When sending HCI data over NCI, HCI return code is part
of the NCI data. In order to get correctly the HCI return
code, we assume the NCI communication is successful and
extract the return code for the nci_hci functions return code.
This is done because nci_to_errno does not match hci return
code value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When sending HCI data over NCI, cmd information should be
present only on the first packet.
Each packet shall be specifically allocated and sent to the
NCI layer.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This functin takes as a parameter a pointer to the nci_dev
struct and the first byte from the values of the first domain
specific parameter that was used for the connection creation.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the number of destination speific parameters supplied is 0
the call will fail. If the first destination specific parameter
does not have a value, curr_id will be set to 0.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Initially it was used to create hooks in the driver for
proprietary operations. Currently it is being used for hooks
for both proprietary and generic operations.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver may be required to act when some responses or
notifications arrive. For example the NCI core does not have a
handler for NCI_OP_CORE_GET_CONFIG_RSP. The NFCC can send a
config response that has to be read by the driver and the packet
may contain vendor specific data.
The Fields Peak driver needs to take certain actions when a reset
notification arrives (packet also not handled by the nfc core).
The driver handlers do not interfere with the core and they are
called after the core processes the packet.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This allows sending core commands from the driver. The driver
should be able to send NCI core commands like CORE_GET_CONFIG_CMD.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver should know that it can continue with post setup where
setup left off. Being able to execute post_setup when setup fails
may force the developer to keep this state in the driver.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
FDP driver needs to send the firmware as regular packets
(not fragmented). The driver should have a way to
get the max packet size for a given connection.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For the firmware update the driver may use nci_send_data.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
poll(POLLOUT) on a listener should not report fd is ready for
a write().
This would break some applications using poll() and pfd.events = -1,
as they would not block in poll()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alan Burlison <Alan.Burlison@oracle.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TO: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
CC: linux-kernel@vger.kernel.org
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous changes in this series, we can now remove some
unused code and structures, both in the broadcast, link aggregation
and link code.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct synchronization of the broadcast link at first contact between
two nodes is dependent on the assumption that the binding table "bulk"
update passes via the same link as the initial broadcast syncronization
message, i.e., via the first link that is established.
This is not guaranteed in the current implementation. If two link
come up very close to each other in time, the "bulk" may quite well
pass via the second link, and hence void the guarantee of a correct
initial synchronization before the broadcast link is opened.
This commit makes two small changes to strengthen this guarantee.
1) We let the second established link occupy slot 1 of the
"active_links" array, while the first link will retain slot 0.
(This is in reality a cosmetic change, we could just as well keep
the current, opposite order)
2) We let the name distributor always use link selector/slot 0 when
it sends it binding table updates.
The extra traffic bias on the first link caused by this change should
be negligible, since binding table updates constitutes a very small
fraction of the total traffic.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent commit series, we have established a one-way dependency
between the link aggregation (struct tipc_node) instances and their
pertaining tipc_link instances. This has enabled quite significant code
and structure simplifications.
In this commit, we eliminate the field 'owner', which points to an
instance of struct tipc_node, from struct tipc_link, and replace it with
a pointer to struct net, which is the only external reference now needed
by a link instance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all packet transmitters (link, bcast, discovery) are now sending
consumable buffer clones to the bearer layer, we can remove the
redundant buffer cloning that is perfomed in the lower level functions
tipc_l2_send_msg() and tipc_udp_send_msg().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The neighbor discovery function currently uses the function
tipc_bearer_send() for transmitting packets, assuming that the
sent buffers are not consumed by the called function.
We want to change this, in order to avoid unnecessary buffer cloning
elswhere in the code.
This commit introduces a new function tipc_bearer_skb() which consumes
the sent buffers, and let the discoverer functions use this new call
instead. The discoverer does now itself perform the cloning when
that is necessary.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have only been supporting a fix MTU size of 1500 bytes
for all broadcast media, irrespective of their actual capability.
We now make the broadcast MTU adaptable to the carrying media, i.e.,
we use the smallest MTU supported by any of the interfaces attached
to TIPC.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have been keeping track of the exact set of broadcast
destinations though the help structure tipc_node_map. This leads us to
have to maintain a whole infrastructure for supporting this, including
a pseudo-bearer and a number of functions to manipulate both the bearers
and the node map correctly. Apart from the complexity, this approach is
also limiting, as struct tipc_node_map only can support cluster local
broadcast if we want to avoid it becoming excessively large. We want to
eliminate this limitation, in order to enable introduction of scoped
multicast in the future.
A closer analysis reveals that it is unnecessary maintaining this "full
set" overview; it is sufficient to keep a counter per bearer, indicating
how many nodes can be reached via this bearer at the moment. The protocol
is now robust enough to handle transitional discrepancies between the
nominal number of reachable destinations, as expected by the broadcast
protocol itself, and the number which is actually reachable at the
moment. The initial broadcast synchronization, in conjunction with the
retransmission mechanism, ensures that all packets will eventually be
acknowledged by the correct set of destinations.
This commit introduces these changes.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code path for receiving broadcast packets is currently distinct
from the unicast path. This leads to unnecessary code and data
duplication, something that can be avoided with some effort.
We now introduce separate per-peer tipc_link instances for handling
broadcast packet reception. Each receive link keeps a pointer to the
common, single, broadcast link instance, and can hence handle release
and retransmission of send buffers as if they belonged to the own
instance.
Furthermore, we let each unicast link instance keep a reference to both
the pertaining broadcast receive link, and to the common send link.
This makes it possible for the unicast links to easily access data for
broadcast link synchronization, as well as for carrying acknowledges for
received broadcast packets.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have tried to support both the newer, dedicated broadcast
synchronization mechanism along with the older, less safe, RESET_MSG/
ACTIVATE_MSG based one. The latter method has turned out to be a hazard
in a highly dynamic cluster, so we find it safer to disable it completely
when we find that the former mechanism is supported by the peer node.
For this purpose, we now introduce a new capabability bit,
TIPC_BCAST_SYNCH, to inform any peer nodes that dedicated broadcast
syncronization is supported by the present node. The new bit is conveyed
between peers in the 'capabilities' field of neighbor discovery messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit simplifies the broadcast link transmission function, by
leveraging previous changes to the link transmission function and the
broadcast transmission link life cycle.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realizing that unicast is just a special case of broadcast, we also see
that we can go in the other direction, i.e., that modest changes to the
current unicast link can make it generic enough to support broadcast.
The following changes are introduced here:
- A new counter ("ackers") in struct tipc_link, to indicate how many
peers need to ack a packet before it can be released.
- A corresponding counter in the skb user area, to keep track of how
many peers a are left to ack before a buffer can be released.
- A new counter ("acked"), to keep persistent track of how far a peer
has acked at the moment, i.e., where in the transmission queue to
start updating buffers when the next ack arrives. This is to avoid
double acknowledgements from a peer, with inadvertent relase of
packets as a result.
- A more generic tipc_link_retrans() function, where retransmit starts
from a given sequence number, instead of the first packet in the
transmision queue. This is to minimize the number of retransmitted
packets on the broadcast media.
When the new functionality is taken into use in the next commits,
we expect it to have minimal effect on unicast mode performance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The broadcast link instance (struct tipc_link) used for sending is
currently aggregated into struct tipc_bclink. This means that we cannot
use the regular tipc_link_create() function for initiating the link, but
do instead have to initiate numerous fields directly from the
bcast_init() function.
We want to reduce dependencies between the broadcast functionality
and the inner workings of tipc_link. In this commit, we introduce
a new function tipc_bclink_create() to link.c, and allocate the
instance of the link separately using this function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In reality, the link implementation is already independent from
struct tipc_bearer, in that it doesn't store any reference to it.
However, we still pass on a pointer to a bearer instance in the
function tipc_link_create(), just to have it extract some
initialization information from it.
I later commits, we need to create instances of tipc_link without
having any associated struct tipc_bearer. To facilitate this, we
want to extract the initialization data already in the creator
function in node.c, before calling tipc_link_create(), and pass
this info on as individual parameters in the call.
This commit introduces this change.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The broadcast transmission link is currently instantiated when the
network subsystem is started, i.e., on order from user space via netlink.
This forces the broadcast transmission code to do unnecessary tests for
the existence of the transmission link, as well in single mode node as
in network mode.
In this commit, we do instead create the link during initialization of
the name space, and remove it when it is stopped. The fact that the
transmission link now has a guaranteed longer life cycle than any of its
potential clients paves the way for further code simplifcations
and optimizations.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The broadcast lock will need to be acquired outside bcast.c in a later
commit. For this reason, we move the lock to struct tipc_net. Consistent
with the changes in the previous commit, we also introducee two new
functions tipc_bcast_lock() and tipc_bcast_unlock(). The code that is
currently using tipc_bclink_lock()/unlock() will be phased out during
the coming commits in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a number of structure and function definitions related
to the broadcast functionality are unnecessarily exposed in the file
bcast.h. This obscures the fact that the external interface towards
the broadcast link in fact is very narrow, and causes unnecessary
recompilations of other files when anything changes in those
definitions.
In this commit, we move as many of those definitions as is currently
possible to the file bcast.c.
We also rename the structure 'tipc_bclink' to 'tipc_bc_base', both
since the name does not correctly describe the contents of this
struct, and will do so even less in the future, and because we want
to use the term 'link' more appropriately in the functionality
introduced later in this series.
Finally, we rename a couple of functions, such as tipc_bclink_xmit()
and others that will be kept in the future, to include the term 'bcast'
instead.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-10-22
Here's probably the last bluetooth-next pull request for 4.4. Among
several other changes it contains the rest of the fixes & cleanups from
the Bluetooth UnplugFest (that didn't need to be hurried to 4.3).
- Refactoring & cleanups to 6lowpan code
- New USB ids for two Atheros controllers and BCM43142A0 from Broadcom
- Fix (quirk) for broken Broadcom BCM2045 controllers
- Support for latest Apple controllers
- Improvements to the vendor diagnostic message support
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The caches used to store sunrpc authentication information can be
flushed by writing a timestamp to a file in /proc.
This timestamp has a one-second resolution and any entry in cache that
was last_refreshed *before* that time is treated as expired.
This is problematic as it is not possible to reliably flush the cache
without interrupting NFS service.
If the current time is written to the "flush" file, any entry that was
added since the current second started will still be treated as valid.
If one second beyond than the current time is written to the file
then no entries can be valid until the second ticks over. This will
mean that no NFS request will be handled for up to 1 second.
To resolve this issue we make two changes:
1/ treat an entry as expired if the timestamp when it was last_refreshed
is before *or the same as* the expiry time. This means that current
code which writes out the current time will now flush the cache
reliably.
2/ when a new entry in added to the cache - set the last_refresh timestamp
to 1 second *beyond* the current flush time, when that not in the
past.
This ensures that newly added entries will always be valid.
Now that we have a very reliable way to flush the cache, and also
since we are using "since-boot" timestamps which are monotonic,
change cache_purge() to set the smallest future flush_time which
will work, and leave it there: don't revert to '1'.
Also disable the setting of the 'flush_time' far into the future.
That has never been useful and is now awkward as it would cause
last_refresh times to be strange.
Finally: if a request is made to set the 'flush_time' to the current
second, assume the intent is to flush the cache and advance it, if
necessary, to 1 second beyond the current 'flush_time' so that all
active entries will be deemed to be expired.
As part of this we need to add a 'cache_detail' arg to cache_init()
and cache_fresh_locked() so they can find the current ->flush_time.
Signed-off-by: NeilBrown <neilb@suse.com>
Reported-by: Olaf Kirch <okir@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The gss_key_timeout() function causes a harmless warning in some
configurations, e.g. ARM imx_v6_v7_defconfig with gcc-5.2, if the
compiler cannot figure out the state of the 'expire' variable across
an rcu_read_unlock():
net/sunrpc/auth_gss/auth_gss.c: In function 'gss_key_timeout':
net/sunrpc/auth_gss/auth_gss.c:1422:211: warning: 'expire' may be used uninitialized in this function [-Wmaybe-uninitialized]
To avoid this warning without adding a bogus initialization, this
rewrites the function so the comparison is done inside of the
critical section. As a side-effect, it also becomes slightly
easier to understand because the implementation now more closely
resembles the comment above it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c5e6aecd03 ("sunrpc: fix RCU handling of gc_ctx field")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If we're sending more pages via kernel_sendpage(), then set
MSG_SENDPAGE_NOTLAST.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-23
This series contains updates to i40e, i40evf, if_link, ixgbe and ixgbevf.
Anjali adds a workaround to drop any flow control frames from being
transmitted from any VSI, so that a malicious VF cannot send flow control
or PFC packets out on the wire. Also fixed a bug in debugfs by grabbing
the filter list lock before adding or deleting a filter.
Akeem fixes an issue where we were unconditionally returning VEB bridge
mode before allowing LB in the add VSI routine, resolve by checking if
the bridge is actually in VEB mode first.
Mitch fixed an issue where the incorrect structure was being used for
VLAN filter list, which meant the VLAN filter list did not get
processed correctly and VLAN filters would not be re-enabled after any
kind of reset.
Helin fixed a problem of possibly getting inconsistent flow control
status after a PF reset. The issue was requested_mode was being set
with a default value during probe, but the hardware state could be a
different value from this mode.
Carolyn fixed a problem where the driver output of the OEM version
string varied from the other tools.
Jean Sacren fixes up kernel documentation by fixing function header
comments to match actual variables used in the functions. Also
cleaned up variable initialization, when the variable would be
over-written immediately.
Hiroshi Shimanoto provides three patches to add "trusted" VF by adding
netlink directives and an NDO entry. Then implement these new controls
in ixgbe and ixgbevf. This series has gone through several iterations
to address all the suggested community changes and concerns.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the selection of a multipath route to use a flow-based
hash. This more suitable for traffic sensitive to reordering within a
flow (e.g. TCP, L2VPN) and whilst still allowing a good distribution
of traffic given enough flows.
Selection of the path for a multipath route is done using a hash of:
1. Label stack up to MAX_MP_SELECT_LABELS labels or up to and
including entropy label, whichever is first.
2. 3-tuple of (L3 src, L3 dst, proto) from IPv4/IPv6 header in MPLS
payload, if present.
Naturally, a 5-tuple hash using L4 information in addition would be
possible and be better in some scenarios, but there is a tradeoff
between looking deeper into the packet to achieve good distribution,
and packet forwarding performance, and I have erred on the side of the
latter as the default.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for MPLS multipath routes.
Includes following changes to support multipath:
- splits struct mpls_route into 'struct mpls_route + struct mpls_nh'
- 'struct mpls_nh' represents a mpls nexthop label forwarding entry
- moves mpls route and nexthop structures into internal.h
- A mpls_route can point to multiple mpls_nh structs
- the nexthops are maintained as a array (similar to ipv4 fib)
- In the process of restructuring, this patch also consistently changes
all labels to u8
- Adds support to parse/fill RTA_MULTIPATH netlink attribute for
multipath routes similar to ipv4/v6 fib
- In this patch, the multipath route nexthop selection algorithm
simply returns the first nexthop. It is replaced by a
hash based algorithm from Robert Shearman in the next patch
- mpls_route_update cleanup: remove 'dev' handling in mpls_route_update.
mpls_route_update though implemented to update based on dev, it was
never used that way. And the dev handling gets tricky with multiple
nexthops. Cannot match against any single nexthops dev. So, this patch
removes the unused 'dev' handling in mpls_route_update.
- dead route/path handling will be implemented in a subsequent patch
Example:
$ip -f mpls route add 100 nexthop as 200 via inet 10.1.1.2 dev swp1 \
nexthop as 700 via inet 10.1.1.6 dev swp2 \
nexthop as 800 via inet 40.1.1.2 dev swp3
$ip -f mpls route show
100
nexthop as to 200 via inet 10.1.1.2 dev swp1
nexthop as to 700 via inet 10.1.1.6 dev swp2
nexthop as to 800 via inet 40.1.1.2 dev swp3
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink directives and ndo entry to trust VF user.
This controls the special permission of VF user.
The administrator will dedicatedly trust VF user to use some features
which impacts security and/or performance.
The administrator never turn it on unless VF user is fully trusted.
CC: Sy Jong Choi <sy.jong.choi@intel.com>
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Multiple cpus can process duplicates of incoming ACK messages
matching a SYN_RECV request socket. This is a rare event under
normal operations, but definitely can happen.
Only one must win the race, otherwise corruption would occur.
To fix this without adding new atomic ops, we use logic in
inet_ehash_nolisten() to detect the request was present in the same
ehash bucket where we try to insert the new child.
If request socket was not found, we have to undo the child creation.
This actually removes a spin_lock()/spin_unlock() pair in
reqsk_queue_unlink() for the fast path.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently adding a new ipv4 address always cause the creation of the
related network route, with default metric. When a host has multiple
interfaces on the same network, multiple routes with the same metric
are created.
If the userspace wants to set specific metric on each routes, i.e.
giving better metric to ethernet links in respect to Wi-Fi ones,
the network routes must be deleted and recreated, which is error-prone.
This patch implements the support for IFA_F_NOPREFIXROUTE for ipv4
address. When an address is added with such flag set, no associated
network route is created, no network route is deleted when
said IP is gone and it's up to the user space manage such route.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raw sockets with hdrincl enabled can insert ipv6 extension headers
right into the data stream. In case we need to fragment those packets,
we reparse the options header to find the place where we can insert
the fragment header. If the extension headers exceed the link's MTU we
actually cannot make progress in such a case.
Instead of ending up in broken arithmetic or rounding towards 0 and
entering an endless loop in ip6_fragment, just prevent those cases by
aborting early and signal -EMSGSIZE to user space.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If alpha is strictly reduced by alpha >> dctcp_shift_g and if alpha is less
than 1 << dctcp_shift_g, then alpha may never reach zero. For example,
given shift_g=4 and alpha=15, alpha >> dctcp_shift_g yields 0 and alpha
remains 15. The effect isn't noticeable in this case below cwnd=137, but
could gradually drive uncongested flows with leftover alpha down to
cwnd=137. A larger dctcp_shift_g would have a greater effect.
This change causes alpha=15 to drop to 0 instead of being decrementing by 1
as it would when alpha=16. However, it requires one less conditional to
implement since it doesn't have to guard against subtracting 1 from 0U. A
decay of 15 is not unreasonable since an equal or greater amount occurs at
alpha >= 240.
Signed-off-by: Andrew G. Shewmaker <agshew@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error condition -EAGAIN, which is signaled by throw routes, tells
the rules framework to walk on searching for next matches. If the walk
ends and we stop walking the rules with the result of a throw route we
have to translate the error conditions to -ENETUNREACH.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increment the LINUX_MIB_XFRMINSTATEMODEERROR statistic counter
to notify about dropped packets if we fail to fetch a inner mode.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
A call to pskb_may_pull may change the pointers into the packet,
so reload the pointers after the call.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We skip the header informations if the data pointer points
already behind the header in question for some protocols.
This is because we call pskb_may_pull with a negative value
converted to unsigened int from pskb_may_pull in this case.
Skipping the header informations can lead to incorrect policy
lookups, so fix it by a check of the data pointer position
before we call pskb_may_pull.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
On sparc, deleting established SAs (e.g., by restarting ipsec)
results in unaligned access messages via xfrm_del_sa ->
km_state_notify -> xfrm_send_state_notify().
Even though struct xfrm_usersa_info is aligned on 8-byte boundaries,
netlink attributes are fundamentally only 4 byte aligned, and this
cannot be changed for nla_data() that is passed up to userspace.
As a result, the put_unaligned() macro needs to be used to
set up potentially unaligned fields such as the xfrm_stats in
copy_to_user_state()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent fix for the vsock sock_put issue used the wrong
initializer for the transport spin_lock causing an issue when
running with lockdep checking.
Testing: Verified fix on kernel with lockdep enabled.
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2015-10-22
1) Fix IPsec pre-encap fragmentation for GSO packets.
From Herbert Xu.
2) Fix some header checks in _decode_session6.
We skip the header informations if the data pointer points
already behind the header in question for some protocols.
This is because we call pskb_may_pull with a negative value
converted to unsigened int from pskb_may_pull in this case.
Skipping the header informations can lead to incorrect policy
lookups. From Mathias Krause.
3) Allow to change the replay threshold and expiry timer of a
state without having to set other attributes like replay
counter and byte lifetime. Changing these other attributes
may break the SA. From Michael Rossberg.
4) Fix pmtu discovery for local generated packets.
We may fail dispatch to the inner address family.
As a reault, the local error handler is not called
and the mtu value is not reported back to userspace.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No driver implements port_fdb_getnext anymore, and port_fdb_dump is
preferred anyway, so remove this function from DSA.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all switch chips support a Get Next operation to iterate on its FDB.
So add a more simple port_fdb_dump function for them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
741a11d9e4 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
adds the RT6_LOOKUP_F_IFACE flag to make device index mismatch fatal if
oif is given. Hajime reported that this change breaks the Mobile IPv6
use case that wants to force the message through one interface yet use
the source address from another interface. Handle this case by only
adding the flag if oif is set and saddr is not set.
Fixes: 741a11d9e4 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
Cc: Hajime Tazaki <thehajime@gmail.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=uZ5N
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another set of patches for the current cycle:
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vsock vmci_transport driver, sock_put wasn't safe to call
in interrupt context, since that may call the vsock destructor
which in turn calls several functions that should only be called
from process context. This change defers the callling of these
functions to a worker thread. All these functions were
deallocation of resources related to the transport itself.
Furthermore, an unused callback was removed to simplify the
cleanup.
Multiple customers have been hitting this issue when using
VMware tools on vSphere 2015.
Also added a version to the vmci transport module (starting from
1.0.2.0-k since up until now it appears that this module was
sharing version with vsock that is currently at 1.0.1.0-k).
Reviewed-by: Aditya Asarwade <asarwade@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, NETLINK_LIST_MEMBERSHIPS grabs the netlink table while copying
the membership state to user-space. However, grabing the netlink table is
effectively a write_lock_irq(), and as such we should not be triggering
page-faults in the critical section.
This can be easily reproduced by the following snippet:
int s = socket(AF_NETLINK, SOCK_RAW, NETLINK_ROUTE);
void *p = mmap(0, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANON, -1, 0);
int r = getsockopt(s, 0x10e, 9, p, (void*)((char*)p + 4092));
This should work just fine, but currently triggers EFAULT and a possible
WARN_ON below handle_mm_fault().
Fix this by reducing locking of NETLINK_LIST_MEMBERSHIPS to a read-side
lock. The write-lock was overkill in the first place, and the read-lock
allows page-faults just fine.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With use of lwtunnel, we can directly call dev_queue_xmit()
rather than calling netdev vport send operation.
Following change make tunnel vport code bit cleaner.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch fixes following sparse warning.
net/openvswitch/flow_netlink.c:583:30: warning: incorrect type in assignment (different base types)
net/openvswitch/flow_netlink.c:583:30: expected restricted __be16 [usertype] ipv4
net/openvswitch/flow_netlink.c:583:30: got int
Fixes: 6b26ba3a7d ("openvswitch: netlink attributes for IPv6 tunneling")
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iptables -I INPUT ... -j TEE --gateway 10.1.2.3
<crash> because --oif was not specified
tee_tg_check() sets ->priv pointer to NULL in this case.
Fixes: bbde9fc182 ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With the addition of support for diagnostic feature, it makes sense to
increase the minor version of the Bluetooth core module.
The module version is not used anywhere, but it gives a nice extra
hint for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Looking at current situation of memory management in 6lowpan receive
function I detected some invalid handling. After calling
lowpan_invoke_rx_handlers we will do a kfree_skb and then NET_RX_DROP on
error handling. We don't do this before, also on
skb_share_check/skb_unshare which might manipulate the reference
counters.
After running some 'grep -r "dev_add_pack" net/' to look how others
packet-layer receive callbacks works I detected that every subsystem do
a kfree_skb, then NET_RX_DROP without calling skb functions which
might manipulate the skb reference counters. This is the reason why we
should do the same here like all others subsystems. I didn't find any
documentation how the packet-layer receive callbacks handle NET_RX_DROP
return values either.
This patch will add a kfree_skb, then NET_RX_DROP handling for the
"trivial checks", in case of skb_share_check/skb_unshare the kfree_skb
call will be done inside these functions.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are a few places that don't explicitly check the connection
state before calling hci_disconnect(). To make this API do the right
thing take advantage of the new hci_abort_conn() API and also make
sure to only read the clock offset if we're really connected.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Convert the various places mapping connection state to
disconnect/cancel HCI command to use the new hci_abort_conn helper
API.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are several different places needing to make sure that a
connection gets disconnected or canceled. The exact action needed
depends on the connection state, so centralizing this logic can save
quite a lot of code duplication.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For connection parameters that are left around until a disconnection
we should at least clear any auto-connection properties. This way a
new Add Device call is required to re-set them after calling Unpair
Device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tom Herbert added SIT support to GRO with commit
19424e052f ("sit: Add gro callbacks to sit_offload"),
later reverted by Herbert Xu.
The problem came because Tom patch was building GRO
packets without proper meta data : If packets were locally
delivered, we would not care.
But if packets needed to be forwarded, GSO engine was not
able to segment individual segments.
With the following patch, we correctly set skb->encapsulation
and inner network header. We also update gso_type.
Tested:
Server :
netserver
modprobe dummy
ifconfig dummy0 8.0.0.1 netmask 255.255.255.0 up
arp -s 8.0.0.100 4e:32:51:04:47:e5
iptables -I INPUT -s 10.246.7.151 -j TEE --gateway 8.0.0.100
ifconfig sixtofour0
sixtofour0 Link encap:IPv6-in-IPv4
inet6 addr: 2002:af6:798::1/128 Scope:Global
inet6 addr: 2002:af6:798::/128 Scope:Global
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:411169 errors:0 dropped:0 overruns:0 frame:0
TX packets:409414 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:20319631739 (20.3 GB) TX bytes:29529556 (29.5 MB)
Client :
netperf -H 2002:af6:798::1 -l 1000 &
Checked on server traffic copied on dummy0 and verify segments were
properly rebuilt, with proper IP headers, TCP checksums...
tcpdump on eth0 shows proper GRO aggregation takes place.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If userspace provides a ct action with no nested mark or label, then the
storage for these fields is zeroed. Later when actions are requested,
such zeroed fields are serialized even though userspace didn't
originally specify them. Fix the behaviour by ensuring that no action is
serialized in this case, and reject actions where userspace attempts to
set these fields with mask=0. This should make netlink marshalling
consistent across deserialization/reserialization.
Reported-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
New, related connections are marked as such as part of ovs_ct_lookup(),
but they are not marked as "new" if the commit flag is used. Make this
consistent by setting the "new" flag whenever !nf_ct_is_confirmed(ct).
Reported-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, 0-bits are generated in ct_state where the bit position is
undefined, and matches are accepted on these bit-positions. If userspace
requests to match the 0-value for this bit then it may expect only a
subset of traffic to match this value, whereas currently all packets
will have this bit set to 0. Fix this by rejecting such masks.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains four Netfilter fixes for net, they are:
1) Fix Kconfig dependencies of new nf_dup_ipv4 and nf_dup_ipv6.
2) Remove bogus test nh_scope in IPv4 rpfilter match that is breaking
--accept-local, from Xin Long.
3) Wait for RCU grace period after dropping the pending packets in the
nfqueue, from Florian Westphal.
4) Fix sleeping allocation while holding spin_lock_bh, from Nikolay Borisov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
if_nlmsg_size() overestimates the minimum allocation size of netlink
dump request (when called from rtnl_calcit()) or the size of the
message (when called from rtnl_getlink()). This is because
ext_filter_mask is not supported by rtnl_link_get_af_size() and
rtnl_link_get_size().
The over-estimation is significant when at least one netdev has many
VLANs configured (8 bytes for each configured VLAN).
This patch-set "rightsizes" the protocol specific attribute size
calculation by propagating ext_filter_mask to rtnl_link_get_af_size()
and adding this a argument to get_link_af_size op in rtnl_af_ops.
Bridge module already used filtering aware sizing for notifications.
br_get_link_af_size_filtered() is consistent with the modified
get_link_af_size op so it replaces br_get_link_af_size() in br_af_ops.
br_get_link_af_size() becomes unused and thus removed.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d999297c3d ("tipc: reduce locking scope during packet reception")
we altered the packet retransmission function. Since then, when
restransmitting packets, we create a clone of the original buffer
using __pskb_copy(skb, MIN_H_SIZE), where MIN_H_SIZE is the size of
the area we want to have copied, but also the smallest possible TIPC
packet size. The value of MIN_H_SIZE is 24.
Unfortunately, __pskb_copy() also has the effect that the headroom
of the cloned buffer takes the size MIN_H_SIZE. This is too small
for carrying the packet over the UDP tunnel bearer, which requires
a minimum headroom of 28 bytes. A change to just use pskb_copy()
lets the clone inherit the original headroom of 80 bytes, but also
assumes that the copied data area is of at least that size, something
that is not always the case. So that is not a viable solution.
We now fix this by adding a check for sufficient headroom in the
transmit function of udp_media.c, and expanding it when necessary.
Fixes: commit d999297c3d ("tipc: reduce locking scope during packet reception")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code for message reassembly is erroneously assuming that
the the first arriving fragment buffer always is linear, and then goes
ahead resetting the fragment list of that buffer in anticipation of
more arriving fragments.
However, if the buffer already happens to be non-linear, we will
inadvertently drop the already attached fragment list, and later
on trig a BUG() in __pskb_pull_tail().
We see this happen when running fragmented TIPC multicast across UDP,
something made possible since
commit d0f91938be ("tipc: add ip/udp media type")
We fix this by not resetting the fragment list when the buffer is non-
linear, and by initiatlizing our private fragment list tail pointer to
the tail of the existing fragment list.
Fixes: commit d0f91938be ("tipc: add ip/udp media type")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"openvswitch: Remove vport stats" removed the per-vport statistics, in
order to use the netdev's statistics fields.
"openvswitch: Fix ovs_vport_get_stats()" fixed the export of these stats
to user-space, by using the provided netdev_ops to collate them - but ovs
internal devices still use an unallocated dev->tstats field to count
packets, which are no longer exported by this api.
Allocate the dev->tstats field for ovs internal devices, and wire up
ndo_get_stats64 with the original implementation of
ovs_vport_get_stats().
On its own, "openvswitch: Fix ovs_vport_get_stats()" fixes the OOPs,
unmasking a full-on panic on arm64:
=============%<==============
[<ffffffbffc00ce4c>] internal_dev_recv+0xa8/0x170 [openvswitch]
[<ffffffbffc0008b4>] do_output.isra.31+0x60/0x19c [openvswitch]
[<ffffffbffc000bf8>] do_execute_actions+0x208/0x11c0 [openvswitch]
[<ffffffbffc001c78>] ovs_execute_actions+0xc8/0x238 [openvswitch]
[<ffffffbffc003dfc>] ovs_packet_cmd_execute+0x21c/0x288 [openvswitch]
[<ffffffc0005e8c5c>] genl_family_rcv_msg+0x1b0/0x310
[<ffffffc0005e8e60>] genl_rcv_msg+0xa4/0xe4
[<ffffffc0005e7ddc>] netlink_rcv_skb+0xb0/0xdc
[<ffffffc0005e8a94>] genl_rcv+0x38/0x50
[<ffffffc0005e76c0>] netlink_unicast+0x164/0x210
[<ffffffc0005e7b70>] netlink_sendmsg+0x304/0x368
[<ffffffc0005a21c0>] sock_sendmsg+0x30/0x4c
[SNIP]
Kernel panic - not syncing: Fatal exception in interrupt
=============%<==============
Fixes: 8c876639c9 ("openvswitch: Remove vport stats.")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6e28b00082 ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.
Fixes: 42a7b32b73 ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default fix broadcast window size is currently set to 20 packets.
This is a very low value, set at a time when we were still testing on
10 Mb/s hubs, and a change to it is long overdue.
Commit 7845989cb4 ("net: tipc: fix stall during bclink wakeup procedure")
revealed a problem with this low value. For messages of importance LOW,
the backlog queue limit will be calculated to 30 packets, while a
single, maximum sized message of 66000 bytes, carried across a 1500 MTU
network consists of 46 packets.
This leads to the following scenario (among others leading to the same
situation):
1: Msg 1 of 46 packets is sent. 20 packets go to the transmit queue, 26
packets to the backlog queue.
2: Msg 2 of 46 packets is attempted sent, but rejected because there is
no more space in the backlog queue at this level. The sender is added
to the wakeup queue with a "pending packets chain size" number of 46.
3: Some packets in the transmit queue are acked and released. We try to
wake up the sender, but the pending size of 46 is bigger than the LOW
wakeup limit of 30, so this doesn't happen.
5: Subsequent acks releases all the remaining buffers. Each time we test
for the wakeup criteria and find that 46 still is larger than 30,
even after both the transmit and the backlog queues are empty.
6: The sender is never woken up and given a chance to send its message.
He is stuck.
We could now loosen the wakeup criteria (used by link_prepare_wakeup())
to become equal to the send criteria (used by tipc_link_xmit()), i.e.,
by ignoring the "pending packets chain size" value altogether, or we can
just increase the queue limits so that the criteria can be satisfied
anyway. There are good reasons (potentially multiple waiting senders) to
not opt for the former solution, so we choose the latter one.
This commit fixes the problem by giving the broadcast link window a
default value of 50 packets. We also introduce a new minimum link
window size BCLINK_MIN_WIN of 32, which is enough to always avoid the
described situation. Finally, in order to not break any existing users
which may set the window explicitly, we enforce that the window is set
to the new minimum value in case the user is trying to set it to
anything lower.
Fixes: 7845989cb4 ("net: tipc: fix stall during bclink wakeup procedure")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's only one user of this helper which can be replaces with a call
to hci_pend_le_action_lookup() and a check for params->explicit_connect.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no need to clear the HCI_CONN_ENCRYPT_PEND flag in
smp_failure. In fact, this may cause the encryption tracking to get
out of sync as this has nothing to do with HCI activity.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_le_create_connection_cancel() function needs to use the hdev
pointer in many places so add a variable for it to avoid the need to
dereference the hci_conn every time.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of doing all of the LE-specific handling in an else-branch in
unpair_device() create a 'done' label for the BR/EDR branch to jump to
and then remove the else-branch completely.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the new hci_conn_hash_lookup_le() API to look up LE connections.
This way we're guaranteed exact matches that also take into account
the address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the new hci_conn_hash_lookup_le() API to look up LE connections.
This way we're guaranteed exact matches that also take into account
the address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt code needs to convert from mgmt/L2CAP address types to HCI in
many places. Having a dedicated helper function for this simplifies
code by shortening it and removing unnecessary 'addr_type' variables.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Configure ageing time to the HW for newly bridged device
CC: Scott Feldman <sfeldma@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is decrementing the pointer, instead of the value stored in the
pointer. KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reset transport and unlock if misc_register failed.
Signed-off-by: Gao feng <omarapazanadi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the second half of RACK that uses the the most
recent transmit time among all delivered packets to detect losses.
tcp_rack_mark_lost() is called upon receiving a dubious ACK.
It then checks if an not-yet-sacked packet was sent at least
"reo_wnd" prior to the sent time of the most recently delivered.
If so the packet is deemed lost.
The "reo_wnd" reordering window starts with 1msec for fast loss
detection and changes to min-RTT/4 when reordering is observed.
We found 1msec accommodates well on tiny degree of reordering
(<3 pkts) on faster links. We use min-RTT instead of SRTT because
reordering is more of a path property but SRTT can be inflated by
self-inflicated congestion. The factor of 4 is borrowed from the
delayed early retransmit and seems to work reasonably well.
Since RACK is still experimental, it is now used as a supplemental
loss detection on top of existing algorithms. It is only effective
after the fast recovery starts or after the timeout occurs. The
fast recovery is still triggered by FACK and/or dupack threshold
instead of RACK.
We introduce a new sysctl net.ipv4.tcp_recovery for future
experiments of loss recoveries. For now RACK can be disabled by
setting it to 0.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the first half of the RACK loss recovery.
RACK loss recovery uses the notion of time instead
of packet sequence (FACK) or counts (dupthresh). It's inspired by the
previous FACK heuristic in tcp_mark_lost_retrans(): when a limited
transmit (new data packet) is sacked, then current retransmitted
sequence below the newly sacked sequence must been lost,
since at least one round trip time has elapsed.
But it has several limitations:
1) can't detect tail drops since it depends on limited transmit
2) is disabled upon reordering (assumes no reordering)
3) only enabled in fast recovery ut not timeout recovery
RACK (Recently ACK) addresses these limitations with the notion
of time instead: a packet P1 is lost if a later packet P2 is s/acked,
as at least one round trip has passed.
Since RACK cares about the time sequence instead of the data sequence
of packets, it can detect tail drops when later retransmission is
s/acked while FACK or dupthresh can't. For reordering RACK uses a
dynamically adjusted reordering window ("reo_wnd") to reduce false
positives on ever (small) degree of reordering.
This patch implements tcp_advanced_rack() which tracks the
most recent transmission time among the packets that have been
delivered (ACKed or SACKed) in tp->rack.mstamp. This timestamp
is the key to determine which packet has been lost.
Consider an example that the sender sends six packets:
T1: P1 (lost)
T2: P2
T3: P3
T4: P4
T100: sack of P2. rack.mstamp = T2
T101: retransmit P1
T102: sack of P2,P3,P4. rack.mstamp = T4
T205: ACK of P4 since the hole is repaired. rack.mstamp = T101
We need to be careful about spurious retransmission because it may
falsely advance tp->rack.mstamp by an RTT or an RTO, causing RACK
to falsely mark all packets lost, just like a spurious timeout.
We identify spurious retransmission by the ACK's TS echo value.
If TS option is not applicable but the retransmission is acknowledged
less than min-RTT ago, it is likely to be spurious. We refrain from
using the transmission time of these spurious retransmissions.
The second half is implemented in the next patch that marks packet
lost using RACK timestamp.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a helper to prepare the main RACK patch
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the existing lost retransmit detection because RACK subsumes
it completely. This also stops the overloading the ack_seq field of
the skb control block.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kathleen Nichols' algorithm for tracking the minimum RTT of a
data stream over some measurement window. It uses constant space
and constant time per update. Yet it almost always delivers
the same minimum as an implementation that has to keep all
the data in the window. The measurement window is tunable via
sysctl.net.ipv4.tcp_min_rtt_wlen with a default value of 5 minutes.
The algorithm keeps track of the best, 2nd best & 3rd best min
values, maintaining an invariant that the measurement time of
the n'th best >= n-1'th best. It also makes sure that the three
values are widely separated in the time window since that bounds
the worse case error when that data is monotonically increasing
over the window.
Upon getting a new min, we can forget everything earlier because
it has no value - the new min is less than everything else in the
window by definition and it's the most recent. So we restart fresh
on every new min and overwrites the 2nd & 3rd choices. The same
property holds for the 2nd & 3rd best.
Therefore we have to maintain two invariants to maximize the
information in the samples, one on values (1st.v <= 2nd.v <=
3rd.v) and the other on times (now-win <=1st.t <= 2nd.t <= 3rd.t <=
now). These invariants determine the structure of the code
The RTT input to the windowed filter is the minimum RTT measured
from ACK or SACK, or as the last resort from TCP timestamps.
The accessor tcp_min_rtt() returns the minimum RTT seen in the
window. ~0U indicates it is not available. The minimum is 1usec
even if the true RTT is below that.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ca_seq_rtt_us does not use Kern's check. Fix that by
checking if any packet acked is a retransmit, for both RTT used
for RTT estimation and congestion control.
Fixes: 5b08e47ca ("tcp: prefer packet timing to TS-ECR for RTT")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hci_conn objects don't have a dedicated lock themselves but rely
on the caller to hold the hci_dev lock for most types of access. The
hci_conn_timeout() function has so far sent certain HCI commands based
on the hci_conn state which has been possible without holding the
hci_dev lock.
The recent changes to do LE scanning before connect attempts added
even more operations to hci_conn and hci_dev from hci_conn_timeout,
thereby exposing potential race conditions with the hci_dev and
hci_conn states.
As an example of such a race, here there's a timeout but an
l2cap_sock_connect() call manages to race with the cleanup routine:
[Oct21 08:14] l2cap_chan_timeout: chan ee4b12c0 state BT_CONNECT
[ +0.000004] l2cap_chan_close: chan ee4b12c0 state BT_CONNECT
[ +0.000002] l2cap_chan_del: chan ee4b12c0, conn f3141580, err 111, state BT_CONNECT
[ +0.000002] l2cap_sock_teardown_cb: chan ee4b12c0 state BT_CONNECT
[ +0.000005] l2cap_chan_put: chan ee4b12c0 orig refcnt 4
[ +0.000010] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[ +0.000013] l2cap_chan_put: chan ee4b12c0 orig refcnt 3
[ +0.000063] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[ +0.000049] hci_conn_params_del: addr ee:0d:30:09:53:1f (type 1)
[ +0.000002] hci_chan_list_flush: hcon f53d56e0
[ +0.000001] hci_chan_del: hci0 hcon f53d56e0 chan f4e7ccc0
[ +0.004528] l2cap_sock_create: sock e708fc00
[ +0.000023] l2cap_chan_create: chan ee4b1770
[ +0.000001] l2cap_chan_hold: chan ee4b1770 orig refcnt 1
[ +0.000002] l2cap_sock_init: sk ee4b3390
[ +0.000029] l2cap_sock_bind: sk ee4b3390
[ +0.000010] l2cap_sock_setsockopt: sk ee4b3390
[ +0.000037] l2cap_sock_connect: sk ee4b3390
[ +0.000002] l2cap_chan_connect: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f (type 2) psm 0x00
[ +0.000002] hci_get_route: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f
[ +0.000001] hci_dev_hold: hci0 orig refcnt 8
[ +0.000003] hci_conn_hold: hcon f53d56e0 orig refcnt 0
Above the l2cap_chan_connect() shouldn't have been able to reach the
hci_conn f53d56e0 anymore but since hci_conn_timeout didn't do proper
locking that's not the case. The end result is a reference to hci_conn
that's not in the conn_hash list, resulting in list corruption when
trying to remove it later:
[Oct21 08:15] l2cap_chan_timeout: chan ee4b1770 state BT_CONNECT
[ +0.000004] l2cap_chan_close: chan ee4b1770 state BT_CONNECT
[ +0.000003] l2cap_chan_del: chan ee4b1770, conn f3141580, err 111, state BT_CONNECT
[ +0.000001] l2cap_sock_teardown_cb: chan ee4b1770 state BT_CONNECT
[ +0.000005] l2cap_chan_put: chan ee4b1770 orig refcnt 4
[ +0.000002] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[ +0.000015] l2cap_chan_put: chan ee4b1770 orig refcnt 3
[ +0.000038] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[ +0.000003] hci_chan_list_flush: hcon f53d56e0
[ +0.000002] hci_conn_hash_del: hci0 hcon f53d56e0
[ +0.000001] ------------[ cut here ]------------
[ +0.000461] WARNING: CPU: 0 PID: 1782 at lib/list_debug.c:56 __list_del_entry+0x3f/0x71()
[ +0.000839] list_del corruption, f53d56e0->prev is LIST_POISON2 (00000200)
The necessary fix is unfortunately more complicated than just adding
hci_dev_lock/unlock calls to the hci_conn_timeout() call path.
Particularly, the hci_conn_del() API, which expects the hci_dev lock to
be held, performs a cancel_delayed_work_sync(&hcon->disc_work) which
would lead to a deadlock if the hci_conn_timeout() call path tries to
acquire the same lock.
This patch solves the problem by deferring the cleanup work to a
separate work callback. To protect against the hci_dev or hci_conn
going away meanwhile temporary references are taken with the help of
hci_dev_hold() and hci_conn_get().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.3
Group station statistics by where they're (mostly) updated
(TX, RX and TX-status) and group them into sub-structs of
the struct sta_info.
Also rename the variables since the grouping now makes it
obvious where they belong.
This makes it easier to identify where the statistics are
updated in the code, and thus easier to think about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This file only feeds a debugfs file that isn't very useful, so remove
it. If necessary, we can add other ways to get this information, for
example in the NL80211_CMD_PROBE_CLIENT response.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers might have to restore certain settings after the init
procedure has been completed. This driver callback allows them to hook
into that stage. This callback is run just before the controller is
declared as powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is a L2CAP protocol race between the local peer and
the remote peer demanding disconnection of the L2CAP link.
When L2CAP ERTM is used, l2cap_sock_shutdown() can be called
from userland to disconnect L2CAP. However, there can be a
delay introduced by waiting for ACKs. During this waiting
period, the remote peer may have sent a Disconnection Request.
Therefore, recheck the shutdown status of the socket
after waiting for ACKs because there is no need to do
further processing if the connection has gone.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This commit reorganizes the mutex lock and is now
only protecting l2cap_chan_close(). This is now consistent
with other places where l2cap_chan_close() is called.
If a conn connection exists, call
mutex_lock(&conn->chan_lock) before calling l2cap_chan_close()
to ensure other L2CAP protocol operations do not interfere.
Note that the conn structure has to be protected from being
freed as it is possible for the connection to be disconnected
whilst the locks are not held. This solution allows the mutex
lock to be used even when the connection has just been
disconnected.
This commit also reduces the scope of chan locking.
The only place where chan locking is needed is the call to
l2cap_chan_close(chan, 0) which if necessary closes the channel.
Therefore, move the l2cap_chan_lock(chan) and
l2cap_chan_lock(chan) locking calls to around
l2cap_chan_close(chan, 0).
This allows __l2cap_wait_ack(sk, chan) to be called with no
chan locks being held so L2CAP messaging over the ACL link
can be done unimpaired.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
l2cap_sock_shutdown() is designed to only action shutdown
of the channel when shutdown is not already in progress.
Therefore, reorganise the code flow by adding a goto
to jump to the end of function handling when shutdown is
already being actioned. This removes one level of code
indentation and make the code more readable.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the mcast compression algorithmn to an own function
like all other compression/decompression methods in iphc.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reworks the handling of compression/decompression of traffic
class and flow label handling. The current method is hard to understand,
also doesn't checks if we can read the buffer from skb length.
I tried to put the shifting operations into static inline functions and
comment each steps which I did there to make it hopefully somewhat more
readable. The big mess to deal with that is the that the ipv6 header
bring the order "DSCP + ECN" but iphc uses "ECN + DSCP". Additional the
DCSP + ECN bits are splitted in ipv6_hdr inside the priority and
flow_lbl[0] fields.
I tested these compressions by using fakelb 802.15.4 driver and
manipulate the tc and flow label fields manually in function
"__ip6_local_out" before the skb will be send to lower layers. Then I
looked up the tc and flow label fields in wireshark on a wpan and lowpan
interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch has the main goal to delete shift operations. Instead we
doing masks and equals afterwards. E.g. for the SAM evaluation we
masking only the SAM value which fits in iphc1 byte, then comparing with
all possible SAM values over a switch case statement. We will not
shifting the SAM value to somewhat readable anymore.
Additional this patch slighty change the naming style like RFC 6282,
e.g. TTL to HLIM and we will drop an errno now if CID flag is set,
because we don't support it.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This macro is used at 802.15.4 6LoWPAN only and can be replaced by
memcmp with the interface broadcast address.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the IPHC related defines for doing bit manipulation
from global 6lowpan header to the iphc file which should the only one
implementation which use these defines.
Also move next header compression defines to their nhc implementation.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the iphc setting of next header commpression bit inside
iphc functionality. Setting of IPHC bits should be happen at iphc.c file
only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the lowpan_fetch_skb_u8 function for getting the iphc
bytes. Instead we using the generic which has a len parameter to tell
the amount of bytes to fetch.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the lowpan_header_decompress function by removing
inklayer related information from parameters. This is currently for
supporting short and extended address for iphc handling in 802154.
We don't support short address handling anyway right now, but there
exists already code for handling short addresses in
lowpan_header_decompress.
The address parameters are also changed to a void pointer, so 6LoWPAN
linklayer specific code can put complex structures as these parameters
and cast it again inside the generic code by evaluating linklayer type
before. The order is also changed by destination address at first and
then source address, which is the same like all others functions where
destination is always the first, memcpy, dev_hard_header,
lowpan_header_compress, etc.
This patch also moves the fetching of iphc values from 6LoWPAN linklayer
specific code into the generic branch.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the lowpan_header_compress function by removing
unused parameters like "len" and drop static value parameters of
protocol type. Instead we really check the protocol type inside inside
the skb structure. Also we drop the use of IEEE802154_ADDR_LEN which is
link-layer specific. Instead we using EUI64_ADDR_LEN which should always
the default case for now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the LOWPAN_IPHC_MAX_HC_BUF_LEN define which
represent the worst-case supported IPHC buffer length. It's used to
allocate the stack buffer space for creating the IPHC header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a check if the dataroom of skb contains a dispatch value
by checking if skb->len != 0. This patch also change the dispatch
evaluation by the recently introduced helpers for checking the common
6LoWPAN dispatch values for IPv6 and IPHC header.
There was also a forgotten else branch which should drop the packet if
no matching dispatch is available.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will use kzfree instead kfree for security related
information which can be offered by acccident.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commit 89cbb0638e introduced support for deferred connection
parameter removal when unpairing by removing them only once an
existing connection gets disconnected. However, it failed to address
the scenario when we're *not* connected and do an unpair operation.
What makes things worse is that most user space BlueZ versions will
first issue a disconnect request and only then unpair, meaning the
buggy code will be triggered every time. This effectively causes the
kernel to resume scanning and reconnect to a device for which we've
removed all keys and GATT database information.
This patch fixes the issue by adding the missing call to the
hci_conn_params_del() function to a branch which handles the case of
no existing connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.19+
Before the vendor specific setup stage is triggered call back into the
core to trigger an internal notification event. That event is used to
send an index update to the monitor interface. With that specific event
it is possible to update userspace with manufacturer information before
any HCI command has been executed. This is useful for early stage
debugging of vendor specific initialization sequences.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HIDP specs define an idle-timeout which automatically disconnects a
device. This has always been implemented in the HIDP layer and forced a
synchronous shutdown of the hidp-scheduler. This works just fine, but
lacks a forced disconnect on the underlying l2cap channels. This has been
broken since:
commit 5205185d46
Author: David Herrmann <dh.herrmann@gmail.com>
Date: Sat Apr 6 20:28:47 2013 +0200
Bluetooth: hidp: remove old session-management
The old session-management always forced an l2cap error on the ctrl/intr
channels when shutting down. The new session-management skips this, as we
don't want to enforce channel policy on the caller. In other words, if
user-space removes an HIDP device, the underlying channels (which are
*owned* and *referenced* by user-space) are still left active. User-space
needs to call shutdown(2) or close(2) to release them.
Unfortunately, this does not work with idle-timeouts. There is no way to
signal user-space that the HIDP layer has been stopped. The API simply
does not support any event-passing except for poll(2). Hence, we restore
old behavior and force EUNATCH on the sockets if the HIDP layer is
disconnected due to idle-timeouts (behavior of explicit disconnects
remains unmodified). User-space can still call
getsockopt(..., SO_ERROR, ...)
..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can
still be re-used (which nobody does so far, though). Therefore, the API
still supports the new behavior, but with this patch it's also compatible
to the old implicit channel shutdown.
Cc: <stable@vger.kernel.org> # 3.10+
Reported-by: Mark Haun <haunma@keteu.org>
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the diagnostic settings are not persistent over HCI Reset, then this
quirk can be used to tell the Bluetoth core about it. This will ensure
that the settings are programmed correctly when the controller is
powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are LE devices on the market that start off by announcing their
public address and then once paired switch to using private address.
To be interoperable with such devices we should simply trust the fact
that we're receiving an IRK from them to indicate that they may use
private addresses in the future. Instead, simply tie the persistency
to the bonding/no-bonding information the same way as for LTKs and
CSRKs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending diagnostic messages directly to the monitor socket might cause
issues for devices processing their messages in interrupt context. So
instead of trying to directly forward them, queue them up with the other
HCI packets and lets them be processed by the sockets at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using the HCI_CHANNEL_RAW, restrict the packet types to valid ones
from the Bluetooth specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_VENDOR_PKT quirk was needed for BPA-100/105 devices that send
these messages. Now that there is support for proper diagnostic channel
this quirk is no longer needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The exit label performs device_unlock(&dev->dev);, which will fail when dev
is NULL, and nfc_put_device(dev);, which is not useful when dev is NULL, so
just exit the function immediately.
Problem found using scripts/coccinelle/null/deref_null.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
Commit 044a832a77 ("xfrm: Fix local error reporting crash
with interfamily tunnels") moved the setting of skb->protocol
behind the last access of the inner mode family to fix an
interfamily crash. Unfortunately now skb->protocol might not
be set at all, so we fail dispatch to the inner address family.
As a reault, the local error handler is not called and the
mtu value is not reported back to userspace.
We fix this by setting skb->protocol on message size errors
before we call xfrm_local_error.
Fixes: 044a832a77 ("xfrm: Fix local error reporting crash with interfamily tunnels")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. Most relevantly, updates for the nfnetlink_log to integrate with
conntrack, fixes for cttimeout and improvements for nf_queue core, they are:
1) Remove useless ifdef around static inline function in IPVS, from
Eric W. Biederman.
2) Simplify the conntrack support for nfnetlink_queue: Merge
nfnetlink_queue_ct.c file into nfnetlink_queue_core.c, then rename it back
to nfnetlink_queue.c
3) Use y2038 safe timestamp from nfnetlink_queue.
4) Get rid of dead function definition in nf_conntrack, from Flavio
Leitner.
5) Attach conntrack support for nfnetlink_log.c, from Ken-ichirou MATSUZAWA.
This adds a new NETFILTER_NETLINK_GLUE_CT Kconfig switch that
controls enabling both nfqueue and nflog integration with conntrack.
The userspace application can request this via NFULNL_CFG_F_CONNTRACK
configuration flag.
6) Remove unused netns variables in IPVS, from Eric W. Biederman and
Simon Horman.
7) Don't put back the refcount on the cttimeout object from xt_CT on success.
8) Fix crash on cttimeout policy object removal. We have to flush out
the cttimeout extension area of the conntrack not to refer to an unexisting
object that was just removed.
9) Make sure rcu_callback completion before removing nfnetlink_cttimeout
module removal.
10) Fix compilation warning in br_netfilter when no nf_defrag_ipv4 and
nf_defrag_ipv6 are enabled. Patch from Arnd Bergmann.
11) Autoload ctnetlink dependencies when NFULNL_CFG_F_CONNTRACK is
requested. Again from Ken-ichirou MATSUZAWA.
12) Don't use pointer to previous hook when reinjecting traffic via
nf_queue with NF_REPEAT verdict since it may be already gone. This
also avoids a deadloop if the userspace application keeps returning
NF_REPEAT.
13) A bunch of cleanups for netfilter IPv4 and IPv6 code from Ian Morris.
14) Consolidate logger instance existence check in nfulnl_recv_config().
15) Fix broken atomicity when applying configuration updates to logger
instances in nfnetlink_log.
16) Get rid of the .owner attribute in our hook object. We don't need
this anymore since we're dropping pending packets that have escaped
from the kernel when unremoving the hook. Patch from Florian Westphal.
17) Remove unnecessary rcu_read_lock() from nf_reinject code, we always
assume RCU read side lock from .call_rcu in nfnetlink. Also from Florian.
18) Use static inline function instead of macros to define NF_HOOK() and
NF_HOOK_COND() when no netfilter support in on, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini found hang with rds-ping while testing RDS over TCP. Its
a corner case and doesn't happen always. The issue is not reproducible
with IB transport. Its clear from below dump why we see it with RDS TCP.
[<ffffffff8153b7e5>] do_tcp_setsockopt+0xb5/0x740
[<ffffffff8153bec4>] tcp_setsockopt+0x24/0x30
[<ffffffff814d57d4>] sock_common_setsockopt+0x14/0x20
[<ffffffffa096071d>] rds_tcp_xmit_prepare+0x5d/0x70 [rds_tcp]
[<ffffffffa093b5f7>] rds_send_xmit+0xd7/0x740 [rds]
[<ffffffffa093bda2>] rds_send_pong+0x142/0x180 [rds]
[<ffffffffa0939d34>] rds_recv_incoming+0x274/0x330 [rds]
[<ffffffff810815ae>] ? ttwu_queue+0x11e/0x130
[<ffffffff814dcacd>] ? skb_copy_bits+0x6d/0x2c0
[<ffffffffa0960350>] rds_tcp_data_recv+0x2f0/0x3d0 [rds_tcp]
[<ffffffff8153d836>] tcp_read_sock+0x96/0x1c0
[<ffffffffa0960060>] ? rds_tcp_recv_init+0x40/0x40 [rds_tcp]
[<ffffffff814d6a90>] ? sock_def_write_space+0xa0/0xa0
[<ffffffffa09604d1>] rds_tcp_data_ready+0xa1/0xf0 [rds_tcp]
[<ffffffff81545249>] tcp_data_queue+0x379/0x5b0
[<ffffffffa0960cdb>] ? rds_tcp_write_space+0xbb/0x110 [rds_tcp]
[<ffffffff81547fd2>] tcp_rcv_established+0x2e2/0x6e0
[<ffffffff81552602>] tcp_v4_do_rcv+0x122/0x220
[<ffffffff81553627>] tcp_v4_rcv+0x867/0x880
[<ffffffff8152e0b3>] ip_local_deliver_finish+0xa3/0x220
This happens because rds_send_xmit() chain wants to take
sock_lock which is already taken by tcp_v4_rcv() on its
way to rds_tcp_data_ready(). Commit db6526dcb5 ("RDS: use
rds_send_xmit() state instead of RDS_LL_SEND_FULL") which
was trying to opportunistically finish the send request
in same thread context.
But because of above recursive lock hang with RDS TCP,
the send work from rds_send_pong() needs to deferred to
worker to avoid lock up. Given RDS ping is more of connectivity
test than performance critical path, its should be ok even
for transport like IB.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the time of commit fff3269907 ("tcp: reflect SYN queue_mapping into
SYNACK packets") we had little ways to cope with SYN floods.
We no longer need to reflect incoming skb queue mappings, and instead
can pick a TX queue based on cpu cooking the SYNACK, with normal XPS
affinities.
Note that all SYNACK retransmits were picking TX queue 0, this no longer
is a win given that SYNACK rtx are now distributed on all cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dhcp server may provide parameters to a client from a pool of IP
addresses and using a shared rootfs, or provide a specific set of
parameters for a specific client, usually using the MAC address to
identify each client individually. The dhcp protocol also specifies
a client-id field which can be used to determine the correct
parameters to supply when no MAC address is available. There is
currently no way to tell the kernel to supply a specific client-id,
only the userspace dhcp clients support this feature, but this can
not be used when the network is needed before userspace is available
such as when the root filesystem is on NFS.
This patch is to be able to do something like "ip=dhcp,client_id_type,
client_id_value", as a kernel parameter to enable the kernel to
identify itself to the server.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since at least before 2.6.30, tty drivers that do not drop the tty lock
while closing cannot observe ASYNC_CLOSING set while holding the
tty lock; this includes the tty driver's open() and hangup() methods,
since the tty core calls these methods holding the tty lock.
For these drivers, waiting for ASYNC_CLOSING to clear while opening
is not required, since this condition cannot occur. Similarly, even
when the open() method drops and reacquires the tty lock after
blocking, ASYNC_CLOSING cannot be set (again, for drivers that
do not drop the tty lock while closing).
Now that tty port drivers no longer drop the tty lock while closing
(since 'tty: Remove tty_wait_until_sent_from_close()'), the same
conditions apply: waiting for ASYNC_CLOSING to clear while opening
is not required, nor is re-checking ASYNC_CLOSING after dropping and
reacquiring the tty lock while blocking (eg., in *_block_til_ready()).
Note: The ASYNC_CLOSING flag state is still maintained since several
bitrotting drivers use it for (dubious) other purposes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This merge resolves conflicts with 75aec9df3a ("bridge: Remove
br_nf_push_frag_xmit_sk") as part of Eric Biederman's effort to improve
netns support in the network stack that reached upstream via David's
net-next tree.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
net/bridge/br_netfilter_hooks.c
Commit 00590fdd5b introduced RCU locking in list type and in
doing so introduced a memory allocation in list_set_add, which
is done in an atomic context, due to the fact that ipset rcu
list modifications are serialised with a spin lock. The reason
why we can't use a mutex is that in addition to modifying the
list with ipset commands, it's also being modified when a
particular ipset rule timeout expires aka garbage collection.
This gc is triggered from set_cleanup_entries, which in turn
is invoked from a timer thus requiring the lock to be bh-safe.
Concretely the following call chain can lead to "sleeping function
called in atomic context" splat:
call_ad -> list_set_uadt -> list_set_uadd -> kzalloc(, GFP_KERNEL).
And since GFP_KERNEL allows initiating direct reclaim thus
potentially sleeping in the allocation path.
To fix the issue change the allocation type to GFP_ATOMIC, to
correctly reflect that it is occuring in an atomic context.
Fixes: 00590fdd5b ("netfilter: ipset: Introduce RCU locking in list type")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
This patch cleanses whitespace around arithmetical operators.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use tabs instead of spaces to indent code.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use tabs instead of spaces to indent second line of parameters in
function definitions.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Correct whitespace layout of ternary operators in the netfilter-ipv4
code.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Whitespace cleansing: Labels should not be indented.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A recent change to the dst_output handling caused a new warning
when the call to NF_HOOK() is the only used of a local variable
passed as 'dev', and CONFIG_NETFILTER is disabled:
net/ipv6/ip6_output.c: In function 'ip6_output':
net/ipv6/ip6_output.c:135:21: warning: unused variable 'dev' [-Wunused-variable]
The reason for this is that the NF_HOOK macro in this case does
not reference the variable at all, and the call to dev_net(dev)
got removed from the ip6_output function. To avoid that warning now
and in the future, this changes the macro into an equivalent
inline function, which tells the compiler that the variable is
passed correctly but still unused.
The dn_forward function apparently had the same problem in
the past and added a local workaround that no longer works
with the inline function. In order to avoid a regression, we
have to also remove the #ifdef from decnet in the same patch.
Fixes: ede2059dba ("dst: Pass net into dst->output")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All verdict handlers make use of the nfnetlink .call_rcu callback
so rcu readlock is already held.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We don't care if module is being unloaded anymore since hook unregister
handling will destroy queue entries using that hook.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
since commit 8405a8fff3 ("netfilter: nf_qeueue: Drop queue entries on
nf_unregister_hook") all pending queued entries are discarded.
So we can simply remove all of the owner handling -- when module is
removed it also needs to unregister all its hooks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Reflects ceph.git commit 7bfb7f9025a8ee0d2305f49bf0336d2424da5b5b.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This newly introduced netdevice notifier is called before actual change
upper happens. That provides a possibility for notifier handlers to
know upper change will happen and react to it, including possibility to
forbid the change. That is valuable for drivers which can check if the
upper device linkage is supported and forbid that in case it is not.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under stress, a close() on a listener can trigger the
WARN_ON(sk->sk_ack_backlog) in inet_csk_listen_stop()
We need to test if listener is still active before queueing
a child in inet_csk_reqsk_queue_add()
Create a common inet_child_forget() helper, and use it
from inet_csk_reqsk_queue_add() and inet_csk_listen_stop()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's reduce the confusion about inet_csk_reqsk_queue_drop() :
In many cases we also need to release reference on request socket,
so add a helper to do this, reducing code size and complexity.
Fixes: 4bdc3d6614 ("tcp/dccp: fix behavior of stale SYN_RECV request sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c69736696c.
At the time of above commit, tcp_req_err() and dccp_req_err()
were dead code, as SYN_RECV request sockets were not yet in ehash table.
Real bug was fixed later in a different commit.
We need to revert to not leak a refcount on request socket.
inet_csk_reqsk_queue_drop_and_put() will be added
in following commit to make clean inet_csk_reqsk_queue_drop()
does not release the reference owned by caller.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_blackhole_route() does not initialize the newly allocated
rt6_info properly. This patch:
1. Call rt6_info_init() to initialize rt6i_siblings and rt6i_uncached
2. The current rt->dst._metrics init code is incorrect:
- 'rt->dst._metrics = ort->dst._metris' is not always safe
- Not sure what dst_copy_metrics() is trying to do here
considering ip6_rt_blackhole_cow_metrics() always returns
NULL
Fix:
- Always do dst_copy_metrics()
- Replace ip6_rt_blackhole_cow_metrics() with
dst_cow_metrics_generic()
3. Mask out the RTF_PCPU bit from the newly allocated blackhole route.
This bug triggers an oops (reported by Phil Sutter) in rt6_get_cookie().
It is because RTF_PCPU is set while rt->dst.from is NULL.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Phil Sutter <phil@nwl.cc>
Tested-by: Phil Sutter <phil@nwl.cc>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce rt6_info_init() to do the common init work for
'struct rt6_info' (after calling dst_alloc).
It is a prep work to fix the rt6_info init logic in the
ip6_blackhole_route().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sure that conn_params that were created just for
explicit_connect, will get properly deleted during cleanup.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After clearing the params->explicit_connect variable the parameters
may need to be either added back to the right list or potentially left
absent from both the le_reports and the le_conns lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices undergoing an explicit connect should not have their
conn_params struct removed by the mgmt Remove Device command. This
patch fixes the necessary checks in the command handler to correct the
behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The code should never directly call hci_conn_hash_del since many
cleanup & reference counting updates would be lost. Normally
hci_conn_del is the right thing to do, but in the case of a connection
doing LE scanning this could cause a deadlock due to doing a
cancel_delayed_work_sync() on the same work callback that we were
called from.
Connections in the LE scanning state actually need very little cleanup
- just a small subset of hci_conn_del. To solve the issue, refactor
out these essential pieces into a new hci_conn_cleanup() function and
call that from the two necessary places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.
This patch makes sure that unnecessary scan disable/enable commands
are not issued.
When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.
hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.
When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The function is void and static, so just ifdef its contents
instead of duplicating the declaration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Printing "N/A mBi" is strange - print just "N/A" instead.
Also add a missing opening parenthesis.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of having a lot of places that free ignored requests
and then return REG_REQ_OK, make reg_process_hint() process
REG_REQ_IGNORE by freeing the request, and let functions it
calls return that instead of freeing.
This also fixes a leak when a second (different) country IE
hint was ignored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function can only deal with treatment values OK and ALREADY_SET
so make the callees not return anything else and warn if they do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a built-in regulatory database, there may be little point
in also calling out to CRDA and failing if the system is configured
that way. Allow removing CRDA support to save ~1K kernel size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change made in the previous commit revealed a small flaw in the way
the node FSM is updated. When the function tipc_node_link_down() is
called for the last link to a node, we should check whether this was
caused by a local reset or by a received RESET message from the peer.
In the latter case, we can directly issue a PEER_LOST_CONTACT_EVT to
the node FSM, so that it is ready to re-establish contact. If this is
not done, the peer node will sometimes have to go through a second
establish cycle before the link becomes stable.
We fix this in this commit by conditionally issuing the mentioned
event in the function tipc_node_link_down(). We also move LINK_RESET
FSM even away from the link_reset() function and into the caller
function, partially because it is easier to follow the code when state
changes are gathered at a limited number of locations, partially
because there will be cases in future commits where we don't want the
link to go RESET mode when link_reset() is called.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is taken down because of a node local event, such as
disabling of a bearer or an interface, we currently leave it to the
peer node to discover the broken communication. The default time for
such failure discovery is 1.5-2 seconds.
If we instead allow the terminating link endpoint to send out a RESET
message at the moment it is reset, we can achieve the impression that
both endpoints are going down instantly. Since this is a very common
scenario, we find it worthwhile to make this small modification.
Apart from letting the link produce the said message, we also have to
ensure that the interface is able to transmit it before TIPC is
detached. We do this by performing the disabling of a bearer in three
steps:
1) Disable reception of TIPC packets from the interface in question.
2) Take down the links, while allowing them so send out a RESET message.
3) Disable transmission of TIPC packets on the interface.
Apart from this, we now have to react on the NETDEV_GOING_DOWN event,
instead of as currently the NEDEV_DOWN event, to ensure that such
transmission is possible during the teardown phase.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link establishing, just like link teardown, is a non-atomic action, in
the sense that discovering that conditions are right to establish a link,
and the actual adding of the link to one of the node's send slots is done
in two different lock contexts. The link FSM is designed to help bridging
the gap between the two contexts in a safe manner.
We have now discovered a weakness in the implementaton of this FSM.
Because we directly let the link go from state LINK_ESTABLISHING to
state LINK_ESTABLISHED already in the first lock context, we are unable
to distinguish between a fully established link, i.e., a link that has
been added to its slot, and a link that has not yet reached the second
lock context. It may hence happen that a manual intervention, e.g., when
disabling an interface, causes the function tipc_node_link_down() to try
removing the link from the node slots, decrementing its active link
counter etc, although the link was never added there in the first place.
We solve this by delaying the actual state change until we reach the
second lock context, inside the function tipc_node_link_up(). This
makes it possible for potentail callers of __tipc_node_link_down() to
know if they should proceed or not, and the problem is solved.
Unforunately, the situation described above also has a second problem.
Since there by necessity is a tipc_node_link_up() call pending once
the node lock has been released, we must defuse that call by setting
the link back from LINK_ESTABLISHING to LINK_RESET state. This forces
us to make a slight modification to the link FSM, which will now look
as follows.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | +----------------+ | |
| RESET_EVT| |RESET_EVT | |
| | | | |
| | | |ESTABLISH_EVT |
| | | +-------------+ | |
| | | | RESET_EVT | | |
| | | | | | |
| V V V | | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous commits, we are guaranteed that no packets
of type LINK_PROTOCOL or with illegal sequence numbers will be
attempted added to the link deferred queue. This makes it possible to
make some simplifications to the sorting algorithm in the function
tipc_skb_queue_sorted().
We also alter the function so that it will drop packets if one with
the same seqeunce number is already present in the queue. This is
necessary because we have identified weird packet sequences, involving
duplicate packets, where a legitimate in-sequence packet may advance to
the head of the queue without being detected and de-queued.
Finally, we make this function outline, since it will now be called only
in exceptional cases.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence number of an incoming packet is currently only checked
for less than, equality to, or bigger than the next expected number,
meaning that the receive window in practice becomes one half sequence
number cycle, or U16_MAX/2. This does not make sense, and may not even
be safe if there are extreme delays in the network. Any packet sent by
the peer during the ongoing cycle must belong inside his current send
window, or should otherwise be dropped if possible.
Since a link endpoint cannot know its peer's current send window, it
has to base this sanity check on a worst-case assumption, i.e., that
the peer is using a maximum sized window of 8191 packets. Using this
assumption, we now add a check that the sequence number is not bigger
than next_expected + TIPC_MAX_LINK_WIN. We also re-order the checks
done, so that the receive window test is performed before the gap test.
This way, we are guaranteed that no packet with illegal sequence numbers
are ever added to the deferred queue.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all packets received in tipc_link_rcv() are unconditionally
added to the packet deferred queue, whereafter that queue is walked and
all its buffers evaluated for delivery. This is both non-optimal and
and makes the queue sorting function unnecessary complex.
This commit changes the loop so that an arrived packet is evaluated
first, and added to the deferred queue only when a sequence number gap
is discovered. A non-empty deferred queue is walked until it is empty
or until its head's sequence number doesn't fit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During packet reception, the function tipc_link_rcv() adds its accepted
packets to a temporary buffer queue, before finally splicing this queue
into the lock protected input queue that will be delivered up to the
socket layer. The purpose is to reduce potential contention on the input
queue lock. However, since the vast majority of packets arrive in
sequence, they will anyway be added one by one to the input queue, and
the use of the temporary queue becomes a sub-optimization.
The only case where this queue makes sense is when unpacking buffers
from a bundle packet; here we want to avoid dozens of small buffers
to be added individually to the lock-protected input queue in a tight
loop.
In this commit, we remove the general usage of the temporary queue,
and keep it only for the packet unbundling case.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Work around connection namespace lookup bug related to RoCE
- Change usnic license to Dual GPL/BSD (was intended to be that way
all along, but wasn't clear, permission from contributors was
chased down)
- Fix an issue between NFSoRDMA and mlx5 that could cause an oops
- Fix leak of sendonly multicast groups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=usb1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"We have four batched up patches for the current rc kernel.
Two of them are small fixes that are obvious.
One of them is larger than I would like for a late stage rc pull, but
we found an issue in the namespace lookup code related to RoCE and
this works around the issue for now (we allow a lookup with a
namespace to succeed on RoCE since RoCE namespaces aren't implemented
yet). This will go away in 4.4 when we put in support for namespaces
in RoCE devices.
The last one is large in terms of lines, but is all legal and no
functional changes. Cisco needed to update their files to be more
specific about their license. They had intended the files to be dual
licensed as GPL/BSD all along, and specified that in their module
license tag, but their file headers were not up to par. They
contacted all of the contributors to get agreement and then submitted
a patch to update the license headers in the files.
Summary:
- Work around connection namespace lookup bug related to RoCE
- Change usnic license to Dual GPL/BSD (was intended to be that way
all along, but wasn't clear, permission from contributors was
chased down)
- Fix an issue between NFSoRDMA and mlx5 that could cause an oops
- Fix leak of sendonly multicast groups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: For sendonly join free the multicast group on leave
IB/cma: Accept connection without a valid netdev on RoCE
xprtrdma: Don't require LOCAL_DMA_LKEY support for fastreg
usnic: add missing clauses to BSD license
When the functions reg_set_rd_driver() and reg_set_rd_country_ie()
return with an error, the calling function already restores data
by calling restore_regulatory_settings(), so there's no need to
also schedule a timeout (which would lead to other side effects
such as indicating CRDA failed, which clearly isn't true.) Remove
the scheduling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of searching the built-in database only in the worker,
search it directly and return an error if the entry cannot be
found (or memory cannot be allocated.) This means that builtin
database queries no longer rely on the timeout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new name is more appropriate since in the case of a built-in
database it may not really rely on CRDA.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function reg_call_crda() can't actually validly return
REG_REQ_IGNORE as it does now when calling CRDA fails since
that return value isn't handled properly. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
netdev_for_each_lower_dev has to be called with rtnl mutex held. So
better enforce it in switchdev functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since spinlock is held here, defer the switchdev operation. Also, ensure
that defered switchdev ops are processed before port master device
is unlinked.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the attr usecase, the caller knows if he is holding RTNL and is
in atomic section. So let the called to decide the correct call variant.
This allows drivers to sleep inside their ops and wait for hw to get the
operation status. Then the status is propagated into switchdev core.
This avoids silent errors in drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When object is used in deferred work, we cannot use pointers in
switchdev object structures because the memory they point at may be already
used by someone else. So rather do local copy of the value.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caller should know if he can call attr_set directly (when holding RTNL)
or if he has to defer the att_set processing for later.
This also allows drivers to sleep inside attr_set and report operation
status back to switchdev core. Switchdev core then warns if status is
not ok, instead of silent errors happening in drivers.
Benefit from newly introduced switchdev deferred ops infrastructure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce infrastructure which will be used internally to defer ops.
Note that the deferred ops are queued up and either are processed by
scheduled work or explicitly by user calling deferred_process function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that dependencies are fulfilled before updating the logger
instance, otherwise we can leave things in intermediate state on errors
in nfulnl_recv_config().
[ Ken-ichirou reports that this is also fixing missing instance refcnt drop
on error introduced in his patch 914eebf2f4 ("netfilter: nfnetlink_log:
autoload nf_conntrack_netlink module NFQA_CFG_F_CONNTRACK config flag"). ]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Ken-ichirou MATSUZAWA <chamaken@gmail.com>
This patch consolidates the check for valid logger instance once we have
passed the command handling:
The config message that we receive may contain the following info:
1) Command only: We always get a valid instance pointer if we just
created it. In case that the instance is being destroyed or the
command is unknown, we jump to exit path of nfulnl_recv_config().
This patch doesn't modify this handling.
2) Config only: In this case, the instance must always exist since the
user is asking for configuration updates. If the instance doesn't exist
this returns -ENODEV.
3) No command and no configs are specified: This case is rare. The
user is sending us a config message with neither commands nor
config options. In this case, we have to check if the instance exists
and bail out otherwise. Before this patch, it was possible to send a
config message with no command and no config updates for an
unexisting instance without triggering an error. So this is the only
case that changes.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Ken-ichirou MATSUZAWA <chamaken@gmail.com>
In commit e3eea1eb47 ("tipc: clean up handling of message priorities")
we introduced a field in the packet header for keeping track of the
priority of fragments, since this value is not present in the specified
protocol header. Since the value so far only is used at the transmitting
end of the link, we have not yet officially defined it as part of the
protocol.
Unfortunately, the field we use for keeping this value, bits 13-15 in
in word 5, has turned out to be a poor choice; it is already used by the
broadcast protocol for carrying the 'network id' field of the sending
node. Since packet fragments also need to be transported across the
broadcast protocol, the risk of conflict is obvious, and we see this
happen when we use network identities larger than 2^13-1. This has
escaped our testing because we have so far only been using small network
id values.
We now move this field to bits 0-2 in word 9, a field that is guaranteed
to be unused by all involved protocols.
Fixes: e3eea1eb47 ("tipc: clean up handling of message priorities")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At listen() time, there is a small window where listener is visible with
a zero backlog, triggering a spurious "Possible SYN flooding on port"
message.
Nothing prevents us from setting the correct backlog.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we no longer hold listener lock in fast path, it is possible that a
child is created right after listener freed its bound port, if a close()
is done while incoming packets are processed.
__inet_inherit_port() must detect this and return an error,
so that caller can free the child earlier.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that kernel memory can leak into userspace by a
kmalloc, ethtool_get_strings, then copy_to_user sequence.
Avoid this by using kcalloc to zero fill the copied buffer.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJWHSq8AAoJEP5prqPJtc/HCyMH/R4PeAJoSwlQQVTKxDsdC/x1
Jxue9dMpEQhINoU1EpSQxaYIwg8zzFpQqcKVzoX9bgw5YdfAVgv/wrSW98Hwg/h5
OX+QYBAvhK/1Gk0+b7fwPF323osdD/8hn4lbQorB3gEYmE4+3kKh6ivlxGNa1LfW
VDfX23MhRF+iXFM64pnl7LR6BnflPQlGEKlWQgevR+cZDfEk+lDTRHjdAu/Hjokc
Nwo1agptCOsS5mgE/hyLhqBc6UXSN8ytoi5acP+KtnfnLtmgw/YEt7/2QQgOOTkf
T2zwCxFRQcePwoip7OXFwzkPsZkj3gn4XZCbTSErbqnQ28sFDbTQUTC1mB87f70=
=0GcF
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.4-20151013' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-09-17
this is a pull request of 4 patches for net-next/master.
Two patches are by Gerhard Bertelsmann, fixing some problems in the
sun4i driver. The patch by Arnd Bergmann stops using timeval for the
CAN broadcast manager. The last patch by Alexandre Belloni removes the
otherwise unused struct at91_can_data from the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* fast-xmit was not doing powersave filter clearing correctly,
disable fast-xmit while any such operations are still pending
* a debugfs file was broken due to some infrastructure changes
-----BEGIN PGP SIGNATURE-----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=Ziyp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Like last time, we have two small fixes:
* fast-xmit was not doing powersave filter clearing correctly,
disable fast-xmit while any such operations are still pending
* a debugfs file was broken due to some infrastructure changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
That file contains just a single function, which itself is just a
single statement to call a different function. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single caller of this function, so it can
be moved to the same file and made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 6e498158a8 ("tipc: move link synch and failover to link aggregation level")
we introduced a new mechanism for performing link failover and
synchronization. We have now detected a bug in this mechanism.
During link synchronization we use the arrival of any packet on
the tunnel link to trig a check for whether it has reached the
synchronization point or not. This has turned out to be too
permissive, since it may cause an arriving non-last SYNCH packet to
end the synch state, just to see the next SYNCH packet initiate a
new synch state with a new, higher synch point. This is not fatal,
but should be avoided, because it may significantly extend the
synchronization period, while at the same time we are not allowed
to send NACKs if packets are lost. In the worst case, a low-traffic
user may see its traffic stall until a LINK_PROTOCOL state message
trigs the link to leave synchronization state.
At the same time, LINK_PROTOCOL packets which happen to have a (non-
valid) sequence number lower than the tunnel link's rcv_nxt value will
be consistently dropped, and will never be able to resolve the situation
described above.
We fix this by exempting LINK_PROTOCOL packets from the sequence number
check, as they should be. We also reduce (but don't completely
eliminate) the risk of entering multiple synchronization states by only
allowing the (logically) first SYNCH packet to initiate a synchronization
state. This works independently of actual packet arrival order.
Fixes: commit 6e498158a8 ("tipc: move link synch and failover to link aggregation level")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the commit e2ca690b65 ("ipv4/icmp: redirect messages
can use the ingress daddr as source"), which tried to introduce a more
suitable behaviour for ICMP redirect messages generated by VRRP routers.
However RFC 5798 section 8.1.1 states:
The IPv4 source address of an ICMP redirect should be the address
that the end-host used when making its next-hop routing decision.
while said commit used the generating packet destination
address, which do not match the above and in most cases leads to
no redirect packets to be generated.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct whitespace layout of a pointer casting.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Correct whitespace layout of if statements.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When a TCP/DCCP listener is closed, its pending SYN_RECV request sockets
become stale, meaning 3WHS can not complete.
But current behavior is wrong :
incoming packets finding such stale sockets are dropped.
We need instead to cleanup the request socket and perform another
lookup :
- Incoming ACK will give a RST answer,
- SYN rtx might find another listener if available.
- We expedite cleanup of request sockets and old listener socket.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bug.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pkuy
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.3-2' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Two nfsd fixes, one for an RDMA crash, one for a pnfs/block protocol
bug"
* tag 'nfsd-4.3-2' of git://linux-nfs.org/~bfields/linux:
svcrdma: Fix NFS server crash triggered by 1MB NFS WRITE
nfsd/blocklayout: accept any minlength
The can subsystem communicates with user space using a bcm_msg_head
header, which contains two timestamps. This is problematic for
multiple reasons:
a) The structure layout is currently incompatible between 64-bit
user space and 32-bit user space, and cannot work in compat
mode (other than x32).
b) The timeval structure layout will change in 32-bit user
space when we fix the y2038 overflow problem by redefining
time_t to 64-bit, making new 32-bit user space incompatible
with the current kernel interface.
Cars last a long time and often use old kernels, so the actual
users of this code are the most likely ones to migrate to y2038
safe user space.
This tries to work around part of the problem by changing the
publicly visible user interface in the header, but not the binary
interface. Fortunately, the values passed around in the structure
are relative times and do not actually suffer from the y2038
overflow, so 32-bit is enough here.
We replace the use of 'struct timeval' with a newly defined
'struct bcm_timeval' that uses the exact same binary layout
as before and that still suffers from problem a) but not problem
b).
The downside of this approach is that any user space program
that currently assigns a timeval structure to these members
rather than writing the tv_sec/tv_usec portions individually
will suffer a compile-time error when built with an updated
kernel header. Fixing this error makes it work fine with old
and new headers though.
We could address problem a) by using '__u32' or 'int' members
rather than 'long', but that would have a more significant
downside in also breaking support for all existing 64-bit user
binaries that might be using this interface, which is likely
not acceptable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-can@vger.kernel.org
Cc: linux-api@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Correct whitespace layout of ternary operators in the netfilter-ipv6
code.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch cleanses whitespace around arithmetical operators.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use tabs instead of spaces to indent code.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use tabs instead of spaces to indent second line of parameters in
function definitions.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Whitespace cleansing: Labels should not be indented.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need to sync packet rx again after flushing the queue entries.
Otherwise, the following race could happen:
cpu1: nf_unregister_hook(H) called, H unliked from lists, calls
synchronize_net() to wait for packet rx completion.
Problem is that while no new nf_queue_entry structs that use H can be
allocated, another CPU might receive a verdict from userspace just before
cpu1 calls nf_queue_nf_hook_drop to remove this entry:
cpu2: receive verdict from userspace, lock queue
cpu2: unlink nf_queue_entry struct E, which references H, from queue list
cpu1: calls nf_queue_nf_hook_drop, blocks on queue spinlock
cpu2: unlock queue
cpu1: nf_queue_nf_hook_drop drops affected queue entries
cpu2: call nf_reinject for E
cpu1: kfree(H)
cpu2: potential use-after-free for H
Cc: Eric W. Biederman <ebiederm@xmission.com>
Fixes: 085db2c045 ("netfilter: Per network namespace netfilter hooks.")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ido Schimmel reported a problem with switchdev devices because of the
order change of del_nbp operations, more specifically the move of
nbp_vlan_flush() which deletes all vlans and frees vlgrp after the
rx_handler has been unregistered. So in order to fix this move
vlan_flush back where it was and make it destroy the rhtable after
NULLing vlgrp and waiting a grace period to make sure noone can see it.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ido Schimmel pointed out the vlan_vid_del() code in nbp_vlan_flush is
unnecessary (and is actually a remnant of the old vlan code) so we can
remove it.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fill_ifinfo is called by br_ifinfo_notify which can be called from
many contexts with different locks held, sometimes it relies upon
bridge's spinlock only which is a problem for the vlan code, so use
explicitly rcu for that to avoid problems.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge and port's vlgrp member is already used in RCU way, currently
we rely on the fact that it cannot disappear while the port exists but
that is error-prone and we might miss places with improper locking
(either RCU or RTNL must be held to walk the vlan_list). So make it
official and use RCU for vlgrp to catch offenders. Introduce proper vlgrp
accessors and use them consistently throughout the code.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with IPv4 support for VRFs added to IPv6 stack by replacing hardcoded
table ids with possibly device specific ones and manipulating the oif in
the flowi6. The flow flags are used to skip oif compare in nexthop lookups
if the device is enslaved to a VRF via the L3 master device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As originally written rt6_uncached_list_flush_dev makes no sense when
called with dev == NULL as it attempts to flush all uncached routes
regardless of network namespace when dev == NULL. Which is simply
incorrect behavior.
Furthermore at the point rt6_ifdown is called with dev == NULL no more
network devices exist in the network namespace so even if the code in
rt6_uncached_list_flush_dev were to attempt something sensible it
would be meaningless.
Therefore remove support in rt6_uncached_list_flush_dev for handling
network devices where dev == NULL, and only call rt6_uncached_list_flush_dev
when rt6_ifdown is called with a network device.
Fixes: 8d0b94afdc ("ipv6: Keep track of DST_NOCACHE routes in case of iface down/unregister")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLANs 0 and 4095 are reserved and shouldn't be used, add checks to
switchdev similar to the bridge. Also make sure ids above 4095 cannot
be passed either.
Fixes: 47f8328bb1 ("switchdev: add new switchdev bridge setlink")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't allow BRIDGE_VLAN_INFO_PVID flag in VLAN ranges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Elad Raz <eladr@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA driver may not provide the port_join_bridge and port_leave_bridge
functions, so don't warn in such case.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following "duelling syn" sequence between two peers A and B:
A B
SYN1 -->
<-- SYN2
SYN2ACK -->
Note that the SYN/ACK has already been sent out by TCP before
rds_tcp_accept_one() gets invoked as part of callbacks.
If the inet_addr(A) is numerically less than inet_addr(B),
the arbitration scheme in rds_tcp_accept_one() will prefer the
TCP connection triggered by SYN1, and will send a CLOSE for the
SYN2 (just after the SYN2ACK was sent).
Since B also follows the same arbitration scheme, it will send the SYN-ACK
for SYN1 that will set up a healthy ESTABLISHED connection on both sides.
B will also get a CLOSE for SYN2, which should result in the cleanup
of the TCP state machine for SYN2, but it should not trigger any
stale RDS-TCP callbacks (such as ->writespace, ->state_change etc),
that would disrupt the progress of the SYN2 based RDS-TCP connection.
Thus the arbitration scheme in rds_tcp_accept_one() should restore
rds_tcp callbacks for the winner before setting them up for the
new accept socket, and also make sure that conn->c_outgoing
is set to 0 so that we do not trigger any reconnect attempts on the
passive side of the tcp socket in the future, in conformance with
commit c82ac7e69e ("net/rds: RDS-TCP: only initiate reconnect attempt
on outgoing TCP socket.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP address passed to rds_bind() should be vetted by the
transport's ->laddr_check() for a previously bound transport.
This needs to be done to avoid cases where, for example,
the application has asked for an IB transport,
but the IP address passed to bind is only usable on
ethernet interfaces.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of -prev seems buggy. While packet was out our hook cannot be
removed but we have no way to know if the previous one is still valid.
So better not use ->prev at all. Since NF_REPEAT just asks to invoke
same hook function again, just do so, and continue with nf_interate
if we get an ACCEPT verdict.
A side effect of this change is that if nf_reinject(NF_REPEAT) causes
another REPEAT we will now drop the skb instead of a kernel loop.
However, NF_REPEAT loops would be a bug so this should not happen anyway.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If multiple scan plans were set for scheduled scan, do not restart
scheduled scan on reconfig because it is possible that some scan
plans were already completed and there is no need to run them all
over again. Instead, notify userspace that scheduled scan stopped
so it can configure new scan plans for scheduled scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.
When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For location and connectivity services, userspace would often like
to know the time when the BSS was last seen. The current "last seen"
value is calculated in a way that makes it less useful, especially
if the system suspended in the meantime.
Add the ability for the driver to report a real CLOCK_BOOTTIME stamp
that can then be reported to userspace (if present).
Drivers wishing to use this must be converted to the new API to call
cfg80211_inform_bss_data() or cfg80211_inform_bss_frame_data(). They
need to ensure the reported value is accurate enough even when the
frame might have been buffered in the device (e.g. firmware.)
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
[modified to use struct, inlines]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 30686bf7f5 ("mac80211: convert HW flags to unsigned long
bitmap") accidentally removed the newline delimiter from the hwflags
debugfs file. Fix this by adding back the newline between the HW flags.
Cc: stable@vger.kernel.org [4.2]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[fix commit log]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 5c48f12017.
Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently it's possible for someone to send a vlan range to the kernel
with the pvid flag set which will result in the pvid bouncing from a
vlan to vlan and isn't correct, it also introduces problems for hardware
where it doesn't make sense having more than 1 pvid. iproute2 already
enforces this, so let's enforce it on kernel-side as well.
Reported-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes ip6_route_info_create return err pointer instead of
returning the rt pointer by reference as suggested by Dave
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function nf_ct_frag6_gather is called on both the input and the
output paths of the networking stack. In particular ipv6_defrag which
calls nf_ct_frag6_gather is called from both the the PRE_ROUTING chain
on input and the LOCAL_OUT chain on output.
The addition of a net parameter makes it explicit which network
namespace the packets are being reassembled in, and removes the need
for nf_ct_frag6_gather to guess.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip_defrag is called on both the input and the output
paths of the networking stack. In particular conntrack when it is
tracking outbound packets from the local machine calls ip_defrag.
So add a struct net parameter and stop making ip_defrag guess which
network namespace it needs to defragment packets in.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_call_ra_chain is called early in the forwarding chain from
ip_forward and ip_mr_input, which makes skb->dev the correct
expression to get the input network device and dev_net(skb->dev) a
correct expression for the network namespace the packet is being
processed in.
Compute the network namespace and store it in a variable to make the
code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent TCP listener patches exposed a prior af_packet bug :
match_fanout_group() blindly assumes it is always safe
to cast sk to a packet socket to compare fanout with af_packet_priv
But SYNACK packets can be sent while attached to request_sock, which
are smaller than a "struct sock".
We can read non existent memory and crash.
Fixes: c0de08d042 ("af_packet: don't emit packet on orig fanout group")
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows configuring how the source address of ICMP
redirect messages is selected; by default the old behaviour is
retained, while setting icmp_redirects_use_orig_daddr force the
usage of the destination address of the packet that caused the
redirect.
The new behaviour fits closely the RFC 5798 section 8.1.1, and fix the
following scenario:
Two machines are set up with VRRP to act as routers out of a subnet,
they have IPs x.x.x.1/24 and x.x.x.2/24, with VRRP holding on to
x.x.x.254/24.
If a host in said subnet needs to get an ICMP redirect from the VRRP
router, i.e. to reach a destination behind a different gateway, the
source IP in the ICMP redirect is chosen as the primary IP on the
interface that the packet arrived at, i.e. x.x.x.1 or x.x.x.2.
The host will then ignore said redirect, due to RFC 1122 section 3.2.2.2,
and will continue to use the wrong next-op.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers need to implement both switchdev vlan ops and
vid_add/kill ndos. For that to work in bridge code, we need to try
switchdev op first when adding/deleting vlan id.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One 32bit hole is following skc_refcnt, use it.
skc_incoming_cpu can also be an union for request_sock rcv_wnd.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SO_INCOMING_CPU as added in commit 2c8c56e15d was a getsockopt() command
to fetch incoming cpu handling a particular TCP flow after accept()
This commits adds setsockopt() support and extends SO_REUSEPORT selection
logic : If a TCP listener or UDP socket has this option set, a packet is
delivered to this socket only if CPU handling the packet matches the specified
one.
This allows to build very efficient TCP servers, using one listener per
RX queue, as the associated TCP listener should only accept flows handled
in softirq by the same cpu.
This provides optimal NUMA behavior and keep cpu caches hot.
Note that __inet_lookup_listener() still has to iterate over the list of
all listeners. Following patch puts sk_refcnt in a different cache line
to let this iteration hit only shared and read mostly cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's useful to allow users to set fwmark for an individual packet,
without changing the socket state. The function this patch adds in
sock layer can be used by the protocols that need such a feature.
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let unprivileged users load and execute eBPF programs
teach verifier to prevent pointer leaks.
Verifier will prevent
- any arithmetic on pointers
(except R10+Imm which is used to compute stack addresses)
- comparison of pointers
(except if (map_value_ptr == 0) ... )
- passing pointers to helper functions
- indirectly passing pointers in stack to helper functions
- returning pointer from bpf program
- storing pointers into ctx or maps
Spill/fill of pointers into stack is allowed, but mangling
of pointers stored in the stack or reading them byte by byte is not.
Within bpf programs the pointers do exist, since programs need to
be able to access maps, pass skb pointer to LD_ABS insns, etc
but programs cannot pass such pointer values to the outside
or obfuscate them.
Only allow BPF_PROG_TYPE_SOCKET_FILTER unprivileged programs,
so that socket filters (tcpdump), af_packet (quic acceleration)
and future kcm can use it.
tracing and tc cls/act program types still require root permissions,
since tracing actually needs to be able to see all kernel pointers
and tc is for root only.
For example, the following unprivileged socket filter program is allowed:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += skb->len;
return 0;
}
but the following program is not:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += (u64) skb;
return 0;
}
since it would leak the kernel address into the map.
Unprivileged socket filter bpf programs have access to the
following helper functions:
- map lookup/update/delete (but they cannot store kernel pointers into them)
- get_random (it's already exposed to unprivileged user space)
- get_smp_processor_id
- tail_call into another socket filter program
- ktime_get_ns
The feature is controlled by sysctl kernel.unprivileged_bpf_disabled.
This toggle defaults to off (0), but can be set true (1). Once true,
bpf programs and maps cannot be accessed from unprivileged process,
and the toggle cannot be set back to false.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables to load nf_conntrack_netlink module if
NFULNL_CFG_F_CONNTRACK config flag is specified.
Signed-off-by: Ken-ichirou MATSUZAWA <chamas@h4.dion.ne.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that the NFS server advertises a maximum payload size of 1MB
for RPC/RDMA again, it crashes in svc_process_common() when NFS
client sends a 1MB NFS WRITE on an NFS/RDMA mount.
The server has set up a 259 element array of struct page pointers
in rq_pages[] for each incoming request. The last element of the
array is NULL.
When an incoming request has been completely received,
rdma_read_complete() attempts to set the starting page of the
incoming page vector:
rqstp->rq_arg.pages = &rqstp->rq_pages[head->hdr_count];
and the page to use for the reply:
rqstp->rq_respages = &rqstp->rq_arg.pages[page_no];
But the value of page_no has already accounted for head->hdr_count.
Thus rq_respages now points past the end of the incoming pages.
For NFS WRITE operations smaller than the maximum, this is harmless.
But when the NFS WRITE operation is as large as the server's max
payload size, rq_respages now points at the last entry in rq_pages,
which is NULL.
Fixes: cc9a903d91 ('svcrdma: Change maximum server payload . . .')
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=270
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Shirley Ma <shirley.ma@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
With the ARM mini2440_defconfig, the bridge netfilter code gets
built with both CONFIG_NF_DEFRAG_IPV4 and CONFIG_NF_DEFRAG_IPV6
disabled, which leads to a harmless gcc warning:
net/bridge/br_netfilter_hooks.c: In function 'br_nf_dev_queue_xmit':
net/bridge/br_netfilter_hooks.c:792:2: warning: label 'drop' defined but not used [-Wunused-label]
This gets rid of the warning by cleaning up the code to avoid
the respective #ifdefs causing this problem, and replacing them
with if(IS_ENABLED()) checks. I have verified that the resulting
object code is unchanged, and an additional advantage is that
we now get compile coverage of the unused functions in more
configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: dd302b59bd ("netfilter: bridge: don't leak skb in error paths")
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simon Horman says:
====================
Fourth Round of IPVS Updates for v4.4
please consider these build warning cleanups from David Ahern and myself.
They resolve some minor side effects of Eric Biederman' heroic work to
cleanup IPVS which you recently pulled: its queued up for v4.4 so no need
to worry about earlier kernel versions.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
--accept-local option works for res.type == RTN_LOCAL, which should be
from the local table, but there, the fib_info's nh->nh_scope =
RT_SCOPE_NOWHERE ( > RT_SCOPE_HOST). in fib_create_info().
if (cfg->fc_scope == RT_SCOPE_HOST) {
struct fib_nh *nh = fi->fib_nh;
/* Local address is added. */
if (nhs != 1 || nh->nh_gw)
goto err_inval;
nh->nh_scope = RT_SCOPE_NOWHERE; <===
nh->nh_dev = dev_get_by_index(net, fi->fib_nh->nh_oif);
err = -ENODEV;
if (!nh->nh_dev)
goto failure;
but in our rpfilter_lookup_reverse():
if (dev_match || flags & XT_RPFILTER_LOOSE)
return FIB_RES_NH(res).nh_scope <= RT_SCOPE_HOST;
if nh->nh_scope > RT_SCOPE_HOST, it will fail. --accept-local option
will never be passed.
it seems the test is bogus and can be removed to fix this issue.
if (dev_match || flags & XT_RPFILTER_LOOSE)
return FIB_RES_NH(res).nh_scope <= RT_SCOPE_HOST;
ipv6 does not have this issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The object and module refcounts are updated for each conntrack template,
however, if we delete the iptables rules and we flush the timeout
database, we may end up with invalid references to timeout object that
are just gone.
Resolve this problem by setting the timeout reference to NULL when the
custom timeout entry is removed from our base. This patch requires some
RCU trickery to ensure safe pointer handling.
This handling is similar to what we already do with conntrack helpers,
the idea is to avoid bumping the timeout object reference counter from
the packet path to avoid the cost of atomic ops.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On success, this shouldn't put back the timeout policy object, otherwise
we may have module refcount overflow and we allow deletion of timeout
that are still in use.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use SWITCHDEV_F_SKIP_EOPNOTSUPP to skip over ports in bridge that don't
support setting ageing_time (or setting bridge attrs in general).
If push fails, don't update ageing_time in bridge and return err to user.
If push succeeds, update ageing_time in bridge and run gc_timer now to
recalabrate when to run gc_timer next, based on new ageing_time.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to recurse over all the ports, skipping over unsupporting
ports. Without the change, the recursion would stop at first unsupported
port.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alive parameter of tcp_orphan_retries, indicates
whether the connection is assumed alive or not.
In the function and all places calling it is used as a boolean value.
Therefore this changes the type of alive to bool in the function
definition and all calling locations.
Since tcp_orphan_tries is a tcp_timer.c local function no change in
any other file or header is necessary.
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables adding of fdb entries pointing to the bridge device.
This can be used to propagate mac address of vlan interfaces
configured on top of the vlan filtering bridge.
Before:
$bridge fdb add 44:38:39:00:27:9f dev bridge
RTNETLINK answers: Invalid argument
After:
$bridge fdb add 44:38:39:00:27:9f dev bridge
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before recent TCP listener patches, we were updating listener
sk->sk_rxhash before the cloning of master socket.
children sk_rxhash was therefore correct after the normal 3WHS.
But with lockless listener, we no longer dirty/change listener sk_rxhash
as it would be racy.
We need to correctly update the child sk_rxhash, otherwise first data
packet wont hit correct cpu if RFS is used.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a clone of commit 2ab957492d ("ip_forward: Drop frames with
attached skb->sk") for ipv6.
This commit has exactly the same reasons as the above mentioned commit,
namely to prevent panics during netfilter reload or a misconfigured stack.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE point-to-point interfaces should also support ipv6 multicast. Setting
up default multicast routes on interface creation was forgotten. Add it.
Bugzilla: <https://bugzilla.kernel.org/show_bug.cgi?id=103231>
Cc: Julien Muchembled <jm@jmuchemb.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dumazet <ndumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with the FDB add operation, propagate the
switchdev_obj_port_fdb structure in the DSA drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the prepare phase is pushed down to the DSA drivers, propagate
it to the port_fdb_add function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push the prepare phase for FDB operations down to the DSA drivers, with
a new port_fdb_prepare function. Currently only mv88e6xxx is affected.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-10-08
Here's another set of Bluetooth & 802.15.4 patches for the 4.4 kernel.
802.15.4:
- Many improvements & fixes to the mrf24j40 driver
- Fixes and cleanups to nl802154, mac802154 & ieee802154 code
Bluetooth:
- New chipset support in btmrvl driver
- Fixes & cleanups to btbcm, btmrvl, bpa10x & btintel drivers
- Support for vendor specific diagnostic data through common API
- Cleanups to the 6lowpan code
- New events & message types for monitor channel
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selinux needs few changes to accommodate fact that SYNACK messages
can be attached to a request socket, lacking sk_security pointer
(Only syncookies are still attached to a TCP_LISTEN socket)
Adds a new sk_listener() helper, and use it in selinux and sch_fq
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported by: kernel test robot <ying.huang@linux.intel.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Eric Paris <eparis@parisplace.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit c0afd9ce4d ("fq_codel: fix return value of fq_codel_drop()")
->drop() is supposed to return the number of bytes it dropped,
but hhf_drop () returns the id of the bucket where it drops
a packet from.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Terry Lam <vtlam@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF socket filter programs may see junk in 'u32 cb[5]' area,
since it could have been used by protocol layers earlier.
For socket filter programs used in af_packet we need to clean
20 bytes of skb->cb area if it could be used by the program.
For programs attached to TCP/UDP sockets we need to save/restore
these 20 bytes, since it's used by protocol layers.
Remove SK_RUN_FILTER macro, since it's no longer used.
Long term we may move this bpf cb area to per-cpu scratch, but that
requires addition of new 'per-cpu load/store' instructions,
so not suitable as a short term fix.
Fixes: d691f9e8d4 ("bpf: allow programs to write to certain skb fields")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig currently controlling compilation of this code is:
net/sched/Kconfig:menuconfig NET_SCHED
net/sched/Kconfig: bool "QoS and/or fair queueing"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. We can
change to one of the other priority initcalls (subsys?) at any later
date, if desired.
We also delete the MODULE_LICENSE tag since all that information
is already contained at the top of the file in the comments.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig currently controlling compilation of this code is:
net/dcb/Kconfig:config DCB
net/dcb/Kconfig: bool "Data Center Bridging support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. We can
change to one of the other priority initcalls (subsys?) at any later
date, if desired.
We also delete the MODULE_LICENSE tag etc. since all that information
is (or is now) already contained at the top of the file in the comments.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Anish Bhatt <anish@chelsio.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Shani Michaeli <shanim@mellanox.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Makefile currently controlling compilation of this code lists
it under "obj-y" ...meaning that it currently is not being built as
a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. We can
change to one of the other priority initcalls (subsys?) at any later
date, if desired.
We can't remove module.h since the file uses other module related
stuff even though it is not modular itself.
We move the information from the MODULE_LICENSE tag to the top of the
file, since that information is not captured anywhere else. The
MODULE_ALIAS_NET_PF_PROTO becomes a no-op in the non modular case, so
it is removed.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Craig Gallek <kraig@google.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes lockdep_rtnl_is_held return bool due to this
particular function only using either one or zero as its return
value.
In another patch lockdep_is_held is also made return bool.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes dccp_bad_service_code return bool due to these
particular functions only using either one or zero as their return
value.
dccp_list_has_service is also been made return bool in this patchset.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes lockdep_nfnl_is_held return bool to improve
readability due to this particular function only using either
one or zero as its return value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes lockdep_genl_is_held return bool to improve
readability due to this particular function only using either
one or zero as its return value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we're sending more than one page via kernel_sendpage(), then set
MSG_SENDPAGE_NOTLAST between the pages so that we don't send suboptimal
frames (see commit 2f53384424 and commit 35f9c09fe9).
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When the controller is unconfigured (for example it does not have a
valid Bluetooth address), then the basic debugfs entries for dut_mode
and vendor_diag are not creates. Ensure they are created in __hci_init
and also __hci_unconf_init functions. One of them is called during setup
stage of a new controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Stream protocols such as TCP can often build up a backlog of data to be
read due to ordering. Combine this with the fact that some workloads such
as NFS read()-intensive workloads need to receive a lot of data per RPC
call, and it turns out that receiving the data from inside a softirq
context can cause starvation.
The following patch moves the TCP data receive into a workqueue context.
We still end up calling tcp_read_sock(), but we do so from a process
context, meaning that softirqs are enabled for most of the time.
With this patch, I see a doubling of read bandwidth when running a
multi-threaded iozone workload between a virtual client and server setup.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Move the TCP data receive loop out of xs_tcp_data_ready(). Doing so
will allow us to move the data receive out of the softirq context in
a set of followup patches.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
While recently arguing on a seccomp discussion that raw prandom_u32()
access shouldn't be exposed to unpriviledged user space, I forgot the
fact that SKF_AD_RANDOM extension actually already does it for some time
in cBPF via commit 4cd3675ebf ("filter: added BPF random opcode").
Since prandom_u32() is being used in a lot of critical networking code,
lets be more conservative and split their states. Furthermore, consolidate
eBPF and cBPF prandom handlers to use the new internal PRNG. For eBPF,
bpf_get_prandom_u32() was only accessible for priviledged users, but
should that change one day, we also don't want to leak raw sequences
through things like eBPF maps.
One thought was also to have own per bpf_prog states, but due to ABI
reasons this is not easily possible, i.e. the program code currently
cannot access bpf_prog itself, and copying the rnd_state to/from the
stack scratch space whenever a program uses the prng seems not really
worth the trouble and seems too hacky. If needed, taus113 could in such
cases be implemented within eBPF using a map entry to keep the state
space, or get_random_bytes() could become a second helper in cases where
performance would not be critical.
Both sides can trigger a one-time late init via prandom_init_once() on
the shared state. Performance-wise, there should even be a tiny gain
as bpf_user_rnd_u32() saves one function call. The PRNG needs to live
inside the BPF core since kernels could have a NET-less config as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Chema Gonzalez <chema@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no good reason why users outside of networking should not
be using this facility, f.e. for initializing their seeds.
Therefore, make it accessible from there as get_random_once().
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves values for all lowpan interface to the shared
implementation of 6lowpan. This patch also quietly fixes the forgotten
IFF_NO_QUEUE flag for the bluetooth 6LoWPAN interface. An identically
commit is 4afbc0d ("net: 6lowpan: convert to using IFF_NO_QUEUE") which
wasn't changed for bluetooth 6lowpan.
All 6lowpan interfaces should be virtual with IFF_NO_QUEUE, using EUI64
address length, the mtu size is 1280 (IPV6_MIN_MTU) and the netdev type
is ARPHRD_6LOWPAN.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit deaa0a6a93 ("net: Lookup actual route when oif is VRF device")
exposed a bug in __ip_route_output_key_hash for VRF devices: on FIB lookup
failure if the oif is specified the current logic drops to make_route on
the assumption that the route tables are wrong. For VRF/L3 master devices
this leads to wrong dst entries and route lookups. For example:
$ ip route ls table vrf-red
unreachable default
broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2
10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2
local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2
broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2
$ ip route get oif vrf-red 1.1.1.1
1.1.1.1 dev vrf-red src 10.0.0.2
cache
With this patch:
$ ip route get oif vrf-red 1.1.1.1
RTNETLINK answers: No route to host
which is the correct response based on the default route
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit c29390c6df ("xps: must clear sender_cpu before
forwarding"), we also need to clear the skb->sender_cpu when moving
from RX to TX via skb_do_redirect() due to the shared location of
napi_id (used on RX) and sender_cpu (used on TX).
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit c29390c6df ("xps: must clear sender_cpu before forwarding")
the skb->sender_cpu needs to be cleared before xmit.
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit c29390c6df ("xps: must clear sender_cpu before forwarding")
the skb->sender_cpu needs to be cleared when moving from Rx
Tx, otherwise kernel could crash.
Fixes: 2bd82484bb ("xps: fix xps for stacked devices")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Shilimkar says:
====================
RDS: connection scalability and performance improvements
[v4]
Re-sending the same patches from v3 again since my repost of
patch 05/14 from v3 was whitespace damaged.
[v3]
Updated patch "[PATCH v2 05/14] RDS: defer the over_batch work to
send worker" as per David Miller's comment [4] to avoid the magic
value usage. Patch now makes use of already available but unused
send_batch_count module parameter. Rest of the patches are same as
earlier version v2 [3]
[v2]:
Dropped "[PATCH 05/15] RDS: increase size of hash-table to 8K" from
earlier version [1]. I plan to address the hash table scalability using
re-sizable hash tables as suggested by David Laight and David Miller [2]
This series addresses RDS connection bottlenecks on massive workloads and
improve the RDMA performance almost by 3X. RDS TCP also gets a small gain
of about 12%.
RDS is being used in massive systems with high scalability where several
hundred thousand end points and tens of thousands of local processes
are operating in tens of thousand sockets. Being RC(reliable connection),
socket bind and release happens very often and any inefficiencies in
bind hash look ups hurts the overall system performance. RDS bin hash-table
uses global spin-lock which is the biggest bottleneck. To make matter worst,
it uses rcu inside global lock for hash buckets.
This is being addressed by simply using per bucket rw lock which makes the
locking simple and very efficient. The hash table size is still an issue and
I plan to address it by using re-sizable hash tables as suggested on the list.
For RDS RDMA improvement, the completion handling is revamped so that we
can do batch completions. Both send and receive completion handlers are
split logically to achieve the same. RDS 8K messages being one of the
key usecase, mr pool is adapted to have the 8K mrs along with default 1M
mrs. And while doing this, few fixes and couple of bottlenecks seen with
rds_sendmsg() are addressed.
Series applies against 4.3-rc1 as well net-next. Its tested on Oracle
hardware with IB fabric for both bcopy as well as RDMA mode. RDS TCP is
tested with iXGB NIC. Like last time, iWARP transport is untested with
these changes. The patchset is also available at below git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux.git net/rds/4.3-v3
As a side note, the IB HCA driver I used for testing misses at least 3
important patches in upstream to see the full blown IB performance and
am hoping to get that in mainline with help of them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The network namespace is already passed into dst_output pass it into
dst->output lwt->output and friends.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe Ricard
Kuba Pawlak
Robert Dolca
Eric Dumazet
Wu Fengguang
Jon Paul Maloy
David S. Miller
Neil Brown
Arnd Bergmann
Trond Myklebust
Robert Shearman
Roopa Prabhu
Li RongQing
Hiroshi Shimamoto
Paolo Abeni
Hannes Frederic Sowa
Andrew Shewmaker
lucien
Steffen Klassert
Sowmini Varadhan
Pravin B Shelar
Jorgen Hansen
Vivien Didelot
David Ahern
David Herrmann
Marcel Holtmann
Alexander Aring
Johan Hedberg
Joe Stringer
Renato Westphal
Arad, Ronen
James Morse
Doug Ledford
Elad Raz
Dan Carpenter
Gao feng
David Howells
Yuchung Cheng
Johannes Berg
Dean Jenkins
Julia Lawall
Linus Torvalds
santosh.shilimkar@oracle.com
Peter Hurley
Pablo Neira Ayuso
Nikolay Borisov
Ian Morris
Florian Westphal
Ilya Dryomov
Jiri Pirko
Martin KaFai Lau
Jakub Pawlowski
Joe Perches
Nikolay Aleksandrov
Eric W. Biederman
Avraham Stern
Dmitry Shmidt
Mohammed Shafi Shajakhan
Tamizh chelvam
Edward Jee
Alexei Starovoitov
Ken-ichirou MATSUZAWA
Chuck Lever
Scott Feldman
Richard Sailer
WANG Cong
Paul Gortmaker
Yaowei Bai
Daniel Borkmann