Initialize VLANs 0..4095 (Remove init for VID 4096).
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notifying hardware about newly bridged port vlan-aware changes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notifying hardware about bridge vlan-aware changes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding vlan_filtering attribute to allow hardware vendor to support
vlan-aware bridges. Vlan_filtering is a per-bridge attribute.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disallow adding interfaces to a bridge when vlan filtering operation
failed. Send the failure code to the user.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually when driver sends data to firmware it receives TX_DONE
(DN_LD_HOST_INT_STATUS) interrupt from firmware right away.
It's also observed that some times the fireware could delay
sending DN_LD_HOST_INT_STATUS interrupt. If driver sends data to
firmware during suspend processing and the TX_DONE interrupt is
delayed, it may come back at wrong time when SDIO host driver is
in the middle of suspending.
Block any data from stack while suspending. Also skip sending
data that are already in driver tx_queue.
Don't purge the skb queue on suspend to avoid intermittent music
after system resumes from S3.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For gpio=0xff (wake up host through SDIO interface) case,
gap=0xff means no delay (same as gap=0) for incoming data packet
to be sent to host after host sleep is activated.
Change it to the maximum delay to reduce the chance that RX
interrupt could be delivered while host controller suspends.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead, allow using string formatting with send_monitor_note()
and access init_utsname().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a qdisc is using per cpu stats (currently just the ingress
qdisc) only the bstats are being freed. This also free's the qstats.
Fixes: b0ab6f9275 ("net: sched: enable per cpu qstats")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LSR instruction cannot be used to perform a zero right shift since a
0 as the immediate value (imm5) in the LSR instruction encoding means
that a shift of 32 is perfomed. See DecodeIMMShift() in the ARM ARM.
Make the JIT skip generation of the LSR if a zero-shift is requested.
This was found using american fuzzy lop.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 538950a1b7 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This socket-lookup path did not pass along the skb in question
in my original BPF-based socket selection patch. The skb in the
udpN_lib_lookup2 path can be used for BPF-based socket selection just
like it is in the 'traditional' udpN_lib_lookup path.
udpN_lib_lookup2 kicks in when there are greater than 10 sockets in
the same hlist slot. Coincidentally, I chose 10 sockets per
reuseport group in my functional test, so the lookup2 path was not
excersised. This adds an additional set of tests with 20 sockets.
Fixes: 538950a1b7 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
Fixes: 3ca8e40299 ("soreuseport: BPF selection functional test")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit acf673a318 fixed a user triggerable free
memory scribble but in doing so replaced it with a different one that allows
the user to control the data and scribble even more.
sixpack_close is called by the tty layer in tty context. The tty context is
protected by sp_get() and sp_put(). However network layer activity via
sp_xmit() is not protected this way. We must therefore stop the queue
otherwise the user gets to dump a buffer mostly of their choice into freed
kernel pages.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization, when creating the send descriptor queues (SDQs),
we specify the CPU egress traffic class of each SDQ. The maximum number
of classes of this type is different in the two ASICs supported by this
PCI driver.
New firmware versions check this value is set correctly, which causes
errors on the Spectrum ASIC, as its max exposed egress traffic class is
lower than 7.
Solve this by setting this field to 3, which is an acceptable value for
both ASICs.
Note that we currently do not expose the QoS capabilities of the ASICs,
so setting this to an hardcoded value is OK for now.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SKF_AD_ALU_XOR_X ancillary is not like the other ancillary data
instructions since it XORs A with X while all the others replace A with
some loaded value. All the BPF JITs fail to clear A if this is used as
the first instruction in a filter. This was found using american fuzzy
lop.
Add a helper to determine if A needs to be cleared given the first
instruction in a filter, and use this in the JITs. Except for ARM, the
rest have only been compile-tested.
Fixes: 3480593131 ("net: filter: get rid of BPF_S_* enum")
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix IBSS which got broken over time
* new USB id for bcm43242 dongle
* arp offload configuration through inet notifier
ath9k
* add random number generator support (CONFIG_ATH9K_HWRNG)
iwlwifi
* Make scan parameters low latency aware
* Fix in the NL80211_FEATURE_FULL_AP_CLIENT_STATE state case
* Fix enable injection mode (Chaya Rachel)
* Various cleanups (Dan / Julia / myself)
* Allow to stay more time on popular channels (David Spinadel)
* Bug fixes for D0i3 (Eliad / Luca)
* Fixes for GO uAPSD (myself)
* Start of TSO support (myself)
* Rate control bug fixes (Eyal / Gregory)
* Start the work on 9000 devices (Johannes / Sara / Oren)
* Start the work on a new Tx queue allocation model (Liad)
* Debug infrastructure enhancements (Golan)
mwifiex
* add a debugfs file for chip reset
* advertise SMS4 cipher suite
* increase ap and station interface limit to 3
* enable MSI support on newer pcie devices (8897 onwards)
rtlwifi
* fix lots of module parameter usage
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWi5RxAAoJEG4XJFUm622bujQH/Rti4fRBnJcRt5EZAv/pvdIx
AGPcYQQfFbFRjzxjrcY30AYCC6OoID9n7BNtELIWabA6dQHWGJd2aebZGH85O4Eh
xgAty5CRf9E4+9MNiv+OqkL64/E6/YmSeOYiNSWl6SgRE4VYmexLXttpppImmoER
zowmtqzLSN/4l4yX5p2BVy3NAXN0R1WjYKNUXAJvJj59814upXf+XrOKCghzHIs4
2NE/aFoscscKWCSS3+MIIW4q9QWw7f8YvAdrO6k47LLkjm4+C/I5BeAlHUOEQUS7
xyoB/7KoHXlzRen8LmoL9SsqopTL2tKEjE/1f0QgLKOHXqpPRb4iKBFjsR94HJg=
=aeCM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-01-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
brcfmac
* fix IBSS which got broken over time
* new USB id for bcm43242 dongle
* arp offload configuration through inet notifier
ath9k
* add random number generator support (CONFIG_ATH9K_HWRNG)
iwlwifi
* Make scan parameters low latency aware
* Fix in the NL80211_FEATURE_FULL_AP_CLIENT_STATE state case
* Fix enable injection mode (Chaya Rachel)
* Various cleanups (Dan / Julia / myself)
* Allow to stay more time on popular channels (David Spinadel)
* Bug fixes for D0i3 (Eliad / Luca)
* Fixes for GO uAPSD (myself)
* Start of TSO support (myself)
* Rate control bug fixes (Eyal / Gregory)
* Start the work on 9000 devices (Johannes / Sara / Oren)
* Start the work on a new Tx queue allocation model (Liad)
* Debug infrastructure enhancements (Golan)
mwifiex
* add a debugfs file for chip reset
* advertise SMS4 cipher suite
* increase ap and station interface limit to 3
* enable MSI support on newer pcie devices (8897 onwards)
rtlwifi
* fix lots of module parameter usage
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc fails to see that the use of the 'last_offset' variable
in hns_nic_reuse_page() is used correctly and issues a bogus
warning:
drivers/net/ethernet/hisilicon/hns/hns_enet.c: In function 'hns_nic_reuse_page':
drivers/net/ethernet/hisilicon/hns/hns_enet.c:541:6: warning: 'last_offset' may be used uninitialized in this function [-Wmaybe-uninitialized]
This simplifies the function to make it more obvious what is
going on to both readers and compilers, which makes the warning
go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user was removed in commit
029f7f3b87 ("netfilter: ipv6: nf_defrag: avoid/free clone operations").
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
[I stole this patch from Eric Biederman. He wrote:]
> There is no defined mechanism to pass network namespace information
> into /sbin/bridge-stp therefore don't even try to invoke it except
> for bridge devices in the initial network namespace.
>
> It is possible for unprivileged users to cause /sbin/bridge-stp to be
> invoked for any network device name which if /sbin/bridge-stp does not
> guard against unreasonable arguments or being invoked twice on the
> same network device could cause problems.
[Hannes: changed patch using netns_eq]
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOCTL SIOCRTMSG does nothing but return EINVAL.
So comment it as unused.
SIOCRTMSG is only used in:
* net/ipv4/af_inet.c
* include/uapi/linux/sockios.h
inet_ioctl calls ip_rt_ioctl.
ip_rt_ioctl only handles SIOCADDRT and SIOCDELRT and returns -EINVAL
otherwise.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. The recordmcount change had an output that used sprintf() (incorrectly)
when it should have been a fprintf() to stderr.
2. The printk_formats file could crash if someone added a trace_printk()
in the core kernel, and also added one in a module. This does not
affect production kernels. Only kernels where developers add trace_printk()
for debugging can crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWi+jEAAoJEKKk/i67LK/8at0IAIMkbBMbRVjCM0tWTMM/2rZr
nD+2UOVZHDI7rSdhOC0yfRL041uiu/wI4DV6FAJZX8D5BumS7Wwv/GItwwNU3+TD
ZI6OG9f/6OxoC1jFUY8CvpSqAeV6uoro4heSzjprirSUsGwrFlTuHMt2NyEl0FvO
985HIzfTcb3yVFvsjm7Uyv1SsOdPL+BldDc46mgo8fXv3VYvvbqTP5NMkx7YyMdm
Dlo90b1nQ8bk3bjG4RvYmlnfK+HfbB2TD+rz3xJ+YaFRoJIov0/BzimeZaI3Aw/R
9TjLqwBN8ASVxc3A+/AQdUEserzXl7RSJHT/92YIQc8FkaS50cXX80Xk7ez0JVk=
=nb9G
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.4-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more fixes:
1. The recordmcount change had an output that used sprintf()
(incorrectly) when it should have been a fprintf() to stderr.
2. The printk_formats file could crash if someone added a
trace_printk() in the core kernel, and also added one in a module.
This does not affect production kernels. Only kernels where
developers add trace_printk() for debugging can crash"
* tag 'trace-v4.4-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix setting of start_index in find_next()
ftrace/scripts: Fix incorrect use of sprintf in recordmcount
Pull tile bugfix from Chris Metcalf:
"This fixes a bug that Sudip's buildbot found for tilepro allmodconfig.
I've tagged it for stable only back to 3.19, which was when most of
the other affected architectures added their support for working
around this issue"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: provide CONFIG_PAGE_SIZE_64KB etc for tilepro
Saeed Mahameed says:
====================
Introduce mlx5 ethernet timestamping
This patch series introduces the support for ConnectX-4 timestamping
and the PTP kernel interface.
Changes from V2:
net/mlx5_core: Introduce access function to read internal_timer
- Remove one line function
- Change function name
net/mlx5e: Add HW timestamping (TS) support:
- Data path performance optimization (caching tstamp struct in rq,sq)
- Change read/write_lock_irqsave to read/write_lock
- Move ioctl functions to en_clock file
- Changed overflow start algorithm according to comments from Richard
- Move timestamp init/cleanup to open/close ndos.
In details:
1st patch prevents the driver from modifying skb->data and SKB CB in
device xmit function.
2nd patch adds the needed low level helpers for:
- Fetching the hardware clock (hardware internal timer)
- Parsing CQEs timestamps
- Device frequency capability
3rd patch adds new en_clock.c file that handles all needed timestamping
operations:
- Internal clock structure initialization and other helper functions
- Added the needed ioctl for setting/getting the current timestamping
configuration.
- used this configuration in RX/TX data path to fill the SKB with
the timestamp.
4th patch Introduces PTP (PHC) support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PHC support to the mlx5_en driver. Use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled. This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.
The driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-4 card.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for enable/disable HW timestamping for incoming and/or
outgoing packets. To enable/disable HW timestamping appropriate
ioctl should be used. Currently HWTSTAMP_FILTER_ALL/NONE and
HWTSAMP_TX_ON/OFF only are supported. Make all relevant changes in
RX/TX flows to consider TS request and plant HW timestamps into
relevant structures.
Add internal clock for converting hardware timestamp to nanoseconds. In
addition, add a service task to catch internal clock overflow, to make
sure timestamping is accurate.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the SKB is cloned, or has an elevated users count, someone else
can be looking at it at the same time.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: use transport hashtable to replace association's with rhashtable
for telecom center, the usual case is that a server is connected by thousands
of clients. but if the server with only one enpoint(udp style) use the same
sport and dport to communicate with every clients, and every assoc in server
will be hashed in the same chain of global assoc hashtable due to currently we
choose dport and sport as the hash key.
when a packet is received, sctp_rcv try to find the assoc with sport and dport,
since that chain is too long to find it fast, it make the performance turn to
very low, some test data is as follow:
in server:
$./ss [start a udp style server there]
in client:
$./cc [start 2500 sockets to connect server with same port and different ip,
and use one of them to send data to server]
===== test on net-next
-- perf top
server:
55.73% [kernel] [k] sctp_assoc_is_match
6.80% [kernel] [k] sctp_assoc_lookup_paddr
4.81% [kernel] [k] sctp_v4_cmp_addr
3.12% [kernel] [k] _raw_spin_unlock_irqrestore
1.94% [kernel] [k] sctp_cmp_addr_exact
client:
46.01% [kernel] [k] sctp_endpoint_lookup_assoc
5.55% libc-2.17.so [.] __libc_calloc
5.39% libc-2.17.so [.] _int_free
3.92% libc-2.17.so [.] _int_malloc
3.23% [kernel] [k] __memset
-- spent time
time is 487s, send pkt is 10000000
we need to change the way to calculate the hash key, to use lport +
rport + paddr as the hash key can avoid this issue.
besides, this patchset will use transport hashtable to replace
association hashtable to lookup with rhashtable api. get transport
first then get association by t->asoc. and also it will make tcp
style work better.
===== test with this patchset:
-- perf top
server:
15.98% [kernel] [k] _raw_spin_unlock_irqrestore
9.92% [kernel] [k] __pv_queued_spin_lock_slowpath
7.22% [kernel] [k] copy_user_generic_string
2.38% libpthread-2.17.so [.] __recvmsg_nocancel
1.88% [kernel] [k] sctp_recvmsg
client:
11.90% [kernel] [k] sctp_hash_cmp
8.52% [kernel] [k] rht_deferred_worker
4.94% [kernel] [k] __pv_queued_spin_lock_slowpath
3.95% [kernel] [k] sctp_bind_addr_match
2.49% [kernel] [k] __memset
-- spent time
time is 22s, send pkt is 10000000
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_endpoint_lookup_assoc is called in the protection of sock lock
there is no need to call local_bh_disable in this function. so remove
them.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
transport hashtable will replace the association hashtable,
so association hashtable is not used in sctp any more, so
drop the codes about that.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traversal the transport rhashtable, get the association only once through
the condition assoc->peer.primary_path != transport.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
apply lookup apis to two functions, for __sctp_endpoint_lookup_assoc
and __sctp_lookup_association, it's invoked in the protection of sock
lock, it will be safe, but sctp_lookup_association need to call
rcu_read_lock() and to detect the t->dead to protect it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tranport hashtbale will replace the association hashtable to do the
lookup for transport, and then get association by t->assoc, rhashtable
apis will be used because of it's resizable, scalable and using rcu.
lport + rport + paddr will be the base hashkey to locate the chain,
with net to protect one netns from another, then plus the laddr to
compare to get the target.
this patch will provider the lookup functions:
- sctp_epaddr_lookup_transport
- sctp_addrs_lookup_transport
hash/unhash functions:
- sctp_hash_transport
- sctp_unhash_transport
init/destroy functions:
- sctp_transport_hashtable_init
- sctp_transport_hashtable_destroy
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the mgmt Start Limited Discovery command. Most
of existing Start Discovery code is reused since the only difference
is the presence of a 'limited' flag as part of the discovery state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the EIR parsing helper more general purpose, make it return
the found data and its length rather than just saying whether the data
was present or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This allows the build system to know that it can't attempt to
configure the Lustre virtual block device, for example, when tilepro
is using 64KB pages (as it does by default). The tilegx build
already provided those symbols.
Previously we required that the tilepro hypervisor be rebuilt with
a different hardcoded page size in its headers, and then Linux be
rebuilt using the updated hypervisor header. Now we allow each of
the hypervisor and Linux to be built independently. We still check
at boot time to ensure that the page size provided by the hypervisor
matches what Linux expects.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: stable@vger.kernel.org [3.19+]
On 2015/11/06, Dmitry Vyukov reported a deadlock involving the splice
system call and AF_UNIX sockets,
http://lists.openwall.net/netdev/2015/11/06/24
The situation was analyzed as
(a while ago) A: socketpair()
B: splice() from a pipe to /mnt/regular_file
does sb_start_write() on /mnt
C: try to freeze /mnt
wait for B to finish with /mnt
A: bind() try to bind our socket to /mnt/new_socket_name
lock our socket, see it not bound yet
decide that it needs to create something in /mnt
try to do sb_start_write() on /mnt, block (it's
waiting for C).
D: splice() from the same pipe to our socket
lock the pipe, see that socket is connected
try to lock the socket, block waiting for A
B: get around to actually feeding a chunk from
pipe to file, try to lock the pipe. Deadlock.
on 2015/11/10 by Al Viro,
http://lists.openwall.net/netdev/2015/11/10/4
The patch fixes this by removing the kern_path_create related code from
unix_mknod and executing it as part of unix_bind prior acquiring the
readlock of the socket in question. This means that A (as used above)
will sb_start_write on /mnt before it acquires the readlock, hence, it
won't indirectly block B which first did a sb_start_write and then
waited for a thread trying to acquire the readlock. Consequently, A
being blocked by C waiting for B won't cause a deadlock anymore
(effectively, both A and B acquire two locks in opposite order in the
situation described above).
Dmitry Vyukov(<dvyukov@google.com>) tested the original patch.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commands run in a vrf context are not failing as expected on a route lookup:
root@kenny:~# ip ro ls table vrf-red
unreachable default
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
ping: Warning: source address might be selected on device other than vrf-red.
PING 10.100.1.254 (10.100.1.254) from 0.0.0.0 vrf-red: 56(84) bytes of data.
--- 10.100.1.254 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 999ms
Since the vrf table does not have a route for 10.100.1.254 the ping
should have failed. The saddr lookup causes a full VRF table lookup.
Propogating a lookup failure to the user allows the command to fail as
expected:
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
connect: No route to host
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek says:
====================
Faster SO_REUSEPORT
This series contains two optimizations for the SO_REUSEPORT feature:
Faster lookup when selecting a socket for an incoming packet and
the ability to select the socket from the group using a BPF program.
This series only includes the UDP path. I plan to submit a follow-up
including the TCP path if the implementation in this series is
acceptable.
Changes in v4:
- pskb_may_pull is unnecessary with pskb_pull (per Alexei Starovoitov)
Changes in v3:
- skb_pull_inline -> pskb_pull (per Alexei Starovoitov)
- reuseport_attach* -> sk_reuseport_attach* and simple return statement
syntax change (per Daniel Borkmann)
Changes in v2:
- Fix ARM build; remove unnecessary include.
- Handle case where protocol header is not in linear section (per
Alexei Starovoitov).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This program will build classic and extended BPF programs and
validate the socket selection logic when used with
SO_ATTACH_REUSEPORT_CBPF and SO_ATTACH_REUSEPORT_EBPF.
It also validates the re-programing flow and several edge cases.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose socket options for setting a classic or extended BPF program
for use when selecting sockets in an SO_REUSEPORT group. These options
can be used on the first socket to belong to a group before bind or
on any socket in the group after bind.
This change includes refactoring of the existing sk_filter code to
allow reuse of the existing BPF filter validation checks.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include a struct sock_reuseport instance when a UDP socket binds to
a specific address for the first time with the reuseport flag set.
When selecting a socket for an incoming UDP packet, use the information
available in sock_reuseport if present.
This required adding an additional field to the UDP source address
equality function to differentiate between exact and wildcard matches.
The original use case allowed wildcard matches when checking for
existing port uses during bind. The new use case of adding a socket
to a reuseport group requires exact address matching.
Performance test (using a machine with 2 CPU sockets and a total of
48 cores): Create reuseport groups of varying size. Use one socket
from this group per user thread (pinning each thread to a different
core) calling recvmmsg in a tight loop. Record number of messages
received per second while saturating a 10G link.
10 sockets: 18% increase (~2.8M -> 3.3M pkts/s)
20 sockets: 14% increase (~2.9M -> 3.3M pkts/s)
40 sockets: 13% increase (~3.0M -> 3.4M pkts/s)
This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sock_reuseport is an optional shared structure referenced by each
socket belonging to a reuseport group. When a socket is bound to an
address/port not yet in use and the reuseport flag has been set, the
structure will be allocated and attached to the newly bound socket.
When subsequent calls to bind are made for the same address/port, the
shared structure will be updated to include the new socket and the
newly bound socket will reference the group structure.
Usually, when an incoming packet was destined for a reuseport group,
all sockets in the same group needed to be considered before a
dispatching decision was made. With this structure, an appropriate
socket can be found after looking up just one socket in the group.
This shared structure will also allow for more complicated decisions to
be made when selecting a socket (eg a BPF filter).
This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of fixes from Ido.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge port attributes are offloaded to hardware when invoked with SELF
flag set, but it really makes no sense to reflect them when port is not
bridged.
Allow a user to change these attribute only when port is bridged and
initialize them correctly when joining or leaving a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the bridge status of physical ports in the appropriate functions, to
be consistent with LAG join/leave and vPorts joining/leaving bridge.
Also, remove the error messages in these two functions, as we already
emit errors in both the single functions they call.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for us to fail when joining or leaving a bridge, so let
the user know about that by returning NOTIFY_BAD, as already done for
LAG join/leave and 802.1D bridges.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set PVID to 1 in mlxsw_sp_port_vlan_init(), so we can remove this
statement.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cphy_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz
Chin-Ran Lo
Johannes Berg
John Fastabend
Rabin Vincent
Craig Gallek
One Thousand Gnomes
Ido Schimmel
David S. Miller
Arnd Bergmann
Florian Westphal
Hannes Frederic Sowa
xypron.glpk@gmx.de
Linus Torvalds
Eran Ben Elisha
Achiad Shochat
Xin Long
Johan Hedberg
Chris Metcalf
Rainer Weikusat
David Ahern
hayeswang
Julia Lawall