Some error paths leave the bus id allocated. As a result the IDR
allocation will fail after a deferred probe. Fix by freeing the bus id
always on error.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Message-Id: <20200304111740.27915-1-aaro.koskinen@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There maybe an overshoot, when disabling, then re-enabling vrefbuf
too quickly. VREFBUF is used by ADC/DAC on some boards. When re-enabling
too quickly, an overshoot on the reference voltage make the conversions
inaccurate for a short period of time.
- Don't put the VREFBUF in HiZ when disabling, to force an active
discharge.
- Enforce a 1ms OFF/ON delay
Fixes: 0cdbf481e9 ("regulator: Add support for stm32-vrefbuf")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Message-Id: <1583312132-20932-1-git-send-email-fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit ff57c65138.
With the commit ff57c65138 ("drm: kirin: Fix for hikey620
display offset problem") we added support for handling LDI
overflows by resetting the hardware.
However, its been observed that when we do hit the LDI overflow
condition, the irq seems to be screaming, and we do nothing but
stream:
[drm:ade_irq_handler [kirin_drm]] *ERROR* LDI underflow!
over and over to the screen
I've tried a few appraoches to avoid this, but none has yet
been successful and the cure here is worse then the original
disease, so revert this for now.
Cc: Xinliang Liu <xinliang.liu@linaro.org>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Fixes: ff57c65138 ("drm: kirin: Fix for hikey620 display offset problem")
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303163228.52741-1-john.stultz@linaro.org
The commit e894efef9a ("ASoC: core: add support to card rebind")
allows to rebind the sound card after a rebind of one of its component.
With this commit, the sound card is actually rebound,
but may be no more functional. The following problems have been seen
with STM32 SAI driver.
1) DMA channel is not requested:
With the sound card rebind the simplified call sequence is:
stm32_sai_sub_probe
snd_soc_register_component
snd_soc_try_rebind_card
snd_soc_instantiate_card
devm_snd_dmaengine_pcm_register
The problem occurs because the pcm must be registered,
before snd_soc_instantiate_card() is called.
Modify SAI driver, to change the call sequence as follows:
stm32_sai_sub_probe
devm_snd_dmaengine_pcm_register
snd_soc_register_component
snd_soc_try_rebind_card
2) DMA channel is not released:
dma_release_channel() is not called when
devm_dmaengine_pcm_release() is executed.
This occurs because SND_DMAENGINE_PCM_DRV_NAME component,
has already been released through devm_component_release().
devm_dmaengine_pcm_release() should be called before
devm_component_release() to avoid this problem.
Call snd_dmaengine_pcm_unregister() and snd_soc_unregister_component()
explicitly from SAI driver, to have the right sequence.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Message-Id: <20200304102406.8093-1-olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bunch of busy work is done for devices that don't have sync_state()
support. Stop doing the busy work.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20200221080510.197337-4-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial patch that added sync_state() support didn't handle the case
where a supplier has no consumers. This was because when a device is
successfully bound with a driver, only its suppliers were checked to see
if they are eligible to get a sync_state(). This is not sufficient for
devices that have no consumers but still need to do device state clean
up. So fix this.
Fixes: fc5a251d0f (driver core: Add sync_state driver/bus callback)
Signed-off-by: Saravana Kannan <saravanak@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200221080510.197337-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=iSMT
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 5.6-rc
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
phy: brcm-sata: Correct MDIO operations for 40nm platforms
phy: ti: gmii-sel: do not fail in case of gmii
phy: ti: gmii-sel: fix set of copy-paste errors
phy: core: Fix phy_get() to not return error on link creation failure
phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval
As we have pinned the timeline (using tl->active_count), we can safely
drop the tl->mutex as we wait for what we believe to be the final
request on that timeline. This is useful for ensuring that we do not
block the engine heartbeat by hogging the kernel_context's timeline on a
dead GPU.
References: https://gitlab.freedesktop.org/drm/intel/issues/1364
Fixes: 058179e72e ("drm/i915/gt: Replace hangcheck by heartbeats")
Fixes: f33a8a5160 ("drm/i915: Merge wait_for_timelines with retire_request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303140009.1494819-1-chris@chris-wilson.co.uk
(cherry picked from commit 82126e596d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We still need to wait for the initial OA configuration to happen
before we enable OA report writes to the OA buffer.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 15d0ace1f8 ("drm/i915/perf: execute OA configuration from command stream")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1356
Testcase: igt/perf/stream-open-close
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302085812.4172450-7-chris@chris-wilson.co.uk
(cherry picked from commit 4b4e973d5e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In the initial MIO support introduced in
commit 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
zpci_map_resource() and zpci_setup_resources() default to using the
mio_wb address as the resource's start address. This means users of the
mapping, which includes most drivers, will get write combining on PCI
Stores. This may lead to problems when drivers expect write through
behavior when not using an explicit ioremap_wc().
Cc: stable@vger.kernel.org
Fixes: 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On s390 there currently is no implementation of pud_write(). That was ok
as long as we had our own implementation of get_user_pages_fast() which
checked for pud protection by testing the bit directly w/o using
pud_write(). The other callers of pud_write() are not reachable on s390.
After commit 1a42010cdc ("s390/mm: convert to the generic
get_user_pages_fast code") we use the generic get_user_pages_fast(), which
does call pud_write() in pud_access_permitted() for FOLL_WRITE access on
a large pud. Without an s390 specific pud_write(), the generic version is
called, which contains a BUG() statement to remind us that we don't have a
proper implementation. This results in a kernel panic.
Fix this by providing an implementation of pud_write().
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 1a42010cdc ("s390/mm: convert to the generic get_user_pages_fast code")
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Commit 0e4a459f56 ("tracing: Remove unnecessary DEBUG_FS dependency")
removed select for DEBUG_FS but we still need it for development purposes.
Fixes: 0e4a459f56 ("tracing: Remove unnecessary DEBUG_FS dependency")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.
At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.
Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:
On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.
Factor out the usb_port_runtime_{resume,suspend}() changes into a
standalone patch to allow conflict-free porting on top of stable v3.9+.
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org
Fixes: 971fcd492c ("usb: add runtime pm support for usb port device")
Cc: stable@vger.kernel.org # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:
On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.
Factor out the usb_remove_device() change into a standalone patch to
allow conflict-free integration on top of the earliest stable branches.
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org
Fixes: 253e05724f ("USB: add a "remove hardware" sysfs attribute")
Cc: stable@vger.kernel.org # v2.6.33+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):
*** CID 1458999: Error handling issues (CHECKED_RETURN)
/drivers/usb/core/hub.c: 1869 in hub_probe()
1863
1864 if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND)
1865 hub->quirk_check_port_auto_suspend = 1;
1866
1867 if (id->driver_info & HUB_QUIRK_DISABLE_AUTOSUSPEND) {
1868 hub->quirk_disable_autosuspend = 1;
>>> CID 1458999: Error handling issues (CHECKED_RETURN)
>>> Calling "usb_autopm_get_interface" without checking return value (as is done elsewhere 97 out of 111 times).
1869 usb_autopm_get_interface(intf);
1870 }
1871
1872 if (hub_configure(hub, &desc->endpoint[0].desc) >= 0)
1873 return 0;
1874
Rather than checking the return value of 'usb_autopm_get_interface()',
switch to the usb_autopm_get_interface_no_resume() API, as per:
On Tue, Feb 25, 2020 at 10:32:32AM -0500, Alan Stern wrote:
------ 8< ------
> This change (i.e. 'ret = usb_autopm_get_interface') is not necessary,
> because the resume operation cannot fail at this point (interfaces
> are always powered-up during probe). A better solution would be to
> call usb_autopm_get_interface_no_resume() instead.
------ 8< ------
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: stable@vger.kernel.org # v4.14+
Reported-by: scan-admin@coverity.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-1-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current driver has 240 (USB2.0) and 2048 (USB3.0) as max_sectors,
e.g., /sys/bus/scsi/devices/0:0:0:0/max_sectors
If data access times out, driver error handling will issue a port
reset.
Sometimes Samsung Fit (090C:1000) flash disk will not respond to
later Set Address or Get Descriptor command.
Adding this quirk to limit max_sectors to 64 sectors to avoid issue
occurring.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1583158895-31342-1-git-send-email-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPM on the device appears to cause xHCI host controllers to claim
that there isn't enough bandwidth to support additional devices.
Signed-off-by: Dan Lazewatsky <dlaz@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4d7201cda2 ("usb: usb251xb: add vdd supply support") didn't
covered the non-DT use-case and so the regualtor_enable() call during
probe will fail on those platforms. Also the commit didn't handled the
error case correctly.
Move devm_regulator_get() out of usb251xb_get_ofdata() to address the
1st issue. This can be done without worries because devm_regulator_get()
handles the non-DT use-case too. Add devm_add_action_or_reset() to
address the 2nd bug.
Fixes: 4d7201cda2 ("usb: usb251xb: add vdd supply support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20200226072644.18490-1-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there are TRBs pending during reset endpoint operation, the
DMA will advance after reset operation, but it isn't expected,
since the data is not yet available (For OUT, the data is not
yet available). After the data is ready, there won't be any
interrupt since the EP_TRADDR already points to next TRB entry
and doorbell is not set.
To fix it, it toggles cycle bit before reset operation, and restores
it after reset, it could avoid unexpected DMA advance due to
cycle bit is for software during the endpoint reset operation.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has marked the dequeue trb as link trb, but its next segment
pointer is still itself, it causes the transfer can't go on. Fix
it by set its pointer as the trb address for the next request.
Fixes: f616c3bda4 ("usb: cdns3: Fix dequeue implementation")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When registers a phy_device successful, should terminate the loop
or the phy_device would be registered in other addr. If there are
multiple PHYs without reg properties, it will go wrong.
Signed-off-by: Dajun Jin <adajunjin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware can support more than 8 queues currently limited by
netif_get_num_default_rss_queues(). So, rework and fix checks for max
number of queues to allocate. The checks should be based on how many are
actually supported by hardware, OR the number of online cpus; whichever
is lower.
Fixes: 5952dde723 ("cxgb4: set maximal number of default RSS queues")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
This should improve the error message when the PHY validate in the MAC
driver failed. I ran into this problem multiple times that I put wrong
interface values into the device tree and was searching why it is
failing with -22 (-EINVAL). This should make it easier to spot the
problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink trigger command does not exist. While rewriting the
documentation for devlink into the reStructuredText format,
documentation for the trigger command was accidentally merged in. This
occurred because the author was also working on a potential extension to
devlink regions which included this trigger command, and accidentally
squashed the documentation incorrectly.
Further review eventually settled on using the previously unused "new"
command instead of creating a new trigger command.
Fix this by removing mention of the trigger command from the
documentation.
Fixes: 0b0f945f54 ("devlink: add a file documenting devlink regions", 2020-01-10)
Noticed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for tunnel source and
destination ports to the netlink policy.
Fixes: af308b94a2 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add missing attribute validation for NFTA_PAYLOAD_CSUM_FLAGS
to the netlink policy.
Fixes: 1814096980 ("netfilter: nft_payload: layer 4 checksum adjustment for pseudoheader fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If hook registration fails, the hooks allocated via nft_netdev_hook_alloc
need to be freed.
We can't change the goto label to 'goto 5' -- while it does fix the memleak
it does cause a warning splat from the netfilter core (the hooks were not
registered).
Fixes: 3f0465a9ef ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables")
Reported-by: syzbot+a2ff6fa45162a5ed4dd3@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Without patch:
# dd if=/proc/net/ip_tables_matches # original file output
conntrack
conntrack
conntrack
recent
recent
icmp
udplite
udp
tcp
0+1 records in
0+1 records out
65 bytes copied, 5.4074e-05 s, 1.2 MB/s
# dd if=/proc/net/ip_tables_matches bs=62 skip=1
dd: /proc/net/ip_tables_matches: cannot skip to specified offset
cp <<< end of last line
tcp <<< and then unexpected whole last line once again
0+1 records in
0+1 records out
7 bytes copied, 0.000102447 s, 68.3 kB/s
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Without the patch:
# dd if=/proc/net/xt_recent/SSH # original file outpt
src=127.0.0.4 ttl: 0 last_seen: 6275444819 oldest_pkt: 1 6275444819
src=127.0.0.2 ttl: 0 last_seen: 6275438906 oldest_pkt: 1 6275438906
src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
0+1 records in
0+1 records out
204 bytes copied, 6.1332e-05 s, 3.3 MB/s
Read after lseek into middle of last line (offset 140 in example below)
generates expected end of last line and then unexpected whole last line
once again
# dd if=/proc/net/xt_recent/SSH bs=140 skip=1
dd: /proc/net/xt_recent/SSH: cannot skip to specified offset
127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
0+1 records in
0+1 records out
132 bytes copied, 6.2487e-05 s, 2.1 MB/s
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
-----BEGIN PGP SIGNATURE-----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=VAHM
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: agilex: fix gmac compatible
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
* tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: (578 commits)
arm64: dts: socfpga: agilex: Fix gmac compatible
Linux 5.6-rc4
KVM: VMX: check descriptor table exits on instruction emulation
ext4: potential crash on allocation error in ext4_alloc_flex_bg_array()
macintosh: therm_windtunnel: fix regression when instantiating devices
jbd2: fix data races at struct journal_head
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
MAINTAINERS: Correct Cadence PCI driver path
io_uring: fix 32-bit compatability with sendmsg/recvmsg
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
...
Link: https://lore.kernel.org/r/20200303153509.28248-1-dinguyen@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Place phylink_start()/phylink_stop() inside dsa_port_enable() and
dsa_port_disable(), which ensures that we call phylink_stop() before
tearing down phylink - which is a documented requirement. Failure
to do so can cause use-after-free bugs.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=zLW4
-----END PGP SIGNATURE-----
Merge tag '5.6-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five small cifs/smb3 fixes, two for stable (one for a reconnect
problem and the other fixes a use case when renaming an open file)"
* tag '5.6-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Use #define in cifs_dbg
cifs: fix rename() by ensuring source handle opened with DELETE bit
cifs: add missing mount option to /proc/mounts
cifs: fix potential mismatch of UNC paths
cifs: don't leak -EAGAIN for stat() during reconnect
Hangbin Liu says:
====================
Fix IPv6 peer route update
Currently we have two issues for peer route update on IPv6.
1. When update peer route metric, we only updated the local one.
2. If peer address changed, we didn't remove the old one and add new one.
The first two patches fixed these issues and the third patch add new
tests to cover it.
With the fixes and updated test:
]# ./fib_tests.sh
IPv6 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
TEST: Set metric with peer route on local side [ OK ]
TEST: User specified metric on local address [ OK ]
TEST: Set metric with peer route on peer side [ OK ]
TEST: Modify metric with peer route on local side [ OK ]
TEST: Modify metric with peer route on peer side [ OK ]
IPv4 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
TEST: Modify metric of .0/24 address [ OK ]
TEST: Set metric of address with peer route [ OK ]
TEST: Modify metric of address with peer route [ OK ]
Tests passed: 22
Tests failed: 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update {ipv4, ipv6}_addr_metric_test with
1. Set metric of address with peer route and see if the route added
correctly.
2. Modify metric and peer address for peer route and see if the route
changed correctly.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we modify the peer route and changed it to a new one, we should
remove the old route first. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::3 proto kernel metric 256 pref medium
This patch depend on the previous patch "net/ipv6: need update peer route
when modify metric" to update new peer route after delete old one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we modify the route metric, the peer address's route need also
be updated. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 60 pref medium
2001:db8::2 proto kernel metric 60 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 60 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 61 pref medium
Fixes: 8308f3ff17 ("net/ipv6: Add support for specifying metric of connected routes")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DE3 VI layers support alpha blending, but DE2 VI layers do not.
Additionally, DE3 VI layers support 10-bit RGB and YUV formats.
Make a separate list for DE3.
Fixes: c50519e6db ("drm/sun4i: Add basic support for DE3")
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224173901.174016-3-jernej.skrabec@siol.net
Aaro Koskinen
Fabrice Gasnier
John Stultz
Olivier Moysan
Saravana Kannan
Greg Kroah-Hartman
Chris Wilson
Niklas Schnelle
Gerald Schaefer
Dinh Nguyen
Pratham Pratap
Eugeniu Rosca
Jim Lin
Dan Lazewatsky
Marco Felsch
Rikard Falkeborn
Peter Chen
Dajun Jin
Vishal Kulkarni
Hauke Mehrtens
Jonas Gorski
Jacob Keller
Jakub Kicinski
Florian Westphal
Vasily Averin
Olof Johansson
Jonathan Neuschäfer
Russell King
Linus Torvalds
David S. Miller
Hangbin Liu
Jernej Skrabec