Граф коммитов

357 Коммитов

Автор SHA1 Сообщение Дата
Sibi Sankar 4725496e48 remoteproc: q6v5: Allow defining GLINK edge for mss remoteproc
Add GLINK subdevice to allow definition of GLINK edge as a
child of modem-pil.

Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-29 20:10:34 -07:00
Sibi Sankar 231f67d1fb remoteproc: q6v5: Add support for mss remoteproc on SDM845
From SDM845, the Q6SS reset sequence on software side has been
simplified with the introduction of boot FSM which assists in
bringing the Q6 out of reset.

SDM845 brings a new reset signal ALT_RESET which is a part of
the MSS subsystem hence requires reset clks to be enabled before
assert/deassert. Use the SoC specific reset helper function to
add support for ALT_RESET in SDM845.

Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-29 20:10:34 -07:00
Sibi Sankar 9f135fa1ff remoteproc: q6v5: Introduce reset assert/deassert helper functions
Adding reset assert/deassert helper functions to handle SoC
specific reset sequences. This wil be used by SDM845 to assert and
deassert ALT_RESET and MSS_RESET signals.

Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-29 20:10:34 -07:00
Sibi Sankar 663e98453a remoteproc: q6v5: Move proxy unvote to handover irq handler
Introduce interrupt handler for smp2p ready interrupt to
handle start completion. Move the proxy votes for clocks
and regulators to the handover interrupt context.

Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: Only proxy unvote if handover irq has not fired]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-21 17:24:00 -07:00
Bjorn Andersson f4c428cfe4 remoteproc: q6v5: Return irq from q6v5_request_irq()
q6v5_request_irq() was supposed to return the irq number, but ret is
overwritten by the request_irq(), fix this and return the IRQ on
success.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-21 17:24:00 -07:00
Bartosz Golaszewski 24ff14172f remoteproc/davinci: use octal permissions for module_param()
Checkpatch recommends to use octal perms instead of S_IRUGO.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-09 14:31:00 -07:00
Bartosz Golaszewski 5d26f068a5 remoteproc/davinci: prepare and unprepare the clock where needed
We're currently switching the platform to using the common clock
framework. We need to explicitly prepare and unprepare the rproc
clock.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-09 14:30:53 -07:00
Bartosz Golaszewski 2310eae90f remoteproc/davinci: add the missing retval check for clk_enable()
The davinci platform is being switched to using the common clock
framework, where clk_enable() can fail. Add the return value check.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-09 14:30:34 -07:00
Bjorn Andersson 9935448e20 Linux 4.17-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlrvwLAeHHRvcnZhbGRz
 QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGEX4H/iRAefubpMXptH55
 ru/Mr7hsbKtKQOCmH3LuYP2SwSEHclX+kxHfiaIMsBN9iOGWpRJkZVLuOG0Vl0sZ
 d68I5UTEJHPY0FZqOvfXY1sLTfG9jlhQ/SyppVyuL+QbH+cecnWqvkMkwo2p99MJ
 7OZ3wZjSObaJGXEoLUbZrEbTf8PsT8eT7MWMkmOJHO/J8rnnoDKaOiB5fBxhck0M
 xd/FdOYNZhqOfzIMUuLPWPE3THjfJuIQOYsTvEq0lcuAD2ZOesbV5hsGLC1AG6jd
 GaJJKy80mRvPXSLv7GTigBG9zZbs0mszDJeeh0FCjSlc3sjMDZn7A12N1c8AcQ52
 rLmzSQ8=
 =Nmna
 -----END PGP SIGNATURE-----

Merge tag 'v4.17-rc4' into rproc-next

Pick up fixes from rproc-v4.17-1

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-09 11:59:07 -07:00
Geert Uytterhoeven 41a5985f17 remoteproc: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.

Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.

This simplifies the dependencies, and allows to improve compile-testing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-04-25 20:37:39 -07:00
Tobias Jordan 278d744c46 remoteproc: qcom: Fix potential device node leaks
Add missing of_node_put()s at two places for device nodes returned by
of_parse_phandle().

Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating
 Hexagon v5")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-04-25 16:46:55 -07:00
Arnaud Pouliquen fcd58037f2 remoteproc: fix crashed parameter logic on stop call
Fix rproc_add_subdev parameter name and inverse the crashed logic.

Fixes: 880f5b3882 ("remoteproc: Pass type of shutdown to subdev remove")
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-04-25 16:43:55 -07:00
Sibi Sankar 2724807f7f remoteproc: Prevent incorrect rproc state on xfer mem ownership failure
Any failure in the secure call for transferring mem ownership of mba
region to Q6 would result in reporting that the remoteproc device
is running. This is because the previous q6v5_clk_enable would have
been a success. Prevent this by updating variable 'ret' accordingly.

Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-04-17 14:41:00 -07:00
Sibi Sankar 730b2ad8f7 remoteproc: fix null pointer dereference on glink only platforms
Currently calling list_del on smd subdev remove path results in
null pointer dereference on glink only platforms. Fix this by
adding safety checks in glink/smd subdev remove paths.

Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-04-05 22:53:16 -07:00
Arnd Bergmann dea4bd1975 soc: qcom: qmi: add CONFIG_NET dependency
Access to the socket API and the root network namespace is only available
when networking is enabled:

ERROR: "kernel_sendmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_release" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_create_kern" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_getsockname" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "init_net" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_recvmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!

Adding a dependency on CONFIG_NET lets us build it in all randconfig
builds.

Fixes: 9b8a11e826 ("soc: qcom: Introduce QMI encoder/decoder")
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-03-27 13:43:29 -07:00
Christophe JAILLET 99a31adfb2 remoteproc: imx_rproc: Slightly simplify code in 'imx_rproc_probe()'
We can return directly at the beginning of the function and save the 'err'
label.
We can also explicitly return 0 when the probe succeed.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-03-18 15:43:46 -07:00
Christophe JAILLET 96a30d7f91 remoteproc: imx_rproc: Re-use existing error handling path in 'imx_rproc_probe()'
Avoid some code ducplication and be more future-proof.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-03-18 15:43:46 -07:00
Christophe JAILLET de6f83f85b remoteproc: imx_rproc: Fix an error handling path in 'imx_rproc_probe()'
If 'of_device_get_match_data()' fails, we must undo the previous
'rproc_alloc()' call.

Fixes: a0ff4aa6f0 ("remoteproc: imx_rproc: add a NXP/Freescale imx_rproc driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-03-18 15:43:46 -07:00
Bjorn Andersson 1fb82ee806 remoteproc: qcom: Introduce sysmon
The sysmon client communicates either via a dedicated SMD/GLINK channel
or via QMI encoded messages over IPCROUTER with remote processors in
order to perform graceful shutdown and inform about other remote
processors shutting down.

Acked-By: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 16:57:22 -08:00
Bjorn Andersson 880f5b3882 remoteproc: Pass type of shutdown to subdev remove
remoteproc instances can be stopped either by invoking shutdown or by an
attempt to recover from a crash. For some subdev types it's expected to
clean up gracefully during a shutdown, but are unable to do so during a
crash - so pass this information to the subdev remove functions.

Acked-By: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 16:57:22 -08:00
Sarangdhar Joshi dcb57ed43d remoteproc: qcom: Register segments for core dump
Register MDT segments with the remoteproc core dump functionality in
order to include them in a core dump, in case of a recovery of the remote
processor.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 11:05:46 -08:00
Bjorn Andersson 4dd27f544c soc: qcom: mdt-loader: Return relocation base
In order to implement support for grabbing core dumps in remoteproc it's
necessary to know the relocated base of the image, as the offsets from
the virtual memory base might not be based on the physical address.

Return the adjusted physical base address to the caller.

Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 11:05:38 -08:00
Bjorn Andersson c1d35c1ab4 remoteproc: Rename "load_rsc_table" to "parse_fw"
The resource table is just one possible source of information that can
be extracted from the firmware file. Generalize this interface to allow
drivers to override this with parsers of other types of information.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 11:05:30 -08:00
Sarangdhar Joshi 2666ca9197 remoteproc: Add remote processor coredump support
As the remoteproc framework restarts the remote processor after a fatal
event, it's useful to be able to acquire a coredump of the remote
processor's state, for post mortem debugging.

This patch introduces a mechanism for extracting the memory contents
after the remote has stopped and before the restart sequence has begun
in the recovery path. The remoteproc framework builds the core dump in
memory and use devcoredump to expose this to user space.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
[bjorn: Use vmalloc instead of composing the ELF on the fly]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 11:05:29 -08:00
Jitendra Sharma 2d02d15804 remoteproc: Remove null character write of shared mem
remoteproc is writing '\0' in the shared mem region. This
region is shared among multiple clients that are also trying
to read. Hence they miss first character.

Remove this null character write, as this mem area is
supposed to be Read only.

Further during every subsystem reboot, this region is
initialized with default, hence no need to write this
region.

Signed-off-by: Jitendra Sharma <shajit@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 10:30:15 -08:00
Linus Torvalds 2deb41b245 remoteproc updates for v4.16
This contains a few bug fixes and a cleanup up of the resource-table handling
 in the framework, which removes the need for drivers with no resource table to
 provide a fake one.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaeJRAAAoJEAsfOT8Nma3FcwYP/jk/ubIEEF8Ne2ZRhcyT9J/2
 4sT8NJhmtHIALOlQPtKcHv766ukFtzN4Xd8fUgHiivVMOrYBbfiuO1MNXXEq2kyf
 7lWqC1eJRaa7wmlQumNw5aIOvJPuCu0oFd+K8CoKowLco32tURzJ9ANtYeXKTc/n
 KCk4KgigXRzlUP+J8TZ75Uop+N5WREGbqOHhP/J8+PYmHY+IxPN4K1CHlOBITpJz
 eLX+gs51UUKOFLGusVS5CLpUOYUc+bfWkGGeqRzMISCloSDkxdwIGuVa630VE1sJ
 QkxvvNbhQWmaaeBfplMhNHT7wHgE87c2P6mvABu5Rsf+u8V3o6JzbBW5XgxxT5uU
 QER4NRzZ/288vuOnr6FPvmR5ZZg9TaU/9Ef1vYNFEXR1uhquBmYulSbJ9FenM2up
 qQkVRQuLWYo5JLRWshVMvA0u+HGv7iA+kcGGBTfWJQgYJTG7ytmEamqoCchBOiM1
 cGOxGVkSD5tt8XBvSUx6wsmEkBqU8MGKbf77XFhYDBJNU2ZLuoETPnj2+Wjh8Myo
 5R1B0jBsWjGZ90AAXoKT2rbw2QeaADpFSneWKVbDEyTczmFDjQNZ5Qhuk1X1U3wq
 VZwmZwe2TsdaRZJhO+8SfdfspR71j2ollT1iLO2ESR5lbZZmouBm+EeW8c/ri8yW
 ei1bP8q5f2qYfSNga0hc
 =awTj
 -----END PGP SIGNATURE-----

Merge tag 'rproc-v4.16' of git://github.com/andersson/remoteproc

Pull remoteproc updates from Bjorn Andersson:
 "This contains a few bug fixes and a cleanup up of the resource-table
  handling in the framework, which removes the need for drivers with no
  resource table to provide a fake one"

* tag 'rproc-v4.16' of git://github.com/andersson/remoteproc:
  remoteproc: Reset table_ptr on stop
  remoteproc: Drop dangling find_rsc_table dummies
  remoteproc: Move resource table load logic to find
  remoteproc: Don't handle empty resource table
  remoteproc: Merge rproc_ops and rproc_fw_ops
  remoteproc: Clone rproc_ops in rproc_alloc()
  remoteproc: Cache resource table size
  remoteproc: Remove depricated crash completion
  virtio_remoteproc: correct put_device virtio_device.dev
2018-02-05 10:07:40 -08:00
Bjorn Andersson 0a8b81cb2e remoteproc: Reset table_ptr on stop
The installed resource table is no longer accessible after stopping the
remote, so update table_ptr to point to the local copy.

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:30:04 -08:00
Bjorn Andersson 4f6fd5a037 remoteproc: Drop dangling find_rsc_table dummies
As the core now deals with the lack of a resource table, remove the
dangling custom dummy implementations of find_rsc_table from drivers.

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:30:00 -08:00
Bjorn Andersson 58b6409067 remoteproc: Move resource table load logic to find
Extend the previous operation of finding the resource table in the ELF
with the extra step of populating the rproc struct with a copy and the
size. This allows drivers to override the mechanism used for acquiring
the resource table, or omit it for firmware that is known not to have a
resource table.

This leaves the custom, dummy, find_rsc_table implementations found in
some drivers dangling.

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:29:53 -08:00
Bjorn Andersson d4bb86f2c3 remoteproc: Don't handle empty resource table
Allow a NULL table_ptr to have the same meaning as a table with 0
entries, allowing a subsequent patch to skip the assignment step.

A few other places in the implementation does dereference table_ptr, but
they are currently all coming from rproc_handle_resources().

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:29:48 -08:00
Bjorn Andersson 0f21f9cc9d remoteproc: Merge rproc_ops and rproc_fw_ops
There are currently a few different schemes used for overriding fw_ops
or parts of fw_ops. Merge fw_ops into rproc_ops and expose the default
ELF-loader symbols so that they can be assigned by the drivers.

To keep backwards compatibility with the "default" case, a driver not
specifying the "load" operation is assumed to want the full ELF-loader
suit of functions.

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:29:40 -08:00
Bjorn Andersson fb98e2bdbd remoteproc: Clone rproc_ops in rproc_alloc()
In order to allow rproc_alloc() to, in a future patch, update entries in
the "ops" struct we need to make a local copy of it.

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:29:34 -08:00
Bjorn Andersson a4b24c7560 remoteproc: Cache resource table size
We don't re-read the resource table during a recovery, so it is possible
in the recovery path that the resource table has a different size than
cached_table. Store the original size of cached_table to avoid these
getting out of sync.

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:29:29 -08:00
Bjorn Andersson b26210cda6 remoteproc: Remove depricated crash completion
The crash handling now happens in a single execution context, so there's
no longer a need for a completion to synchronize this.

Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-15 09:29:16 -08:00
weiping zhang 900a163ede virtio_remoteproc: correct put_device virtio_device.dev
rproc_virtio_dev_release will be called iff virtio_device.dev's
reference count drops to 0. Here we just put vdev.dev, and then
rproc->dev's cleanup will be done in rproc_virtio_dev_release.

Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-01-02 09:32:30 -08:00
Vasyl Gomonovych a1fcc45589 remoteproc: qcom: Use PTR_ERR_OR_ZERO() in glink prob
Fix ptr_ret.cocci warnings:
drivers/remoteproc/qcom_common.c:60:8-14: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci

Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-11-28 15:02:27 -08:00
Linus Torvalds 4f88bd23ba remoteproc updates for v4.15
This adds an interface for configuring Qualcomm's "secure SMMU" and adds
 support for booting the modem Hexagon on MSM8996.
 
 Two new debugfs entries are added in the remoteproc core to introspect the list
 of memory carveouts and the loaded resource table.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaD26iAAoJEAsfOT8Nma3FUp0QAL/WZhL8QsvVFbAlv/Aa6NKm
 z8blXscD0GKdQWDWGaGPtpbnpOWOYhJs9WxstiB2q9ooSa9brIdjG5ukr4DTgtRs
 12If5tfkVFIjlBhAdYYK+biNSQtZE+37jb7aJ+j4N3Po3O72pxekcLMLhAdvY6yk
 zHnhDZ8N7KBxAa0eOg7PJz7AGRF6BHhPxkqgJm0FzBj4HLQ/lwrv6iYJRrZgw6CT
 OhIHgPwCSHmt2fTO2QDLOWJtbVMSFhunHbuYlzPwvhMAGCT87VmXCIkW8iVhcD24
 uJMrFbQoBoWVMB68JgGUKd7SSs8pV7DMrGfJll1kBEQfMLynn8Omre7WDAfwjUEn
 ACasSDWdWEPABJoIRVkGhS+2BnfCehdvDC7QxFFPAf8oc49O3t6DyXcCQdcVkzzE
 f1r/G2JKsoNQxjklFJewU5r0EjWgvV/78Dmpi7tuUtjgMSyEqkYORmInbbFIqZrU
 9bHCqrmlxuRFSklxoG2u7F2SVYgMVlqM4rmj8QqR85SeIfyZtcCx5i5yAj8dZsI1
 JVjucOCROHFqs/3SYFKlo6x4XHIchJD4p64QOXPCVhw7R1NXTPRTFBCQ75PKdiD1
 d7kcGhdaz2cMeN1WRhIQ00lh/uiDNd4Ez7sDuU8MnWiEcIs1/ZP1LCHZTNttoljH
 rWZp4XlrhT+Vx91zV5u5
 =lnNj
 -----END PGP SIGNATURE-----

Merge tag 'rproc-v4.15' of git://github.com/andersson/remoteproc

Pull remoteproc updates from Bjorn Andersson:
 "This adds an interface for configuring Qualcomm's "secure SMMU" and
  adds support for booting the modem Hexagon on MSM8996.

  Two new debugfs entries are added in the remoteproc core to introspect
  the list of memory carveouts and the loaded resource table"

* tag 'rproc-v4.15' of git://github.com/andersson/remoteproc:
  remoteproc: qcom: Fix error handling paths in order to avoid memory leaks
  remoteproc: qcom: Drop pr_err in q6v5_xfer_mem_ownership()
  remoteproc: debug: add carveouts list dump feature
  remoteproc: debug: add resource table dump feature
  remoteproc: qcom: Add support for mss remoteproc on msm8996
  remoteproc: qcom: Make secure world call for mem ownership switch
  remoteproc: qcom: refactor mss fw image loading sequence
  firmware: scm: Add new SCM call API for switching memory ownership
2017-11-17 20:14:10 -08:00
Linus Torvalds bedf571986 rpmsg updates for v4.15
This turn RPMSG_VIRTIO into a user selectable config, fixes a few bugs in GLINK
 and provides the support for specifying initial buffer sizes for GLINK
 channels.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaD2r+AAoJEAsfOT8Nma3F/tMP/24c6KyWfmkhRYXA5gJmEjnD
 PpzhfNonTYl225ZRutR6M4+gpOt6Ljtu8gvGzqXuPRNBf4CNCMqTRvQt0nF+jZnw
 QciY3dtDMKdCGC3hZoxCX6d1GjjtqvPL4SJW4zkcgYw4SnN5nISFw9iHpdDcX5bx
 RoCcCzq7rPRBRs4HNQ7wDSFTh9UAr5tAY5i4HwsAAoGejlhhioduDWoLp4dgGV5j
 Nc7wOU8KQZzPivN/i9ma8WdjZDzy9oSz0PRF6nbGnvFp/NOlxA3rj1DVIB7ONaV0
 Ttod4Fs5Mj1GrsBKQ4rf2qVwjTIM2x721wJDBAzqJ6fRtHwCFim2THMZPx0s7pa9
 SqX+ZUmV9WD8TBz+mQcLYG3mHqZIlpE4f+uAc8XWruISyij7j9QVoqzZxtGRI1H/
 SFu21ovlZieuBRS3g8soxkjFmHzlvvyzrv8p/+t4KqAtb1csTVPAxEsT8PddHzPR
 +c8mUKgFlcJnmi4ILg3rIo7Z3BLfz7C7jIZpRBXEe2Z2JA1aHbUrUWDpw/QhHoEy
 rlASk0f4h4uhAYlsxJDYx+Wg5b3DV0H/ouy5qzDdxlB78Gvw+6/2RUPSeummu2Mt
 5rKg0anw1GtAGYlXx14HVX427HY3y6mrmNERlfPnwkwfQfTbYVQ6vMp1op+8XF0H
 KbxkyufQlZnimLJjwD6W
 =jirb
 -----END PGP SIGNATURE-----

Merge tag 'rpmsg-v4.15' of git://github.com/andersson/remoteproc

Pull rpmsg updates from Bjorn Andersson:

 - turn RPMSG_VIRTIO into a user selectable config

 - fix few bugs in GLINK

 - provide the support for specifying initial buffer sizes for GLINK
   channels.

* tag 'rpmsg-v4.15' of git://github.com/andersson/remoteproc:
  rpmsg: glink: The mbox client knows_txdone
  rpmsg: glink: Add missing MODULE_LICENSE
  rpmsg: glink: Use best fit intent during tx
  rpmsg: glink: Add support to preallocate intents
  dt-bindings: soc: qcom: Support GLINK intents
  rpmsg: glink: Initialize the "intent_req_comp" completion variable
  rpmsg: Allow RPMSG_VIRTIO to be enabled via menuconfig or defconfig
2017-11-17 20:12:08 -08:00
Christophe JAILLET 1a5d5c592e remoteproc: qcom: Fix error handling paths in order to avoid memory leaks
In case of error returned by 'q6v5_xfer_mem_ownership', we must free
some resources before returning.

In 'q6v5_mpss_init_image()', add a new label to undo a previous
'dma_alloc_attrs()'.
In 'q6v5_mpss_load()', re-use the already existing error handling code to
undo a previous 'request_firmware()', as already done in the other error
handling paths of the function.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-11-14 23:20:11 -08:00
Bjorn Andersson 9f2a4342a8 remoteproc: qcom: Drop pr_err in q6v5_xfer_mem_ownership()
The pr_err() in q6v5_xfer_mem_ownership() prints, upon failure, the
memory range that failed to be transitioned. But on 32-bit architectures
with CONFIG_PHYS_ADDR_T_64BIT set we cannot cast the phys_addr_t
variable to a pointer, per below build error. Instead these should be
formatted with %pap.

In file included from include/linux/kernel.h:14:0,
                 from include/linux/clk.h:16,
                 from drivers/remoteproc/qcom_q6v5_pil.c:18:
drivers/remoteproc/qcom_q6v5_pil.c: In function 'q6v5_xfer_mem_ownership':
drivers/remoteproc/qcom_q6v5_pil.c:337:10: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
          (void *)addr, (void *)(addr + size),
          ^

Most callers will upon failure print a specific error message describing
which memory region that we failed to pass ownership of, so rather than
fixing the format string this patch fixes up the last callers and drop
the print from this function, saving us from spamming the log in most of
these error cases.

Fixes: 6c5a9dc248 ("remoteproc: qcom: Make secure world call for mem ownership switch")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-11-06 22:37:39 -08:00
Loic Pallardy b891883941 remoteproc: debug: add carveouts list dump feature
This patch offers the capability to dump memory carveouts associated
to one remoteprocessor.

Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-11-06 21:57:27 -08:00
Loic Pallardy bdd8edb9b0 remoteproc: debug: add resource table dump feature
This patch adds the capability to display the content of
the resource table associated to a remote processor firmware.

Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-11-06 21:57:21 -08:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Avaneesh Kumar Dwivedi 9f058fa2ef remoteproc: qcom: Add support for mss remoteproc on msm8996
This patch add support for mss boot on msm8996. Major changes
include initializing mss rproc for msm8996, making appropriate
change for executing mss reset sequence etc.

Tested-and-acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-10-30 18:37:23 -07:00
Avaneesh Kumar Dwivedi 6c5a9dc248 remoteproc: qcom: Make secure world call for mem ownership switch
MSS proc on msm8996 can not access fw loaded region without stage
second translation of memory pages where mpss image are loaded.
This patch in order to enable mss boot on msm8996 invoke scm call
to switch or share ownership between apps and modem.

Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
[bjorn: Corrected error path in q6v5_start()]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-10-30 18:37:22 -07:00
Avaneesh Kumar Dwivedi 94c907859a remoteproc: qcom: refactor mss fw image loading sequence
This patch refactor code to first load all firmware blobs
and then update modem proc to authenticate and boot fw.

Tested-and-acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-10-30 18:37:22 -07:00
Anup Patel 4d91d7b099 rpmsg: Allow RPMSG_VIRTIO to be enabled via menuconfig or defconfig
Currently, RPMSG_VIRTIO can only be enabled if some other kconfig
option selects it. This does not allow it to be enabled for
virtualized systems where Virtio RPMSG is available over Virtio
MMIO or PCI transport.

This patch updates RPMSG_VIRTIO kconfig option so that we can
enable the VirtIO RPMSG driver via menuconfig or defconfig. The
patch also removes "select RPMSG_VIRTIO" from various remoteproc
kconfig options because it is now user selectable.

Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-10-25 21:51:05 -07:00
Wei Yongjun 68a39a3e9f remoteproc: imx_rproc: fix return value check in imx_rproc_addr_init()
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.

Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-10-11 10:47:47 -07:00
Arnd Bergmann ab759b9732 remoteproc: qcom: fix RPMSG_QCOM_GLINK_SMEM dependencies
When RPMSG_QCOM_GLINK_SMEM=m and one driver causes the qcom_common.c file
to be compiled as built-in, we get a link error:

drivers/remoteproc/qcom_common.o: In function `glink_subdev_remove':
qcom_common.c:(.text+0x130): undefined reference to `qcom_glink_smem_unregister'
qcom_common.c:(.text+0x130): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_glink_smem_unregister'
drivers/remoteproc/qcom_common.o: In function `glink_subdev_probe':
qcom_common.c:(.text+0x160): undefined reference to `qcom_glink_smem_register'
qcom_common.c:(.text+0x160): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_glink_smem_register'

Out of the three PIL driver instances, QCOM_ADSP_PIL already has a
Kconfig dependency to prevent this from happening, but the other two
do not. This adds the same dependency there.

Fixes: eea07023e6 ("remoteproc: qcom: adsp: Allow defining GLINK edge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-10-10 11:28:20 -07:00
Dan Carpenter 68c2d645eb remoteproc: imx_rproc: fix a couple off by one bugs
The priv->mem[] array has IMX7D_RPROC_MEM_MAX elements so the > should
be >= to avoid writing one element beyond the end of the array.

Fixes: a0ff4aa6f0 ("remoteproc: imx_rproc: add a NXP/Freescale imx_rproc driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-10-10 11:22:55 -07:00
Linus Torvalds 7151202b64 rpmsg updates for v4.14
This extends the Qualcomm GLINK implementation to support the additional
 features used for communicating with modem and DSP coprocessors in modern
 Qualcomm platforms.
 
 In addition to this there's support for placing virtio RPMSG buffers in
 non-System RAM.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZswd9AAoJEAsfOT8Nma3FSigQALyq2wNtf60tkTKW0f2K8cM6
 JpnEKAKqO1t5ZkokEevT05PLT4rqXuidrDVOBJ3VQ7LtSqJOiTjGyN9YM8t+WBVG
 ts0Yg69+wUxBATg9iM2JiUsKn8gH8swUAtf16dmkL/Ca8BJKOHGYTUjADfwuFrEg
 EAGcLZnlwz736xdo9qZu/Ke9rItz6CDOD3AphbpJbcv7Wj2F/mEuqMZjfLk+1Mo8
 C3wXx9jIzW1siNtT0OY9raUNV5gLaGS2zZ+DYwrwjND7Eh0TqeLxyJ1OS7f2kOZ5
 P6zcrYw02WbDVW7LUzVegj5PejZm/wdFZ5hSvishEfZZVT+wGHBK34mfObe0moJZ
 Wp8jFSXKqECIEU3x/2DtPAHi+mittDpQ3FCkElWKJRD6B3HTySHjvM0lOor+zYKB
 gRX4QUR6jwkSRAbV6GP24Z8SL9kU6TXOSoOQvuzuKhB30JzADJPuQnGZR0SftYiH
 YJG/RT9FklbljWP9hIgey3QPNHPoL3IzNBU2iyEjdraabmNaFEb++wpLdpCZdnGf
 1HMLrMfUmd3QKRtXvT+5Q6CjnfzwFk1ii1naN3Ky9rar3WRtij5bzo8eveR8i9ag
 DtWA88N9mnpSUao14o5vKN830q3/fkwW6HyT0nCd59Wq94cMNfiMdFPVXvO0xVAF
 mjP4JXHbqNhdJySWR4Du
 =PVGN
 -----END PGP SIGNATURE-----

Merge tag 'rpmsg-v4.14' of git://github.com/andersson/remoteproc

Pull rpmsg updates from Bjorn Andersson:
 "This extends the Qualcomm GLINK implementation to support the
  additional features used for communicating with modem and DSP
  coprocessors in modern Qualcomm platforms.

  In addition to this there's support for placing virtio RPMSG buffers
  in non-System RAM"

* tag 'rpmsg-v4.14' of git://github.com/andersson/remoteproc: (29 commits)
  rpmsg: glink: initialize ret to zero to ensure error status check is correct
  rpmsg: glink: fix null pointer dereference on a null intent
  dt-bindings: soc: qcom: Extend GLINK to cover SMEM
  remoteproc: qcom: adsp: Allow defining GLINK edge
  rpmsg: glink: Export symbols from common code
  rpmsg: glink: Release idr lock before returning on error
  rpmsg: glink: Handle remote rx done command
  rpmsg: glink: Request for intents when unavailable
  rpmsg: glink: Use the intents passed by remote
  rpmsg: glink: Receive and store the remote intent buffers
  rpmsg: glink: Add announce_create ops and preallocate intents
  rpmsg: glink: Add rx done command
  rpmsg: glink: Make RX FIFO peak accessor to take an offset
  rpmsg: glink: Use the local intents when receiving data
  rpmsg: glink: Add support for TX intents
  rpmsg: glink: Fix idr_lock from mutex to spinlock
  rpmsg: glink: Add support for transport version negotiation
  rpmsg: glink: Introduce glink smem based transport
  rpmsg: glink: Do a mbox_free_channel in remove
  rpmsg: glink: Return -EAGAIN when there is no FIFO space
  ...
2017-09-09 14:34:38 -07:00
Bjorn Andersson 7c89717f82 remoteproc: Introduce rproc handle accessor for children
In certain circumstances rpmsg devices needs to acquire a handle to the
ancestor remoteproc instance, e.g. to invoke rproc_report_crash() when a
fatal error is detected. Introduce an interface that walks the device
tree in search for a remoteproc instance and return this.

Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-09-01 15:49:13 -07:00
Bjorn Andersson 4fec0a5a19 remoteproc: qcom: Make ssr_notifiers local
The ssr_notifiers variable should be local, so add the missing static
storage classifier.

Fixes: 1e140df049 ("remoteproc: qcom: Add support for SSR notifications")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-09-01 15:42:29 -07:00
Bjorn Andersson eea07023e6 remoteproc: qcom: adsp: Allow defining GLINK edge
Introduce the GLINK subdev, which allows the definition of a GLINK edge
as child of a remoteproc.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-09-01 15:31:23 -07:00
Bjorn Andersson f9cbbd256c remoteproc: Stop subdevices in reverse order
Subdevices might depend on earlier registered subdevices for
communication purposes, as such they should be stopped in reverse order
so that said communication channel is removed after the dependent
subdevice is stopped.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-30 16:29:55 -07:00
Oleksij Rempel a0ff4aa6f0 remoteproc: imx_rproc: add a NXP/Freescale imx_rproc driver
Provide a basic driver to control Cortex M4 co-processor found
on NXP i.MX7D and i.MX6SX.
Currently it is able to resolve addresses between M4 and main CPU,
start and stop the co-processor. Other functionality is not provided
or test.

This driver was tested on NXP i.MX7D and expected to work on
i.MX6SX as well.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-30 16:07:41 -07:00
Himanshu Jha c76929b3c6 remoteproc: qcom: Use PTR_ERR_OR_ZERO
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-29 15:34:19 -07:00
Philipp Zabel 1e13c7fb49 remoteproc: st: explicitly request exclusive reset control
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-27 23:18:52 -07:00
Philipp Zabel 5acbf7e520 remoteproc: qcom: explicitly request exclusive reset control
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-27 23:18:35 -07:00
Philipp Zabel f5f98654a2 remoteproc/keystone: explicitly request exclusive reset control
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-27 23:16:22 -07:00
Suman Anna b4daf89057 remoteproc/keystone: Add support for Keystone 66AK2G SOCs
Add support to the keystone remoteproc driver for managing the
DSP present in the Keystone 2 66AK2G SoC. The 66AK2G SoC has
a Power Management Micro Controller (PMMC) that manages the
individual device's power, clock and reset functionalities.

The keystone remoteproc driver already uses standard frameworks
for reset and clock control, so it doesn't require any significant
modifications other than a new compatible suitable for 66AK2G DSP.

The binding document is also updated to reflect the modified
property values used by the 66AK2G DSP node as compared to the
values used by existing Keystone 2 DSPs.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-24 12:01:29 -07:00
Suman Anna 616965805f remoteproc/davinci: Add device tree support for OMAP-L138 DSP
The Davinci remoteproc driver currently supports the DSP remoteproc
device created in legacy-style on OMAP-L13x SoCs. The driver has been
enhanced to support the DSP remoteproc device created through Device
Tree now. The current DT support handles the C674x DSP processor
subsystem on OMAP-L138 SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-24 12:00:21 -07:00
Suman Anna 59b2355fc9 remoteproc/davinci: Add support to parse internal memories
The DSP subsystem on OMAP-L13x SoCs has various internal RAM
memories that can accessed from the ARM side. These memories
can be configured to be used as either RAM or Cache.

The Davinci remoteproc driver has been enhanced to parse and
store the kernel mappings for these internal RAM memories.
These mappings can then be used to support direct loading of
text/data into these memories from the remoteproc driver.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-24 11:59:55 -07:00
Suman Anna 6fb9a8f5ad remoteproc/davinci: Switch to platform_get_resource_byname()
The davinci remoteproc driver currently uses the platform_get_resource()
API for retrieving the IOMEM resources. Switch this function to use the
platform_get_resource_byname() API instead in preparation for adding the
DT support so that the binding can be agnostic of the IOMEM resource
order.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-24 11:59:53 -07:00
Bhumika Goyal c42ca04da5 remoteproc: make device_type const
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-24 10:25:50 -07:00
Bjorn Andersson 1e140df049 remoteproc: qcom: Add support for SSR notifications
This adds the remoteproc part of subsystem restart, which is responsible
for emitting notifications to other processors in the system about a
dying remoteproc instance.

These notifications are propagated to the various communication systems
in the various remote processors to shut down communication links that
was left in a dangling state as the remoteproc was stopped (or crashed).

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-08-02 12:43:20 -07:00
Suman Anna 1b0ef9068f remoteproc: Merge __rproc_boot() with rproc_boot()
The additional arguments in the internal __rproc_boot() function
were dropped in commit 2bfc311a57 ("remoteproc: Drop wait in
__rproc_boot()"). The exported rproc_boot() is now just a wrapper
around this internal function, so merge them together.

While at this, also remove the declaration for the previously
cleaned up rproc_boot_nowait() function.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-07-26 10:01:27 -07:00
Suman Anna b0af7b7dbe remoteproc/keystone: Fix circular dependencies for ARM configs
Drop the dependency on RESET_CONTROLLER for the Keystone remoteproc
driver to resolve some circular dependencies around different choices
for RESET_CONTROLLER on common ARM configs. This dependency is
inherent as the RESET_CONTROLLER will be enabled due to the enabled
ARCH_HAS_RESET_CONTROLLER for ARCH_KEYSTONE.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-27 16:21:34 -07:00
Suman Anna e3f37c5ed7 remoteproc: Drop redundant REMOTEPROC dependency from driver Kconfigs
All the remoteproc platform driver Kconfig symbols are defined and
included under an if REMOTEPROC condition, so the dependency on
REMOTEPROC is implicit and they do not need an explicit 'depends
on REMOTEPROC' line. So, clean these up.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-27 16:01:14 -07:00
Suman Anna 384700d465 remoteproc: Drop VIRTUALIZATION dependency from REMOTEPROC
A dependency to VIRTUALIZATION has been added to REMOTEPROC in v3.10
kernel in commit b9777859ec ("remoteproc: fix kconfig dependencies
for VIRTIO") to resolve Kconfig warnings due to the inclusion of the
virtio configuration file from the ARM's KVM config file. The KVM
config was fixed properly in the subsequent release in commit
8bd4ffd6b3 ("ARM: kvm: don't include drivers/virtio/Kconfig").
So, drop this unneeded VIRTUALIZATION dependency from REMOTEPROC.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-27 16:01:00 -07:00
Andrew F. Davis 11d2a2ffa8 remoteproc/keystone: Ensure the DSPs are in reset in probe
The DSPs are expected to be in reset when the driver probes a device.
If the DSPs are out of reset in probe, the system may crash when the
firmware is being loaded. So, add a check to make sure the DSP resets
are asserted, and if not, throw a eye-catchy warning and assert the
resets specifically.

Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: replace warning with a WARN]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-26 13:02:44 -07:00
Suman Anna e88bb8f7a1 remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs
The Texas Instrument's Keystone 2 family of SoCs has 1 or more
TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
that can be configured and partitioned as either RAM and/or Cache,
and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC)
with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).

A new remoteproc module is added to perform the device management of
these DSP devices. The driver expects the firmware names to be of the
form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
uses the standard remoteproc core ELF loader. The support is limited
to images only using the DSP internal memories at the moment. This
remoteproc driver is also designed to work with virtio, and uses the
IPC Generation registers for performing the virtio signalling and
getting notified of exceptions.

The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-26 13:02:38 -07:00
Suman Anna a63c70d4dc remoteproc/davinci: fix unbalanced reset between start and stop ops
The davinci remoteproc driver is currently de-asserting the reset in
its rproc .start() ops, but is not asserting the reset in its .stop()
ops. This leaves the remote processor to not boot properly when using
the sysfs 'state' variable between multiple start and stop operations.
On the other hand, a reset is being asserted unconditionally in the
driver remove function to alleviate some of these issues.

Move this reset assertion logic into the .stop() ops implementation
to fix the sysfs state-machine and the unbalanced reset. The logic
from remove is still effective since .stop() ops will be invoked
during the remove due to the enabled 'auto-boot' support. The probe
already has support for asserting the reset in case the DSP is not
in reset for some reason.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-25 14:00:54 -07:00
Suman Anna 470ac62fe5 remoteproc/davinci: simplify the reset function
The reset_assert() function is used to make sure the DSP remote
processor is in a reset state regardless of its previous state.
The driver relies on davinci_clk_reset_{assert,deassert}()
functions for reset management which take in a clock parameter.
The assert_reset() performs a clk_get()/clk_put() cycle to
acquire the clock handle to use with this function. This is
totally unnecessary and the code can be simplified to use
the clock acquired during probe and directly use the reset
functions, so simplify this logic.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-25 14:00:00 -07:00
Suman Anna c51e882cd7 remoteproc/davinci: Update Kconfig to depend on DMA_CMA
The davinci remoteproc driver requires a CMA pool for allocating
memory for virtio vrings/buffers and other sections of the firmware
image. The allocations are done using the DMA API. The CMA option is
currently selected automatically on systems with MMU when davinci
remoteproc is enabled, switch this to a saner depends on dependency
convention. The dependency is also updated to use the DMA_CMA kconfig
symbol that is used for CMA allocations using the DMA API, the CMA
dependency is inherited implicitly.

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-25 13:59:58 -07:00
Colin Ian King ca91ab5f11 remoteproc: fix spelling mistake: "Resouce" -> "Resource"
Trivial fix to spelling mistake in dev_err message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-05-30 20:57:40 -07:00
Sarangdhar Joshi 7e83cab824 remoteproc: Modify recovery path to use rproc_{start,stop}()
Replace rproc_shutdown() by rproc_stop() and rproc_boot() by
rproc_start() in the recovery path, in order to avoid remoteproc
resources re-allocation overhead and to assist with extracting the
coredumps after stopping the remote processor.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-05-26 18:11:33 -07:00
Sarangdhar Joshi 1efa30d089 remoteproc: Introduce rproc_{start,stop}() functions
In the context of recovering from crash, rproc_trigger_recovery() does
rproc_shutdown() followed by rproc_boot(). The remoteproc resources are
cleaned up in rproc_shutdown() and immediately reallocated in
rproc_boot() which is an unnecessary overhead. Furthermore, we want the
memory regions to be accessible after stopping the remote processor, to
be able to extract the memory content for a coredump.

This patch factors out the code in rproc_boot() and rproc_shutdown()
path and introduces rproc_{start,stop}() in order to avoid resource
allocation overhead.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-05-26 18:11:31 -07:00
Linus Torvalds c44b594303 virtio: fixes, cleanups, performance
A bunch of changes to virtio, most affecting virtio net.
 ptr_ring batched zeroing - first of batching enhancements
 that seems ready.
 
 Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
 -----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJZEceWAAoJECgfDbjSjVRpg8YIAIbB1UJZkrHh/fdCQjM2O53T
 ESS62W91LBT+weYH/N79RrfnGWzDOHrCQ8Or1nAKQZx2vU1aroqYXeJ9o0liRBYr
 hGZB1/bg8obA5XkKUfME2+XClakvuXABUJbky08iDL9nILlrvIVLoUgZ9ouL0vTj
 oUv4n6jtguNFV7tk/injGNRparEVdcefX0dbPxXomx5tSeD2fOE96/Q4q2eD3f7r
 NHD4DailEJC7ndJGa6b4M9g8shkXzgEnSw+OJHpcJcxCnAzkVT94vsU7OluiDvmG
 bfdGZNb0ohDYZLbJDR8aiMkoad8bIVLyGlhqnMBiZQEOF4oiWM9UJLvp5Lq9g7A=
 =Sb7L
 -----END PGP SIGNATURE-----

Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost

Pull virtio updates from Michael Tsirkin:
 "Fixes, cleanups, performance

  A bunch of changes to virtio, most affecting virtio net. Also ptr_ring
  batched zeroing - first of batching enhancements that seems ready."

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  s390/virtio: change maintainership
  tools/virtio: fix spelling mistake: "wakeus" -> "wakeups"
  virtio_net: tidy a couple debug statements
  ptr_ring: support testing different batching sizes
  ringtest: support test specific parameters
  ptr_ring: batch ring zeroing
  virtio: virtio_driver doc
  virtio_net: don't reset twice on XDP on/off
  virtio_net: fix support for small rings
  virtio_net: reduce alignment for buffers
  virtio_net: rework mergeable buffer handling
  virtio_net: allow specifying context for rx
  virtio: allow extra context per descriptor
  tools/virtio: fix build breakage
  virtio: add context flag to find vqs
  virtio: wrap find_vqs
  ringtest: fix an assert statement
2017-05-10 11:33:08 -07:00
Michael S. Tsirkin f94682dde5 virtio: add context flag to find vqs
Allows maintaining extra context per vq.  For ease of use, passing in
NULL is legal and disables the feature for all vqs.

Includes fixes by Christian for s390, acked by Cornelia.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2017-05-02 23:41:43 +03:00
Bjorn Andersson 395a48053a soc: qcom: smd: Remove standalone driver
Remove the standalone SMD implementation as we have transitioned the
client drivers to use the RPMSG based one.

Also remove all dependencies on QCOM_SMD from Kconfig files, in order to
keep them selectable in the absence of the removed symbol.

Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-28 17:58:07 -07:00
Arnd Bergmann c3104aae5d remoteproc: qcom: fix QCOM_SMD dependencies
qcom_smd_register_edge() is provided by either QCOM_SMD or RPMSG_QCOM_SMD,
and if both of them are disabled, it does nothing.

The check for the PIL drivers however only checks for QCOM_SMD, so it breaks
with QCOM_SMD=n && RPMSG_QCOM_SMD=m:

drivers/remoteproc/built-in.o: In function `smd_subdev_remove':
qcom_wcnss_iris.c:(.text+0x231c): undefined reference to `qcom_smd_unregister_edge'
drivers/remoteproc/built-in.o: In function `smd_subdev_probe':
qcom_wcnss_iris.c:(.text+0x2344): undefined reference to `qcom_smd_register_edge'
drivers/remoteproc/built-in.o: In function `smd_subdev_probe':
qcom_q6v5_pil.c:(.text+0x3538): undefined reference to `qcom_smd_register_edge'
qcom_q6v5_pil.c:(.text+0x3538): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_smd_register_edge'

This clarifies the Kconfig dependency.

Fixes: 4b48921a8f ("remoteproc: qcom: Use common SMD edge handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-03-20 14:45:44 -07:00
Linus Torvalds 54d7989f47 virtio, vhost: optimizations, fixes
Looks like a quiet cycle for vhost/virtio, just a couple of minor
 tweaks. Most notable is automatic interrupt affinity for blk and scsi.
 Hopefully other devices are not far behind.
 
 Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
 -----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJYt1rRAAoJECgfDbjSjVRpEZsIALSHevdXWtRHBZUb0ZkqPLQb
 /x2Vn49CcALS1p7iSuP9L027MPeaLKyr0NBT9hptBChp/4b9lnZWyyAo6vYQrzfx
 Ia/hLBYsK4ml6lEwbyfLwqkF2cmYCrZhBSVAILifn84lTPoN7CT0PlYDfA+OCaNR
 geo75qF8KR+AUO0aqchwMRL3RV3OxZKxQr2AR6LttCuhiBgnV3Xqxffg/M3x6ONM
 0ffFFdodm6slem3hIEiGUMwKj4NKQhcOleV+y0fVBzWfLQG9210pZbQyRBRikIL0
 7IsaarpaUr7OrLAZFMGF6nJnyRAaRrt6WknTHZkyvyggrePrGcmGgPm4jrODwY4=
 =2zwv
 -----END PGP SIGNATURE-----

Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost

Pull vhost updates from Michael Tsirkin:
 "virtio, vhost: optimizations, fixes

  Looks like a quiet cycle for vhost/virtio, just a couple of minor
  tweaks. Most notable is automatic interrupt affinity for blk and scsi.
  Hopefully other devices are not far behind"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio-console: avoid DMA from stack
  vhost: introduce O(1) vq metadata cache
  virtio_scsi: use virtio IRQ affinity
  virtio_blk: use virtio IRQ affinity
  blk-mq: provide a default queue mapping for virtio device
  virtio: provide a method to get the IRQ affinity mask for a virtqueue
  virtio: allow drivers to request IRQ affinity when creating VQs
  virtio_pci: simplify MSI-X setup
  virtio_pci: don't duplicate the msix_enable flag in struct pci_dev
  virtio_pci: use shared interrupts for virtqueues
  virtio_pci: remove struct virtio_pci_vq_info
  vhost: try avoiding avail index access when getting descriptor
  virtio_mmio: expose header to userspace
2017-03-02 13:53:13 -08:00
Christoph Hellwig fb5e31d970 virtio: allow drivers to request IRQ affinity when creating VQs
Add a struct irq_affinity pointer to the find_vqs methods, which if set
is used to tell the PCI layer to create the MSI-X vectors for our I/O
virtqueues with the proper affinity from the start.  Compared to after
the fact affinity hints this gives us an instantly working setup and
allows to allocate the irq descritors node-local and avoid interconnect
traffic.  Last but not least this will allow blk-mq queues are created
based on the interrupt affinity for storage drivers.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2017-02-27 20:54:04 +02:00
Bjorn Andersson 01625cc5e6 remoteproc: qcom: mdt_loader: Use signed type for offset
In the transition from using rproc_da_to_va(), the type of the load
offset became unsigned. This causes the subsequent check to let negative
values less than p_memsz + mem_size through and we write outside of the
buffer.

Change the type back to a signed value to catch this.

Fixes: 7f0dd07a9b ("remoteproc: qcom: mdt_loader: Refactor MDT loader")
Fixes: e7fd252262 ("remoteproc: qcom: q6v5: Decouple driver from MDT loader")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-22 02:07:13 -08:00
Loic Pallardy 231c8dfd1a remoteproc: st: add virtio communication support
This patch provides virtio communication support based on mailbox
for ST co-processors.

Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 13:10:12 -08:00
Loic Pallardy 3e49ecf6b4 remoteproc: st: correct probe error management
Associated clock is prepared in st_rproc_parse_dt function.
it should be unprepared in case of error during probing.

Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 13:09:01 -08:00
Sarangdhar Joshi 5e6533f72c remoteproc: Modify the function names
The functions rproc_add_virtio_devices() and rproc_fw_config_virtio()
are reduced to trigger auto-boot only. Modify these function names and
related comments to reflect their current state.

This patch does not add any functional change.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 13:06:13 -08:00
Sarangdhar Joshi 7a20c64ddb remoteproc: Reduce asynchronous request_firmware to auto-boot only
The rproc_add_virtio_devices() requests firmware asynchronously and
triggers boot if the auto_boot flag is set. However, this
asynchronous call seems to be redundant for non auto-boot scenario
since the rproc_boot() would call request_firmware() anyways. Move
the auto_boot check to rproc_add() so that a redundant call to
_request_firmware can be avoided for non auto-boot case.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 13:05:22 -08:00
Sarangdhar Joshi 66a66aa74e remoteproc: Drop qcom_scm_pas_supported() from adsp_probe()
SCM call to check whether Peripheral Authentication Service (PAS) is
supported returns false for ADSP on MSM8996. Drop this call from the
driver so that the probe() function succeeds for ADSP PIL device.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 12:45:21 -08:00
Bjorn Andersson 4b48921a8f remoteproc: qcom: Use common SMD edge handler
Call the common SMD edge handler to instantiate subdevices to bring
associated SMD edges up and down as the remoteproc is started and
stopped.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:57:25 -08:00
Bjorn Andersson b90fcfcb13 remoteproc: qcom: wcnss: Make SMD handling common
Move the SMD edge handling to the Qualcomm common file to make it
reusable for other Qualcomm remoteproc drivers.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:57:25 -08:00
Bjorn Andersson 2aad40d911 remoteproc: Move qcom_mdt_loader into drivers/soc/qcom
With the remoteproc parts cleaned out of the MDT loader we can move it
to drivers/soc/qcom.

Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:57:25 -08:00
Bjorn Andersson 7f0dd07a9b remoteproc: qcom: mdt_loader: Refactor MDT loader
Pushing the SCM calls into the MDT loader reduces duplication in the
callers and allows for non-remoteproc clients to use the helper for
parsing and loading MDT files.

Cc: Andy Gross <andy.gross@linaro.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:57:24 -08:00
Bjorn Andersson 3e8b571a9a remoteproc: qcom: mdt_loader: Don't overwrite firmware object
The "fw" firmware object is passed from the remoteproc core and should
not be overwritten, as that results in leaked buffers and a double free
of the the last firmware object.

Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:57:24 -08:00
Bjorn Andersson bde440eee2 remoteproc: qcom: Extract non-mdt related helper
In preparation for moving the mdt loader out of remoteproc let's move
the somewhat unrelated resource table dummy helper to a Qualcomm
"common" file.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:57:24 -08:00
Bjorn Andersson e7fd252262 remoteproc: qcom: q6v5: Decouple driver from MDT loader
Rather than duplicating half of the MDT loader in the validation step
move the entire MDT parser into the q6v5 driver. This allows us to make
the shared MDT-loader call the SCM PAS operations directly which
simplifies the client code and allows for better reuse of the code.

Cc: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:57:19 -08:00
Bjorn Andersson 2bb5d90699 remoteproc: qcom: q6v5: Remove mss supply from 8916
The Q6V5 in MSM8916 doesn't have a mss supply, so remove this and update
the code to support cases without proxy or active supplies.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-06 08:25:02 -08:00
Arnd Bergmann ec671b5360 remoteproc: qcom: fix initializers for qcom_mss_reg_res array
The recently added initialization is rather unusual because it uses a constructor for
a variable-length array to assign a constant structure to a member that uses a fixed-length
array. This confuses clang and breaks the build.

drivers/remoteproc/qcom_q6v5_pil.c:1024:18: error: incompatible pointer types initializing 'const char *' with an expression of type
:%s      'struct qcom_mss_reg_res [4]' [-Werror,-Wincompatible-pointer-types]
        .proxy_supply = (struct qcom_mss_reg_res[]) {
                        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/remoteproc/qcom_q6v5_pil.c:1024:18: warning: suggest braces around initialization of subobject [-Wmissing-braces]
        .proxy_supply = (struct qcom_mss_reg_res[]) {
                        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We can either turn this constructor into a regular initializer by removing
the 'struct qcom_mss_reg_res[])', or we can make the array variable length.

The latter approach is used for the arrays of strings in the same structure,
so let's use that here too.

Fixes: 19f902b53b ("remoteproc: qcom: Initialize and enable proxy and active regulators.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-02-01 01:22:21 -08:00
Sarangdhar Joshi 2099c77d4a remoteproc: Drop firmware_loading_complete
firmware_loading_complete is used to synchronize operations
on rproc while asynchronous firmware loading is in progress.
However, rproc_boot() no longer waits on
firmware_loading_complete. Hence drop this completion
variable altogether and handle the race between rproc_del()
and rproc_boot() using new state RPROC_DELETED.

The request_firmware_nowait() will hold the reference to
rproc device by using a get_device()/put_device(), so the
rproc struct will remain valid even when we return from
rproc_del() before the asynchronous call to
rproc_fw_config_virtio() completes.

CC: Loic Pallardy <loic.pallardy@st.com>
CC: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-01-30 14:18:54 -08:00