
hid-sensor drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210608205510.4033887-1-jic23@kernel.org
The devm_ handled runtime pm disable calls pm_runtime_put_sync_suspend()
which isn't balancing a matching get call. It isn't a bug as such,
because the runtime pm core doesn't decrement the reference count below
zero, but it is missleading so let's drop it.
Using pm_runtime_resume_and_get() new call makes it easy to handle
failures in resume as it doesn't hold a reference count if it exits
with an error.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210516162103.1332291-7-jic23@kernel.org
Using this new call makes it easy to handle any errors as a result
of runtime resume as it exits without leaving the reference count
elevated.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210516162103.1332291-6-jic23@kernel.org
The pm_runtime_put_noidle() call in remove isn't balanced with any get, so
drop it. Note this isn't a bug as the runtime pm core will not allow the
reference count to go negative, making this a noop. However, it is
confusing to the reader so let's drop it.
pm_runtime_resume_and_get() replacement found using the coccicheck script
under review at:
https://lore.kernel.org/lkml/20210427141946.2478411-1-Julia.Lawall@inria.fr/
As pm_runtime_resume_and_get() returns <= 0 take advantage of that to
change the error checking to if (ret) which is more in keeping with the
rest of this driver.
This is a prequel to taking a closer look at the runtime pm in IIO drivers
in general.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210516162103.1332291-4-jic23@kernel.org
The call to pm_runtime_put_noidle() in remove() is not balancing a
counter increment. Note this doesn't matter as the runtime pm core
will not allow the counter to go negative. However, it is confusing
to the reader so let's remove it.
The pm_runtime_resume_and_get() replacement was found using coccicheck
script under review at:
https://lore.kernel.org/lkml/20210427141946.2478411-1-Julia.Lawall@inria.fr/
This is a prequel to taking a closer look at the runtime pm in IIO drivers
in general.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210516162103.1332291-3-jic23@kernel.org
Remove an unblanced pm_runtime_put_sync_suspend() call
in inv_pu_pm_disable(). Not this call is not a bug, because the runtime
pm core will not allow the reference counter to go negative. It is
however confusing and serves no purpose.
pm_runtime_resume_and_get() case found using coccicheck script under
review at:
https://lore.kernel.org/lkml/20210427141946.2478411-1-Julia.Lawall@inria.fr/
pm_runtime_resume_and_get() returns <= 0 only so simplify related checks
to bring this more inline with nearby calls.
This is a prequel to taking a closer look at the runtime pm in IIO drivers
in general.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210516162103.1332291-2-jic23@kernel.org
A namespace for exported symbols makes clear who is a provider
and who is a consumer of the certain resources. Besides that,
it doesn't pollute the common namespace.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210614162447.5392-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Fixes: 1c28799257 ("iio: light: isl29501: Add support for the ISL29501 ToF sensor.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mathieu Othacehe <m.othacehe@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-9-jic23@kernel.org
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a potential
kernel data leak, making for a less minimal fix.
Fixes: 55707294c4 ("iio: light: Add support for vishay vcnl4035")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-8-jic23@kernel.org
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Found during an audit of all callers of iio_push_to_buffers_with_timestamp()
Fixes: 8fe78d5261 ("iio: vcnl4000: Add buffer support for VCNL4010/20.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mathieu Othacehe <m.othacehe@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-7-jic23@kernel.org
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because this buffer is used in
a non-trivial way for data repacking.
Fixes: 121354b2ec ("iio: magnetometer: Add driver support for PNI RM3100")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Song Qiang <songqiang1304521@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-6-jic23@kernel.org
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Fixes: f214ff521f ("iio: ti-ads8688: Update buffer allocation for timestamps")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-5-jic23@kernel.org
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Add a comment on why the buffer is the size it is as not immediately
obvious.
Found during an audit of all calls of this function.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-4-jic23@kernel.org
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of this function.
Fixes: d3bf60450d ("iio: hx711: add triggered buffer support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-3-jic23@kernel.org
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of this function.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-2-jic23@kernel.org
This patch marks the struct ltr501_chip_info as constant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559
Link: https://lore.kernel.org/r/20210610134619.2101372-5-mkl@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The PS ADC Channel data is spread over 2 registers in little-endian
form. This patch adds the missing endianness conversion.
Fixes: 2690be9051 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Signed-off-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559
Link: https://lore.kernel.org/r/20210610134619.2101372-4-mkl@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ltr559 chip uses only the lowest bit of the ALS_CONTR register to
configure between active and stand-by mode. In the original driver
BIT(1) is used, which does a software reset instead.
This patch fixes the problem by using BIT(0) as als_mode_active for
the ltr559 chip.
Fixes: 8592a7eefa ("iio: ltr501: Add support for ltr559 chip")
Signed-off-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559
Link: https://lore.kernel.org/r/20210610134619.2101372-3-mkl@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The regmap is configured for 8 bit registers, uses a RB-Tree cache and
marks several registers as volatile (i.e. do not cache).
The ALS and PS data registers in the chip are 16 bit wide and spans
two regmap registers. In the current driver only the base register is
marked as volatile, resulting in the upper register only read once.
Further the data sheet notes:
| When the I2C read operation starts, all four ALS data registers are
| locked until the I2C read operation of register 0x8B is completed.
Which results in the registers never update after the 2nd read.
This patch fixes the problem by marking the upper 8 bits of the ALS
and PS registers as volatile, too.
Fixes: 2f2c96338a ("iio: ltr501: Add regmap support.")
Reported-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559
Link: https://lore.kernel.org/r/20210610134619.2101372-2-mkl@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit c1d1c4a62d ("iio: accel: bma180: BMA254 support") added
BMA254 support to the bma180 driver and changed some naming to BMA25x
to make it easier to add support for BMA253 and BMA255.
Unfortunately, there is quite some overlap between the bma180 driver
and the bmc150-accel driver. Back when the commit was made, the
bmc150-accel driver actually already had support for BMA255, and
adding support for BMA254 would have been as simple as adding a new
compatible to bmc150-accel.
The bmc150-accel driver is a bit better for BMA254 since it also
supports the motion trigger/interrupt functionality. Fortunately,
moving BMA254 support over to bmc150-accel is fairly simple because
the drivers have compatible device tree bindings.
Revert most of the changes for BMA254 support in bma180 and move
BMA254 over to bmc150-accel. This has the following advantages:
- Support for motion trigger/interrupt
- Fix incorrect scale values (BMA254 currently uses the same as
BMA250 but actually they're different because of 10 vs 12 bits
data size)
- Less code than before :)
BMA250 could be potentially also moved but it's more complicated
because its chip_id conflicts with the one for BMA222 in bmc150-accel.
Perhaps there are also other register differences, I did not investigate
further yet (and I have no way to test it).
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-11-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
BMA253 is mostly like BMA255 and has exactly the same register layout
as used by the bmc150-accel driver as far I can tell. Making it work
is as simple as adding new device IDs for it since it has the same
chip_id = 0xFA (250) as BMA255 and others.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-8-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Right now all the device IDs are listed in seemingly random order,
make this consistent by ordering those alphabetically. Also, order
bmc150_accel_chip_info_tbl by chip ID for the same reason.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-6-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chips supported by the bmc150-accel driver are clearly documented
in Kconfig, in the bmc150_accel_chip_info_tbl as well as in all the
device ID tables in the I2C/SPI drivers. It's easy to forget to update
the lists in the file header. Drop those entirely to reduce the amount
of changes required to add new chip variants.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-5-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 0ad4bf3701 ("iio:accel:bmc150-accel: Use the chip ID to detect
sensor variant") stopped using the I2C/ACPI match data to look up the
bmc150_accel_chip_info. However, the bmc150_accel_chip_info_tbl remained
as-is, with multiple entries with the same chip_id (e.g. 0xFA for
BMC150/BMI055/BMA255). This is redundant now because actually the driver
will always select the first entry with a matching chip_id.
So even if a device probes e.g. with BMA0255 it will end up using the
chip_info for BMC150. And in general that's fine for now, the entries
for BMC150/BMI055/BMA255 were exactly the same anyway (except for the
name, which is replaced with the more accurate one later).
But in this case it's misleading because it suggests that one should
add even more entries with the same chip_id when adding support for
new variants. Let's make that more clear by removing the enum with
the chip identifiers entirely and instead have only one entry per
chip_id.
Note that we may need to bring back some mechanism to differentiate
between different chips with the same chip_id in the future.
For example, BMA250 (currently supported by the bma180 driver) has the
same chip_id = 0x03 as BMA222 even though they have different channel
sizes (8 bits vs 10 bits). But in any case, that mechanism would
need to look quite different from what we have right now.
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-4-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Kconfig option currently says that all Bosch accelerometers
supported by the bmc150-accel driver are combo chips with both
accelerometer and magnetometer. This is wrong: actually only BMC150
is such a combo. The BMA* variants only contain an accelerometer
and the BMI055 actually is a accelerometer + gyroscope combo.
Clarify this in the help text and also make the list of supported
variants complete and sorted for consistency.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-3-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to sysfs-bus-iio documentation the unit for accelerometer
values after applying scale/offset should be m/s^2, not g, which explains
why the scale values for the other variants in bmc150-accel do not match
exactly the values given in the datasheet.
To get the correct values, we need to multiply the BMA222 scale values
by g = 9.80665 m/s^2.
Fixes: a1a210bf29 ("iio: accel: bmc150-accel: Add support for BMA222")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-2-stephan@gerhold.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gcc reports build error when CONFIG_IIO_TRIGGERED_BUFFER is not set:
riscv64-linux-gnu-ld: drivers/iio/dummy/iio_simple_dummy_buffer.o: in function `iio_simple_dummy_configure_buffer':
iio_simple_dummy_buffer.c:(.text+0x2b0): undefined reference to `iio_triggered_buffer_setup_ext'
riscv64-linux-gnu-ld: drivers/iio/dummy/iio_simple_dummy_buffer.o: in function `.L0 ':
iio_simple_dummy_buffer.c:(.text+0x2fc): undefined reference to `iio_triggered_buffer_cleanup'
Fix it by select IIO_TRIGGERED_BUFFER for config IIO_SIMPLE_DUMMY_BUFFER.
Fixes: 738f6ba118 ("iio: dummy: iio_simple_dummy_buffer: use triggered buffer core calls")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Disable reg and clk when devm_gpiod_get_optional() fails in adf4350_probe().
Fixes:4a89d2f47ccd ("iio: adf4350: Convert to use GPIO descriptor")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210601142605.3613605-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the BMA253 datasheet [1] and BMA250 datasheet [2] the
bandwidth value for BMA25x should be set as 01xxx:
"Settings 00xxx result in a bandwidth of 7.81 Hz; [...]
It is recommended [...] to use the range from ´01000b´ to ´01111b´
only in order to be compatible with future products."
However, at the moment the drivers sets bandwidth values from 0 to 6,
which is not recommended and always results into 7.81 Hz bandwidth
according to the datasheet.
Fix this by introducing a bw_offset = 8 = 01000b for BMA25x,
so the additional bit is always set for BMA25x.
[1]: https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bma253-ds000.pdf
[2]: https://datasheet.octopart.com/BMA250-Bosch-datasheet-15540103.pdf
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Fixes: 2017cff24c ("iio:bma180: Add BMA250 chip support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210526094408.34298-2-stephan@gerhold.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO ADC group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513111035.77950-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO IMU group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513122512.93187-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since all AD Sigma-Delta drivers now use the
devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old
ad_sd_{setup,cleanup}_buffer_and_trigger() functions.
This way we can discourage new drivers that use the ad_sigma_delta
lib-driver to use these (older functions).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-13-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As not many steps were not already devm_ managed, use
devm_add_action_or_reset() to handle the rest.
This also uses the new devm_ad_sd_setup_buffer_and_trigger() function.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-12-aardelean@deviqon.com
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7192 driver to use device-managed
functions.
The regulators and the mclk requires devm_add_action_or_reset() callbacks
though.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-11-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_optional() helper returns NULL when devm_clk_get() returns
-ENOENT.
This makes things slightly cleaner. The added benefit is mostly cosmetic.
Also, a minor detail with this call, is that the reference for the parent
device is taken as `spi->dev` instead of `&st->sd.spi->dev` (which looks a
little quirky).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-10-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7780 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-9-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Linus Torvalds
Andreas Kemnade
Colin Ian King
Chris Lesiak
Arnd Bergmann
Antti Keränen
Uwe Kleine-König
Sean Nyekjaer
David Gow
frank zago
Stephan Gerhold
Jonathan Cameron
Andy Shevchenko
Marc Kleine-Budde
Oliver Lang
Tom Rix
Wei Yongjun
Yang Yingliang
Alexandru Ardelean