With the VIOT support in place, x86 platforms can now use the
virtio-iommu.
Because the other x86 IOMMU drivers aren't yet ready to use the
acpi_dma_setup() path, x86 doesn't implement arch_setup_dma_ops() at the
moment. Similarly to Vt-d and AMD IOMMU, clear the DMA ops and call
iommu_setup_dma_ops() from probe_finalize().
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210618152059.1194210-6-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The ACPI Virtual I/O Translation Table describes topology of
para-virtual platforms, similarly to vendor tables DMAR, IVRS and IORT.
For now it describes the relation between virtio-iommu and the endpoints
it manages.
Three steps are needed to configure DMA of endpoints:
(1) acpi_viot_init(): parse the VIOT table, find or create the fwnode
associated to each vIOMMU device. This needs to happen after
acpi_scan_init(), because it relies on the struct device and their
fwnode to be available.
(2) When probing the vIOMMU device, the driver registers its IOMMU ops
within the IOMMU subsystem. This step doesn't require any
intervention from the VIOT driver.
(3) viot_iommu_configure(): before binding the endpoint to a driver,
find the associated IOMMU ops. Register them, along with the
endpoint ID, into the device's iommu_fwspec.
If step (3) happens before step (2), it is deferred until the IOMMU is
initialized, then retried.
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20210618152059.1194210-4-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The IOMMU in many SoC depends on the MM clocks and power-domain which
are device_initcall normally, thus the subsys_init here is not helpful.
This patch switches it to module_platform_driver which also allow the
driver built as module.
Correspondingly switch the config to tristate, and update the
iommu_ops's owner.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210326032337.24578-2-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch only adds support for building the IOMMU-v1 driver as module.
Correspondingly switch the config to tristate and update the iommu_ops's
owner to THIS_MODULE.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210326032337.24578-1-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This IOMMU module can be used by Unisoc's multimedia devices, such as
display, Image codec(jpeg) and a few signal processors, including
VSP(video), GSP(graphic), ISP(image), and CPP(camera pixel processor), etc.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210305093216.201897-3-zhang.lyra@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The sva_bind() function allows devices to access process address spaces
using a PASID (aka SSID).
(1) bind() allocates or gets an existing MMU notifier tied to the
(domain, mm) pair. Each mm gets one PASID.
(2) Any change to the address space calls invalidate_range() which sends
ATC invalidations (in a subsequent patch).
(3) When the process address space dies, the release() notifier disables
the CD to allow reclaiming the page tables. Since release() has to
be light we do not instruct device drivers to stop DMA here, we just
ignore incoming page faults from this point onwards.
To avoid any event 0x0a print (C_BAD_CD) we disable translation
without clearing CD.V. PCIe Translation Requests and Page Requests
are silently denied. Don't clear the R bit because the S bit can't
be cleared when STALL_MODEL==0b10 (forced), and clearing R without
clearing S is useless. Faulting transactions will stall and will be
aborted by the IOPF handler.
(4) After stopping DMA, the device driver releases the bond by calling
unbind(). We release the MMU notifier, free the PASID and the bond.
Three structures keep track of bonds:
* arm_smmu_bond: one per {device, mm} pair, the handle returned to the
device driver for a bind() request.
* arm_smmu_mmu_notifier: one per {domain, mm} pair, deals with ATS/TLB
invalidations and clearing the context descriptor on mm exit.
* arm_smmu_ctx_desc: one per mm, holds the pinned ASID and pgd.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20201106155048.997886-4-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Let IOMMU drivers allocate a single PASID per mm. Store the mm in the
IOASID set to allow refcounting and searching mm by PASID, when handling
an I/O page fault.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201106155048.997886-3-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
With Shared Virtual Addressing (SVA), we need to mirror CPU TTBR, TCR,
MAIR and ASIDs in SMMU contexts. Each SMMU has a single ASID space split
into two sets, shared and private. Shared ASIDs correspond to those
obtained from the arch ASID allocator, and private ASIDs are used for
"classic" map/unmap DMA.
A possible conflict happens when trying to use a shared ASID that has
already been allocated for private use by the SMMU driver. This will be
addressed in a later patch by replacing the private ASID. At the
moment we return -EBUSY.
Each mm_struct shared with the SMMU will have a single context
descriptor. Add a refcount to keep track of this. It will be protected
by the global SVA lock.
Introduce a new arm-smmu-v3-sva.c file and the CONFIG_ARM_SMMU_V3_SVA
option to let users opt in SVA support.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20200918101852.582559-9-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
ipmmu-vmsa driver is also used on Renesas RZ/G{1,2} Soc's, update the
same to reflect the help description for IPMMU_VMSA config.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200911101912.20701-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Including:
- Removal of the dev->archdata.iommu (or similar) pointers from
most architectures. Only Sparc is left, but this is private to
Sparc as their drivers don't use the IOMMU-API.
- ARM-SMMU Updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell
Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d Updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel
drivers into their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test
coverage)
-----BEGIN PGP SIGNATURE-----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=3O2Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Remove of the dev->archdata.iommu (or similar) pointers from most
architectures. Only Sparc is left, but this is private to Sparc as
their drivers don't use the IOMMU-API.
- ARM-SMMU updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel drivers into
their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test coverage)
* tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (77 commits)
iommu/amd: Move Kconfig and Makefile bits down into amd directory
iommu/vt-d: Move Kconfig and Makefile bits down into intel directory
iommu/arm-smmu: Move Arm SMMU drivers into their own subdirectory
iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu
iommu: Add gfp parameter to io_pgtable_ops->map()
iommu: Mark __iommu_map_sg() as static
iommu/vt-d: Rename intel-pasid.h to pasid.h
iommu/vt-d: Add page response ops support
iommu/vt-d: Report page request faults for guest SVA
iommu/vt-d: Add a helper to get svm and sdev for pasid
iommu/vt-d: Refactor device_to_iommu() helper
iommu/vt-d: Disable multiple GPASID-dev bind
iommu/vt-d: Warn on out-of-range invalidation address
iommu/vt-d: Fix devTLB flush for vSVA
iommu/vt-d: Handle non-page aligned address
iommu/vt-d: Fix PASID devTLB invalidation
iommu/vt-d: Remove global page support in devTLB flush
iommu/vt-d: Enforce PASID devTLB field mask
iommu: Make some functions static
iommu/amd: Remove double zero check
...
Move AMD Kconfig and Makefile bits down into the amd directory
with the rest of the AMD specific files.
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200630200636.48600-3-jsnitsel@redhat.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move Intel Kconfig and Makefile bits down into intel directory
with the rest of the Intel specific files.
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200630200636.48600-2-jsnitsel@redhat.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Avoid the overhead of the dma ops support for tiny builds that only
use the direct mapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
This driver shouldn't need anything architecture-specific (that isn't
under CONFIG_ARM protection already), and has already been accessible
from certain x86 configurations by virtue of the previously-cleaned-up
"ARM || IOMMU_DMA" dependency. Allow COMPILE_TEST for all architectures.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1fe2006aa98f008a2e689adba6e8c96e9197f903.1593791968.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Wacky COMPILE_TEST dependencies based on who used to define
dev_archdata.iommu can go.
Dependencies on ARM or ARM64 already implied by the ARCH_* platform
selection can go.
The entire IOMMU_SUPPORT menu already depends on MMU, so those can go.
IOMMU_DMA is for the architecture's DMA API implementation to choose,
and its interface to IOMMU drivers is properly stubbed out if disabled,
so dependencies on or selections of that can go (AMD_IOMMU is the
current exception since the x86 drivers have to provide their own entire
dma_map_ops implementation).
Since commit ed6ccf10f2 ("dma-mapping: properly stub out the DMA API
for !CONFIG_HAS_DMA"), drivers which simply use the dma-mapping API
should not need to depend on HAS_DMA, so those can go.
And a long-dead option for code removed from the MSM driver 4 years ago
can also go.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/7fb9c74dc6bd12a4619ca44c92408e91352f1be0.1593791968.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
If NO_DMA=y (e.g. Sun-3 all{mod,yes}-config):
drivers/iommu/dma-iommu.o: In function `iommu_dma_mmap':
dma-iommu.c:(.text+0x92e): undefined reference to `dma_pgprot'
IOMMU_DMA must not be selected, unless HAS_DMA=y.
Hence fix this by making SUN50I_IOMMU depend on HAS_DMA.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200629121146.24011-1-geert@linux-m68k.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Current Intel SVM is designed by setting the pgd_t of the processor page
table to FLPTR field of the PASID entry. The first level translation only
supports 4 and 5 level paging structures, hence it's infeasible for the
IOMMU to share a processor's page table when it's running in 32-bit mode.
Let's disable 32bit support for now and claim support only when all the
missing pieces are ready in the future.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Suggested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200622231345.29722-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The Allwinner H6 has introduced an IOMMU for a few DMA controllers, mostly
video related: the display engine, the video decoders / encoders, the
camera capture controller, etc.
The design is pretty simple compared to other IOMMUs found in SoCs: there's
a single instance, controlling all the masters, with a single address
space.
It also features a performance monitoring unit that allows to retrieve
various informations (per-master and global TLB accesses, hits and misses,
access latency, etc) that isn't supported at the moment.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/d122a8670361e36fc26b4ce2674a2223d30dc4cc.1589378833.git-series.maxime@cerno.tech
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Although SPAPR_TCE_IOMMU itself can be compile tested on certain PowerPC
configurations, its presence makes arch/powerpc/kvm/Makefile to select
modules which do not build in such configuration.
The arch/powerpc/kvm/ modules use kvm_arch.spapr_tce_tables which exists
only with CONFIG_PPC_BOOK3S_64. However these modules are selected when
COMPILE_TEST and SPAPR_TCE_IOMMU are chosen leading to build failures:
In file included from arch/powerpc/include/asm/book3s/64/mmu-hash.h:20:0,
from arch/powerpc/kvm/book3s_64_vio_hv.c:22:
arch/powerpc/include/asm/book3s/64/pgtable.h:17:0: error: "_PAGE_EXEC" redefined [-Werror]
#define _PAGE_EXEC 0x00001 /* execute permission */
In file included from arch/powerpc/include/asm/book3s/32/pgtable.h:8:0,
from arch/powerpc/include/asm/book3s/pgtable.h:8,
from arch/powerpc/include/asm/pgtable.h:18,
from include/linux/mm.h:95,
from arch/powerpc/include/asm/io.h:29,
from include/linux/io.h:13,
from include/linux/irq.h:20,
from arch/powerpc/include/asm/hardirq.h:6,
from include/linux/hardirq.h:9,
from include/linux/kvm_host.h:7,
from arch/powerpc/kvm/book3s_64_vio_hv.c:12:
arch/powerpc/include/asm/book3s/32/hash.h:29:0: note: this is the location of the previous definition
#define _PAGE_EXEC 0x200 /* software: exec allowed */
Fixes: e93a1695d7 ("iommu: Enable compile testing for some of drivers")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200414142630.21153-1-krzk@kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
If NO_DMA=y (e.g. Sun-3 all{mod,yes}-config):
drivers/iommu/dma-iommu.o: In function `iommu_dma_mmap':
dma-iommu.c:(.text+0x836): undefined reference to `dma_pgprot'
IOMMU_DMA must not be selected, unless HAS_DMA=y.
Hence fix this by making MTK_IOMMU depend on HAS_DMA.
While at it, remove the dependency on ARM || ARM64, as that is already
implied by the dependency on ARCH_MEDIATEK.
Fixes: e93a1695d7 ("iommu: Enable compile testing for some of drivers")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20200410143047.19691-1-geert@linux-m68k.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOASID code is needed by VT-d scalable mode for PASID allocation.
Add explicit dependency such that IOASID is built-in whenever Intel
IOMMU is enabled.
Otherwise, aux domain code will fail when IOMMU is built-in and IOASID
is compiled as a module.
Fixes: 59a623374d ("iommu/vt-d: Replace Intel specific PASID allocator with IOASID")
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some of the IOMMU drivers can be compile tested to increase build
coverage. The OMAP, Rockchip and Exynos drivers use
device.dev_archdata.iommu field which does not exist on all platforms.
The sPAPR TCE and ARM SMMU have also restrictions where they can be
built.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Now that the infrastructure changes are in place, enable virtio-iommu to
be built as a module. Remove the redundant pci_request_acs() call, since
it's not exported but is already invoked during DMA setup.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Make use of generic IOASID code to manage PASID allocation,
free, and lookup. Replace Intel specific code.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This adds Kconfig option INTEL_IOMMU_SCALABLE_MODE_DEFAULT_ON
to make it easier for distributions to enable or disable the
Intel IOMMU scalable mode by default during kernel build.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
By conditionally dropping support for the legacy binding and exporting
the newly introduced 'arm_smmu_impl_init()' function we can allow the
ARM SMMU driver to be built as a module.
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: John Garry <john.garry@huawei.com> # smmu v3
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
By removing the redundant call to 'pci_request_acs()' we can allow the
ARM SMMUv3 driver to be built as a module.
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: John Garry <john.garry@huawei.com> # smmu v3
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
Including:
- Conversion of the AMD IOMMU driver to use the dma-iommu code
for imlementing the DMA-API. This gets rid of quite some code
in the driver itself, but also has some potential for
regressions (non are known at the moment).
- Support for the Qualcomm SMMUv2 implementation in the SDM845
SoC. This also includes some firmware interface changes, but
those are acked by the respective maintainers.
- Preparatory work to support two distinct page-tables per
domain in the ARM-SMMU driver
- Power management improvements for the ARM SMMUv2
- Custom PASID allocator support
- Multiple PCI DMA alias support for the AMD IOMMU driver
- Adaption of the Mediatek driver to the changed IO/TLB flush
interface of the IOMMU core code.
- Preparatory patches for the Renesas IOMMU driver to support
future hardware.
-----BEGIN PGP SIGNATURE-----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=ntaE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Conversion of the AMD IOMMU driver to use the dma-iommu code for
imlementing the DMA-API. This gets rid of quite some code in the
driver itself, but also has some potential for regressions (non are
known at the moment).
- Support for the Qualcomm SMMUv2 implementation in the SDM845 SoC.
This also includes some firmware interface changes, but those are
acked by the respective maintainers.
- Preparatory work to support two distinct page-tables per domain in
the ARM-SMMU driver
- Power management improvements for the ARM SMMUv2
- Custom PASID allocator support
- Multiple PCI DMA alias support for the AMD IOMMU driver
- Adaption of the Mediatek driver to the changed IO/TLB flush interface
of the IOMMU core code.
- Preparatory patches for the Renesas IOMMU driver to support future
hardware.
* tag 'iommu-updates-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (62 commits)
iommu/rockchip: Don't provoke WARN for harmless IRQs
iommu/vt-d: Turn off translations at shutdown
iommu/vt-d: Check VT-d RMRR region in BIOS is reported as reserved
iommu/arm-smmu: Remove duplicate error message
iommu/arm-smmu-v3: Don't display an error when IRQ lines are missing
iommu/ipmmu-vmsa: Add utlb_offset_base
iommu/ipmmu-vmsa: Add helper functions for "uTLB" registers
iommu/ipmmu-vmsa: Calculate context registers' offset instead of a macro
iommu/ipmmu-vmsa: Add helper functions for MMU "context" registers
iommu/ipmmu-vmsa: tidyup register definitions
iommu/ipmmu-vmsa: Remove all unused register definitions
iommu/mediatek: Reduce the tlb flush timeout value
iommu/mediatek: Get rid of the pgtlock
iommu/mediatek: Move the tlb_sync into tlb_flush
iommu/mediatek: Delete the leaf in the tlb_flush
iommu/mediatek: Use gather to achieve the tlb range flush
iommu/mediatek: Add a new tlb_lock for tlb_flush
iommu/mediatek: Correct the flush_iotlb_all callback
iommu/io-pgtable-arm: Rename IOMMU_QCOM_SYS_CACHE and improve doc
iommu/io-pgtable-arm: Rationalise MAIR handling
...
Currently hyperv-iommu is implemented in a x86 specific way, for
example, apic is used. So make the HYPERV_IOMMU Kconfig depend on X86
as a preparation for enabling HyperV on architecture other than x86.
Cc: Lan Tianyu <Tianyu.Lan@microsoft.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: linux-hyperv@vger.kernel.org
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously intel-iommu.c depended on CONFIG_AMD_IOMMU in an undesirable
way. When CONFIG_INTEL_IOMMU_SVM=y, iommu_enable_dev_iotlb() calls PRI
interfaces (pci_reset_pri() and pci_enable_pri()), but those are only
implemented when CONFIG_PCI_PRI is enabled.
The INTEL_IOMMU_SVM Kconfig did nothing with PCI_PRI, but AMD_IOMMU selects
PCI_PRI. So if AMD_IOMMU was enabled, intel-iommu.c got the full PRI
interfaces, but if AMD_IOMMU was not enabled, it got the PRI stubs.
Make the iommu_enable_dev_iotlb() behavior independent of AMD_IOMMU by
having INTEL_IOMMU_SVM select PCI_PRI so iommu_enable_dev_iotlb() always
uses the full implementations of PRI interfaces.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Some devices might support multiple DMA address spaces, in particular
those that have the PCI PASID feature. PASID (Process Address Space ID)
allows to share process address spaces with devices (SVA), partition a
device into VM-assignable entities (VFIO mdev) or simply provide
multiple DMA address space to kernel drivers. Add a global PASID
allocator usable by different drivers at the same time. Name it I/O ASID
to avoid confusion with ASIDs allocated by arch code, which are usually
a separate ID space.
The IOASID space is global. Each device can have its own PASID space,
but by convention the IOMMU ended up having a global PASID space, so
that with SVA, each mm_struct is associated to a single PASID.
The allocator is primarily used by IOMMU subsystem but in rare occasions
drivers would like to allocate PASIDs for devices that aren't managed by
an IOMMU, using the same ID space as IOMMU.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the AMD iommu driver to the dma-iommu api. Remove the iova
handling and reserve region code from the AMD iommu driver.
Signed-off-by: Tom Murphy <murphyt7@tcd.ie>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
-----BEGIN PGP SIGNATURE-----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=L5e+
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
The bounce page implementation depends on swiotlb. Hence, don't
switch off swiotlb if the system has untrusted devices or could
potentially be hot-added with any untrusted devices.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The only thing remaining of the machvecs is a few checks if we are
running on an SGI UV system. Replace those with the existing
is_uv_system() check that has been rewritten to simply check the
OEM ID directly.
That leaves us with a generic kernel that is as fast as the previous
DIG/ZX1/UV kernels, but can support all hardware. Support for UV
and the HP SBA IOMMU is now optional based on new config options.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-27-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The virtio IOMMU is a para-virtualized device, allowing to send IOMMU
requests such as map/unmap over virtio transport without emulating page
tables. This implementation handles ATTACH, DETACH, MAP and UNMAP
requests.
The bulk of the code transforms calls coming from the IOMMU API into
corresponding virtio requests. Mappings are kept in an interval tree
instead of page tables. A little more work is required for modular and x86
support, so for the moment the driver depends on CONFIG_VIRTIO=y and
CONFIG_ARM64.
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
On RT, iommu_dma_map_msi_msg() may be called from non-preemptible
context. This will lead to a splat with CONFIG_DEBUG_ATOMIC_SLEEP as
the function is using spin_lock (they can sleep on RT).
iommu_dma_map_msi_msg() is used to map the MSI page in the IOMMU PT
and update the MSI message with the IOVA.
Only the part to lookup for the MSI page requires to be called in
preemptible context. As the MSI page cannot change over the lifecycle
of the MSI interrupt, the lookup can be cached and re-used later on.
iomma_dma_map_msi_msg() is now split in two functions:
- iommu_dma_prepare_msi(): This function will prepare the mapping
in the IOMMU and store the cookie in the structure msi_desc. This
function should be called in preemptible context.
- iommu_dma_compose_msi_msg(): This function will update the MSI
message with the IOVA when the device is behind an IOMMU.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If you're bisecting why your peripherals stopped working, it's
probably this CL. Specifically if you see this in your dmesg:
Unexpected global fault, this could be serious
...then it's almost certainly this CL.
Running your IOMMU-enabled peripherals with the IOMMU in bypass mode
is insecure and effectively disables the protection they provide.
There are few reasons to allow unmatched stream bypass, and even fewer
good ones.
This patch starts the transition over to make it much harder to run
your system insecurely. Expected steps:
1. By default disable bypass (so anyone insecure will notice) but make
it easy for someone to re-enable bypass with just a KConfig change.
That's this patch.
2. After people have had a little time to come to grips with the fact
that they need to set their IOMMUs properly and have had time to
dig into how to do this, the KConfig will be eliminated and bypass
will simply be disabled. Folks who are truly upset and still
haven't fixed their system can either figure out how to add
'arm-smmu.disable_bypass=n' to their command line or revert the
patch in their own private kernel. Of course these folks will be
less secure.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Jean-Philippe Brucker
Joerg Roedel
Yong Wu
Chunyan Zhang
Lad Prabhakar
Linus Torvalds
Jerry Snitselaar
Christoph Hellwig
Robin Murphy
Geert Uytterhoeven
Lu Baolu
Masahiro Yamada
Maxime Ripard
Krzysztof Kozlowski
Jacob Pan
Jean-Philippe Brucker
Will Deacon
Boqun Feng
Bjorn Helgaas
Tom Murphy
Thomas Gleixner
Julien Grall
Douglas Anderson