Граф коммитов

92 Коммитов

Автор SHA1 Сообщение Дата
Fabien Dessenne 60630924bb hwspinlock: stm32: enable clock at probe
Set the clock during probe and keep its control during suspend / resume
operations.
This fixes an issue when CONFIG_PM is not set and where the clock is
never enabled.

Make use of devm_ functions to simplify the code.

Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211011135836.1045437-1-fabien.dessenne@foss.st.com
2021-11-17 16:12:44 -06:00
Wilken Gottwalt 3c881e05c8 hwspinlock: add sun6i hardware spinlock support
Adds the sun6i_hwspinlock driver for the hardware spinlock unit found in
most of the sun6i compatible SoCs.

This unit provides at least 32 spinlocks in hardware. The implementation
supports 32, 64, 128 or 256 32bit registers. A lock can be taken by
reading a register and released by writing a 0 to it. This driver
supports all 4 spinlock setups, but for now only the first setup (32
locks) seem to exist in available devices. This spinlock unit is shared
between all ARM cores and the embedded companion core. All of them can
take/release a lock with a single cycle operation. It can be used to
sync access to devices shared by the ARM cores and the companion core.

There are two ways to check if a lock is taken. The first way is to read
a lock. If a 0 is returned, the lock was free and is taken now. If an 1
is returned, the caller has to try again. Which means the lock is taken.
The second way is to read a 32bit wide status register where every bit
represents one of the 32 first locks. According to the datasheets this
status register supports only the 32 first locks. This is the reason the
first way (lock read/write) approach is used to be able to cover all 256
locks in future devices. The driver also reports the amount of supported
locks via debugfs.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/bfd2b97307c2321b15c09683f4bd5e1fcc792f13.1615713499.git.wilken.gottwalt@posteo.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-05-27 22:19:42 -05:00
Arnd Bergmann 1cb8f3e2d8 hwspinlock: remove sirf driver
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.

Cc: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/linux-arm-kernel/20210120124812.2800027-1-arnd@kernel.org/T/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120132537.2285157-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-03-17 21:22:06 -05:00
Suman Anna b9ddb2500e hwspinlock: omap: Add support for K3 AM64x SoCs
The AM64x SoC contains a HwSpinlock IP instance in the MAIN domain,
and is a minor variant of the IP on the current TI K3 SoCs such as
AM64x, J721E or J7200 SoCs. The IP is not built with the K3 safety
feature in hardware, and has slightly different integration into
the overall SoC.

Add the support for this IP through a new compatible.

Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210209172240.2305-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-02-09 11:36:50 -06:00
Baolin Wang c3e9b463b4 hwspinlock: sirf: Remove the redundant 'of_match_ptr'
Remove the the redundant 'of_match_ptr' macro to fix below warning
when the CONFIG_OF is not selected.

All warnings:
drivers/hwspinlock/sirf_hwspinlock.c:87:34: warning: unused variable
'sirf_hwpinlock_ids' [-Wunused-const-variable]

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/250d35cb489c3c4c066f7ce256d27f36712a1979.1591618255.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-12-10 13:34:40 -06:00
Chunyan Zhang 8266b80926 hwspinlock: sprd: fixed warning of unused variable 'sprd_hwspinlock_of_match'
The macro function of_match_ptr() is NULL if CONFIG_OF is not set, in this
case Clang compiler would complain the of_device_id variable is unused.

Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d8c8bbbb1a ("hwspinlock: sprd: Add hardware spinlock driver")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201112070410.14810-1-zhang.lyra@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-11-17 21:42:13 -06:00
Chunyan Zhang 8308678ebd hwspinlock: sprd: use module_platform_driver() instead postcore initcall
The hardware spinlock devices are defined in the DT, there's no need for
init calls order, remove boilerplate code by using module_platform_driver.

Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201030034654.15775-3-zhang.lyra@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-11-02 18:04:06 -06:00
Baolin Wang 3116a9931f hwspinlock: sprd: Remove redundant header files
Remove redundant header files.

Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/1590991552-93643-1-git-send-email-baolin.wang@linux.alibaba.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-10-26 10:17:54 -05:00
Bjorn Andersson 7a1e6fb1c6 hwspinlock: qcom: Allow mmio usage in addition to syscon
In modern Qualcomm platforms the mutex region of the TCSR is forked off
into its own block, all with a offset of 0 and stride of 4096, and in
some of these platforms no other registers in this region is accessed
from Linux.

So add support for directly memory mapping this register space, to avoid
the need to represent this block using a syscon.

Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622075956.171058-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-07-13 22:29:28 -07:00
Ezequiel Garcia 285e74ab4f hwspinlock: Simplify Kconfig
Every hwspinlock driver is expected to depend on the
hwspinlock core, so it's possible to simplify the
Kconfig, factoring out the HWSPINLOCK dependency.

Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20200414220943.6203-1-ezequiel@collabora.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-06-21 00:36:03 -07:00
Gustavo A. R. Silva ef17f5193e hwspinlock: hwspinlock_internal.h: Replace zero-length array with flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")

Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200319213839.GA10669@embeddedor.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-03-25 22:30:46 -07:00
Baolin Wang ffd0bbfb37 hwspinlock: Allow drivers to be built with COMPILE_TEST
Allow drivers to be built with COMPILE_TEST.

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/5a95c3de07ef020a4e2f2776fa5adb00637ee387.1581324976.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-03-25 22:30:46 -07:00
Baolin Wang cb36017a8b hwspinlock: sirf: Use devm_hwspin_lock_register() to register hwlock controller
Use devm_hwspin_lock_register() to register the hwlock controller instead of
unregistering the hwlock controller explicitly when removing the device.

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/8f94e67b5f9af20a93418a2fc9cc71b194f1285c.1578453662.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-21 16:16:36 -08:00
Baolin Wang 8f2a0dc87d hwspinlock: sirf: Remove redundant PM runtime functions
Since the hwspinlock core has changed the PM runtime to be optional, and
the SIRF hardware spinlock has no pm runtime requirement, thus remove
these redundant PM runtime functions.

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/c921e391aa2a652d8d6ae0e4041202cec9d917e7.1578453662.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-21 16:16:30 -08:00
Baolin Wang 77d99a6a9d hwspinlock: sirf: Change to use devm_platform_ioremap_resource()
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together, which can simpify the code.

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/dfa043f317c609a6172468ac11598968dd751bce.1578453662.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-21 16:16:16 -08:00
Baolin Wang 42f291ebfd hwspinlock: omap: Use devm_kzalloc() to allocate memory
Use devm_kzalloc() to allocate memory, which can simplify the error
handling.

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/c066ad704c1a5fd52c3002cac80ddd59b3901b01.1578453062.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-21 16:11:25 -08:00
Baolin Wang bf2740068a hwspinlock: omap: Change to use devm_platform_ioremap_resource()
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together, which can simpify the code.
Meanwhile renaming the error label to make more sense after removing
iounmap().

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/6c09c5034a7e68fdfc22d2cb5daa375bccb33a66.1578453062.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-21 16:11:11 -08:00
Baolin Wang ed0611a604 hwspinlock: qcom: Use devm_hwspin_lock_register() to register hwlock controller
Use devm_hwspin_lock_register() to register the hwlock controller instead of
unregistering the hwlock controller explicitly when removing the device.

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/d69ad8611a68b0cac3c927d19901f3c113c5435c.1578452735.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-21 16:10:07 -08:00
Baolin Wang 98ec52ad81 hwspinlock: qcom: Remove redundant PM runtime functions
Since the hwspinlock core has changed the PM runtime to be optional, and
the Qualcomm hardware spinlock has no pm runtime requirement, thus remove
these redundant PM runtime functions.

Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/e0bb751feb7af709f92e52a07d0e8ebcf1ee44ff.1578452735.git.baolin.wang7@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-21 16:09:10 -08:00
Yangtao Li d4824486b6 hwspinlock: stm32: convert to devm_platform_ioremap_resource
Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191228191541.26999-1-tiny.windzz@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-12-28 20:43:23 -08:00
Baolin Wang 9d399f0c52 hwspinlock: u8500_hsem: Remove redundant PM runtime implementation
Since the hwspinlock core has changed the PM runtime to be optional, thus
remove the redundant PM runtime implementation in the u8500 HWSEM driver.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-11-08 16:42:26 -08:00
Baolin Wang 4d0c1c5732 hwspinlock: sprd: Remove redundant PM runtime implementation
Since the hwspinlock core has changed the PM runtime to be optional, thus
remove the redundant PM runtime implementation in the Spreadtrum hwlock
driver.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-11-08 16:42:11 -08:00
Baolin Wang a6fc49051c hwspinlock: Let the PM runtime can be optional
Now some hwspinlock controllers did not have the requirement to implement
the PM runtime, but drivers must enable the PM runtime to comply with the
hwspinlock core.

Thus we can change the PM runtime support to be optional by validating
the -EACCES error number which means the PM runtime is not enabled, and
removing the return value validating of pm_runtime_put(). So that we
can remove some redundant PM runtime code in drivers.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-11-08 16:42:00 -08:00
Baolin Wang b2547dce4d hwspinlock: Remove BUG_ON() from the hwspinlock core
The original code use BUG_ON() to validate the parameters when locking
or unlocking one hardware lock, but we should not crash the whole kernel
though the hwlock parameters are incorrect, instead we can return
the error number for users and give some warning.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-11-08 16:41:13 -08:00
Baolin Wang b674a30bf8 hwspinlock: sprd: Use devm_hwspin_lock_register() to register hwlock controller
Use devm_hwspin_lock_register() to register the hwlock controller instead of
unregistering the hwlock controller explicitly when removing the device.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-10-04 21:10:26 -07:00
Baolin Wang b4d64193d4 hwspinlock: sprd: Use devm_add_action_or_reset() for calls to clk_disable_unprepare()
Use devm_add_action_or_reset() for calls to clk_disable_unprepare(),
which can simplify the error handling.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-10-04 21:09:52 -07:00
Baolin Wang 3070c41643 hwspinlock: sprd: Check the return value of clk_prepare_enable()
We must check the return value of clk_prepare_enable() to make sure the
hardware spinlock controller can be enabled successfully, otherwise we
should return error.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-10-04 21:07:44 -07:00
Baolin Wang 74cfa956cb hwspinlock: sprd: Change to use devm_platform_ioremap_resource()
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together, which can simpify the code.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-10-04 21:07:19 -07:00
Baolin Wang acc98c1f2a hwspinlock: u8500_hsem: Use devm_hwspin_lock_register() to register hwlock controller
Use devm_hwspin_lock_register() to register the hwlock controller instead of
unregistering the hwlock controller explicitly when removing the device.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-10-04 20:20:41 -07:00
Baolin Wang 637bcd19be hwspinlock: u8500_hsem: Use devm_kzalloc() to allocate memory
Use devm_kzalloc() to allocate memory.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-10-04 20:20:20 -07:00
Baolin Wang 5ee45e0c89 hwspinlock: u8500_hsem: Change to use devm_platform_ioremap_resource()
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together, which can simpify the code.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-10-04 20:20:18 -07:00
Fabien Dessenne 360aa640a5 hwspinlock: add the 'in_atomic' API
Add the 'in_atomic' mode which can be called from an atomic context.
This mode relies on the existing 'raw' mode (no lock, no preemption/irq
disabling) with the difference that the timeout is not based on jiffies
(jiffies won't increase when irq are disabled) but handled with
busy-waiting udelay() calls.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-06-29 21:08:14 -07:00
Fabien Dessenne 5cd69f13de hwspinlock: stm32: implement the relax() ops
Implement this optional ops, called by hwspinlock core while spinning on
a lock, between two successive invocations of trylock().

Reviewed-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-06-29 21:04:24 -07:00
Fabien Dessenne fbd7330c9f hwspinlock: ignore disabled device
Do not wait for hwspinlock device registration if it is not available
for use.

Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-06-29 12:05:06 -07:00
Suman Anna d4d98bba3e hwspinlock/omap: Add a trace during probe
Add a debug level trace statement in the OMAP HwSpinlock driver
probe function to print the number of hwlocks on a successful
registration.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-06-29 11:40:06 -07:00
Suman Anna 6fa154e282 hwspinlock/omap: Add support for TI K3 SoCs
A HwSpinlock IP is also present on the newer TI K3 AM65x and J721E
family of SoCs within the Main NavSS sub-module. Reuse the existing
OMAP Hwspinlock driver to extend the support for this IP on K3 AM65x
SoCs as well. The IP has slightly different bit-fields in the
SYSCONFIG and SYSSTATUS registers.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-06-29 11:40:04 -07:00
Wei Yongjun 4d5a91fd1f hwspinlock: fix return value check in stm32_hwspinlock_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: f24fcff1d2 ("hwspinlock: add STM32 hwspinlock device")
Acked-by: Benjamin Gaignard <benjamin.gaignard@gmail.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2019-01-03 11:42:10 -08:00
Benjamin Gaignard f24fcff1d2 hwspinlock: add STM32 hwspinlock device
This patch adds support of hardware semaphores for stm32mp1 SoC.
The hardware block provides 32 semaphores.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-12-05 12:45:21 -08:00
Baolin Wang ddb34f480d hwspinlock: Fix incorrect return pointers
The commit 4f1acd758b ("hwspinlock: Add devm_xxx() APIs to request/free
hwlock") introduces one bug, that will return one error pointer if failed
to request one hwlock, but we expect NULL pointer on error for consumers.
This patch will fix this issue.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-07-30 20:54:51 -07:00
Baolin Wang 38ce606533 hwspinlock: Fix one comment mistake
Fix one comment mistake with correct function names.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-06-26 13:46:34 -07:00
Baolin Wang c102780acd hwspinlock: Add devm_xxx() APIs to register/unregister one hwlock controller
This patch introduces devm_hwspin_lock_register() and devm_hwspin_lock_unregister()
interfaces to help to register or unregister one hardware spinlock controller, that
will help to simplify the cleanup code for hwspinlock drivers.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-06-26 13:46:23 -07:00
Baolin Wang 4f1acd758b hwspinlock: Add devm_xxx() APIs to request/free hwlock
This patch introduces some devm_xxx() APIs to help to request or free
the hwlocks, which will help to simplify the cleanup code for drivers
requesting one hwlock, ensuring that the hwlock is automatically freed
whenever the device is unbound.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-06-26 13:27:58 -07:00
Baolin Wang 5560f70cad hwspinlock: Add one new API to support getting a specific hwlock by the name
The hardware spinlock binding already supplied the 'hwlock-names' property
to match and get a specific hwlock, but did not supply one API for users
to get a specific hwlock by the hwlock name. So this patch introduces one
API to support this requirement.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-06-26 13:27:22 -07:00
Linus Torvalds 6f75edeadd hwspinlock updates for v4.18
In addition to migrating the files to use SPDX license headers this
 introduces the ability for clients to operate a hwlock without the
 framework taking any additional locks.
 -----BEGIN PGP SIGNATURE-----
 
 iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAlsevMIbHGJqb3JuLmFu
 ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3FqjgQAKWiDEoEw75RZnfmRAVB
 Ot8TgeUoj6CodjV0pe3fLYBYLKzJbEBiC8VfjFKeq9JwndPsGaCXqcnrKegl11pd
 /supYYzsAWT4YUZFsq0Y00mnNWKHLVL2VkKh4yPD+GaRuBDITKaurBnv3tB19ccG
 aeG5eS2bIhMhcaRaPVSRYlb34Zz8PssvlYefToUiNCuBI33D45fRSvvn5z3o5xAh
 ZL0qEBVG8BviPIPMwlp5w1PIC8Rz+eyZRmaH+fV5lewUqh32hzf4ynAIr0aDYug7
 tzFeSPqjxpvzRgZtocsJ2NqTm3jMEyzHL9X+Rt31ryN4flTROkCiWg4xDONvac7E
 fAq924WhvYqe2flNJjUR6azxjO0RsTx78LiAxZir43tvSjqdm3RTPgWOlCTdzP4u
 O5lDAm7c1QZISlKAXJewRccuUxg2XVdYa2tTBQalBqq9Ys1ZiMeWQ4UUNzvEIBji
 vlj2KguG5CgPrThhk/S11JCvG7Ti5frljebVasyF5nLX78bXPfTaBpPNre+kL6Ee
 4AylueOFeT5+Ft8a7quokzvBGUmlwYPq6jPAAL4TrU39SLIWxXRv3qDczBRe0j9G
 Xh6L8GVrUIEWxJz04OxtsgG/N3zNujjUTy/G3A3AZgM7Ijneu0xNKAjXNHfD2XNu
 pH2+HeF8vKQNB89gZJkF90XW
 =KYHF
 -----END PGP SIGNATURE-----

Merge tag 'hwlock-v4.18' of git://github.com/andersson/remoteproc

Pull hwspinlock updates from Bjorn Andersson:
 "In addition to migrating the files to use SPDX license headers this
  introduces the ability for clients to operate a hwlock without the
  framework taking any additional locks"

* tag 'hwlock-v4.18' of git://github.com/andersson/remoteproc:
  hwspinlock/u8500: Switch to SPDX license identifier
  hwspinlock: sprd: Switch to SPDX license identifier
  hwspinlock/sirf: Switch to SPDX license identifier
  hwspinlock: qcom: Switch to SPDX license identifier
  hwspinlock/omap: Switch to SPDX license identifier
  hwspinlock/core: Switch to SPDX license identifier
  hwspinlock: Introduce one new mode for hwspinlock
  hwspinlock: Convert to use 'switch' statement
2018-06-11 12:09:19 -07:00
Kees Cook 0ed2dd03b9 treewide: Use struct_size() for devm_kmalloc() and friends
Replaces open-coded struct size calculations with struct_size() for
devm_*, f2fs_*, and sock_* allocations. Automatically generated (and
manually adjusted) from the following Coccinelle script:

// Direct reference to struct field.
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(HANDLE, sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(HANDLE, struct_size(VAR, ELEMENT, COUNT), GFP)

// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(HANDLE, sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(HANDLE, struct_size(VAR, ELEMENT, COUNT), GFP)

// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@

- alloc(HANDLE, sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(HANDLE, CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-06 11:15:43 -07:00
Kees Cook acafe7e302 treewide: Use struct_size() for kmalloc()-family
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);

This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:

// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
//                      sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)

// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)

// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@

- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-06 11:15:43 -07:00
Suman Anna e759176c7f hwspinlock/u8500: Switch to SPDX license identifier
Use the appropriate SPDX license identifier in the U8500 HWSEM
driver source file and drop the previous boilerplate license text.

Cc: Mathieu J. Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-24 12:05:11 -07:00
Suman Anna 0c3e890b1e hwspinlock: sprd: Switch to SPDX license identifier
Use the appropriate SPDX license identifiers in the Spreadtrum hardware
spinlock driver source file and drop the previous boilerplate license text.

Cc: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-24 12:04:48 -07:00
Suman Anna 50a522805e hwspinlock/sirf: Switch to SPDX license identifier
Use the appropriate SPDX license identifier in the CSR's SIRF hardware
spinlock driver source file and drop the previous boilerplate license text.

Cc: Wei Chen <wei.chen@csr.com>
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-24 12:04:47 -07:00
Suman Anna 8ba01caeec hwspinlock: qcom: Switch to SPDX license identifier
Use the appropriate SPDX license identifier in the Qualcomm Hwspinlock
driver source file and drop the previous boilerplate license text.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-05-24 12:04:46 -07:00